Johnson Controls T9200 User manual

T9200
LCD Digital Thermostat
Installation Guide
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
Building E󰀩ciency
Headquarters: Milwaukee, Wisconsin, USA
Branch Officies: Principal Cities World-wide
Johnson Controls® is registered trademarks of Johnson Controls.
All other marks herein are the marks of their respective owners.
© Copyright 2020 Johnson Controls. All rights reserved. Any unauthorized use or copying is strictly prohibited.
www.johnsoncontrols.com
*241144600018B*
60.00
13.83
38.83
87.77
87.77
> 50 cm
> 150 cm
°C
ON / OFF
AUTO
°C/°F
1s
TiO2/ESP
3s Timer
Symbol
ON OFF
ON OFF
• Ambient
• 工作环境
MAX
40 °C
104 °F
MIN
0 °C
-32 °F
MAX
60 °C
140 °F
MIN
-10 °C
-14 °F
MAX 90% RH
MIN 10% RH
 

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
T9200-TF20-1JS0
GND
L
N
2-pipe FCU
2管制风机盘管
100-240 VAC 50/60Hz
OCC
Cool/
Heat
FAN
N Hi
Med
Low
LVAL1 VAL2
GND
L
N
4-pipe FCU
4管制风机盘管
100-240 VAC 50/60Hz
OCC
Cool Heat
FAN
N Hi
Med
Low
LVAL1 VAL2
GND
L
N
2-pipe 3-wire valve FCU
2管制风机盘管+3线开关阀
100-240 VAC 50/60Hz
OCC
On Off
FAN
N Hi
Med
Low
LVAL1 VAL2
GND
L
N
2-pipe FCU with TiO2/ESP
2管制风机盘管+TiO2/ESP
100-240 VAC 50/60Hz
OCC
TiO2
ESP
Cool/
Heat
FAN
N Hi
Med
Low
LVAL1 VAL2
GND
L
N
2-pipe FCU with floor heating
2管制风机盘管+地暖
100-240 VAC 50/60Hz
OCC
Floor
Heater
Cool/
Heat
FAN
N Hi
Med
Low
LVAL1 VAL2
GND
L
N
Water source heat pump
水源热泵
100-240 VAC 50/60Hz
OCC
CMP RV
RV = REVERSING VALVE CMP = COMPRESSOR
FAN
N Hi
Med
Low
LVAL1 VAL2
GND
L
N
Boiler/Floor heater
锅炉/地暖
100-240 VAC 50/60Hz
OCC
Boiler/
Floor heater
N Hi
Med
Low
LVAL1 VAL2
English 中文

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
T9200-TB21-1JS0
2-pipe FCU, three speed fan
2管制比例阀，三速风机
100-240 VAC 50/60Hz L
N
NR3L R1 R2
FAN
GND
OCCAO
Cool / Heater
HiMedLow
GND
L
N
2-pipe FCU (relay), ECM
2管制开关阀，ECM风机
0-10 V
100-240 VAC 50/60Hz
ECM
FAN
OCC
AO
Cool/Heat
NR3L R1 R2
Heat
GND
L
N
4-pipe FCU (relay), ECM fan
4管制开关阀，ECM风机
100-240 VAC 50/60Hz
ECM
FAN
OCC
AO
Cool
0-10 V
NR3L R1 R2
GND
L
N
2-pipe FCU, 3 wires (relay),
ECM fan
2管制三线阀，ECM风机
100-240 VAC 50/60Hz
ECM
FAN
OCC
AO
Off
On
0-10 V
NR3L R1 R2
GND
L
N
2-pipe FCU with floor heater,
ECM fan
2管制开关阀带地暖，ECM风机
100-240 VAC 50/60Hz
ECM
FAN
OCC
AO
Cool/
Heat
Floor
Heater
0-10 V
NR3L R1 R2
GND
L
N
2-pipe FCU with TiO2/ESP, ECM
2管制开关阀+ TiO2/ESP,
ECM风机
100-240 VAC 50/60Hz
ECM
FAN
OCC
AO
Cool/
Heat
0-10 V
TiO2
ESP
NR3L R1 R2
GND
L
N
water source heat pump
水源热泵
100-240 VAC 50/60Hz
OCCAO
ECM
FAN
0-10 V
CMP
RV
NR3L R1 R2
English 中文

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
图例：
NTC： 温度传感器
OCC： 门卡开关
ECMFAN：ECM风机
FAN： 风机
AO1： 模拟输出1
AO2： 模拟输出2
AI： 模拟输入/阀反馈
HEAT： 热水阀
COOL： 冷水阀
FLOORHEAT：地暖阀
LOW： 风机低速档位
MED： 风机中速档位
HI： 风机高速档位
TiO2： TiO2二氧化钛
ESP： Electro-staticPrecipitator静电除尘设备
CMP：Compressor压缩机
RV： ReversingValve换向阀
F-ON：风机开关
GND:地
L：火线
N：零线
V1：阀1
V2：阀2
TR:变压器
INSTALLATION INSTRUCTIONS FOR THE TECHNICIAN / FITTER
READ THIS INSTRUCTION SHEET AND THE SAFETY WARNINGS CAREFULLY BEFORE INSTALLING AND
SAVE IT FOR FUTURE USE
REPAIR AND REPLACEMENT
Do not attempt to repair the T9 Series thermostat. In case of an improperly functioning control, contact the nearest Johnson Controls® representative, and
specify the desired product code number. When contacting the supplier for a replacement please state the type/model number of the control located on the
data plate or cover label.
IMPORTANT
• Use this T9 Series thermostat only as an operating control. Where failure of malfunction of the T9 Series thermostat could lead to personal injury or
property damage to the controlled equipment or other property, additional precautions must be designed into the system. Incorporate and maintain other
devices such as supervisory or alarm systems or safety or limit controls intended to warn of, or protect against, failure or malfunction of the T9 Series
thermostat.
• Do not install this thermostat in condensing, wet, or damp environments. Moisture may cause damage to the thermostat.
• Do not remove PCB from the enclosure cover. Removing the PCB from the enclosure cover voids the product warranty.
• Make all wiring connections in accordance with local, national, and regional regulations. Do not exceed the T9 Series thermostat’s electrical ratings.
WARNING
Disconnect power supply before making electrical connections. Contact with components carrying hazardous voltages can cause electrical shock and may
result in severe personal injury or death.
• Risk of Electrical Shock: Ground the thermostat according to local, national, and regional regulations. Failure to ground the thermostat may result in
electrical shock and severe personal injury and death.
• Risk of Electrical Shock and Property Damage: Insulate and secure each unused wire lead before applying power to the thermostat.
Failure to insulate and secure each unused wire lead may result in property damage, electrical shock, and severe personal injury or death.
English 中文
M
T9200 interface
Callout Feature
APower button
BWorking mode button
CGeneral button
DFan speed adjustment button
EUp and down buttons

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
Callout Feature Callout Feature
ACooling JAlarm
BHeating KLock
CVentilation LValve status
DAuto mode MRemote sensor
EFan auto NCompressor protection
FFan speed Hi/Med/Low ODelay time
GTio2/ESP PTemperature and humidity value
HFloor heating QLow temperature protection
IOccupancy RDehumidify
INSTRUCTIONS
On/O󰀨 Setting: Press to turn on, press again to turn o󰀨, close the fan and valve.
Mode Selection: Press Mto change the working mode, for cooling, for heating, for venting, for auto cooling or
heating mode. is available only for 4-pipe application or 2-pipe application when BI-FUNCTION is Change Over Sensor
input.
Temperature Setting: Press either or button to increase or decrease the temperature by 0.5°C/1°F.
Fan Speed Adjustment: Press to switch the fan mode, auto ash, high , medium , low fan.
Note: Fan stops at Floor Heating Mode, until FH-FAN parameter set to enable, for single stage oor heating application only.
Delay On/O󰀨 setup: Press and hold button 5 seconds, then “ON” appears, press button to switch On or O󰀨 delay,
then press or to adjust the minute by 30 minutes.
Note: Time-On/O󰀨 setting performs only once within one day.
Delay On/O󰀨 Cancel: Press and hold button 5 seconds, then “ON” appears, press button to switch to check On or O󰀨
delay time, then press or adjust the time to “00:00”.
Lock setup: If Lock function is enabled, the thermostat locks automatically after 30 seconds unused.
Unlock function: Press and hold the button 5 seconds to unlock.
Tio2/ESP Manual: When Tio2/ESP function is set to Manual, press button once, to switch Tio2/ESP On or O󰀨.
English

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
English
PARAMETER SETTING
Press and button for 5 seconds at power o󰀨 mode to get in parameter list. Press to scroll forward and Mbutton to scroll backward in
the list and use and button to change the parameter value.
Code
T9200-
TB21-1JS0
T9200-
TF20-1JS0 Parameter name Default Function
04 ■ ■ MUTE 00
Enable/disable the beep when push touch button:
00: Disable
01: Enable
05 ■ ■ OFFSET 0°C/0°F
Offset to be compensate the room temperature:
Step: 0.5°C (1°F)
Range: -5~5°C (-9-9°F)
06 ■ ■ UNOCC-CLG-SP 26°C/
79°F
Cooling setpoint unoccupied mode.
Not available for Boiler application
Step: 0.5°C (1°F)
Range: 22~32°C (72-90°F)
07 ■ ■ UNOCC-HTG-SP 18°C/
64°F
Heating setpoint unoccupied mode.
Step: 0.5°C (1°F)
Range: 10~21°C (50-70°F)
08 ■SMPL-TM 10 s
Sample time,
PID parameter, only for PID
Range: 1~99 s
09 ■PB 5
Proportion band,
PID parameter, only for PID
Range: 1~10
10 ■KI 10
Integration parameter,
PID parameter, only for PID
Range: 0~99
11 ■ ■ BL-TIMER 30 Backlight timer
Range: 5~99S
12 ■ ■ PWR-F-RSTT 02
Restart after power failure:
00: OFF
01: ON
02: Recovery
13 ■ ■ TIO2ESP-CTL 00
TIO2ESP control:
00: Automatic
01: Manual
For TIO2ESP application
16 ■ ■ KEY-LOCK 00
Key lock function:
00: No lockout
01: Level 1 >Lock all keys
02: Level 2 >Lock the keys except Fan Speed and Temp Adjustment keys
03: Level 3 >Lock the ON/OFF and Clock keys
04: Level 4 >Lock the keys except ON/OFF key
17 ■ ■ TEMP-DISP 00
UI display room temperature or set point:
00: Room Temperature
01: Setpoint
18 ■ ■ UNIT 00
Unit selection:
00: IP
01: SI
20 ■ ■ SF-VERSION Software version, read only
USER SETTING

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
English
PARAMETER SETTING (PART 1/2)
Under Setting Page press button for 3 seconds to get in Service Page, the occupancy icon shows. Press to scroll forward and M
button to scroll backward in the list and use and button to change parameter value.
Code
T9200-
TB21-1JS0
T9200-
TF20-1JS0 Parameter name Default Function
02 ■ ■ FRST-PRT 00
Frost protection:
00: No
01: Yes
03 ■ ■ FH-FAN 00
Enable/disable fan output when floor heater:
00: Disable
01: Enable
04 ■ ■ APPLICATION 00
T9200- TF20-1JS0:
00: 2pipe application
01: 4pipe application
02: 2pipe 3-wire valve application
03: 2pipe with floor heating application
04: 2pipe with TiO2/ESP application
05: water source heat pump application
06: Boiler/Floor heater
T9200- TB21-1JS0:
00: 2-pipe FCU, three speed fan
01: 2-pipe FCU (relay), ECM fan
02: 4-pipe FCU (relay), ECM fan
03: 2-pipe 3 wire (relay), ECM fan
04: 2-pipe FCU with floor heater, ECM fan
05: 2-pipe FCU with TiO2/ESP, ECM fan
06: water source heat pump, ECM fan
05 ■ ■ DOWN-SET-LIMIT 5°C/
41°F
lower setpoint limit
Range: 0~36°C (32-97°F)
06 ■ ■ UP-SET-LIMIT 35°C/
95°F
Upper setpoint limit.
Range: 2~37°C (36~99°F)
07 ■ ■ FP-SP 5°C/
41°F
Frost protection setpoint.
Step: 0.5°C (1°F)
Range: 0~20°C (32-68°F)
08 ■ECM-MIN-V 3 V
ECM Min voltage.
Min voltage below which the fan output is 0%.
Step: 0.5 V
Range: 0~10 V
09 ■ECM-MAX-V 10 V
ECM Max voltage.
Max voltage below which the fan output is 100%.
Step: 0.5 V
Range: 0~10 V
10 ■ ■ STG-DFFR 3°C/
5°F
floor heater Stage temperature difference
Step: 0.5°C (1°F)
Range: 0~10°C (0-18°F)
11 ■ ■ HTRSS 1°C/2°F Hysteresis for ON/OFF control
Range: 1~5°C (2-9°F)
12 ■ ■ BI-FUNCTION 02
00: Occupancy Input
01: Dew Point Risk Input
02: Filter Alarm Input
03: Change Over Sensor Input
04: Warning
13 ■ ■ MODE-RST 00
00: No restriction
01: Cooling only
02: Heating only
14 ■ ■ FAN-RST 03
00: No Fan
01: One Speed Fan
02: Two Speed Fan
03: Three Speed Fan
15 ■ ■ FAN-DB 01
Fan operation in deadband:
00: OFF
01: Low
16 ■ ■ UNOCC-FAN 00
Fan mode in Unoccupied:
00: OFF
01: Low
...Continued...
SERVICE SETTING

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
English
PARAMETER SETTING (PART 2/2)
Code
T9200-
TB21-1JS0
T9200-
TF20-1JS0 Parameter name Default Function
17 ■■HTG-STG 02
00: One Heating Stage - Fan Coil
01: One Heating Stage - Floor Heating
02: Two heating stage
18 ■ ■ BI-PLRT 01
BI polarity:
00: Normally Close
01: Normally Open
19 ■ ■ OCC-OVRD 00
Override the OCC-S value:
00: No Override
01: Occupied
02: Unoccupied
21 ■ ■ FAN-DELAY 00 Fan off delay after valve closed, in seconds (0-99 s)
22 ■ECM-RLY 00 00: Disable
01: Enable
Note
• Terminal blocks changes depending on the application selected, please check the table beside rst
• The relay output are line voltage, they are connected with Terminal “L” internally
• The digital input “OCC” can assume di󰀨erent meaning depending on parameter 12 setting
ALARM CODE DESCRIPTION
Item Code Description
1 E1 Internal sensor warning.
2 HI High temperature warning. Room temperature >55°C (>131°F)
3 LO Low temperature warning. Room temperature <0°C (<32°F) or internal sensor opened.
4 E5 Dew point risk warning. Valves and fan are shut off when error is active.
8 E6 Filter alarm
9 E7 BI warning

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
中文
安装指导
请在安装前仔细阅读该安装指导和安全警告
维修和替换：
不要试图现场维修T9000系列温控器。如果T9000不能正常工作，请与附近江森自控办事处联系。当联系办事处更换产品的时
候，请说明外部标签或参数表上印有的类型/型号。
重要：
•T9000系列温控器仅用作设备控制。当T9000系列温控器调节装置失灵或故障时可能会导致人员伤害，财产损失及其他设备损坏。请在系统中增
加预防措施，如使用监控及报警系统、保护开关等，来加强此温度调节装置的机能失效和故障时的保护。
•不要把T9000装在结露、潮湿或有湿气处。湿气会损坏温控器。
•不要拆卸外壳中的PCB，拆卸PCB板将不再享有质保服务。
•使所有接线符合国家、地区和当地的规定。不要超过T9000系列温控器电气参数。
•使用前请移除LCD塑料保护壳。
警告：
在进行电器接线时确保电源断开。在带电时连接各部件可能引起电击，从而导致人员受伤甚至死亡。
•电击危险：按照国家、地区和当地的规定给温控器接地。接地失效可能导致电击和人员受伤甚至死亡。
•电击危险和财产损失：在温控器通电前把未使用的线头保护好，使之绝缘。任何一个未使用的线头未被绝缘和保护可能导致财产损失，电击和
人员受伤甚至死亡。
M
编号 功能
A开关键
B模式键
C功能键
D风速键
E上下调节键
T9200 界面
编号 功能
A制冷
B制热
C通风
D自动模式
E自动风速
F风速高中低
GTio2/ESP
H地暖
I占用模式
J警告
K键盘锁
L阀状态
M外置传感器
N压缩机保护中
O延时
P温度/湿度读数
Q低温保护
R除湿

T9200
P/N 24-11446-00018 Rev. B Issue Date: 11 2020
用户设置
关机状态下同时按 和 键5秒进入用户设置页面，参数设定列表按M或 切换参数，按键∧和∨键调整参数。
编号 T9200-TB21-1JS0 T9200-TF20-1JS0 参数名 默认值 功能含义
04 ■ ■ 静音 00 00:禁用;01:启用
05 ■ ■ 温度偏移 0°C/
0°F
阶跃:0.5°C (1°F)”
设定范围:-5°C~5°C(-9°F ~9°F)
06 ■ ■ 无人状态制冷设定值 26°C/
79°F
设置每步:0.5°C (1°F)”
设定范围:22~32°C (72-90°F)
07 ■ ■ 无人状态制热设定值 18°C/
64°F
阶跃:0.5°C (1°F)”
设定范围:10~21°C (50-70°F)
08 ■采样时间 10s 设定范围:1~99s
09 ■PB 5 设定范围:1~10
10 ■KI 10 设定范围:0~99
11 ■ ■ 背光时间 30 设定范围:5~99s
12 ■ ■ 断电重启 02
00:关闭
01:启动
02:恢复
13 ■ ■ TiO2/ESP操作 00 00:与风机联动
01:单独操作（通用键）
16 ■ ■ 按键锁 00
00:禁用
01:锁定所有按键
02:除风速及温度调节按键，锁定其他按键
03:锁定开关及通用按键
04:除开关键，锁定其他按键
17 ■ ■ 默认显示 00 00:室内温度
01:温度设定值
18 ■ ■ 温度单位 00 00:摄氏度(°C)
01:华氏度(°F)
20 ■ ■ 软件版本 只读
使用说明
开关机设置：按 键一次开机；再按一次关机，同时关闭风机盘管、电动阀。
模式调节：开机状态下，按M键进行工作模式切换。液晶显示 表示制冷，显示 表示制热，显示 表示通风, 表
示自动转换制冷制热模式（仅4管制FCU，或2管制FCU，BI输入功能设置为制冷制热模式转换）。
温度设置：在开机状态下，按 或 可进行设置温度的调节，每按一次，温度变化0.5℃/1°F。
风速调节：温控器有4种风机速度，自动 闪烁、高 、中 、低 风速。按 按钮，将循环切换。
注意：地暖模式下，地暖模式-风机设置成启用，风机才可以打开，仅单地暖模式下。
定时开关机设置：开机状态下，按 键，直至出现“on”符号，再次按 键以切换设置“On”延时开或者“Off”延时开
时间，按 或 键调整，每按一次变化30分钟。
注意：设定一次定时开关机时间只能执行一次，即只在一天内有效。
取消定时开关机设置：开机状态下，按 键，直至出现“on”符号，再次按 键以切换查看“On”延时开或者“Off”延
时开时间，按 或 键调整，每按一次变化30分钟，将时间调整为“00:00”，即为取消定时功能。
按键锁功能：如果温控器开启了 锁按键功能，在没有人使用的情况下30秒后会自动把按键锁上，禁止其他人员对温控器进
行操作。
按键解锁：按风速按键 5秒即可解锁（在没有人使用的情况下30秒后会自动把按键锁上）。
Tio2/ESP功能：仅在Tio2/ESP应用，且Tio2/ESP操作设定为手动操作,按 键马上释放以切换Tio2/ESP启用/停止。
中文