Johnson Controls T9600 User manual

T9600
LCD Digital Thermostat
Installation Guide
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
Building Efciency
Headquarters: Milwaukee, Wisconsin, USA
Branch Officies: Principal Cities World-wide
Johnson Controls®are registered trademarks of Johnson Controls.
All other marks herein are the marks of their respective owners.
© Copyright 2020 Johnson Controls. All rights reserved. Any unauthorized use or copying is strictly prohibited.
www.johnsoncontrols.com
*241144700004B*
87.77
87.77 60.00
13.83
45.83
> 50 cm
> 150 cm
°C
ON / OFF
AUTO
°C/°F
1s
TiO2/ESP
3s Timer
Symbol
ON OFF
ON OFF
• Ambient
• 工作环境
MAX
40 °C
104 °F
MIN
0 °C
-32 °F
MAX
60 °C
140 °F
MIN
-10 °C
-14 °F
MAX 90% RH
MIN 10% RH
 

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
T9600-TF20-1JS0
GND
MODBUS
NTC OCC
L
N
L
B ACOM
N
100-240 VAC 50/60Hz
V1
LowHi Med
FAN
2-pipe FCU (relay)
2管制开关阀
Cool/
Heat
V2
L
N
LN
100-240 VAC 50/60Hz
V2
COOL HEAT
GND
MODBUS
NTC OCC B ACOM
V1
LowHi Med
FAN
4-pipe FCU (relay)
4管制开关阀
L
N
LN
100-240 VAC 50/60Hz
ON OFF
GND
MODBUS
NTC OCC B ACOM
V2
V1
LowHi Med
FAN
2-pipe, 3 wire (relay)
2管制3线开关阀
L
N
LN
100-240 VAC 50/60Hz
TiO2
ESP
GND
MODBUS
NTC OCC B ACOM
V2
V1
LowHi Med
FAN
2-pipe FCU (relay)
with TiO2/ESP
2管制开关阀+TiO2/ESP
Cool/
Heat
L
N
LN
100-240 VAC 50/60Hz
FLOOR
HEAT
GND
MODBUS
NTC OCC B ACOM
V2
V1
LowHi Med
FAN
2-pipe FCU (relay)
with floor heating
2管制开关阀+地暖
Cool/
Heat
L
N
LN
100-240 VAC 50/60Hz
RV = REVERSING VALVE CMP = COMPRESSOR
CMP RV
GND
MODBUS
NTC OCC B ACOM
V2
V1
LowHi Med
FAN
Water source heat pump
水源热泵
T9603-T000-1JF0
NTC OCC COM
L
N
L
B AGND
N
100-240 VAC 50/60Hz
V1
HEAT
MODBUS
Single stage heater
单级制热
English 中文

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
T9600-TF21-1JS0
GND NTC OCC COM
FAN
L
N
LHI MED
B A
AO1 GND
0-10 VDC
NLOW
TR
24 VAC COM
100-240 VAC 50/60Hz
M
MODBUS
2-pipe FCU (prop) 3 speed fan
2管制比例阀，三速风机
GND NTC OCC COM
FAN
L
N
LHI MED
B A
AO1 GND
0-10 VDC
NLOW
TR
24 VAC COM
100-240 VAC 50/60Hz
M
MODBUS
AO2
M
HEAT
COOL
4-pipe FCU (prop) 3 speed fan
4管制比例阀，三速风机
T9601-TF20-1JS0
2-pipe FCU (relay) with ECM Fan
2管制开关阀，三速风机
GND
MODBUS
NTC OCC COM
L
N
L
F-ON
B A
GND
0-10 V
N
100-240 VAC 50/60Hz
ECM
FAN
FAN
V1
Cool/
Heat
V3 V2
4-pipe FCU (relay) with ECM Fan
4管制开关阀，ECM风机
GND
MODBUS
NTC OCC COM
L
N
L
F-ON
B A
GND
N
100-240 VAC 50/60Hz
FAN
V1V2
C OOL
HEAT
0-10 V
ECM
FAN
V3
2-pipe 3 wire (relay) with ECM fan
2管制三线阀，ECM风机
GND NTC OCC COM
L
N
L
F-ON
B AGND
N
100-240 VAC 50/60Hz
FAN
V1
V2
ONOFF
0-10 V
ECM
FAN MODBUS
V3
GND NTC OCC COM
L
N
L
F-ON
B A
GND
N
100-240 VAC 50/60Hz
FAN
V1V2
TiO2
ESP
0-10 V
ECM
FAN MODBUS
2-pipe ON/OFF with TiO2/ESP
and ECM fan
2管制开关阀+ TiO2/ESP,
ECM风机
Cool/
Heat
V3
GND NTC OCC COM
L
N
L
F-ON
B A
GND
N
100-240 VAC 50/60Hz
FAN
V1
V2
FLOOR
HEAT
0-10 V
ECM
FAN MODBUS
2-pipe FCU with floor heating
and ECM fan
2管制开关阀带地暖，ECM风机
V3
Cool/
Heat
GND NTC OCC COM
L
N
L
F-ON
B A
GND
N
100-240 VAC 50/60Hz
FAN
V1V2
RV = REVERSING VALVE CMP = COMPRESSOR
CMP
RV
0-10 V
ECM
FAN MODBUS
Water source heat pump
with ECM fan
水源热泵, ECM风机
V3
English 中文

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
T9601-TF20-1JS0
2-pipe FCU (prop) with ECM Fan
2管制调节阀，ECM风机
GND
MODBUS
NTC OCC COM
L
N
F-ON
B AGND
100-240 VAC 50/60Hz
ECM
FAN
FAN AO1
M
LN
V3 V1V2
Cool/
Heat
2-pipe FCU (prop)
with floor heating
2管制调节阀带地暖，ECM风机
GND
MODBUS
NTC OCC COM
L
N
F-ON
B AGND
100-240 VAC 50/60Hz
ECM
FAN
FAN AO1
M
FLOOR
HEAT
LN
V1V2V3
Cool/
Heat
2-pipe FCU (prop) with radiator
and ECM fan
2管制调节阀+ 电加热, ECM风机
MODBUS
NTC OCC COM
L
N
F-ON
B AGND
100-240 VAC 50/60Hz
ECM
FAN
FAN AO1
M
HEAT
COOL
GND
L N
V1V2V3
AHU
空气处理机
MODBUS
NTC OCC COM
L
N
B AGND
100-240 VAC 50/60Hz
FAN
M
DAMPER FAN
GND
L N
V1V2V3
Cool/
Heat
English 中文
图例：
MODBUS：
A： MODBUSA线
B： MODBUSB线
COM： MODBUS公共端
NTC： 温度传感器
OCC： 门卡开关
ECMFAN： ECM风机
FAN： 风机
AO1： 模拟输出1
AO2： 模拟输出2
AI： 模拟输入/阀反馈
HEAT： 热水阀
COOL： 冷水阀
FLOORHEAT：地暖阀
LOW： 风机低速档位
MED： 风机中速档位
HI： 风机高速档位
TiO2： TiO2二氧化钛
ESP： Electro-staticPrecipitator静电除尘设备
CMP：Compressor压缩机
RV： ReversingValve换向阀
F-ON：风机开关
GND:地
L：火线
N：零线
V1：阀1
V2：阀2
TR：变压器

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
English
Callout Feature
ACooling
BHeating
CVentilation
DAuto mode
EFan auto
FFan speed Hi/Med/Low
GTio2/ESP
HFloor heating
IOccupancy
JAlarm
KLock
LValve status
MRemote sensor
NCommunication
OCompressor protection
PDelay time
QTemperature and humidity value
RLow temperature protection
SDehumidify
T9600 interface
INSTALLATION INSTRUCTIONS FOR THE TECHNICIAN / FITTER
READ THIS INSTRUCTION SHEET AND THE SAFETY WARNINGS CAREFULLY BEFORE INSTALLING AND
SAVE IT FOR FUTURE USE
REPAIR AND REPLACEMENT
Do not attempt to repair the T9 Series thermostat. In case of an improperly functioning control, contact the nearest Johnson Controls®representative, and
specify the desired product code number. When contacting the supplier for a replacement, state the type/model number of the control located on the data
plate or cover label.
IMPORTANT
• Use this T9 Series thermostat only as an operating control. Where failure or malfunction of the T9 Series thermostat could lead to personal injury or
property damage to the controlled equipment or other property, additional precautions must be designed into the system. Incorporate and maintain other
devices such as supervisory or alarm systems or safety or limit controls intended to warn of, or protect against, failure or malfunction of the T9 Series
thermostat.
• Do not install this thermostat in condensing, wet, or damp environments. Moisture may cause damage to the thermostat.
• Do not remove PCB from the enclosure cover. Removing the PCB from the enclosure cover voids the product warranty.
• Make all wiring connections in accordance with local, national, and regional regulations. Do not exceed the T9 Series thermostat’s electrical ratings.
WARNING
Disconnect power supply before making electrical connections. Contact with components carrying hazardous voltages can cause electrical shock and may
result in severe personal injury or death.
• Risk of Electrical Shock: Ground the thermostat according to local, national, and regional regulations. Failure to ground the thermostat may result in
electrical shock and severe personal injury and death.
• Risk of Electrical Shock and Property Damage: Insulate and secure each unused wire lead before applying power to the thermostat.
Failure to insulate and secure each unused wire lead may result property damage, electrical shock, and severe personal injury or death.
M
Callout Feature
APower button
BWorking mode button
CGeneral button
DFan speed adjustment button
EUp and down buttons

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
English
USER SETTING
Press and button for 5 seconds at power off mode to get in parameter list. Press to scroll forward and Mbutton to scroll backward in
the list and use and button to change parameter value. For T9603-T000-1JF0, press and hold for 3 seconds to access the parameter
list and press to scroll foward through the list.
PARAMETER SETTING (PART 1/2)
Code
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 Parameter name Default Function
02 ■ ■ ■ ■ MAC (Modbus) 01 Mac address for Modbus
1-96
04 ■ ■ ■ ■ MUTE 00
Enable/disable the beep when push touch button:
00: Disable
01: Enable
05 ■ ■ ■ ■ OFFSET 0°C/
0°F
Offset to be compensate the room temperature:
Step: 0.5°C (1°F)”
Range: 5°C~-5°C (9°F- -9°F)
06 ■ ■ ■ UNOCC-CLG-SP 26°C/
79°F
Cooling setpoint unoccupied mode.
Not available for Boiler application
Step: 0.5°C (1°F)
Range: 22°C~32°C (72°F-90°F)
07 ■ ■ ■ ■ UNOCC-HTG-SP 18°C/
64°F
Heating setpoint unoccupied mode.
Step: 0.5°C (1°F)
Range: 10°C~21°C (50°F-70°F)
08 ■ ■ SMPL-TM 10 s
Sample time,
PID parameter, only for PID
Range: 1~99 s
09 ■ ■ PB 5
Proportion band,
PID parameter, only for PID
Range: 1~10
10 ■ ■ KI 10
Integration parameter,
PID parameter, only for PID
Range: 0~99
11 ■ ■ ■ ■ BL-TIMER 30 Backlight timer.
Range: 0~99 s
12 ■ ■ ■ ■ PWR-F-RSTT 02
Restart after power failure:
00: OFF
01: ON
02: Recovery
13 ■ ■ TIO2ESP-CTL 00
TIO2ESP control:
00: Automatic
01: Manual
For TIO2ESP application
15 ■ ■ ■ ■ BAUD_MODBUS 00
Baud rate for Modbus:
00: 9600
01: 4800
...Continued...
INSTRUCTIONS
On/Off Setting: Press to turn on, press again to turn off, close the fan and valve.
Mode Selection: Press Mto change the working mode, for cooling, for heating, for venting, for auto cooling or
heating mode. is available only for 4-pipe application or 2-pipe application when BI-FUNCTION is Change Over Sensor
input.
Temperature Setting: Press either or button to increase or decrease the temperature by 0.5°C/1°F.
Fan Speed Adjustment: Press to switch the fan mode, auto ash, high , medium , low fan.
Note: Fan stops at Floor Heating Mode, until FH-FAN parameter set to enable, for single stage oor heating application only.
Delay On/Off setup: Press and hold button 5 seconds, then “ON” appears, press button to switch On or Off delay,
then press or to adjust the minute by 30 minutes.
Note: Time-On/Off setting performs only once within one day.
Delay On/Off Cancel: Press and hold button 5 seconds, then “ON” appears, press button to switch to check On or Off
delay time, then press or adjust the time to “00:00”.
Lock setup: If Lock function is enabled, the thermostat locks automatically after 30 seconds unused.
Unlock function: Press and hold the button 5 seconds to unlock. T9603-T000-1JF0 has no button, press and hold the
button 5 seconds to unlock instead.
Tio2/ESP Manual: When Tio2/ESP function is set to Manual, press button once, to switch Tio2/ESP On or Off.

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
English
PARAMETER SETTING (PART 2/2)
Code
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 Parameter Name Default Function
16 ■ ■ ■ ■ KEY-LOCK 00
Key lock function:
00: No Lockout
01: Level 1 ->Lock all keys
02: Level 2 ->Lock the keys except Fan Speed and Temp
Adjustment keys
03: Level 3 ->Lock the ON/OFF and Clock keys
04: Level 4 ->Lock the keys except ON/OFF key
17 ■ ■ ■ ■ TEMP-DISP 00
UI display room temperature or set point:
00: Room Temperature
01: Setpoint
18 ■ ■ ■ ■ UNIT 01
Unit selection:
00: IP
01: SI
19 ■DAMP-OPEN-TIME 0 Damper opening time, for AHU application
range 0-99 (0=75 s, 99=174 s)
20 ■ ■ ■ ■ SF-VERSION Software version, read only
SERVICE SETTING (Setting through professional)
In the Setting page press button for 3 seconds to get in Service page, the occupancy icon shows. Press to scroll forward and Mbutton to
scroll backward in the list and use and button to change parameter value. For T9603-T000-1JF0, press and hold for 3 seconds to access
the parameter list and press to scroll foward through the list.
PARAMETER SETTING (PART 1/2)
Code
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 Parameter name Default Function
02 ■ ■ ■ ■ FRST-PRT 00
Frost protection:
00: No
01: Yes
03 ■ ■ FH-FAN 00
Enable/disable fan output when floor heater
00: Disable
01: Enable
04 ■ ■ ■ APPLICATION 00
T9600- TF20-1JS0:
00: 2pipe FCU (relay)
01: 4pipe FCU (relay)
02: 2pipe 3 wire (relay)
03: 2pipe FCU (relay) with floor heating
04: 2pipe FCU (relay) with TiO2/ESP
05: water source heat pump
T9601- TF20-1JS0:
00: 2-pipe FCU (relay), ECM fan
01: 4-pipe FCU (relay), ECM fan
02: 2-pipe 3 wire (relay), ECM fan
03: 2-pipe FCU with floor heater, ECM fan
04: 2-pipe FCU with TiO2/ESP, ECM fan
05: water source heat pump, ECM fan
06: 2-pipe FCU (prop), ECM fan
07: 2-pipe FCU (prop) with floor heater, ECM fan
08: 2-pipe FCU (prop) with radiator, ECM fan
09. AHU
T9600- TF21-1JS0:
00: 2-pipe FCU, three speed fan
01: 4-pipe FCU, three speed fan
05 ■ ■ ■ ■ DOWN-SET-LIMIT 5°C/
41°F
lower setpoint limit
Range: 0°C~36°C (32°F-97°F)
06 ■ ■ ■ ■ UP-SET-LIMIT 35°C/
95°F
Upper setpoint limit
Range: 2°C~37°C (36°F~99°F)
07 ■ ■ ■ ■ FP-SP 5°C/
41°F
Frost protection setpoint.
Step: 0.5°C (1°F)
Range: 0°C~20°C (32°F-68°F)
08 ■ECM-MIN-V 3 V
ECM Min voltage.
Min voltage below which the fan output is 0%.
Step: 0.5 V
Range: 0 V~10 V
...Continued...

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
Note
• Terminal blocks changes depending on the application selected, check the table beside rst
• The relay output are line voltage, they are connected with Terminal “L” internally
• The digital input “OCC” can assume different meaning depending on parameter 12 setting
• The T9603-T000-1JF0 does not feature the and Mbutton. To access the User Setting parameter list, press the button 5 s instead. Press the
button to scroll through the list. Under User Setting menu, press the button 5 s to access Service Setting parameter list. Press the button to scroll
through the list.
1.T9603-T000-1JF0 BI Input default 04 Warning. Options: 00: Occupancy Input, 04: Warning
PARAMETER SETTING (PART 2/2)
Code
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 Parameter Name Default Function
09 ■ECM-MAX-V 10 V
ECM Max voltage.
Max voltage below which the fan output is 100%.
Step: 0.5 V
Range: 0 V~10 V
10 ■ ■ STG-DFFR 3°C/5°F
floor heater Stage temperature difference
Step: 0.5°C (1°F)
Range: 0°C~10°C (0°F-18°F)
11 ■ ■ ■ ■ HTRSS 1°C/2°F Hysteresis for ON/OFF control
Range: 1~5
12 ■ ■1■ ■ BI-FUNCTION 02
00: Occupancy Input
01: Dew Point Risk Input
02: Filter Alarm Input
03: Change Over Sensor Input
04: Warning
13 ■ ■ ■ MODE-RST 00
00: No Restriction
01: Cooling only
02: Heating only
14 ■ ■ ■ FAN-RST 03
00: No Fan
01: One Speed Fan
02: Two Speed Fan
03: Three Speed Fan
15 ■ ■ ■ FAN-DB 01
Fan operation in deadband:
00: OFF
01: Low
16 ■ ■ ■ UNOCC-FAN 00
Fan mode in unoccupied:
00: OFF
01: Low
17 ■ ■ HTG-STG 02
00: One Heating Stage - Fan Coil
01: One Heating Stage - Floor Heating
02: Two heating stage
18 ■ ■ ■ ■ BI-PLRT 01
BI polarity:
00: Normally Close
01: Normally Open
19 ■ ■ ■ ■ OCC-OVRD 00
Override the OCC-S value:
00: No Override
01: Occupied
02: Unoccupied
20 ■ ■ ■ ■ SNS-TYPE 00 00: JCI type 10K NTC
01: China type 10K NTC
21 ■ ■ ■ FAN-DELAY 00 Fan off delay after valve closed, in seconds(0-99 s)
22 ■ECM-RLY 00 00: Disable
01: Enable
English
ALARM CODE DESCRIPTION
Item Code Description
1 E1 Internal sensor warning.
2 HI High temperature warning. Room temperature >55°C (>131°F)
3 LO Low temperature warning. Room temperature <0°C (<32°F) or internal sensor opened.
4 E5 Dew point risk warning. Valves and fan are shut off when error is active.
8 E6 Filter alarm
9 E7 BI warning
ashes when there is a communication error.

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
安装指导
请在安装前仔细阅读该安装指导和安全警告
维修和替换：
不要试图现场维修T9000系列温控器。如果T9000不能正常工作，请与附近江森自控办事处联系。当联系办事处更换产品的时
候，请说明外部标签或参数表上印有的类型/型号。
重要：
•T9000系列温控器仅用作设备控制。当T9000系列温控器调节装置失灵或故障时可能会导致人员伤害，财产损失及其他设备损坏。请在系统中增
加预防措施，如使用监控及报警系统、保护开关等，来加强此温度调节装置的机能失效和故障时的保护。
•不要把T9000装在结露、潮湿或有湿气处。湿气会损坏温控器。
•不要拆卸外壳中的PCB，拆卸PCB板将不再享有质保服务。
•使所有接线符合国家、地区和当地的规定。不要超过T9000系列温控器电气参数。
•使用前请移除LCD塑料保护壳。
警告：
在进行电器接线时确保电源断开。在带电时连接各部件可能引起电击，从而导致人员受伤甚至死亡。
•电击危险：按照国家、地区和当地的规定给温控器接地。接地失效可能导致电击和人员受伤甚至死亡。
•电击危险和财产损失：在温控器通电前把未使用的线头保护好，使之绝缘。任何一个未使用的线头未被绝缘和保护可能导致财产损失，电击和
人员受伤甚至死亡。
中文
M
编号 功能
A开关键
B模式键
C功能键
D风速键
E上下调节键
编号 功能
A制冷
B制热
C通风
D自动模式
E自动风速
F风速高中低
GTio2/ESP
H地暖
I占用模式
J警告
K键盘锁
L阀状态
M外置传感器
N通讯
O压缩机保护中
P延时
Q温度/湿度读数
R低温保护
S除湿
T9600 界面

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
用户设置
关机状态下同时按 和 键5秒进入用户设置页面，参数设定列表按M或 切换参数，按键∧和∨键调整参数。对于
T9603-T000-1JF0，按住 3秒钟以访问参数列表，然后按 向前滚动列表。
编号
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 参数名 默认值 功能含义
02 ■ ■ ■ ■ Modbus地址 01 1-96
04 ■ ■ ■ ■ 静音 00 00:禁用
01:启用
05 ■ ■ ■ ■ 温度偏移 0°C/
0°F
阶跃:0.5°C (1°F)”
设定范围:5°C~5°C (-9°F~9°F)
06 ■ ■ ■ 无人状态制冷设定值 26°C/
79°F
设置每步:0.5°C (1°F)”
设定范围:22°C~32°C (72°F-90°F)
07 ■ ■ ■ ■ 无人状态制热设定值 18°C/
64°F
阶跃:0.5°C (1°F)”
设定范围:10°C~21°C (50°F-70°F)
08 ■ ■ 采样时间 10 s 设定范围:1~99s
09 ■ ■ PB 5设定范围:1~10
10 ■ ■ KI 10 设定范围:0~99
11 ■ ■ ■ ■ 背光时间 30 设定范围:0~99s
12 ■ ■ ■ ■ 断电重启 02
00:关闭
01:启动
02:恢复
13 ■ ■ TiO2/ESP操作 00 00:与风机联动
01:单独操作（通用键）
15 ■ ■ ■ ■ 波特率 00 00:9600
01:4800
16 ■ ■ ■ ■ 按键锁 00
00:禁用
01:锁定所有按键
02:除风速及温度调节按键，锁定其他按键
03:锁定开关及通用按键
04:除开关键，锁定其他按键
17 ■ ■ ■ ■ 默认显示 00 00:室内温度
01:温度设定值
18 ■ ■ ■ ■ 温度单位 00 00:摄氏度(°C)
01:华氏度(°F)
...继续...
使用说明
开关机设置：按 键一次开机；再按一次关机，同时关闭风机盘管、电动阀。
模式调节：开机状态下，按M键进行工作模式切换。液晶显示 表示制冷，显示 表示制热，显示 表示通风, 表
示自动转换制冷制热模式（仅4管制FCU，或2管制FCU，BI输入功能设置为制冷制热模式转换）。
温度设置：在开机状态下，按 或 可进行设置温度的调节，每按一次，温度变化0.5℃/1°F。
风速调节：温控器有4种风机速度，自动 闪烁、高 、中 、低 风速。按 按钮，将循环切换。
注意：地暖模式下，地暖模式-风机设置成启用，风机才可以打开，仅单地暖模式下。
定时开关机设置：开机状态下，按 键，直至出现“on”符号，再次按 键以切换设置“On”延时开或者“Off”延时开
时间，按 或 键调整，每按一次变化30分钟。
注意：设定一次定时开关机时间只能执行一次，即只在一天内有效。
取消定时开关机设置：开机状态下，按 键，直至出现“on”符号，再次按 键以切换查看“On”延时开或者“Off”延
时开时间，按 或 键调整，每按一次变化30分钟，将时间调整为“00:00”，即为取消定时功能。
按键锁功能：如果温控器开启了 锁按键功能，在没有人使用的情况下30秒后会自动把按键锁上，禁止其他人员对温控器进
行操作。
按键解锁：按风速按键 5秒即可解锁（在没有人使用的情况下30秒后会自动把按键锁上）。T9603-T000-1JF0没有风速键
，按 键5秒解锁。
Tio2/ESP功能：仅在Tio2/ESP应用，且Tio2/ESP操作设定为手动操作,按 键马上释放以切换Tio2/ESP启用/停止。
中文

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
高级设置 (专业人员设置)
在用户设置页面下按 和3秒进入高级设置页面，此时有人模式图标 显示。参数设定列表按M键切换参数，按键∧和
∨键调整参数。对于T9603-T000-1JF0，按住 3秒钟以访问参数列表，然后按 向前滚动列表。
编号
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 参数名 默认值 功能含义
02 ■ ■ ■ ■ 低温保护 00 00:关闭
01:开启
03 ■ ■ 地暖模式-风机 00
地暖模式下，是否允许启用风机:
00:否
01:是
04 ■ ■ ■ 应用 00
T9600-TF20-1JS0
00:2管制开关阀
01:4管制开关阀
02:2管制3线开关阀
03:2管制开关阀+地暖
04:2管制开关阀+TiO2/ESP
05:水源热泵
T9601-TF20-1JS0
00:2管制开关阀，ECM风机
01:4管制开关阀，ECM风机
02:2管制三线阀，ECM风机
03:2管制开关阀带地暖，ECM风机
04:2管制开关阀+TiO2/ESP,ECM风机
05:水源热泵,ECM风机
06:2管制调节阀，ECM风机
07:2管制调节阀带地暖，ECM风机
08:2管制调节阀+电加热,ECM风机
09:空气处理机
T9600-TF21-1JS0
00:2管制调节阀,三速风机
01:4管制调节阀,三速风机
05 ■ ■ ■ ■ 设定值下限 5°C/
41°F 设定范围0°C~36°C (32°F-97°F)
06 ■ ■ ■ ■ 设定值上限 35°C/
95°F 设定范围2°C~37°C (36°F-99°F)
07 ■ ■ ■ ■ 低温保护设定值 5°C/
41°F 设定范围0°C~20°C (32°F-68°F)
08 ■ECM风机电压输入下限 3 V 0%对应电压值，设定范围0V-10V.（0.5V阶跃）
09 ■ECM风机电压输入上限 10 V 100%对应电压值，设定范围0V-10V.（0.5V阶跃）
10 ■ ■ 制热阶段切换阈值 3°C/
5°F 设定范围0°C~10°C (0°F-18°F)
11 ■ ■ ■ ■ 温度回差 1°C/
2°F 设定范围:0°C~5°C
12 ■ ■1■ ■ BI输入 02
00:无人模式
01:露点报警
02:滤网报警
03:制冷制热模式转换
04:报警
13 ■ ■ ■ 模式限制 00
00:制冷/制热/通风
01:单冷
02:单热
...继续...
中文
用户设置
编号
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 参数名 默认值 功能含义
19 ■阀门开启时间 0仅AHU应用
0-99(0=75s99=174s)
20 ■ ■ ■ ■ 软件版本 只读，不可设置，显示当前软件版本号

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
注意：
•接线前请查看接线图中的应用表以确定端子接线方式
•温控器继电器输出为线电压，内部继电器与火线相连
•参数12可配置BI输入“OCC”为不同应用
•T9603-T000-1JF0没有风速 和模式M按键,按通用按键 5秒进入用户设置页面，按通用按键 切换参数；在用户设置页面，再按通用键
5秒进入高级设置页面，按通用按键 切换参数
1. T9603-T000-1JF0BI输入默认为04报警，选项有00:无人模式；04:报警
产品中有害物质的名称及含量
部件名称
有害物质
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
塑胶部件 O O O O O O
电路板及组件 O O O O O O
金属部件 O O O O O O
本表格依据SJ/T11364的规定编制
○：表示该有害物质在该部件所有均质材料中的含量均在GB/T26572规定的限量要求以下
×：表示该有害物质在该部件所有均质材料中的含量超出GB/T26572规定的限量要求
（产品中使用的物料超出SJ/T11364标准，但在欧盟RoHS中，此项为豁免，因目前技术无法有符合SJ/T11364的替代材料）
报警代码描述
编号 代码 描述
1 E1 内置温度传感器故障
2 HI 高温报警，室内温度>55℃.
3 LO 1)低温报警，室内温度<0℃.
2)传感器开路
4 E5 露点传感器报警
8 E6 滤网报警
9 E7 BI报警
图标闪烁表示通讯故障报警
中文
高级设置 (专业人员设置)
编号
T9600-
TF20-
1JS0
T9603-
T000-
1JF0
T9601-
TF20-
1JS0
T9600-
TF21-
1JS0 参数名 默认值 功能含义
14 ■ ■ ■ 风速限制 03
00:风扇禁用
01:单风速（接LOW）
02:两风速（接MED，LOW）
03:三风速
15 ■ ■ ■ 死区风机状态 01 00:关闭
01:低风速
16 ■ ■ ■ 无人模式风机状态 00 00:关闭
01:低风速
17 ■ ■ 制热阶段 02
00:单级制热-风机盘管
01:单级制热-地暖
02:两级制热
18 ■ ■ ■ ■ BI输入正反属性 01 00:常闭
01:常开
19 ■ ■ ■ ■ 强制占用模式 00
00：无强制
01：强制占用
02：强制非占用
20 ■ ■ ■ ■ 传感器类型 00 00:JCI版10kNTC
01:中国版10KNTC
21 ■ ■ ■ 风机延时 00 阀关闭后,风机延时关时间(0-99s)
22 ■ECM启停 00 00:禁用
01:启用

T9600
P/N 24-11447-00004 Rev. B Issue Date: 11 2020
European Single Point of Contact:
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
NA/SA Single Point of Contact:
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
APAC Single Point of Contact:
JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142 - CHINA
Use of the software that is in (or constitutes) this product,or access to the cloud, or hosted services applicable to this
product, if any, is subject to applicable terms set forth at www.johnsoncontrols.com/techterms. Your use of this product
constitutes an agreement to such terms.
This product is covered by a limited warranty, details of which can be found at www.johnsoncontrols.com/
buildingswarranty.
Software terms
Product warranty
Compliance Johnson Controls declares that these products are in compliance with the essential requirements and other relevant
provisions of the EMC Directive and Low Voltage Directive.
English