Johnson Controls TEC2045-4 User manual

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-
Speed Fan Control Installation Instructions 1
Application
The TEC Series Wireless Thermostat Controller
System provides wireless networked control of
Heating, Ventilating, and Air Conditioning (HVAC)
equipment on a Building Automation System (BAS)
that enables remotemonitoring and programming. This
TEC Series System integrates into a supervisory
controller that uses BACnet® Internet Protocol (IP) or
BACnet Master-Slave/Token-Passing (MS/TP)
communications.
TEC20 Coordinators allow the supervisory controller to
communicate with multiple TEC Wireless Thermostat
Controllers. TEC2045-4 Wireless Thermostat
Controllers control two-pipe fan coils, cabinet unit
heaters, or other equipment using a proportional
0 to 10 VDC control input and one-speed fan control.
The wireless mesh network uses ZigBee™ technology
to enable remote monitoring and programming and to
enhance reliability by providing redundant transmission
paths through other TEC Wireless Thermostat
Controllers, creating a resilient, self-healing mesh
network.
North American Emissions Compliance
United States
Canada
IMPORTANT: The TEC2045-4 Wireless
Thermostat Controller is intended to provide an input
to equipment under normal operating conditions.
Where failure or malfunction of the thermostat
controller could lead to personal injury or property
damage to the controlled equipment or other
property, additional precautions must be designed
into the control system. Incorporate and maintain
other devices, such as supervisory or alarm systems
or safety or limit controls, intended to warn of or
protect against failure or malfunction of the
thermostat controller.
This equipment has been tested and found to comply with
the limits for a Class A digital device pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
this equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be
required to correct the interference at his/her own
expense.
RF Transmitters: Compliance Statement (Part 15.19)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This Class (A) digital apparatus meets all the requirements
of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la Classe (A) respecte toutes
les exigences du Règlement sur le matériel brouilleur du
Canada.
RF Transmitters: Industry Canada Statement
The term IC before the certification/registration number
only signifies that the Industry Canada technical
specifications were met.
Le terme « IC » précédant le numéro d'accréditation/
inscription signifie simplement que le produit est conforme
aux spécifications techniques d'Industrie Canada.
TEC2045-4 Wireless Thermostat Controller with Single
Proportional Output and One-Speed Fan Control
Installation Instructions
TEC2045-4
Part No. 24-9890-1109, Rev. B
Issued July 13, 2010
Supersedes May 17, 2010

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
2
Installation
Location Considerations
Locate a thermostat controller:
• on a partitioning wall, approximately 1.5 m (5 ft)
above the floor in a location of average
temperature
• away from direct sunlight, radiant heat, outside
walls, behind doors, air discharge grills, stairwells,
or outside doors
• away from steam or water pipes, warm air stacks,
unconditioned areas (not heated or cooled), or
sources of electrical interference
Note: Allow for vertical air circulation to the
TEC2045-4 Thermostat Controllers.
Wireless Signal Transmission Range
Line-of-sight transmission ranges between a
TEC20 Coordinator and a TEC Wireless Thermostat
Controller (or between TEC Wireless Thermostat
Controllers) can be less than the recommended
distances shown in Table 1. The effective transmission
range for indoor applications varies because of Radio
Frequency (RF) signal absorption and reflection due to
metal obstructions, walls (or floors), and furniture found
in typical building interiors.
For detailed information on locating devices for
optimum signal strength, refer to the Wireless Metasys
System Location Guide (LIT-12011294), which is
available on the Johnson Controls® Portal intranet site.
Installing the Thermostat Controller
Follow these steps to install the thermostat controller:
1. Use a Phillips-head screwdriver to remove the
security screw if it is installed on the bottom of the
thermostat controller cover.
Note: Normally, the security screw is packaged
separately in a plastic bag with the thermostat
controller. Skip this step if the screw is not installed
on the bottom of the cover.
2. Pull the bottom edge of the thermostat cover and
open the thermostat illustrated in Figure 1.
3. Carefully pull the locking tabs on the right side of
the mounting base and unlock the Printed Circuit
Board (PCB). Open the PCB to the left as
illustrated in Figure 2.
4. Pull approximately 152 mm (6 in.) of wire from the
wall, and insert the wire through the hole in the
mounting base.
5. Align the mounting base on the wall, and use the
base as a template to mark the two mounting hole
locations.
Note: If you need to install the thermostat on an
electrical junction box, use 2-1/2 x 4 in.
(63 x 101 mm) square boxes with mud ring covers,
and avoid smaller 1-1/2 x 4 in. (38 x 101 mm)
square or 3 x 2 in. (76 x 51 mm) boxes. This
procedure ensures you have enough space for
cabling and end-of-line devices, if needed.
Table 1: Recommended Transmission Ranges
Type Distance
Through Walls 10 m (32.8 ft)
Open Space 30 m (98.4 ft)
Figure 1: Removing the Cover
FIG:cvr_rmvl
Figure 2: Opening the PCB
FIG:prnt_circ_
brd
PCB
Locking
Tabs

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 3
Note: For surface-mount applications, use
durable mounting hardware such as Molly bolt
anchors that cannot be easily pulled out of the
mounting surface.
6. Position the thermostat mounting base on the wall
so that the arrow on the base points upward to
indicate the top of the thermostat.
7. Secure the mounting base to the wall surface using
two mounting screws as illustrated in Figure 3.
Note: Be careful not to overtighten the mounting
screws.
8. Swing the PCB back to the right, and carefully
snap it into the locking tabs on the mounting base.
9. Remove the screw terminal blocks that are
attached to a disposable adhesive. Figure 4
illustrates the locations of the screw terminal
blocks on the thermostat controller.
Wiring
When replacing an existing thermostat controller,
remove and label the wires to identify the terminal
functions. When replacing a thermostat controller of the
same model, simply remove the old screw terminal
blocks, and reinsert them onto the PCB of the
replacement thermostat controller.
To wire the thermostat controller:
1. Strip the ends of each wire 6 mm (1/4 in.), and
connect them to the appropriate screw terminals as
indicated in Figure 5.
2. Carefully push any excess wire back into the wall.
Note: Seal the hole in the wall with fireproof
material to prevent drafts from affecting the
ambient temperature readings.
3. Reinsert the screw terminal blocks onto the PCB.
Note: If multiple wires are inserted into the
terminals, be sure to properly twist the wires
together prior to inserting them into the terminal
connectors.
4. Reattach the cover to the mounting base (top side
first).
5. Use a Phillips-head screwdriver to reinstall the
security screw on the bottom of the cover.
See Figure 5, Figure 6, Figure 7, and Table 2 for
information on wiring the thermostat controllers.
Figure 3: Securing the
Mounting Base to the Wall
FIG:mntng_bs
Figure 4: Removing the Screw Terminal Blocks
FIG:trmnl_blcks
!
CAUTION: Risk of Electric Shock.
Disconnect the power supply before
making electrical connections to avoid
electric shock.
!
CAUTION: Risk of Property Damage.
Do not apply power to the system before
checking all wiring connections. Short
circuited or improperly connected wires
may result in permanent damage to the
equipment.
IMPORTANT: Make all wiring connections in
accordance with local, national, and regional
regulations. Do not exceed the electrical ratings of
the thermostat controller.

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
4
Figure 5: TEC2045-4 Thermostat Controller
Terminals
Fan
Three-Pole
Left Top Connector
Two-Pole
Right Top Connector
Six-Pole Bottom Connector
Blank
24 V~
Hot 24 V~
Com
BO5
Aux
BO5
Aux
Scom
AO1 UI3 BI1 BI2
34567
10 11 1
2
14 1
5
16
FIG:TEC2045_trmnls
Table 2: TEC2045-4 Thermostat Controller
Terminals
Terminal
Number Terminal Label Function
3Fan Fan On
424 V~ Hot 24 VAC from Transformer
524 V~ Com 24 VAC from Transformer
(Common)
6BO5 Aux Auxiliary Binary Output
7BO5 Aux Auxiliary Binary Output
10 AO1 Open Cool
11 Blank Close Cool
12 BI1 Configurable Binary Input 1
14 Scom Sensor Common
15 BI2 Configurable Binary Input 2
16 UI3 Configurable Universal Input 3
Figure 6: TEC2045-4 Thermostat Controller with Separate Power Source for Auxiliary Contact
FIG:TEC2045_diff
Separate 24 VAC
Power Source for Auxiliary Output
(24 VAC Maximum)
BO5
Aux
BO5
Aux
24 VAC
Thermostat Power
Fan
24 V~
Com
0 to 10 VDC
24 VAC
Com
Analog Output
and Valve
24 V~
Hot
AO1
Fan
Power and Fan
Aux Contact
(Isolated Common)
• Reheat
• Lighting
• On/Off Actuation
• Exhaust Fan
Aux
Load
BI2 UI3
BI1
Scom
- OR -
Remote Inputs
SS (Supply Sensor)
COS (Change Over Sensor)
Voltage-Free
Contact
• COC/NH
Normally Heat
Closed Contact
= Cold Water
• COC/NC
Normally Cool
Closed Contact
= Hot Water
Voltage-Free
Contact
• Door
• Remote
Override
• FilterAlarm
• Service Alarm
Voltage-Free
Contact
• Remote NSB
• Motion
• Window

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 5
Setup and Adjustments
Thermostat Controller User Interface Keys
The user interface consists of keys on the front cover
(Figure 8). The function of each key is as follows:
•MODE key toggles among the system modes
available, as defined by selecting the appropriate
operation sequence in the Installer Configuration
Menu (Off, Heat, Cool, Auto).
•FAN key toggles between ON and AUTO for fan
control. ON energizes the fan all the time and
AUTO operates the fan only on a call for heating or
cooling, for both occupied and unoccupied periods.
•OVERRIDE key overrides the unoccupied mode to
occupied at the local user interface for the
specified TOccTime. (TOccTime is defined by
selecting the appropriate time period in the Installer
Configuration Menu.) If one of the binary inputs is
configured to operate as a remote overridecontact,
this OVERRIDE function is disabled. The
OVERRIDE key also allows access to the Installer
Configuration Menu. See the Configuring the
Thermostat Controller section.
•UP/DOWN arrow keys change the configuration
parameters and activate a setpoint adjustment.
Figure 7: TEC2045-4 Thermostat Controller with Same Power Source for Auxiliary Contact
FIG:TEC2045_sme
Same 24 VAC
Power Source for Auxiliary Output
(24 VAC Maximum)
24 VAC
Thermostat Power
Fan
24 V~
Com
0 to 10 VDC
24 VAC
Com
Analog Output
and Valve
24 V~
Hot
AO1
Fan
Power and Fan
BO5
Aux
BO5
Aux
Aux Contact
(Isolated Common)
• Reheat
• Lighting
• On/Off Actuation
• Exhaust Fan
Aux
Load
BI2 UI3
BI1
Scom
- OR -
Remote Inputs
SS (Supply Sensor)
COS (Change Over Sensor)
Voltage-Free
Contact
• COC/NH
Normally Heat
Closed Contact
= Cold Water
• COC/NC
Normally Cool
Closed Contact
= Hot Water
Voltage-Free
Contact
• Door
• Remote
Override
• FilterAlarm
• Service Alarm
Voltage-Free
Contact
• Remote NSB
• Motion
• Window
Figure 8: Front Cover of TEC2045-4 Thermostat Controller
70.0ºF
Room Temp
FIG:TEC2045_wrlss_frntvw
Status LED beneath cover
indicates network status.
Five keys on the thermostat controller
make operation easy and intuitive.
Backlit, plain text
Liquid Crystal Display (LCD)
is easy to read in any condition.
Light-Emitting Diodes (LEDs)
indicate system activity.

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
6
Light-Emitting Diodes (LEDs)
Three System Activity LEDs are included to indicate
the status and actions of the thermostat controller:
• The fan LED is on when the fan is on.
• The heat LED is on when heating is on.
• The cool LED is on when cooling is on.
The Status LED, located beneath the cover, flashes at
5-second intervals to provide indication of the network
status of the thermostat controller. See Table 3.
Backlit Liquid Crystal Display (LCD)
The thermostat controller includes a 2-line, 8-character
backlit display. Low-level backlighting is present during
normal operation, and it brightens when any user
interface key is pressed. The backlight returns to low
level when the thermostat controller is left unattended
for 45 seconds.
Status Display Menu
The Status Display Menu is displayed during normal
operation. This menu continuously scrolls through the
following parameters:
• Room Temperature
• System Mode
• Occupancy Status (Occupied/Unoccupied/
Override)
• Applicable Alarms – The backlight lights up as an
alarm condition is displayed.
Note: An option is available within the Installer
Configuration Menu to lock out the scrolling display and
show only the Room Temperature parameter.
Configuring the Thermostat Controller
The thermostat controller ships from the factory with
default settings for all configurable parameters. The
default settings are shown in Table 5. To reconfigure
the parameters using the user interface keys, follow the
steps in this section.
1. To access the Installer Configuration Menu, press
and hold the OVERRIDE key for approximately
8 seconds.
Note: If the Password parameter is configured,
Password 0 appears on the thermostat controller
display indicating that the configured password is
required to proceed. Use the UP/DOWN arrow
keys to indicate the configured password, then
press the MODE key to proceed through the
Installer Configuration Menu parameters.
2. Once the Installer Configuration Menu begins,
press and release the OVERRIDE key to scroll
through the parameters listed in Table 5.
3. When the desired parameter is displayed, use the
UP/DOWN arrow keys to choose the desired
selection option.
4. Press and release the OVERRIDE key to continue
scrolling through the parameters.
Pressing the FAN key during configuration restarts the
list of displayed parameters at the first parameter listed
in Table 5.
When the thermostat controller is in the Installer
Configuration Menu and left unattended for
approximately 8 seconds, the thermostat controller
reverts to the Status Display Menu.
Configuring Inputs BI1, BI2, and UI3
When BI1 and BI2 are configured for an alarm
condition, an alarm condition displays locally when the
input closes. An alarm message is included on the
scrolling Status Display Menu and when the message
is displayed, the backlight momentarily lights up.
The UI3 input provides changeover of hot/cold water
switching, or supply air temperature monitoring at the
thermostat controller.
Each input can be configured to the Selection Options
included in Table 4.
Table 3: Status LED
Flashes per
5-Second
Interval
Condition Indicated
1Power On
2Power On, Communicating
3Power On, Communicating, Found
Wireless Network
4Power On, Communicating, Found
Wireless Network, Communicating with
TEC20 Coordinator

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 7
Configuring the Sequence of Operation
(SeqOpera)
Choose the appropriate sequence of operation. The
modes presentedare user-dependent on the sequence
of operation selected. For applications using a
changeover sensor, choose the selection option
(0): Cooling Only. Changeover occurs between
Cooling Only and Heating Only. See Figure 9 through
Figure 12 for sequence of operation example.
Table 4: Selection Options for Sequence of Operation
Selection Option Control Curve Terminal Numbers Used
(See Figure 5.)
0: Cooling Only See Figure 9. 10: Proportional Cooling
1: Heating Only See Figure 10. 10: Proportional Heating
2: Cooling and Reheat See Figure 11. 6 and 7: Reheat
10: Proportional Cooling
3: Heating and Reheat See Figure 12. 6 and 7: Reheat
10: Proportional Heating
Figure 9: Cooling Only
Temperature Increase
(Increments of 1F°/0.5C°)
Device Closed
Cooling Setpoint
Device Opened
Proportional
Output
FIG:clng_nly
Figure 10: Heating Only
Temperature Increase
(Increments of 1F°/0.5C°)
Device Closed
Heating Setpoint
Device Opened
Proportional
Output
FIG:htng_nly
Figure 11: Cooling with Reheat
Temperature Increase
(Increments of 1F°/0.5C°)
Heating Setpoint
Device
Closed
Cooling Setpoint
Device
Opened
FIG:clng_wth_rht
Deadband
Reheat Proportional
Output
Heating Output
Cooling Output
Off
Off
On
On
Figure 12: Heating with Reheat
Temperature Increase
(Increments of 1F°/0.5C°)
FIG:htg_wt
h_rht
0%
100%
Reheat
Proportional
Output
Off
Off
On
On

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
8
Configuring the Wireless Mesh Network
Settings
Use the following process to configure the wireless
mesh network.
1. Select a PAN ID and Channel. Use these same
values for every TEC Wireless Thermostat
Controller (and the associated TEC20 Coordinator)
on the same wireless mesh network. See Table 5.
2. Select a Com Address for each TEC Wireless
Thermostat Controller (1 to 254). This address
must be unique to each TEC Wireless Thermostat
Controller on the same wireless network (that is,
unique to the PAN ID/Channel combination). See
Table 5.
After configuring the wireless mesh network settings,
refer to the TEC20xx-4 and TEC20xx-4+PIR Series
Wireless Thermostat Controller System Technical
Bulletin (LIT-12011596) for directions on integrating the
TEC Wireless Thermostat Controllers and TEC20
Coordinator with a supervisory controller.
Table 5: Installer Configuration Menu (Part 1 of 6)
Parameter
Appearing
on Display
Description and Default Selection Options
Pswrd Sets the protective access
password to prevent unauthorized
access to the Installer Configuration
Menu.
Default: 0
Note: The default setting does not
lock out access to the Installer
Configuration Menu.
Range: 0to 1,000
Com addr Wireless address at the thermostat
controller; Default: 254 Range: 000 to 254
Addresses of each item on the wireless bus must be uniquely
numbered, increasing from 1.
Note: Setting this parameter to 0 disables the function.
PAN ID Sets the Personal Area Network
Identification (PAN ID) of the
wireless network. All devices on a
network must have the same
PAN ID setting to communicate with
each other. Default: 0
Range: 0to 500
Note: Setting this parameter to 0 disables the function.
Channel Sets the mesh network channel the
device uses for communication.
Only devices using the same mesh
network channel can communicate
with each other. Default: 10
Range: 11 to 26
Note: Setting this parameter to 10 disables the function.
GET FROM Parameter not available at this time. N/A

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 9
BI1 Configuration of Binary Input 1.
Default: None (None): No function is associated with an input. (Rem NSB): Remote Night Setback (NSB) via a time clock input, an
occupancy sensor, or from a voltage-free contact.
Contact open = Occupied; contact closed = Unoccupied.
(MotionNO*): Temporary occupancy request via a motion detector
input. Contact open = Unoccupied. When the contact closes, the
thermostat controller enters the occupied mode for a specified
TOccTime. Once the TOccTime begins, the thermostat controller
remains in the occupied mode if the contact is open, until the
TOccTime expires.
(MotionNC*): Temporary occupancy request via a motion detector
input. Contact closed = Unoccupied. When the contact opens, the
thermostat controller goes into the occupied mode for a specified
TOccTime. Once the TOccTime begins, the thermostat controller
remains in the occupied mode if the contact is closed, until the
TOccTime expires.
(Window**): Cancels the heating or cooling action when a window
is open. A Window alarm is displayed indicating that the window
needs to be closed to resume heating or cooling.
* These settings disable any local override function.
**When this setting is selected, the heating and/or cooling outputs
are enabled only when the contact is closed. If the fan is set to Auto,
it is enabled only when the contact is closed. If the fan is set to On, it
is not affected by this setting.
BI2 Configuration of Binary Input 2.
Default: None (None): No function is associated with an input. (Door Dry): Door contact only has an effect if BI1 is set to
MotionNO or MotionNC. (See the BI1 parameter earlier in this
table.) The occupancy is now dictated via BI1 and BI2. Any motion
detected sets the zone to Occupied status. The zone remains
permanently in occupied mode until the door contact switch opens
momentarily. The thermostat then enters stand-by mode. If more
movements are detected, the occupied mode resumes. Use a
Normally Closed contact switching device. Contact opened = Door
opened, Contact closed = Door closed.
(RemOVR): Temporary occupancy request by means of a remote
input. This override function is controlled by a manual remote
occupancy override. When enabled, this condition disables the
override capability of the thermostat controller.
(Filter): A Filter alarm is displayed. This alarm can be connected to
a differential pressure switch that monitors a filter.
(Service): A Service alarm is displayed on the thermostat controller
when the input is energized. This input can be tied into the air
conditioning unit control card, which provides an alarm should there
be a malfunction.
Table 5: Installer Configuration Menu (Part 2 of 6)
Parameter
Appearing
on Display
Description and Default Selection Options

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
10
UI3 Configuration of Universal Input 3.
Default: None (None): No function is associated with an input. (COC/NH): Changeover Contact/Normally Heat: A dry contact input
is used to signal seasonal hot/cold water changeover. The contact
closes when cold water is present. Valid only for two-pipe systems.
(COC/NC): Changeover Contact/Normally Cool: A dry contact input
is used to signal seasonal hot/cold water changeover. The contact
closes when hot water is present. Valid only for two-pipe systems.
(COS): Changeover analog Sensor: Used for hot/cold water
changeover switching. Valid only for two-pipe systems.
Note: Choose the selection option (0): Cooling Only for the
SeqOpera parameter to allow changeover to occur between
Cooling Only and Heating Only. Choose the selection option (2):
Cooling and Reheat to allow changeover to occur between
Cooling and Reheat and Heating and Reheat.
(SS): Supply Air Sensor Monitoring
Note: If UI3 is set to None, COC/NH, or COC/NC, then UI3 Status
is available as a point for integration and Supply Temperature is
not available as a point for integration. If UI3 is set to COS or SS,
then Supply Temperature is available as a point for integration and
UI3 Status is not available as a point for integration.
MenuScro Gives the option of having the
display continuously scroll the
parameters.
Default: on
(off): The scroll is inactive.
(on): The scroll is active.
AutoMode Enables the Auto function (if
Option 2 is chosen in the SeqOpera
parameter) to be visible within the
MODE key menu. (The MODE key
is the key at the far left of the cover.)
Default: on
(on): The Auto function is active (Off-Auto-Heat-Cool). Provides
automatic changeover between heating and cooling.
(off): The auto function is inactive (Off-Heat-Cool).
C or F Provides temperature scale options
for display.
Default: °F
(°C): Celsius scale
(°F): Fahrenheit scale
Lockout Selectable Lockout Levels for
limiting end user keypad interaction.
Default: 0
Lockout
Level Function
Mode
Setting Fan Setting Local Override Occupied Temperature
Setpoints
(0) Access Access Access Access
(1) Access Access No Access Access
(2) No Access No Access Access Access
(3) No Access No Access No Access Access
(4) No Access No Access Access No Access
(5) No Access No Access No Access No Access
SeqOpera Determines the sequence of
operation.
Default: 1
(0): Cooling Only (Off-Cool). The default is Cool.
(1): Heating Only (Off-Heat). The default is Heat.
(2): Cooling and Reheat (Off-Auto*-Heat-Cool). The default is Auto.
(3): Heating and Reheat (Off-Heat). The default is Heat.
* Auto can be disabled with the AutoMode parameter. When Auto is
disabled, the default for (2) is Heat.
Note: Choose the selection option (0): Cooling Only when using a
changeover sensor to allow changeover to occur between Cooling
Only and Heating Only.
Table 5: Installer Configuration Menu (Part 3 of 6)
Parameter
Appearing
on Display
Description and Default Selection Options

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 11
St-By TM Sets stand-by timer value; time
delay between moment where
occupancy sensor detected the last
movement in the area and the time
whichthe thermostatstand-by mode
and setpoints become active.
Default: 0.5 hours
Range: 0.5 to 24.0 hours, in 0.5 hour increments
Unocc TM Sets Unoccupied Timer Value; time
delay between the moment where
the thermostat controller toggles to
stand-by mode and the time which
the thermostat controller
unoccupied mode and setpoints
become active.
Default: 0.0 hours
0.0 hours or Factory Value: Setting this parameter to its default 0
value disables the occupied timer and prevents the thermostat
controller from drifting from stand-by mode to unoccupied mode
when occupancy sensor functions are used.
Range: 0.0 to 24.0 hours in 0.5 hour increments
St-By HT Sets Stand-by heating setpoint;
value is between occupied and
unoccupied heating setpoints.
Default: 69.0°F/20.6°C
Range: 40.0°F/4.5°C to
90.0°F/32.0°C Note: When adjusting the temperature, press the UP/
DOWN arrow keys to
change the temperature in
0.5F°/0.5C° increments;
press and hold the
UP/DOWN arrow keys
to change the temperature
in 5.0F°/5.0C° increments.
St-By CL Sets Stand-by cooling setpoint limit;
value is between occupied and
unoccupied cooling setpoints.
Default: 78.0°F/25.6°C
Range: 54.0°F/12.0°C to
100.0°F/37.5°C
Unocc HT Sets the Unoccupied Heating
setpoint value.
Default: 62.0°F/16.5°C
Range: 40.0°F/4.5°C to
90.0°F/32.0°C
Unocc CL Sets the Unoccupied Cooling
setpoint value.
Default: 80.0°F/26.5°C
Range: 54.0°F/12.0°C to
100.0°F/37.5°C
Heat max Sets the Occupied and Unoccupied
maximum Heating setpoint values.
Default: 90.0°F/32.0°C
Range: 40.0°F/4.5°C to
90.0°F/32.0°C
Cool min Sets the Occupied and Unoccupied
minimum Cooling setpoint values.
Default: 54.0°F/12.0°C
Range: 54.0°F/12.0°C to
100.0°F/37.5°C
Pband Proportional Band used by the PI
temperature control loop of the
thermostat controller.
Pband is not converted with C or F
scale and is always shown with a
range of 3 to 10.
Default: 3(3F°/1.7C°)
Value F Scale Pband/C Scale Pband
33.0F°/1.7C°
44.0F°/2.2C°
55.0F°/2.8C°
66.0F°/3.3C°
77.0F°/3.9C°
88.0F°/4.4C°
99.0F°/5.0C°
10 10.0F°/5.6C°
Note: The use of a larger proportional band is not to use the
thermostat controller as a discharge air controller device. The use of
a larger proportional band can be used to solve issues for flawed
HVAC design with basic sizing and thermostat controller location
errors that cannot be worked around.
Table 5: Installer Configuration Menu (Part 4 of 6)
Parameter
Appearing
on Display
Description and Default Selection Options

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
12
Set type Provides the option of temporarily
changing the heating or cooling
setpoint by pressing the UP/DOWN
arrow keys.
Default: permnent
(temporar): Local changes to the heating or cooling setpoints are
temporary, and remain effective for the specified TOccTime.
(permnent): Local changes to the heating or cooling setpoints are
permanently stored in the thermostat controller memory.
Spt Func Determines the operation and
usage of the local setpoint interface
by the user.
Default: Dual Stp
(Attch Stp): Single Occupied Setpoint Adjustment. The displayed
setpoint is the setpoint from the last action taken by the thermostat
controller, or the setpoint currently in use. Both the heating and
cooling setpoints are changed simultaneously, while respecting the
minimum configured deadband. If one setpoint is desired over the
other, use the MODE key to toggle between the two setpoints.
(Dual Stp): Dual Occupied Setpoint Adjustment. The displayed
setpoint is the setpoint from the last action taken by the thermostat
controller, or the setpoint currently in use. The heating and cooling
setpoints can be separated individually, allowing the minimum
configured deadband to expand. If one setpoint is desired over the
other, use the MODE key to toggle between the two setpoints.
TOccTime Sets the duration of the Temporary
Occupancy Time (when the
thermostat controller is in the
Unoccupied mode) when a
Schedule Override Function is
enabled using either the Main User
Menu or BI1 or BI2 configured as a
temporary override remote contact
(RemOVR).
Sets the effective duration of the
Temporary heating or cooling
setpoints set using the
UP/DOWN arrow keys.
Default: 2.0 hrs
Range: 0.0 to 24.0 hrs adjustable in 1-hour increments
Deadband Sets the minimum deadband
between the heating and cooling
setpoints.
Default: 2.0F°/1.0C°
Range: 2.0F°/1.0C° to 5.0F°/2.5C° (adjustable in 1.0F°/0.5C°
increments)
Cal RS Sets the desired room air sensor
calibration (offset). The offset can
be added to or subtracted from the
actual displayed room temperature.
Default: 0.0F°/0.0C°
Range: -5.0F°/-2.5C° to 5.0F°/2.5C° (adjustable in 1.0F°/0.5C°
increments)
Table 5: Installer Configuration Menu (Part 5 of 6)
Parameter
Appearing
on Display
Description and Default Selection Options

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 13
Troubleshooting
See Table 6 for display messaging. Refer to the
TEC20xx-4 and TEC20xx-4+PIR Series Wireless
Thermostat Controller System Technical Bulletin
(LIT-12011596) for troubleshooting details.
Accessories
All the accessories in Table 7 include mounting
hardware; contact the nearest Johnson Controls
representative to order any of these parts.
Note: Review the technical specifications of the
accessories prior to their use in an application.
Aux cont Determines the auxiliary contact
function and configuration.
Default: 0
(0) Not used,
or used for
reheat
If the SeqOpera is set to reheat (Option 2
or 3), ignore this parameter.
(1) Auxiliary
N.O. Occupied = contact closed
Unoccupied = contact
open
The output
aligns with
occupancy.
(2) Auxiliary
N.C. Occupied = contact open
Unoccupied = contact
closed
(3) Auxiliary
N.O. Occupied and fan On = contact closed
Unoccupied and fan On
or Off = contact open
The output
aligns with
occupancy
and the
fan on
command.
(4) Auxiliary
N.C. Occupied and fan On = contact open
Unoccupied and fan On
or Off = contact closed
(5) Auxiliary On/Off control through the
auxiliary network command. The output
can be commanded through the network
for any required auxiliary functions via a
separate and dedicated network
variable.
The output
aligns with
the
secondary
network
occupancy
command.
DA/RA Choice of direct or reverse acting
analog output signal.
Default: DA
(RA): Reverse acting, 0 to 100% = 10 to 0 VDC
(DA): Direct acting, 0 to 100% = 0 to 10 VDC
Reheat Sets the duty cycle time for reheat
output (if Option 2, 3, or 5 is chosen
in the SeqOpera parameter).
Default: 0
(1): 10 seconds (six cycles per minute), for various equipment with
solid-state relays that withstand short duty cycles such as electric
heat.
(0): 15 minutes (four cycles per hour), for various equipment with
mechanical relays or contactors controlling mechanical reheat
systems.
UI3 dis Displays the supply or changeover
temperature when UI3 is configured
as an analog input (supply sensor or
changeover sensor). Used as a
diagnostic/service help, to
troubleshoot and diagnose sensor
operation.
Default: -40°F/-40°C
Used as a diagnostic/service help, to troubleshoot and diagnose
sensor operation.
Table 5: Installer Configuration Menu (Part 6 of 6)
Parameter
Appearing
on Display
Description and Default Selection Options

TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions
14
Repair Information
If the TEC2045-4 Wireless Thermostat Controller fails
to operate within its specifications, replace the unit. For
a replacement thermostat controller, contact the
nearest Johnson Controls representative.
Table 6: Display Messages
Display Function
Service Indicates that there is a service alarm in accordance with the programmable Binary Input (BI2).
Filter Indicates that the filter(s) is dirty in accordance with the programmable Binary Input (BI2).
Window Indicates that an outside window or door is open and has cancelled the thermostat controller heating or
cooling action in accordance with the programmable Binary Input (BI1).
Table 7: Accessories (Order Separately)
Code Number Description
SEN-600-41Remote Indoor Air Temperature Sensor with Occupancy Override and LED
TE-6361M-12Duct Mount Air Temperature Sensor
TE-636S-1 Strap-Mount Temperature Sensor
TEC-6-PIR3Commercial Fan Coil Controller Cover for Occupancy Sensor
TEC20-A-1 Replacement Antenna for TEC20 Coordinator
TEC20-RA-14Remote Antenna for TEC20 Coordinator
NPB-PWR5DIN Rail Mount 24 VAC/DC Power Module for TEC20 Coordinator
TEC20-8X-1 120 VAC to 15 VDC Power Supply for TEC20 Coordinator
TEC20-9B-1 Replacement Battery Pack for TEC20 Coordinator
1. Only the occupancy override function can be accomplished using the SEN-600-4 with the TEC2045-4.
2. Additional TE-636xx-x Series 10k ohm Johnson Controls Type II Thermistor Sensors are available; refer to the
TE-6300 Series Temperature Sensors Product Bulletin (LIT-216320) for more details.
3. The TEC-6-PIR Accessory Cover can be used to replace the existing cover on a non-PIR TEC2045-4 Thermostat
Controller to provide occupancy sensing capability.
4. This antenna is used when the TEC Coordinator is installed inside a metal cabinet, or when a remote antenna is required by
physical installation.
5. DIN Rail: Type NS35/7.5 (35 x 7.5 mm) and DIN rail end clips. Length of DIN rail depends on the number of DIN rail
mounted options.

Published in U.S.A. www.johnsoncontrols.com
TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and One-Speed Fan Control
Installation Instructions 15
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2010 Johnson Controls, Inc.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Technical Specifications
TEC2045-4 Wireless Thermostat Controller with Single Proportional Output and
One-Speed Fan Control
Power Requirements 19 to 30 VAC, 50/60 Hz, 2 VA (Terminals 4 and 5) at 24 VAC Nominal, Class 2 or
Safety Extra-Low Voltage (SELV)
Analog Output Rating 0 to 10 VDC into 2k ohm Resistance (Minimum)
Fan Relay Output Rating 19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush, Class 2 or SELV
Auxiliary Output Rating Triac Output: 19 to 30 VAC, 1.0 A Maximum, 15 mA Minimum, 3.0 A In-Rush
Binary Inputs Voltage-Free Contacts across Terminal Scom to Terminals BI1, BI2, or UI3
Analog Inputs Resistive Inputs (RS and UI3) for 10k ohm Johnson Controls Type II Negative
Temperature Coefficient (NTC) Thermistor Sensors
Temperature Sensor Type Local 10k ohm Negative Temperature Coefficient (NTC) Thermistor
Wire Size 18 AWG (1.0 mm Diameter) Maximum, 22 AWG (0.6 mm Diameter) Recommended
Recommended Transmission
Range Through Walls: 10 m (30 ft) Line-of-Sight (Open Space): 30 m (100 ft)
RF Band Direct-Sequence Spread-Spectrum Transmission; 2.4 GHz unlicensed band
Transmission Power 10 mW Maximum
Resolution ±0.1C°/±0.2F°
Temperature Range Backlit Display: -40.0°C/-40.0°F to 50.0°C/122.0°F in 0.5° increments
Heating Control: 4.5°C/40.0°F to 32.0°C/90.0°F
Cooling Control: 12.0°C/54.0°F to 38.0°C/100.0°F
Accuracy ±0.5C°/±0.9F°/ at 21.0°C/70.0°F Typical Calibrated
Minimum Deadband 1C°/2F° between Heating and Cooling
Ambient Conditions Operating: 0 to 50°C (32 to 122°F); 95% RH Maximum, Noncondensing
Storage: -30 to 50°C (-22 to 122°F); 95% RH Maximum, Noncondensing
Compliance (Pending) United States:
UL Listed, File E27734, CCN XAPX,
Under UL 873, Temperature Indicating and Regulating Equipment
FCC Compliant to Part 15.247 Regulations for Low Power Unlicensed Transmitters
Transmitter FCC Identification: (pending)
Canada:
UL Listed, File E27734, CCN XAPX7,
Under CAN/CSA C22.2 No. 24, Temperature Indicating and Regulating Equipment
Industry Canada, ICES-003
Industry Canada (IC) Identification: (pending)
Shipping Weight 0.34 kg (0.75 lb)
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.