Joie trillo User manual

2/3(15–36kg)
trillo
high back booster

Welcome to Joie™
Congratulations on becoming part of the Joie family! We are so excited
to be part of your journey with your little one. While traveling with Joie
trillo TM high back booster you are using a high quality, fully certified
safety Group 2/3 booster. This product is suitable for use with children
weighing 15-36kg (approximately 3-12 years old). Please carefully read
this manual and follow each step to ensure a comfortable ride and best
protection for your child.
Please confirm
This booster can be installed using a 3 point retractable adult seat belt
approved to ECE Regulation No. 16 or other equivalent standards.
Booster
! IMPORTANT: KEEP FOR FUTURE REFERENCE. PLEASE READ CARE-
FULLY.
Please keep the instruction manual in the
storage compartment at the bottom of
the booster as right figure.
GB
1
2
3
6
8
7
1
4
2
Parts List
Make sure all parts are available before assembly. If any part is missing,
please contact local retailer. No tools are required for assembly.
Accessories (May not be included)
5
1 Side Impact Shield (on certain models)
2 Cupholders (on certain models)
1 Head Support
2 Lower Back Support
3 Armrest
4 Base
5 Adjustment Button
6 Head Support Adjustment Lever
7 Shoulder Belt Guide
8 Latch Connector
Accessories may be sold separately or may
not be available depending on region.

1 2
WARNING WARNING
!Do take care to locate and install the booster so
that it is not liable to become trapped by a move-
able seat or in a door of the vehicle.
!This booster is designed ONLY for child weighing
15-36kg (approximately 3-12 years old or under).
!Failure to properly use this booster increases the
risk of serious injury or death in a sharp turn,
sudden stop or crash.
!DO NOT use another manufacturers soft goods
with this booster. See your retailer for Joie replace-
ment parts only.
!DO NOT use in any configuration not shown in the
instructions.
!According to accident statistics, Children are safer
when properly restrained in rear vehicle seating
positions, rather than front seating positions. For a
vehicle with a front passenger air bag, refer to your
vehicle owner’s manual as well as these instruc-
tions for a booster installation.
!NEVER leave your child unattended.
!Any straps of vehicle seat should be tightened and
not twisted.
!After your child is placed in this child restraint, the
safety belt must be used correctly, and ensure that
any lap strap is worn low down, so that the pelvis is
firmly engaged.
!NEVER leave a booster unsecured in your vehicle.
An unsecured booster can be thrown around and
may injure occupants in a sharp turn, sudden stop
or crash. Remove it or make sure that it is securely
belted in the vehicle.
!NEVER leave luggage or other objects unsecured
in a vehicle, they are liable to cause injuries in the
event of a collision.
!Replace the booster after an accident of any kind.
An accident can cause damage to the booster that
you cannot see.
!DO NOT modify your booster or use any accesso-
ries or parts supplied by other manufacturers.
!NEVER use a booster if it has damaged or missing
parts. DO NOT use a cut, frayed or damaged
vehicle seat belt.
!NEVER give this booster to someone else without
also giving them this manual.

3 4
!The booster can become very hot if left in the sun.
Contact with these parts can burn your child’s
skin. Always touch the surface of any metal or
plastic parts before putting your child in the
booster.
!NEVER use a second-hand booster or a booster
whose history you do not know.
!DO NOT use this booster without the soft goods.
!DO NOT use any load bearing contact points other
than those described in the instructions and
marked on the booster.
!DO NOT face your booster toward the rear of the
vehicle.
!To avoid burns, never put hot liquids in your
cupholders.
! DO NOT use this child seat for more than 10 years
after the date of purchase, as parts may degrade
over time, or from exposure to sunlight, and may not
perform adequately in a crash.
! The soft goods should not be replaced with any
besides the ones recommended by the manufacturer,
because the soft goods constitute an integral part of
the booster performance.
WARNING Emergency
In case of emergency or accidents, it is most important to have
your child taken care of with first aid and medical treatment
immediately.
Product Information
Read all the instructions in this manual before using this
product. If in doubt, consult either the booster manufacturer or
the retailer.
1. This booster is a ‘Universal’ child restraint. It is approved
to UN ECE regulation 44, 04 series of amendments, for
general use in vehicles and it will fit most, but not all, car
seats.
2. A correct fit is likely if the vehicle manufacturer has declared
in the vehicle handbook that the vehicle is capable of
accepting a ‘Universal’ child restraint for this age group.
3. This booster has been classified as ‘Universal’ under
more stringent conditions than those which applied to earlier
designs which do not carry this notice.

5 6
For Installation with Latch System and 3-point-belt
1. This booster is a ‘Semi-Universal’ child restraint. It is
approved to UN ECE regulation 44, 04 series of amendments
for general use in vehicles fitted with ISOFIX anchorages
systems.
2. It will fit vehicles with positions approved as ISOFIX
positions (as detailed in the vehicle handbook), depending on
the category of the booster and of the fixture.
3. If in doubt, consult either the booster manufacturer or
vehicle manufacturer.
Product Booster
Suitable for Child weighing15-36kg
Mass Group Group 2/3
Materials Plastics, metal, fabrics
Patent No. Patents pending
Booster Assembly
Assemble Head
Support
see images 1- 3
1. Booster taken from the carton
as 1
2. Flip head support and lower
back support over as shown.
2
! Squeeze adjustment lever
2-1 and slide two pieces
together until they snap into
place. 2-2
1
2
1
2
3

7 8
see images 7
see images 8- 11
Assemble Lower
Back Support
see images 4- 6
1. When attaching backrest to
base, please press backrest
down strongly.“U”-shaped
hooks on bottom of backrest
will interlock with bars on
base. 4
!Shake the backrest to make
sure the recline mount is
correctly fixed.
!Do not use this booster
base separately.
2. The completely assembled
booster is shown as 6
4
5
6
Height Adjustment
for Head Support
7
Concerns on Installation
89
10

910
2
11
1
23
4
56
1
23
4
56
1
Installation with 3-point-belt
see images 12 - 23
If vehicle is equipped with ISOFIX,
the vehicle lower anchor points
may be visible at the vehicle seat
crease. See your vehicle owner’s
manual for exact locations,
anchor identification, and
requirements for use.
1. Place the booster in forward-
facing position on a forward-
facing vehicle seat with
anchors, hook latch
connectors to vehicle anchors.
12
!NEVER put two latch
connectors on one vehicle
ISOFIX anchor unless
specifically allowed by the
vehicle manufacturer.
2. Secure the booster firmly by
pushing it downward with
knee or hand while pulling the
adjustment belt. 13
3. For ease of unhooking, extend
the adjustment belt to its
maximum length while
pressing the adjustment
button. 14
!The latch connectors can be
detached for use from the
compartment on the bottom
where it is stored. 15
12
!
!
14
13
15

11 12
17
16
20
19
18
3
12
4
4. Please make sure that the
backrest of the child safety
seat rests flat against the
backrest of the car seat so that
the child seat is under no
circumstances in a reclined
position. 17 Pull the vehicle
safety belt and pass through
the belt path 18 , and then
buckle it up. 18 -3
! Position shoulder belt
through the shoulder belt
guide shown in 18 -1
! DO NOT position vehicle
belt over top of the
armrests. It must pass
underneath the armrests.
18 -2
! The lap belt must be low
down on hips. The booster
is shown as 18
!The booster can not be used
if the vehicle safety belt
buckle (female buckle end)
is too long to anchor the
booster securely.18 -4
! To ensure the correct head
support height is obtained,
the bottom of the headrest
MUST be even with the top
of child’s shoulders as
shown in 19 and the
shoulder belt must be
positioned in the red zone
as shown in 20 .
! Place a booster firmly
against the back of a
forward-facing vehicle seat
equipped with a lap/
shoulder belt.
! Have your child sit in a
booster with their back
flat against back of a
booster.

13 14
! NOT as shown in 22 . Fasten
buckle and pull up on the
shoulder belt to tighten.
! If the belt lays across child
neck, head or face, readjust
head support height.
! Belt must not be twisted.
21
22
23 1
PULL
Detach Soft Goods
see images 23
Open 2 pairs of buttons and 6 pairs of elastics on the back of
soft goods to remove it. 23
!Pull down to remove button as 23 -1
To refit the seat pad simply reverse the steps above.
Assemble Side
Impact Shield
see images 24 - 26
Align the side impact shield with
the slot of lower back support
plastics mounts, and then insert
to lock. 24
The completely assembled
booster is shown as 26
Accessories (May not be
included in purchase)
26
25
24

15 16
Use Cupholders
see images 27
!Please wash the soft goods and inner padding with cold
water under 30°C.
!Do not iron the soft goods.
!Do not bleach or dry clean the soft goods.
!Do not use undiluted neutral detergent, gasoline or other
organic solvent to wash the booster. It may cause damage
to the booster.
!Do not twist the soft goods and inner padding to dry with
great force. It may leave the soft goods and inner padding
with wrinkles.
!Please hang dry the soft goods and inner padding in the
shade.
!Please remove the booster from the vehicle seat if not in
use for a long period of time. Put the booster in a cool, dry
place and somewhere your child cannot access it.
Care and Maintenance
12
27
NOTE