JONR ED12 User manual

Cordless wet & dry vacuum cleaner
ED12
This picture is for reference only, and
the actual product shall prevail.
User Manual
Please read this manual carefully before use, and keep it properly for further reference.

Table of Content
Product Introduction .................................................. 4
Installation ............................................................... 7
Product Technology and Parameters .......................... 11
Maintenance and Service .......................................... 12
After-Sales Service .................................................. 16
Description of Hazardous Substances ........................ 15
Safety Specifications ................................................. 1
Product Summary ...................................................... 8
Warranty Card ......................................................... 17

Unless supervised or instructed by an adult guardian who can ensure that this product
can be operated safely and properly, persons with physical, sensory, or intellectual
disabilities or without experience and knowledge, including children, are prohibited from
using this product.
• Children are prohibited from operating this product or using it as a toy. Close attention is
required when children, pets, or plants are nearby or this product is operated near them;
children are prohibited from cleaning or maintaining the product without supervision by
their guardian.
• Plastic films used for product packaging may be dangerous, and they shall be kept away
from children to avoid choking.
• This product is suitable for hard indoor floors; optimal results will not be achieved when
used on uneven floors.
• As this product body and its floor brush have electrical components, they cannot be
immersed in water or liquid. Do not operate this product unless all parts are installed.
• Do not touch the outlet, power adapter, or display with wet hands to avoid the risk of
electric shock.
• Please remove the plug from the power socket and make sure that the product is in the
power-off state when it is out of service or before cleaning, cleaning, maintaining, or
repairing the product. When cleaning the roller brush, please turn off the main machine
to prevent damage caused by the rotating roller brush. Do not operate this product if the
roller brush, clean water tank, wastewater tank, or filter sponge is not installed in place.
• Do not use this product for flammable or highly volatile liquids and other chemically
hazardous liquids (such as gasoline, kerosene, paints, and perfumes) or in areas where
flammable or combustible liquids may be present. Otherwise, a short circuit or explosion
of the product may occur.
• Do not use this product for toxic or harmful substances (chlorine bleach, ammonia, drain
cleaner); or for sweeping hard or sharp objects (such as glass, nails, screws, and coins);
or for removing unextinguished heat sources such as cigarette butts and matches to
avoid fire.
• Do not use this product for removing powdered ink or toner in laser printers and copiers
to avoid fire or explosion.
• Do not use this product for removing strong stains such as pigments, paints, and shoe
polish.
• Do not use this product for foam-type cleaning liquids to avoid damage to the motor.
• Do not operate this product in an enclosed space filled with paint thinners emitting from
the oily paint or with some anti-moth matter, combustible dust, or other explosive or toxic
materials.
• Before use, ensure that any human hair, loose clothing, fingers, and body parts are kept
away from the openings and moving parts of this product and its accessories.
• Do not block the air inlet and outlet to avoid machine overheating. Do not put any object
at the suction port of the product. Do not operate this product when the suction port of the
product is blocked. Please remove the dust, cotton wool, hair, or other items timely
because they may cause the reduced airflow of the product.
• Please keep the ambient temperature in the range of 0-40°C when charging, storing, and
operating this product.
• Please operate this product strictly according to the instructions in the manual.
In order to avoid accidental injuries such as electric shock and fire caused by improper
operation, please read the User Manual carefully before use and keep this manual
properly for further reference. This product is designed only for household use rather
than outdoor use, non-ground use, commercial or industrial environments.
1
Warning
Safety Specifications

2
Battery and Charging
• Please only use the type of liquid specified in the operating section of this manual, and
its usage volume shall meet the regulations. Do not add other solutions (such as alcohol
and disinfectant) without permission.
• Take extra care when cleaning on stairs to prevent falls.
• Please put this product on a level surface. Do not store this product in a place where
icing may occur.
• When lifting or handling this product, ensure that this product is always in the OFF state.
When handling this product, putting your finger on the switch or setting the switch in the
ON state may cause an accident.
• Do not incinerate this product even if it has been severely damaged, because the battery
may catch fire and explode. Please remove the battery before scrapping the product.
• Do not modify or try to repair this product except as described in the operation and
maintenance instructions. Before cleaning or maintaining the product, please remove
the power plug and ensure the power supply is in the OFF state. Repairs should be
conducted by qualified maintenance personnel, and only the same replacement parts
should be used.
• Do not continue to operate this product when it cannot work properly due to drops,
damage, outdoor use, or water ingress. To avoid injury, do not try to run it but send it to
the after-sales service center for repair.
• Before use, if any electric leakage of the product or excessively high temperature/
abnormal sound of the motor, such as body overheating, abnormal sound, and odor are
identified, please stop the product immediately and contact the after-sales service for help.
• Do not immerse the floor brush in water to avoid product burns. Do not shake or impact
the machine violently to avoid wastewater flowing into the motor. When handling the
product, please keep the product in an upright state to avoid wastewater flowing into the
motor.
• Do not charge this product outdoors. This product should only be used with the charging
base and power adapter that come with the product. Otherwise, other types of charging
bases may cause battery failure or extreme thermal effects.
• The charging base has an air-drying function and is only suitable for roller brushes of
floor scrubbers.
• Please follow all charging instructions and do not charge the product beyond the
temperature range specified in the instructions. Improper charging or charging out of the
specified temperature range may cause damage to the battery and increase the risk of fire.
• Be careful to prevent damage to the power cord. Do not drag or lift the product and
charging block with the power cord, and do not use the power cord as a handle; do not
insert the power cord in the door gap, and do not pull the power cord at sharp points and
corners. Do not travel the product on the power cord, and keep the power cord away from
heat sources.
• If the power cord of the power adapter is damaged, it must be replaced by the
manufacturer, its service agent, or similarly qualified personnel to avoid danger.
• Do not hold the product or the plug of the charging base. To pull out the plug, please hold
the plug of the charging base and do not pull the power cord.
• Do not short-circuit the output terminals of the battery pack or charging base.
• Do not charge, remove, heat (60°C and above) or incinerate discarded batteries.
• Do not expose this product to fire or excessive temperatures. Exposure to flames or
temperatures above 130°C may cause an explosion.
• Do not use damaged or modified devices. Using damaged or modified batteries may
cause unpredictable consequences, posing the risk of fire, explosion or injury.
• Liquid may eject from the battery with excessive force. Avoid contact with this liquid. In
Safety Specifications

Safety Specifications
case of accidental contact, please rinse with water. If the liquid enters the eyes, please
seek medical care immediately, as the liquid ejected from the battery may cause irritation
or burns.
• This product must be disconnected from the power source before the battery is removed.
Please put the battery in places out of reach of children; do not discard the battery
without permission, and send it to the professional recycling agency for disposal. Do not
put the battery in your mouth, and seek medical care as soon as possible if it is swallowed.
• The batteries in this product shall only be replaced by qualified technicians or after-sales
personnel.
• If the product is out of service for a long time, turn off the power and remove the plug of the
charging base.
This appliance contains batteries that are non-replaceable.
3

Packing list
Adapter
Manual
Manual
Main engine
Charging base
Product Introduction
*Notes:
The illustrations of the product, accessories and user interface in the manual are
schematic and are for reference only.
The actual product will prevail as the products are improved continuously, and our
company reserves the right to update the product.
4

Product Description
Mode key/self-cleaning key
ON/OFF key
Handle
Clean water tank
Charging base
Roller brush cover
Release button of wastewater tank
Wastewater tank handle
Wastewater tank
Roller brush
Product Introduction
Aluminum tube
Charging socket
5

Product Introduction
H
L
W
L: 28.2cm W: 26cm H: 112cm
6

Handle Diseassembly
Insert the end of the aluminum tube
vertically into the hole on the host until
a “click” sound is heard, and make sure
that the tube is tightly inserted, indicating
that it is installed successfully.
To remove the aluminum tube of the
handle, insert a long, thin, and rigid
object into the hole in the back of the
body to press the elastic sheet while
pulling the machine handle upwards.
Click
Installation
Insert the end of the handle vertically
into the bore of the aluminum tube until
a “click” sound is heard, and make sure
that the handle is tightly inserted,
indicating that it is installed successfully.
7

1. Preparation before use
1) Before use, please check whether your floor scrubber battery has power; if not, please
charge it timely. Do not use it until fully charged. (Recommendation: please fully charge
the product before first use).
Charging method:
Put the machine into the charging base, connect one end of the adapter to the charging
base, and connect the other end to the socket in the home. When charging, put the
machine upright in the charging base, and make it close to the corner of the wall to avoid
injuries such as tripping. During the charging process, the light panel of the machine body
displays the battery status. When fully charged, the light panel goes out. Put the power
cord away when charging is not required.
Please charge the product once every three months if it is out of service for a long time
after purchase (Please be sure to use the charging base equipped with the product for
charging; the charging time is about 4 hours, and fully charging is not required).
Product Summary
Tips
8

2) Fill water in the clean water tank
Open the silicone
stopper and fill
with water
1) Startup: Press the Power button after the product is fully charged to start the machine,
and press this button again to shut down the machine;
2) Mode switching: The AUTO (auto) mode is activated by default after startup. Press the
Mode key to switch to the MAX (powerful) mode. The two modes alternate in turn;
3) Self-cleaning: When the machine is charging, press the self-cleaning button once to
activate the self-cleaning function, and press this button again to deactivate the
self-cleaning function;
Remove the
clean water tank
Install clean water
tank on the body
Product Summary
2. Start to work
Mode key/self-cleaning key
ON/OFF key
1) Self-cleaning of body pipes and roller brush: After use, please the machine into the
charging base timely for charging, and press the self-cleaning button to clean the
machine automatically.
3. Cleaning after use
Tips: Ensure enough water is kept in the clean water tank before self-cleaning.
9

2) Clean the wastewater tank
Install the wastewater tank
Remove the wastewater tank
Product Summary
Open the wastewater tank
Open the wastewater tank
10

Product name
Wireless intelligent floor washer
Product model
ED12 / ED12X / ED12Z / ED12W
Rated voltage
22.2V
Rated power
200W
Li-ion battery capacity
2600mAh
Clean water tank capacity
0.85L
Wastewater tank capacity
0.4L
Net weight
3.63kg
Product dimensions (mm)
1120*260*282
Rated input of the adapter
100-240V~ 50/60Hz 0.45A
Rated output of the adapter
27V 0.5A
Product Specifications and Parameters
11

1.To prevent affecting the working performance of the machine, it is recommended to
regularly clean and maintain the machine body, floor brush, dirt suction port, and
wastewater tank;
2.Before cleaning, stop the machine and clean the machine body with a cloth dipping in
water or neutral detergent; please wring out the cloth to avoid water stains penetrating
the inside of the machine;
3.Wastewater tank cleaning: Please clean the wastewater tank timely every time after
use, and clean the upper cover and filter of the wastewater tank regularly.
☼
Remove the filter, wash
with clean water, and dry
4.Clean the water jet port on the roller brush cover and the roller brush.
• Users can clean the water spray port on the roller brush cover regularly according to the
use conditions to avoid accumulation and scaling of stains to affect water flow.
• Remove the roller brush regularly for cleaning and drying to avoid long-term
micro-wetness of roller brush resulting in odor.
Remove the upper cover
Maintenance and Service
Remove the upper
cover of roller brush
Rinse the upper cover
of roller brush Remove the roller brush
1.Turn the end cap knob
2. Pull out the
roller brush
Wash with clean
water and dry Install the roller brush Install the upper cover
of the roller brush
1. Install the
roller brush
2. Tighten the
end cap knob
12

5.Clean the suction nozzle of the floor brush
If the floor cannot be cleaned
thoroughly after an extended
period of use, please check
whether the suction nozzle of
the floor brush is blocked.
When cleaning the roller brush,
please remove dirt inside the
suction nozzle with a clean
brush or a wet cloth.
6. If any abnormality is identified during the product use, please refer to the table below.
Abnormal
conditions
Possible causes
Solution
The floor
scrubber does
not work, or an
alarm is issued
-The roller brush is wrapped in objects such
as hair
-The wastewater tank is full
-Low battery
-Clean the rollers after
shutting down
-Pour wastewater out of the
wastewater tank
-Charge
Impaired suction
power of the
product
-Roller brush, roller brush cover, and
wastewater tank are not installed in place
-The roller brush is wrapped in objects such
as hair
-The suction nozzle or pipe is blocked
-The filter above the inside of the wastewater
tank is dirty
-The filter of the wastewater tank is dirty or
missing
-Reinstall
-Clean the roller brush
-Remove the obstacles from
the suction nozzle or the
inside of the pipe
-Clean the filter before use
-Clean or install the filter
before use
Abnormal sound
is heard when
the fan is
running
-The suction nozzle is blocked
-The liquid level in the wastewater tank has
reached the specified level
-Remove the obstacles from
the suction nozzle
-Take out the wastewater
tank, pour the wastewater,
and install the tank again
No water is
jetted from the
floor brush
-There is no water in the clean water tank
-The clean water tank is not installed in place
-Fill water in the clean water
tank
-Reinstall the clean water
tank
Water leakage at
the air outlet
-The wastewater tank filter is not dried after
cleaning and use
-Wash, and dry before use
Water leakage
from the bottom
of the floor brush
-No wastewater tank or wastewater tank filter
is installed
-Install the wastewater tank
and filters
In case of failure to solve any fault, please contact the local after-sales service outlet or
call the national service hotline: [phone]
Maintenance and Service
13

7.Description of abnormal conditions of lights
Maintenance and Service
14
Abnormal conditions
Light warning
Solution
Short circuit
The red light is always on
for 1 second
Stop the machine
The wastewater tank is full
The red light is always on
for 2 minutes
Pour wastewater water
The charging temperature
is abnormal
The red light is always on
Reset after the adapter is
removed
The adapter voltage is
abnormal
The red light is always on
Reset after the adapter is
removed
The battery is dead
The red light is always on
Reset after the adapter is
removed
The motor current is
abnormal
The red light is always on
for 2 minutes
Power off the machine and dry
The floor brush is blocked
The red light is always on
for 2 minutes
Remove impurities from the
roller brush
The battery is overheating
The red light is always on
for 2 minutes
Power off the machine and
leave it idle for 30 minutes
The battery is damaged
The red light is always on
for 2 minutes
Contact the customer service
center and sent it to the factory
for repair
The battery is exhausted
The red light is always on
for 2 minutes
Charging base

1.This product meets the requirements of the Management Measures for the Restriction
of the Use of Hazardous Substances in Electrical and Electronic Products.
2.During the environmental protection use period, no harmful substances that affect their
health are leaking or precipitating, and consumers can operate it safely.
3.The environmental protection use period of the company’s products is 10 years. The
“environmental protection use period” is valid only when this product works under
normal conditions as described in this manual.
Part name
Hazardous substances
Pb
Hg
Cd
Cr(VI)
PBB
PBDE
Main body
O
O
O
O
O
O
Clean water tank
assembly
O
O
O
O
O
O
Wastewater tank
assembly
O
O
O
O
O
O
Floor brush assembly
O
O
O
O
O
O
Battery
X
O
O
O
O
O
Electronic circuits
X
O
O
O
O
O
Adapter
X
O
O
O
O
O
Motor assembly
O
O
O
O
O
O
Other accessories
O
O
O
O
O
O
Description of Hazardous Substances
This table is prepared in accordance with the provisions of SJ/T11364
O: Meaning that the content of the hazardous substance in all homogeneous materials of
the component is below the limit specified in GB/T26572.
X: Meaning that the content of the hazardous substance in at least one homogeneous
material of the component exceeds the limit specified in GB/T26572.
(Note: Some of the parts marked “X” above contain hazardous substances that exceed
the limit due to the current technical level of the industry, and substitutes or reductions
cannot be realized temporarily.)
15

The free warranty period of the entire machine is one year, and the warranty will be invalid
for any of the following situations:
1.Corresponding consumables and gifts;
2.Damaged due to improper handling, operation, maintenance, and storage by the user;
3.Damaged due to the charging voltage lower than 100V or higher than 240V;
4.Damaged by failure to follow the user manual for operation, maintenance, and service;
5.Disassembled and repaired by non-professional service personnel not designated by
the company;
6.The warranty period of the product expires;
7.The model or number recorded on the invoice or warranty card is inconsistent with the
actual product;
8.Damaged due to force majeure;
After-Sales Service
Tips:
1.Please keep your purchase invoice and related receipts as an essential basis for
warranty service.
2.This product is only a household one, and the company is not responsible for any
problem caused by its use outside the household.
16

Customer service hotline [phone].
Please keep the warranty card properly and provide the original warranty card and valid
invoice for the repair.
Relevant information (filled in by the user)
User name
Frequently
used phone
Contact address
Product model
Product No.
Purchase store
Date of
purchase
Repair station
Invoice
number
Repair Records
Date of repair
Fault content
Troubleshooti
ng details
Name of the
repair unit
Phone of
repair unit
Signature of
the repairman
Product Certificate
Product Model:
Inspector No.:
Date of check:
Check conclusion:
Warranty Card
17

Manufacturer: Suzhou New Ebao Technology Co.,ltd
Address: 2-201 (1), building 1, Microsystem Park, No. 2, Peiyuan
Road, High-Tech Zone, Suzhou
Contact number: [phone]
E-Mail: [e-mail]
Website: http://jonr.cc
If you have any quesons on the product,
please contact us: [e-mail].