Jonti-Craft Young Time Coat Locker 7106YT User manual

DHCJX –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 1 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
Tools Required:
-4mm Hex Wrench (Provided)
-Medium Phillips Screwdriver
Hardware Included:
Not Actual Size
Instructions for:
7106YT Coat Locker, 5-Section
Hardware Package HCJX
Qty Description
(1) XAUS 4mm Hex Wrench
(32) XAUR 2” Decorative Screw
(12) XCPT #8 X 0-7/8" Washerhead Screw
(10) XBTX #6 Truss Screw
(5) XCLX Almond Double Coat Hook
Parts:
WARNING:
CHOKING HAZARD/SHARP POINTS- Assembly
hardware contains small parts and components
with sharp points. Adult assembly required.

DHCJX –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 2 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
Assembly Instructions:
1. Begin by installing 5-XCLX Nylon Coat Hooks to 1-LH Side-Band 4-Dividers-Fusing 10-XBTX Truss
Screws.
2. Assemble locker face down. Install Shelves-Eto LH Side-Bby aligning dowels in Shelves with dowel
holes in Side. Ensure back groove is up on LH Side, and Shelf ‘rounded edges’ are down. Secure with
4-XAUR Decorative Screws with 4mm Hex Wrench provided.
3. Install 4 Dividers-Fwith rounded edge down. Align Divider cutouts with Shelf cutouts ensuring all coat
hooks are towards the top.

DHCJX –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 3 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
3. Align dowels of Bottom-A with dowel holes in LH side and ‘partially’ install with 2-XAUR Decorative
Screws. Align dowels with each Divider to Bottom dowel holes and install 8-XAUR Decorative Screws.
Tighten XAUR Screws to the LH Side.
4. Align dowels of Top-D with dowel holes in LH side and ‘partially’ install with 2-XAUR Decorative
Screws. Align dowels with each Divider to Top dowel holes and install 8-XAUR Decorative Screws.
Tighten XAUR Screws to the LH Side.
5. Install RH Side-Cto Top, Bottom and Shelves by aligning dowels into dowel holes in RH Side. Secure
with 8-XAUR Decorative Screws with 4mm Hex Wrench provided.

DHCJX –Rev. B –23 October 2019
800-543-4149
507-342-5169
www.jonti-craft.com Page 4 of 4
JonTi-Craft, Inc.
171 Hwy 68
P.O. Box 30
Wabasso, MN 56293
6. Insert 2 Backs-G by inserting into groove on Top and bowing into other groove on the Bottom. Slide
into LH/RH Side grooves.
7. Locate pre-drilled holes in the edge of each Divider and install 6-XCPT Washerhead Screw, do not
tighten!
8. Install remaining 3-Backs in the same manner. Once all backs and screws are installed tighten all
screws.
9. Stand unit upright.
10. If you experience any difficulties when assembling this product, please contact the Jonti-Craft
Customer Relations Team at [phone] or [e-mail]. All other requests for assistance
must be directed to your Jonti-Craft Dealer.
General Care & Maintenance Guidelines: www.jonti-craft.com/generalcare