joyami JDD02M User manual

joyami Smart Blender
Operation Manual
Please read this operation manual carefully before starting the product,
and save it properly for future use.
Please read this operation manual carefully before starting the product,
and save it properly for future use.

01
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety
precautions should always be followed including
the following:
Read all instructions.
To protect against risk of electrical shock do not
put cord, plugs, portable appliances in water or
other liquid.
This appliance is not intended for use by persons
(including children) with reduced physical,
sensory, or mental capabilities, or lack of
experience and knowledge, unless they are
closely supervised and instructed concerning use
of the appliance by a person responsible for their
safety. Close supervision is necessary when any
appliance is used by or near children. Children
should be supervised to ensure that they do not
play with the appliance.
Turn the appliance OFF, then unplug from the
outlet when not in use, before assembling or
disassembling parts and before cleaning. To
unplug, grasp the plug and pull from the outlet.
Never pull from the power cord.
Avoid contacting moving parts.
Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions,
or is dropped or damaged in any manner.
Contact the manufacturer at their customer
service telephone number for information on
examination, repair, or adjustment.

02
The use of attachments, including canning jars,
not recommended by the manufacturer may
cause a risk of injury to p ersons.
Do not use outdoors. Household Use Only.
Do not let cord hang over edge of table or
counter, or touch hot surfaces.
Do not place on or near a hot gas or electric
burner, or in a heated oven.
Keep hands and utensils out of container while
blending to reduce the risk of severe injury to
persons or damage to the blender. A scraper
may be used but must be used only when the
blender is not running (does not apply to an
acceptable scraper integral with the appliance).
Blades are sharp. Handle carefully.
Always operate blender with cover in place.
When blending hot liquids or operating in the
heating mode, remove center piece of
two-piece cover.
Allow to cool before assembling or disassembling
parts and before cleaning the appliance.
Do not touch surfaces that may be hot. Use
handles or knobs provided.
Remove plug from outlet when the appliance is
not in use, before putting on or taking off parts,
and before cleaning. Allow to cool before handling.
Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.
Where applicable, always attach plug to
appliance and check that the control is OFF
before plugging cord into wall outlet. To
disconnect, turn the control to OFF, then remove
plug from all outlet.

03
Do not use appliance for other than intended use.
Avoid contacting moving parts.

04
Cleaning & maintenance
Do not immerse the blender in water or splash
it with water.
Do not use steel wool or other hard objects to
clean the heating plate.
Use only soft cloths for cleaning.
If the blender will not be used for an extended
period of time, unplug the power cord and take
appropriate measures to protect the blender
from moisture, dust, and household pests.
Ensure that the power cord is disconnected and
wait until the jar cools down before cleaning.
The table surface the blender is placed on must
be regularly cleaned of grease.
Please rinse the jar's interior and accessories
with clean water before wiping them dry. The
blades are sharp, so please be careful when
cleaning toavoid injury emptying the bow.
Do not use any power supply other than
120V to avoid fire and electrical shocks.
Always unplug the blender by holding the
powerplug to avoid fire or electrical shocks.
Do not plug or unplug the power cord when
your hands are wet to avoid injury and
electrical shocks.
Use only power sockets with a rated current
above 10 A.
Precautions on Electric Power

05
Do not add water over the maximum level, or
else the water will overflow or spray out and
cause burns or other accidents.
Idling or overloading is strictly prohibited.
Do not move the blender or touch any running
parts when in use to avoid accidents.
Do not heat without any food or water inside.
Do not move the lid and lid plug when in use.
Do not allow any liquid to get on the pin
connector.
There will be residual heat after heating
element works.
The surface of the jar and lid will be hot while
heating, so please do not touch them while in
use.
In Use
If the power cord is damaged or broken, it must
be replaced by the manufacturer or after-sales
service department to avoid safety hazards.
Do not use other power cord extenders or parts
not approved by manufacturer or maintenance
department when repairing.
To avoid the risk of fire, do not use low-quality
power strips with this product.
Only use the blender on the base provided.
Always unplug the blender before cleaning,
assembling or disassembling, or after useing.
Make sure that the blender is powered off
before moving the base.

Lid Plug
Lid
Jar
Cold Drink Scale
Hot Drink Scale
Heating Plate
Whisk
Blade
Jar base
Main Base
Control Panel
Product Description
06
Steam and heat may damage, discolor or
deform your walls and furniture, so keep the
product preferably during use 30 cm away from
any walls and furniture.
When using the blender in a kitchen cabinet, etc.,
please ensure that the place is well ventilated.
Environment

About Use
Start to Use
07
Accessories
Whisk x 1 Brush x 1 Measuring Cup x 1
“Timer”Button
Indicator
Main Rotary
Knob/Screen
“Cancel”Button
Jam
30min
Turn ON/OFF and Pause
1. Turn On
Press & hold
to start
Enable Wi-Fi?
Yes No
Tip: The illustrations of product, component and user interface are all schematic diagrams for reference
only in the manual.
Due to possible upgrade of the product, there may be differences between the actual product and the
schematic diagram included herein. The actual product shall prevail.
When joyami Smart Blender is powered on for the first time, it
enters the Wi-Fi setting interface. Press the main rotary knob and
select Enable/Disable Wi-Fi. At this moment, rotate the main rotary
knob to Enable or Disable Wi-Fi, press the main rotary knob to
confirm and return to “Press & hold to start” interface to start the
blender. If no operation is made for 30sec, the default result will be
"No" (Wi-Fi is disabled).
Every time joyami Smart Blender is powered on, the screen will
display “Press & hold to start”. At this moment, press and hold the
main rotary knob for 2 sec to turn on the device. The first mode will
be displayed when joyami Smart Blender is powered on and turned
on for the first time. In the standby state, if no operation is made
for 10min, the screen will enter the Always on Display (AOD) state.

08
In the working state, if the main rotary knob is pressed once,
joyami Smart Blender will pause working; if the main rotary knob is
pressed again, it will resume working as set in the last operation.
3. Pause
01:45
Paused
2. Turn Off
joyami Smart Blender may be turned off after the main rotary knob
is pressed and held for 2sec in any state, except in the Press & hold
to clean mode. In the non-working state (standby, lifting jar, and
opening jar plug), if no operation is made for 10min, the screen will
enter the Always on Display (AOD) state.
Tip: Depending on functions, joyami Smart Blender has different default
pause durations, namely, 2 min for hot drinks and 1 min for cold drinks.
The pause state is in the countdown mode.
Tip: The version of Mi Home app might have been updated, please follow
the instructions based on the current app version.
1. Be careful of scald caused by residual heat. Please wait until the jar fully cools before cleaning.
2.After the drink is made, cools and is poured out, please immediately add clean water in the jar
and operate the "Press & hold to clean" mode for several times to clean the jar better.
3.After powering off joyami Smart Blender, clean the outside surface of the main base with soft
wet cloth. Do not immerse any working electrical components such as the main base, jar, and
power cord in water. Dot not spay water on any part containing electric component such as
the main base and jar base.
4.When cleaning, rinse the jar interior and accessories with clean water, and wipe off residual
water. The blades are very sharp. Be careful with the blades to avoid cuts during cleaning.
5.Do not use abrasive detergent or corrosive liquid (such as gasoline and acetone) to clean the
device.
6.If any part of joyami Smart Blender is strained by fruit/vegetable juice or other drinks, add
several drops of edible oil to wipe the strains before rinsing it with clean water to better
remove the stains. Please wipe off residual water after rinsing any parts with clean water.
7.If any residues in the jar form a hard block that is difficult to remove, please add an appropriate
amount of water to soak it first, and then rinse and wipe it off after it is softened.
8.When the bottom of the heating plate is not clean after several times of cleaning and
accumulated with any residual adhesive layer on it, soak the bottom with clean water for a
period of time, then dip white vinegar with soft cloth, and gently wipe the bottom with the
cloth. Be careful of the blades so as to avoid cuts when wiping them. Do not wipe the device
after it is powered on.
Connect with Mi Home App
Wi-Fi Status
The Wi-Fi icon is blinking
The Wi-Fi icon stays on
Wi-Fi is disabled
Wi-Fi is enabled
Operation Mode Status Display
This product works with Mi Home app. Control your device, and
interact it and other smart home devices with Mi Home app.
Scan the QR code to download and install the app. You will be
directed to the connection setup page if the app is installed already.
Or search "Mi Home" in the app Store to download and install it.
Open Mi Home app, tap "+" on the upper right, and then follow
prompts to add your device.
Tip: When Wi-Fi is disabled, the Wi-Fi icon is in the blinking state.
Operating Guide
1. Take out joyami Smart Blender, clean the lid plug, lid and
whisk with water, and the outside surface of the main base
with soft wet cloth. Do not immerse any working electrical
components such as the main base, jar, and power cord in
water, not spay water on any part containing electric
component such as the main base and jar base.

Cleaning & Maintenance
Cleaning
09
Jam
30min
2. Clean the ingredients, cut them into 3cm chunks and put
the chunks in the jar.
3. Install the lid plug on the lid, turn the lid clockwise and lock
it with the jar tightly.
4. Place the jar correctly on the main base, and align the
small triangle below the handle with the alignment line on
the main base. Make sure to place the main base on a table
surface.
5. After powering on joyami Smart Blender, rotate the main
rotary knob to switch over its functions. When switching to
the required function, press the main rotary knob to enter
the cooking state.
1. Be careful of scald caused by residual heat. Please wait until the jar fully cools before cleaning.
2.After the drink is made, cools and is poured out, please immediately add clean water in the jar
and operate the "Press & hold to clean" mode for several times to clean the jar better.
3.After powering off joyami Smart Blender, clean the outside surface of the main base with soft
wet cloth. Do not immerse any working electrical components such as the main base, jar, and
power cord in water. Dot not spay water on any part containing electric component such as
the main base and jar base.
4.When cleaning, rinse the jar interior and accessories with clean water, and wipe off residual
water. The blades are very sharp. Be careful with the blades to avoid cuts during cleaning.
5.Do not use abrasive detergent or corrosive liquid (such as gasoline and acetone) to clean the
device.
6.If any part of joyami Smart Blender is strained by fruit/vegetable juice or other drinks, add
several drops of edible oil to wipe the strains before rinsing it with clean water to better
remove the stains. Please wipe off residual water after rinsing any parts with clean water.
7.If any residues in the jar form a hard block that is difficult to remove, please add an appropriate
amount of water to soak it first, and then rinse and wipe it off after it is softened.
8.When the bottom of the heating plate is not clean after several times of cleaning and
accumulated with any residual adhesive layer on it, soak the bottom with clean water for a
period of time, then dip white vinegar with soft cloth, and gently wipe the bottom with the
cloth. Be careful of the blades so as to avoid cuts when wiping them. Do not wipe the device
after it is powered on.

Maintenance
10
Press & hold
to clean
Function Instruction
Mode
Jam
Smooth soup
Chunky soup
Soy milk
Operating Method
1. Be careful of scald caused by residual heat. Please wait until the jar fully cools before cleaning.
2.After the drink is made, cools and is poured out, please immediately add clean water in the jar
and operate the "Press & hold to clean" mode for several times to clean the jar better.
3.After powering off joyami Smart Blender, clean the outside surface of the main base with soft
wet cloth. Do not immerse any working electrical components such as the main base, jar, and
power cord in water. Dot not spay water on any part containing electric component such as
the main base and jar base.
4.When cleaning, rinse the jar interior and accessories with clean water, and wipe off residual
water. The blades are very sharp. Be careful with the blades to avoid cuts during cleaning.
5.Do not use abrasive detergent or corrosive liquid (such as gasoline and acetone) to clean the
device.
6.If any part of joyami Smart Blender is strained by fruit/vegetable juice or other drinks, add
several drops of edible oil to wipe the strains before rinsing it with clean water to better
remove the stains. Please wipe off residual water after rinsing any parts with clean water.
7.If any residues in the jar form a hard block that is difficult to remove, please add an appropriate
amount of water to soak it first, and then rinse and wipe it off after it is softened.
8.When the bottom of the heating plate is not clean after several times of cleaning and
accumulated with any residual adhesive layer on it, soak the bottom with clean water for a
period of time, then dip white vinegar with soft cloth, and gently wipe the bottom with the
cloth. Be careful of the blades so as to avoid cuts when wiping them. Do not wipe the device
after it is powered on.
1. joyami Smart Blender should be used frequently to keep its motor dry.
2. If the device is not used for a long time, please keep it in a dry and ventilated place to
prevent the motor from being affected by moisture.
After turning on the device, the main rotary knob displays "Jam". Press the
main rotary knob to start making jam, or rotate the main rotary knob to select
Smooth soup, Chunky soup or Soy milk, press the main rotary to start making
the chosen one.
After turning on the device, the main rotary knob displays "Jam". Rotate the
main rotary knob to select “Smoothie”, “Fruit & vegetable juice” or
“Milkshake”, and press the main rotary knob to start making the chosen drink.
After turning on the device, the main rotary knob displays "Jam". Rotate the
main rotary knob to select the “Press & hold to clean” mode, add the
ingredients or clean water in the jar, press the main rotary knob to start
operating the chosen operation.
Tip 1: You may select a Timer program. joyami Smart Blender will keep warm by
default after the cooking program is completed. If cooking is paused and not
resumed after 2 min during the working period, the cooking program will be
canceled automatically.
Tip 2: After the device starts working, if the main rotary knob is pressed, it will pause
the cooking, and if pressed again, it will resume the cooking. After the cooking is
paused, if the Cancel button is pressed, the device will exit from the cooking.
Tip 1: You are not allowed to select a Timer program. The device will cancel the
cooking program automatically if cooking is paused and not resumed after 1 min
during the working period.
Tip 2: After the device starts working, if the main rotary knob is pressed, it will pause
the operation, and if pressed again, it will resume the operation. After the operation
is paused, if the Cancel button is pressed, the device will exit from the operation.
Smoothie
Fruit &
vegetable
juice
Milkshake
Tip 1: If ingredient is not fully blended, select "Press & hold to clean" function to
blend for a short time again.
Tip 2: Select "Press & hold to clean" function to clean the jar.

11
Recipe
Drink Name Time Ingredient Quantity
Smoothie
Smooth soup
Milkshake
Chunky soup
Jam 30min
1min
45sec
2min
38min
35min
300 g ice cubes (2 cm cube in size)
300 g blueberry,120 g white granulated sugar, 6 g lemon juice
Manual
Settings
1. Be careful of scald caused by residual heat. Please wait until the jar fully cools before cleaning.
2.After the drink is made, cools and is poured out, please immediately add clean water in the jar
and operate the "Press & hold to clean" mode for several times to clean the jar better.
3.After powering off joyami Smart Blender, clean the outside surface of the main base with soft
wet cloth. Do not immerse any working electrical components such as the main base, jar, and
power cord in water. Dot not spay water on any part containing electric component such as
the main base and jar base.
4.When cleaning, rinse the jar interior and accessories with clean water, and wipe off residual
water. The blades are very sharp. Be careful with the blades to avoid cuts during cleaning.
5.Do not use abrasive detergent or corrosive liquid (such as gasoline and acetone) to clean the
device.
6.If any part of joyami Smart Blender is strained by fruit/vegetable juice or other drinks, add
several drops of edible oil to wipe the strains before rinsing it with clean water to better
remove the stains. Please wipe off residual water after rinsing any parts with clean water.
7.If any residues in the jar form a hard block that is difficult to remove, please add an appropriate
amount of water to soak it first, and then rinse and wipe it off after it is softened.
8.When the bottom of the heating plate is not clean after several times of cleaning and
accumulated with any residual adhesive layer on it, soak the bottom with clean water for a
period of time, then dip white vinegar with soft cloth, and gently wipe the bottom with the
cloth. Be careful of the blades so as to avoid cuts when wiping them. Do not wipe the device
after it is powered on.
After turning on joyami Smart Blender, the main rotary knob displays "Jam".
Rotate the main rotary knob to select the “Manual “mode, press the main
rotary knob, and then rotate the main rotary knob to select a revolving speed.
Tip: After the device starts working, if the main rotary knob is pressed, it will pause
the operation, and if pressed again, it will resume the operation. After the operation
is paused, if the Cancel button is pressed, the device will exit from the operation.
1. If Wi-Fi is enabled in joyami Smart Blender, rotate the main rotary knob to
select the Wi-Fi interface on the Settings screen, and press the main rotary
knob to reset or disable Wi-Fi.
2. If Wi-Fi is disabled in joyami Smart Blender, rotate the main rotary knob to
select the Wi-Fi interface on the Settings screen, and press the main rotary
knob to enable Wi-Fi.
1pc potato (about 220 g), 10 g cashew nut, 50 g white
mushroom, 2 g salt, an appropriate amount of white pepper
powder, 720 ml water
1pc potato (about 220g), 10 g cashew nut, 50 g white
mushroom, 2 g salt, an appropriate amount of white pepper
powder, 720 ml water
Tip: During the enabling or disabling Wi-Fi process, if no operation is made for 30
sec, the last option is chosen and back to the Setting interface by default.
640 g carrot, 960 ml water
Tip: When using joyami Smart Blender for continuously making fruit
& vegetable juice, the working time should not exceed 2 min each
time, and the total working time should not exceed 6 min. During the
operation, if the main base is overheated, stop the operation for
about 20 min, and resume it after the main base cools down.
Manual 30sec
For example, for Fruit & vegetable juice, 940 g carrot, 660 ml water
Tip: When using joyami Smart Blender for continuously making fruit
& vegetable juice, the working time should not exceed 2 min each
time, and the total working time should not exceed 6 min. During the
operation, if the main base is overheated, stop the operation for
about 20 min, and resume it after the main base cools down.
Soy milk 35min
Soybeans 70 g (about 100 ml mark on the measuring cup), 3 red
dates and 10 wolfberries with water added to the 1000 ml mark
Note: Only jam, soy milk, smooth soup, and chunky soup are available for
scheduling in advance. Other recipes do not support this function.
Cautions:
Only Jam, Smooth soup, Chunky soup and Soy milk are available for scheduling in advance. Other
recipes do not support this function.
Fruit &
vegetable
juice
1pc red pitaya (about 400 g), 300 ml yoghurt, 5 ice cubes (2 cm
in size), an appropriate amount of honey

Fault Code
Motor overloaded
Exit after placing the jar
Exit after placing the lid
E02
Fault is not repairable
E05
E10
Fault is not repairableE11
Ingredients is not cut fully
Troubleshooting
Fault Phenomenon
Overflow
Burning on the bottom
Troubleshooting
Code
Motor overloadedE01
Place the jar
Place the lid
Overheated
No jar is placed
No lid is placed
Contents
Displayed Meaning Solution
12
Temperature
sensor error
Communication
error
The bottom temperature
sensor gives a high-tem-
perature alarm
The bottom temperature
sensor is open-/short-cir-
cuited
After power off the device, remove
the food in the jar, wait until the
device cools down, then power it
on and start again
The device will resume the program
automatically when the temperature
drops, and at this moment press the
Cancel button to enter the standby
state
Communication is
abnormal between the
power supply board and
the display board
·Add an appropriate amount of ingredients
·Add water until it reaches the correct water level line
·Select a mode as instructed herein
·Contact after-sales service
·Add an appropriate amount of ingredients
·Do not add flour or other ingredients building up and causing
serious burning on the bottom
·Add water until it reaches the correct water level line
·Wash and clean the jar thoroughly before use
·Select a mode as instructed herein
·Contact after-sales service
·Add an appropriate amount of ingredients
·Add water until it reaches the correct water level line
·Select a mode as instructed herein
·Contact after-sales service

Work noise
Basic Parameter
Product Name JDD02MSmart Blender
1600mL
600W
Product Model
Rated Frequency
Blending Power 500W Heating Power
1200mLMax. Hot Drink Capacity
188×222×436mm
Dimensions
Max. Cold Drink Capacity
120V
Rated Voltage 60Hz
13
Food is not hot when the
program is completed
·Select a mode as instructed herein
·Contact after-sales service
The display screen is
not on
·Check whether the power cord is proper and make sure it is
plugged and powered on correctly
·Contact after-sales servic
The display screen is on,
but the device doesn't
work
·Re-select and confirm a mode, and press the screen to start
the device
·Add water until it reaches the correct water level line, wait until
the device cools, and then restart the device
·Unplug the power cord, then plug it again and operate the
steps as normal
·Contact after-sales service
·Blending sound from the motor is a normal
phenomenon
·Contact after-sales service
Tip 1: Check whether the power supply is connected properly and whether the jar and lid are installed in
place. In case of an abnormal situation such as abnormal noise, smell, and smoke, immediately power off
and stop the device.
Tip 2: If the device does not work properly even after the inspections above, please contact after-sales
service.
Please visit the official website at https://www.joyami.com,if you need after-sales service or other
information, or encounter any problem.
After-sale Service

User Manual Version: V0.6
14
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.

15
Maunfacturer：Chunmi Technology (Shanghai) Co., Ltd.
Address：Building 11, 1333 Jiangnan Avenue, Changxing Science and Technology Park, Lingang,
201203 Shanghai, PEOPLE'S REPUBLIC OF CHINA

Mode d'utilisation joyami Smart Blender
Avant d'utiliser le joyami Smart Blender, lisez attentivement ce mode d'utilisation
et le conservez bien pour consultation au futur.
Le joyami Smart Blender est destiné à un usage domestique.

17
Consignes
Respecter les consignes de sécurité fondamentales
quand vous utilisez l'appareil, notamment :
·Lire toutes les instructions de l'utilisation.
·
Jamais mettre le cordon d'alimentation, la prise
ou l'appareil potable dans l'eau ou d'autres
liquides pour éviter le choc d'électricité.
·
Ne pas laisser les personnes qui ne n'ont pas
capacité physique, mentale ou manquent de
connaissances générales (y compris les
enfants) utiliser le produit sans surveillance ou
guide. Sauf ils sont accompagnés avec leur
tuteur sous surveillance ou guide pour assurer
la sécurité. il faut prêter une grande attention si
le produit est opéré par un enfant ou s'opère à
proximité des enfants. Ce produit n'est pas un
jouet, il faut faire attention.
·
Veuillez éteindre le produit et débrancher le
cordon d'alimentation à partir de la prise si
vous n'utilisez pas le produit ou avant de
démonter ou de nettoyer le produit. Veuillez
saisir étroitement la prise pour le débrancher.
Ne pas tirer forcément le cordon d'alimentation.
·
Ne pas toucher les composants en mouvement.
·
Ne pas opérer l'appareil électrique si le cordon
d'alimentation ou la prise est endommagé ou si
l'appareil est en panne, hors de la tension ou
endommagé. Pour les informations concernant
la vérification, la maintenance ou la modifica-
tion, veuillez appeler le service de clientèle
pour contacter le fabricant.
·
Jamais utiliser les accessoires non recommandés
par le fabricant (y compris la bouteille en
conserve), il risque de causer les blessures
physiques.

·Utilisation à l'intérieur seulement. Ce produit est
destiné à l'usage domestique.
·
Ne pas suspendre le cordon d'alimentation aux
bords de la table ou du plan ni entrer en contact
avec une surface surchauffée.
·
Ne pas placer le produit sur la vapeur surchauffée
ou le four électrique ou à proximité de la chaleur
ou dans le four électrique chauffant.
·
Ne pas laisser contacter les mains avec les
conteneurs au cours du mélange, pour éviter
toute blessure grave ou le dommage de la
machine. La spatule est seulement utilisée
quand le dispositif ne fonctionne pas (à l'exclu-
sion de la spatule conforme fournie avec le
dispositif)
·Les lames sont tranchantes, opérer avec soin.
·
Fermer bien le couvercle avant d'opérer le
produit.
·
Enlever la partie au milieu du couvercle de deux
pièces quand vous traitez le liquide chaud ou
au cours du fonctionnement chauffé.
·
Refroidir le produit avant de monter ou démonter
les composants ou de nettoyer le produit.
·
Ne pas toucher la surface éventuellement
chaude. Utiliser la poignée ou levier fourni.
·
Veuillez débrancher le cordon d'alimentation à
partir de la prise si vous n'utilisez pas le produit
ou avant de démonter ou de nettoyer le produit.
Refroidir le produit avant de prendre ou de
remettre le produit.
·
Soyez prudent quand vous manipulez un appareil
contenant de l'huile chaude ou le liquide chaud.
18

19
·Vérifier le plus que possible l'interrupteur de
commande est sur OFF ou non avant d'insérer
la prise avec le produit et d'insérer le produit
dans la douille. Pour déconnecter le produit,
ajuster l'interrupteur sur OFF et tirer la prise de
la douille.
·
Ne pas utiliser le produit à d'autres fins.
·
Ne pas toucher les composants en mouvement.