JRC NKG-94 User manual

INSTRUCTIONINSTRUCTION
MANUALMANUAL
PRINTERPRINTER
NKGNKG-9494

i
PREFACE
Thank you for purchasing the NKG-94 JRC Printer.
The JRC Printer can receive and prints out data from a GPS navigator.
●Before using the printer, carefully read this INSTRUCTION MANUAL so as to fully
understand the proper usage and handling.
●If you are uncertain about any operations of the printer or encounter any problems during
operation, refer to this manual. You will find solutions to common problems and useful hints
and suggestions.

ii
Before Operation
Alert Symbols
A number of alert symbols are used in this manual and labeled on the product itself to ensure
safe and proper usage, and to prevent possible injury to you or others and to avoid possible
property damage during operation or maintenance. Some of these alert symbols and their
meanings are shown below. Please understand them before reading this manual:
Indicates a situation that could result in death or
serious personal injury if ignored or if the product is
mishandled.
Indicates a situation that could result in personal injury
and/or property damage if ignored or if the product is
mishandled.
Examples of alert symbols
The triangular symbol (△) means“caution”(danger and/or other warning).
The specific type of hazard (not specified in this example) is depicted in the
warning box.℉
This symbol signifies an action that is prohibited. The specific type of
prohibited action (in this example, disassembly) is depicted in or near the
symbol.
●This symbol signifies a required action. The specific type of required action
(in this example, removing the power plug from the outlet) is depicted in the
symbol.
WARNING
CAUTION

iii
Operating Precautions
Do not disassemble or customize this equipment.
Fire, electrical shock, and/or malfunction can be caused.
Do not get this equipment wet or spill any liquids on or near this equipment.
Electrical shock, and/or malfunction can be caused.
Do not use voltage other than that specified.
Fire, electrical shock, and/or malfunction can be caused.
Do not open the equipment to inspect or repair internal circuits.
Inspection or repairs by anyone other than a specialized technician may
result in fire, electrical shock, or malfunction. If internal inspection or repair is
necessary, contact our service center or agents.
WARNING

iv
Operating Precautions
Do not use this equipment anyplace other than specified clause 8.2.
It may cause injury, failure or malfunction.
Do not install the equipment in a place near water, oil, or the medicine, etc.
which might splash.
It may cause injury, failure or malfunction.
Do not use this equipment anyplace other than specified clause 8.2.
It may cause injury, failure or malfunction.
Do not install the equipment in a place of terrific vibration or shock condition.
It may cause injury, failure or malfunction if it falls.
Do not place heavy objects on the printer.
It may cause injury, failure or malfunction.
Do not install this equipment other than our service center or agents.
It may cause failure or malfunction.
Avoid exposure to direct sunlight, heat, extremely high or low temperature,
corrosive gas, moisture, dust or terrific vibration. It may cause fire,
malfunction, and/or deterioration of print-out quality.
Always use the JRC- designated printer paper (7ZPJD0384). The use of any other
paper may cause printer trouble and/or deterioration of print-out quality.
Do not wire the cable bended with acute angle, twist ,stress, etc.
It may cause fire, injury or electrical shock with the cable crack or the cable
sheath inside damage.
The thermal head of the printer may be very hot after printing. Do not touch the
thermal head of the printer. Make sure the thermal head is cool before replacing
the paper or so.
When cleaning, do not use benzene, alcohol, thinner, or other volatile
solvents. The coated surface may deteriorate or be damaged. Wipe the
surface lightly with a soft cloth.
Use only MF51NR 250V 3.15 fuses. The use of other fuse may cause fire
and/or damage.
CAUTION

v
Operating Precautions
Do not place heavy objects on the printer. Failure to observe this warning may
result in the unit becoming unbalanced and thus causing injury if it falls.
Do not put a heavy thing on the power and data cables. Fire, electrical shock,
and failure may be caused.
Do not get inside of this printer wet.
It may cause failure, malfunction, and/or deterioration of print-out quality.
If an unusual smell, smoke, or other abnormality is detected, immediately turn
off the power to the printer and then turn off the power on the power distribution
panel of the vessel. After confirming that the unusual smell, smoke, or other
abnormality has cleared up, consult your dealer or nearest JRC service/sales
representative for repair. Using the receiver in such situation may cause fire
and/or electrical shock.
Be careful not to cut your hand with the paper cutter of the printer, and then
replace the printer paper. Injury may be cause.
The power switch on the power distribution panel is turned off, when removing
the maintenance cover. Failure to observe this warning may cause electrical
shock and/or malfunction.
When installing, fix the bracket steadily on a hard wood-board with the
JRC-designated screws. If not, it may fall and result in personal injury and/or
damage or of the printer or other things.
When installing on the overhead or wall, it secure tolerable intensity of the weight,
the force of maintaining check and replacing the printer paper. If not, it may fall and
result in personal injury and/or damage or of the printer or other things.
The power switch on the power distribution panel is turned off during replacing
a fuse. When replacing a fuse, use extreme caution not to bring it into contact
with adjacent ones. Short-circuiting due to making contact may cause power
and/or circuit board damage.
The power switch on the power distribution panel is turned off, when removing
the front panel. Failure to observe this warning may cause electrical shock
and/or malfunction.
The power switch on the power distribution panel is turned off, when replacing
the printer unit. Failure to observe this warning may cause electrical shock
and/or malfunction.
CAUTION

vi
EQUIPMENT APPEARANCE
●NKG-94 Printer
単位：mm
(Unit: mm)
Bod
y
Bracket

Contents
PREFACE............................................................................................................ i
Before Operation .............................................................................................. ii
Operating Precautions .................................................................................... iii
EQUIPMENT APPEARANCE ........................................................................... vi
1. Equipment Overview.................................................................................1-1
1.1 Functions.............................................................................................1-1
1.2 Features...............................................................................................1-1
1.3 Configuration ......................................................................................1-2
1.4 Structure..............................................................................................1-3
1.5 Schematic Diagram.............................................................................1-4
2. Names and Functions of Components....................................................2-1
2.1 Front Panel ..........................................................................................2-1
3. Printer Operations.....................................................................................3-1
3.1 Turning Power On ...............................................................................3-1
3.2 Turning Power Off...............................................................................3-1
3.3 Loading Printer Paper ........................................................................3-2
3.4 Feeding the Printer Paper ..................................................................3-3
3.5 Printing ................................................................................................3-3
3.5.1 Printing periodically .................................................................................... 3-3
3.5.2 Printing at arbitrary time ............................................................................. 3-3
3.5.3 Printing example .......................................................................................... 3-4
3.5.4 Printing items and data in use .................................................................... 3-4
3.6 Printing Test ........................................................................................3-5
4. Maintenance and Inspection ....................................................................4-1
4.1 General Maintenance and Check Items ............................................4-1
4.2 Fuse Replacement ..............................................................................4-2
4.2.1 Removing maintenance cover (for preparation work) .............................. 4-2
4.2.2 Replacing fuses ........................................................................................... 4-3
4.3 Printer Unit Replacing Procedure......................................................4-4
4.3.1 Removing front panel unit (for preparation work)..................................... 4-4
4.3.2 Replacing printer unit.................................................................................. 4-5
4.4 Maintenance Parts ..............................................................................4-6
4.5 Trouble Shooting ................................................................................4-6
5. Installation .................................................................................................5-1
5.1 Installation Procedure ........................................................................5-1
5.1.1 Desk mounting type installation procedure .............................................. 5-1
5.1.2 Flush mounting type installation procedure ............................................. 5-2
5.2 Rear Panel ...........................................................................................5-4
5.3 Cable Connection ...............................................................................5-5
5.4 Cable Handling....................................................................................5-6
5.5 Function Setting..................................................................................5-7
5.6 System Configuration.........................................................................5-8
6. After-Sales Service....................................................................................6-1
6.1 Warranty ..............................................................................................6-1
6.2 Stock Periods of Maintenance Parts .................................................6-1
6.3 When Requesting Repair....................................................................6-1

6.4 Optional Maintenance Checks ...........................................................6-1
7. Disposal .....................................................................................................7-1
7.1 Disposal of This Equipment...............................................................7-1
8. Specifications............................................................................................8-1
8.1 General Specification .........................................................................8-1
8.2 Environmental Specification..............................................................8-1
8.3 External Interface................................................................................8-1
8.4 Mechanical Specifications .................................................................8-2
8.4.1 Mechanical details of desk mounting type ................................................ 8-2
8.4.2 Mechanical details of flush mounting type................................................ 8-3
8.4.3 Mechanical parts list.................................................................................... 8-4