JRC INMARSAT FleetBroadband FB250 User manual

INMARSAT FleetBroadband FB250INMARSAT FleetBroadband FB250
Maritime Satellite Communication TerminalMaritime Satellite Communication Terminal
OPERATIONOPERATION
MANUALMANUAL
JUE-250JUE-250

ABOUT YOUR SAFETY
CAUTIONS AGAINST HIGH VOLTAGE
Radio and radar devices are operated by high voltages of anywhere from a few hundred volts up to
many hundreds of thousands of volts. Although there is no danger with normal use, it is very
dangerous if contact is made with the internal parts of these devices. (Only specialists should attempt
any maintenance, troubleshooting, or adjustments.)
There is a very high risk of death by even a few thousand volts, in some cases you can be fatally
electrocuted by just a few hundred volts. To circumvent accidents, you should avoid contact with the
internal parts of these devices at all costs. If contact is inevitable as in the case of emergency, you
must switch off the devices and ground a terminal in order to discharge the capacitors. After making
certain that all the electricity is discharged, only then can you insert your hand into the device.
Wearing cotton gloves and putting your free hand in your pocket, in order not to use both hands
simultaneously, is also a very good method of shock prevention. Quite often, an injury occurs by
secondary factors, therefore it is necessary to choose a sturdy and level working surface. If someone
is electrocuted it is necessary to thoroughly disinfect the affected area and seek medical attention as
soon as possible.
CAUTIONS CONCERNING TREATMENT OF
ELECTROCUTION VICTIMS
When you find an electrocution victim, you must first switch off the machinery and ground all circuits.
If you are unable to cut off the machinery, move the victim away from it using a non-conductive
material such as dry boards or clothing.
When someone is electrocuted, and the electrical current reaches the breathing synapses of the central
nervous system inside the brain, breathing stops. If the victim’s condition is stable, he or she can be
administered artificial respiration. An electrocution victim becomes very pale, and their pulse can be
very weak or even stop, consequently losing consciousness and becoming stiff. Administration of
first aid is critical in this situation.

FIRST AID
☆Note points for first aid
Unless there is impending danger leave the victim where he or she is, then begin artificial respiration.
Once you begin artificial respiration, you must continue without losing rhythm.
(1) Make contacts with the victim cautiously, there is a risk that you may get electrocuted.
(2) Switch off the machinery and then move the victim away slowly if you must.
(3) Inform someone immediately (a hospital or doctor, dial emergency numbers, etc.).
(4) Lay the victim on his or her back and loosen any constructive clothing (a tie, or belt).
(5) (a) Check the victim’s pulse.
(b) Check for a heartbeat by pressing your ear against the victim’s chest.
(c) Check if the victim is breathing by putting the back of your hand or face near the
victim’s face.
(d) Check the pupils of the eyes.
(6) Open the victim’s mouth and remove any artificial dentifrice, food or chewing gum. Leave
the mouth opened and flatten the tongue with a towel or by putting something into the mouth
to prevent the victim’s tongue from obstructing the throat (If he or she is clenching their teeth
and it is difficult to open the mouth, use a spoon or the like to pry open the mouth).
(7) Continually wipe the mouth to prevent the accumulation of saliva.

☆If the victim has a pulse but is not breathing
(1)Place the victim’s head facing backward (place something under the neck like a pillow).
(2)Point the chin upward to widen the trachea.
(3)Pinch the victim’s nose, take a deep breath, then put your mouth over the victim’s mouth and exhale
completely, making sure that your mouth completely covers the victim’s mouth. Then remove
your mouth. Repeat this routine 10 to 15 times per minute (holding the nostrils).
(4)Pay attention to the victim to notice if he or she starts to breath. If breathing returns, stop
resuscitation.
(5)If it is impossible to open the victim’s mouth, put something like a plastic straw or vinyl tube into
one of the nostrils then blow air in while covering the mouth and the other nostril.
(6)Occasionally, when the victim comes back to consciousness, they immediately try to stand up.
Prevent this and keep them in a laying position. Give them something warm to drink and be sure
that they rest (do not give them any alcohol).
Administering artificial respiration by raising the head.
1 Raise the back of head, and then
place one hand on the forehead and place
the other hand under the neck. (1)
Most victims open their mouth when
doing this, making “mouth to mouth”
resuscitation easier.
2Cover the victim’s mouth by opening
your mouth widely, then push your cheek
against the victim’s nose, (2) or pinch the
victim’s nose to prevent air from leaking
out of it. (3)
3 Completely exhale into the lungs.
Exhale into the lungs until the chest is
inflated.
You have to blow as rapidly as possible
the first 10 times.
“Mouth to mouth” artificial respiration
Figure 1

☆If the victim has no pulse and is not breathing
If the victim has no pulse, his or her pupils are dilated, and if you cannot detect a heartbeat, the heart
may have stopped; beginning artificial respiration is critical.
(1) Put both hands on the diaphragm, with hands on top it and keeping both arms straight each other (If
your elbows are bent; you cannot push with as much power). Press the diaphragm with your body
weight until the chest sinks about 2 cm (about 50 times per minute).
(2) If administering first aid when alone:
Perform the heart massage about 15 times then administer artificial respiration by blowing in twice.
Repeat this routine.
If administering first aid with two people:
One person performs the heart massage 15 times, and the other person blows air in twice. Repeat this
routine (Heart massage and “mouth to mouth” resuscitation used together).
(3) Constantly check the pupils and the pulse, if the pupils become normal and the pulse steadies, keep
him in a laying position and give him something warm to drink, be sure that he rests (do not give him
any alcohol). In any case you have to entrust any major decision making to a doctor. Having
understanding people around is essential to the victim’s recovery from the mental shock of
electrocution.
1 2
3 4
Figure 2 Heart massage in combination with artificial respiration.

i
PREFACE
Thank you for purchasing the JRC Inmarsat FleetBroadband Mobile Earth Station, the JUE-250.
The JUE-250 is an Inmarsat digital satellite communication terminal for Voice (4kbps Speech),and
Audio (64kbps 3.1kHz Audio), maximum 284kbps Standard IP service, 8kbps, 16kbps, 32kbps, 64kbps,
or 128kbps Streaming IP service, and Short Messaging Service (SMS).
The JUE-250 is packaged and shipped under strict quality control with inspection criteria to deliver the
equipment with highest quality, performance, and reliability needed to meet our customer’s
requirements and satisfaction.
JRC believes that you will use this equipment satisfactorily for a long time.
•Please read this manual carefully and carry out proper operation.
•Please do not lose this useful manual, as you will have to refer to it from time to time.

ii
BEFORE OPERATION
(1) About this operation manual
Before operating this equipment, read the manual carefully to ensure correct operation.
This book is useful for troubleshooting, too.
(2) Concerning the symbols
This manual uses the following symbols to explain the correct operation and to help prevent
injury or damage to property.
The symbols and descriptions are as follows. Understand them before proceeding with this
manual.
Indicates danger that, if ignored, will
result in serious injury or even death.
Indicates warning that, if ignored,
may result in serious injury or even
death.
Indicates caution that, if ignored,
may result in injury or damage to
property.
Examples of symbols
The symbol indicates caution (including DANGER and WARNING).
The illustration inside the symbol specifies the content of the caution
more accurately. (This example warns of possible electrical shock.)
The symbol indicates that performing an action is prohibited.
The illustration inside the symbol specifies the content of the prohibited
operation. (In this example disassembly is prohibited.)
The ●symbol indicates operations that must be performed.
The illustration inside the ●symbol specifies obligatory instructions. (In
this example unplugging is obligatory.)
(3) Concerning warning labels
Warning labels are posted on the equipment.
Do not remove, damage or modify.
* Windows Internet Explorer is a registered trademark of Microsoft Corporation.
Netscape Navigator is a registered trademark of Netscape Communications Corporation.
DANGER
WARNING
CAUTION

iii
About Warning Label
Below mentioned warning labels are put on the JUE-250, ADE and BDE.
Do not take off, destroy, or modify these labels.
<Warning Label of ADE >
<Warning Label of BDE >
Notes
1) IMEI 35887701
International Mobile Equipment Identity (IMEI) is an unique number used to identify an individual
mobile equipment to a GSM or UMTS network.
2)
Attestation number which means safe, high-quality product and suits EU instruction (Free circulation
was permitted in the EU signatory).
Note 1)
Note 2)

iv
BEFORE USING
•JRC is indemnified for any damages from incorrect operation, malfunction, and other
troubles except as outlined in the product warranty and by limitation of law.
•Some functions depend on the hardware and software version of your terminal equipment
connected with your JUE-250. Confirm your terminal equipment, hardware, and software
versions before contacting the purchasing dealer.
•Your communication data are transmitted via the Inmarsat systems, therefore, there is a
possibility that some errors may occur.
We strongly recommend important data be backed up to ensure safety and protection from loss.
Usually, digital scrambling of the Inmarsat system protects your communication data privacy.
However we caution you to understand that your communication data might be intercepted by
special technology and unauthorized access to the communication theory.
There are some additional and optional functions of the JUE-250 that shall be released in the
near future for evaluation.
•Specifications of the JUE-250 and its accessories may change without notice, for
improvement.

v
DANGER
WARNING
DURING OPERATION
Do not touch any internal parts with your hands or tools.
It may cause fire, electrical shock or malfunction.
DURING OPERATION
Please do not bring the power supply code close to the heat apparatus. The coating of
the code may relieved, and it causes a fire and the electric shock.
Do not approach the ADE while transmitting, It transmits microwave and strong
microwave may cause injury.
If an external matter, such as metal fragments, water, liquid, etc., infringes into
your JUE-250, turn off the power and contact to the purchasing dealer.
Continuous operation may cause fire, electrical shock or malfunction.
Install the JUE-250 correctly in accordance with the installation manual.
Inappropriate installation may cause incorrect operation; fire, electrical shock,
or malfunction.
Lay ADE-BDE coaxial cable correctly in accordance with the Installation
manual. (Especially waterproof should be treated correctly in accordance
with the installation manual.) Pay particular attention to waterproof
following the instruction of installation manual. Inappropriate installation
may cause incorrect operation, fire, electric shock or malfunction.
Use the specified power supply voltage only （+19VDC to +31VDC）, otherwise
trouble, fire, or electric shock or malfunction may occur.
Do not troubleshoot or repair the internal equipment of the JUE-250 by yourself.
Any electrical work by any person other than our trained maintenance staff may
cause fire or abnormal operation of this equipment or electrical shock for you.
This equipment meets the technical standard of the Ministry of Internal affairs and
Communications.

vi
CAUTION
WARNING
Do not troubleshoot or repair the internal equipment of the JUE-250 by yourself.
Any electrical work by any person other than our trained maintenance staff may
cause fire or abnormal operation of this equipment or electrical shock for you.
This equipment meets the technical standard of the Ministry of Internal affairs and
Communications.
Do not remove, destroy, or modify warning labels.
DURING OPERATION
Before using, read this operation manual.
Incorrect operation may cause improper working operation or malfunction.
<<Above Deck Equipment>>
Do not deliver mechanical shock and/or force, because each unit of your ADE is a
precision instrument. Unwanted shock and force may cause malfunction.
Do not paint the radome. Painting of the radome may cause a decrease of the
communication quality.
<<Below Deck Equipment>>
Do not turn off the power switch of BDE except the case that maintenance or
checking is required.
It may cause malfunction of the antenna drive and may cause troubles.
Do not turn off the POWER switch during sailing. Malfunction of the antenna
drive and other troubles may results.
Do not mount the Handset near CRT device or other devices; otherwise
performance of the devices may be affected by the Handset’s magnetic field.
Do not set/remove the SIM card during power switch is turned on.

1. The Inmarsat Communication Systems
2. Introduction of the JUE-250
3. Appearance
4. Getting Started
5. How to use the Telephone / FAX
6. PC connection and LaunchPad calling
7. Using Audio port
8. Handset Menu System
9. Maintenance
10. After-sales service
11. Specification
1
2
3
4
5
6
7
8
9
10
11
APPENDIX

Inmarsat FleetBroadband JUE-250 Operation Manual
Contents
PREFACE ........................................................................................................... i
BEFORE OPERATION ..................................................................................... ii
BEFORE USING.............................................................................................. iv
DURING OPERATION..................................................................................... v
1. The Inmarsat Service systems..................................................................... 1
1.1 Outline....................................................................................................... 1
1.1.1 Coverage area......................................................................................... 1
1.1.2 The Inmarsat FleetBroadband service ................................................... 2
1.2 The Inmarsat Fleet Broadband FB250 services explanations................... 4
1.3 Important reminder for using JUE-250..................................................... 4
2. Introduction of the JUE-250 ....................................................................... 5
2.1 Outline....................................................................................................... 5
2.2 Features..................................................................................................... 5
2.3 Cable connection system diagram and components List ........................ 6
2.3.1 Cable connection system diagram ......................................................... 6
2.3.2 Components list ................................................................................... 7
2.4 Dimensional drawing (JUE-250 standard components) ........................... 8
2.4.1 ADE (Above Deck Equipment)[GSC-451] ........................................... 8
2.4.2 BDE (Below Deck Equipment)[GSC-452]............................................ 9
2.4.3 Handset [NQW-267] .......................................................................... 10
2.4.4 Coaxial cable [CFQ-5924A3].............................................................. 11
3. Appearance ............................................................................................... 13
3.1 ADE ........................................................................................................ 13
3.2 BDE......................................................................................................... 14
3.3 ADE—BDE connecting cable .............................................................. 17
3.4 Handset ................................................................................................... 18
3.4.1 LCD/LED section ................................................................................ 19
3.4.2 Functional section ................................................................................ 24
3.4.3 Alpha-Numeric section ........................................................................ 24
3.5 Communication terminals....................................................................... 25
3.5.1 Terminal requirements ......................................................................... 25
3.5.2 Usage environment .............................................................................. 26
3.6 Handset menu.......................................................................................... 26

4. Getting started........................................................................................... 27
4.1 Connecting terminals and power on ....................................................... 28
4.1.1 Connecting terminals with cables ........................................................ 28
4.1.2 Setting/removing SIM card.................................................................. 30
4.1.3 Power ON............................................................................................. 31
4.1.4 Screen display of Handset................................................................... .33
4.2 Initial setting for communication .......................................................... 35
4.2.1 Mode setting of GUEST and ADMIN ................................................. 36
4.2.2 Setting service type (ADMIN user only)............................................. 37
4.2.3 Satellite display.................................................................................... 38
5. How to use the telephone/FAX................................................................. 39
5.1 Handset ................................................................................................... 42
5.1.1 Making a call/Answering the phone .................................................... 42
5.1.2 Using Phone Book (Speed dial)........................................................... 43
5.1.3 Using Redial menu............................................................................... 44
5.1.4 Adjusting voice volume, screen brightness, and ringer volume .......... 45
5.1.5 Adjusting ringer volume and pattern, and voice volume..................... 46
5.1.6 Holding on the line............................................................................... 48
5.1.7 Forwarding a call from Handset to terminal telephone ....................... 49
5.1.8 Using a Secret Code............................................................................. 50
5.1.9 Entry, change and deletion of Phone Book .................................... 52
5.1.10 Displaying Call Log........................................................................... 55
5.2 Using telephone/FAX with TEL1/2 port................................................. 57
6. PC connection and LaunchPad calling ..................................................... 59
6.1 USB port PC connection......................................................................... 60
6.1.1 Driver Installation to your PC................................................................. 60
6.1.2 Connecting USB ports ............................................................................ 64
6.2 Ethernet port PC connection ................................................................... 66
6.3 Connecting to Internet using LaunchPad................................................ 68
6.3.1 Standard IP........................................................................................... 68
6.3.2 Streaming IP......................................................................................... 71
6.3.3 SMS...................................................................................................... 74
6.3.3.1 Sending SMS .................................................................................... 74
7. Using Audio port....................................................................................... 75
8. Handset Menu System .............................................................................. 79
Top menu ................................................................................................. 80

8.1. Status menu............................................................................................ 81
8.1.1 RX (Reception) menu .......................................................................... 82
8.1.2 TX (Transmission) menu ..................................................................... 82
8.1.3 Position status display.......................................................................... 83
8.1.4 Product menu ....................................................................................... 84
8.1.5 Unit Info menu..................................................................................... 85
8.1.6 ID menu ............................................................................................... 88
8.2 SMS menu............................................................................................... 89
8.2.1 New MSG menu . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .9 91 1
8.2.2 Inbox menu .......................................................................................... 93
8.2.3 Sent menu............................................................................................. 94
8.2.4 Draft menu ........................................................................................... 95
8.2.5 Setting menu ........................................................................................ 96
8.3 Satellite menu.......................................................................................... 97
8.3.1 Satellite display.................................................................................... 97
8.3.2 Spot Beam ID display .......................................................................... 97
8.4 Phone Book (Speed dial) menu............................................................... 98
8.4.1 Editing the Phone Book address .......................................................... 99
8.5 Redial menu .......................................................................................... 100
8.6 Call Log (Communication history) menu............................................. 101
8.6.1 Call Log list menu.............................................................................. 102
8.6.2 Call Log authentication and deletion ................................................. 103
8.7 Self Test menu....................................................................................... 103
8.8 Alarm Pack menu ................................................................................ 104
8.8.1 Unit selection menu for Alarm Pack.................................................. 105
8.9 ADMIN menu ....................................................................................... 107
8.9.1 Setup menu......................................................................................... 108
8.9.1.1 Delivery setting............................................................................... 109
8.9.1.2 Local Time setting ......................................................................... 110
8.9.1.3 LED setting ......................................................................................111
8.9.1.4 Tracking setting................................................................................111
8.9.2 Port Cont menu .................................................................................. 112
8.9.2.1 Port Cont setting item selection menu ............................................ 113
8.9.3 Port menu ........................................................................................... 114
8.9.3.1 Handset advanced setting menu...................................................... 115
8.9.3.2 ISDN MSN setting menu................................................................ 116
8.9.3.3 Ethernet setting menu ..................................................................... 117
8.9.4 User Reg. menu.................................................................................. 118
8.9.4.1 User Reg. operation selecting menu ............................................... 119
8.9.5 Auto DCN. (Auto disconnection) menu ............................................ 120

8.9.5.1 Max Time menu .............................................................................. 123
8.9.6 SIM menu........................................................................................... 124
8.9.6.1 Chg PIN1menu................................................................................ 125
8.9.6.2 PIN Input setting ........................................................................... 127
8.10 Other screen ........................................................................................ 128
9 Maintenance............................................................................................. 129
9.1 Daily maintenance ................................................................................ 129
9.2 Self test.................................................................................................. 130
10. After-sales service................................................................................. 131
11. Specification.......................................................................................... 133
（APPENDIX）
A Changing Procedures of using GYRO tracking...................................... 135
B Handset menu tree................................................................................... 141
C JUE-250 software updating procedure.................................................... 145
D FB LaunchPad Installation Procedure..................................................... 157
E TCP Accelerator Installation Procedure .................................................. 168
F Default value list...................................................................................... 175
G Trouble shooting and FAQ(TBD) ........................................................... 176
H Cause Code ............................................................................................. 185
I Glossary.................................................................................................... 188
JRC Network.................................................................................................. 193
Declaration on toxic & Hazardous substances or elements of Electronic
Information Products ..................................................................................... 194

1. Inmarsat Service systems
1
Chapter1 The Inmarsat Service Systems
1. Inmarsat Service systems
1.1 Outline
1.1.1 Coverage area
The Inmarsat Satellites cover the earth’s surface except at the high latitude areas near the North
Pole and the South Pole.
Inmarsat terminals are available for any type of vehicle or ship, and are capable of communicating
day and night.
The Inmarsat coverage map displays the area of three satellite regions.
•Europe, Middle East, Africa (EMEA) Ocean Region
•Asia-Pacific (APAC) Ocean Region
•America (Americas (AMER))Ocean Region
Overlap Ocean Region
Fig.1.1.1 The coverage areas of Ocean Region (after Feb.28, 2009)
Europe, Middle
East, and Africa
Ocean Region
Asia, and Pacific
Ocean Region
America Ocean
Region

1. Inmarsat Service systems
2
1.1.2 The Inmarsat FleetBroadband Service
The Inmarsat network system consists of NCS, NOC, SCC, TT&C, and SAS.
Functions of each facility are as follows:
1) Network Coordination Station (NCS)
The NCS is designed for each Inmarsat service (i.e. Inmarsat-A, B, C) in each ocean region, which
manages and coordinates the traffic in the region. The NCS assigns communication channels
between the Mobile Earth Stations (MES) and Satellite Access Station (SAS).
2) Network Operation Center (NOC)
The NOC located at the INMARSAT headquarters in London U.K., coordinates communication
lines of the network 24 hours a day, 365 days a year. The NOC maintains contact via dedicated
satellite and terrestrial links with the NCSs and SASs in all Ocean regions.
The NOC performs the following:
・Coordination with the Satellite Control Center (SCC) for operation of satellites.
・Coordination with NCS and/or SAS for system operation.
・Collection of any status data in operation .
・Coordination of any test of satellite’s performance.
3) Satellite Control Center (SCC)
The SCC controls the positioning of the satellites above the equator.
4) Tracking Telemetry and Control Center (TT&C)
The TT&C supplies data on the status of the Inmarsat satellites to SCC.