JRI Nano SPY LINK Ethernet User manual

USER GUIDE
Nano SPY
LINK Ethernet / WiFi
Ref : 11817D

©JRI 2
TABLE OF CONTENTS
I. INTRODUCTION ........................................................................................................................................ 3
a) Product contents .......................................................................................................................................................3
b) Symbols......................................................................................................................................................................3
II. INSTALLATION RECOMMANDATIONS .............................................................................................................. 3
a) Sources of disturbances or attenuation ....................................................................................................................3
b) Positioning .................................................................................................................................................................4
III. PRESENTATION ........................................................................................................................................ 4
a) Control unit................................................................................................................................................................4
b) Connection.................................................................................................................................................................4
c) Mounting ...................................................................................................................................................................5
d) Locking .......................................................................................................................................................................5
e) Description of the indicator lights .............................................................................................................................5
IV. CONFIGURATION OF NANO SPY LINK ........................................................................................................... 6
a) Operating principle....................................................................................................................................................6
b) Configuration .............................................................................................................................................................6
V. CONFIGURATION OF NANO SPY LINK WIFI............................................................................................ 6
a) Operating principle....................................................................................................................................................6
b) Configuration .............................................................................................................................................................6
VI. USE ...................................................................................................................................................... 7
a) Taking in charge of alarms.........................................................................................................................................7
VII. CHARACTERISTICS ..................................................................................................................................... 7
VIII. MAINTENANCE ........................................................................................................................................ 8
IX. GUARANTY ............................................................................................................................................. 8
X. MAINTENANCE CONTRACT .......................................................................................................................... 8
XI. PROTECTION OF THE ENVIRONNEMENT ........................................................................................................... 9

©JRI 3
I. INTRODUCTION
The Nano SPY LINK is a gateway allowing transmission of information from the Nano SPY to the MySirius cloud
via Ethernet or WiFi networks.
a) Product contents
1 Nano SPY LINK
1 User guide
1 USB cable
b) Symbols
Do not use the device under conditions other than those described in the technical
characteristics
Risk of fire or explosion in the case of improper use:
- Recharging of the battery
- Short circuiting of the battery
If the device is used in a manner not specified by the manufacturer, the protection
provided by the device may be compromised.
II. INSTALLATION RECOMMANDATIONS
The Nano SPY LINK is a gateway allowing transmission of information from the The Nano SPY LINK is a gateway
allowing transmission of information from the Nano SPY to the MySirius cloud via Ethernet or WiFi networks.
To ensure optimal radio transmission, a certain number of recommendations must be respected, as any
wireless transmission is subject to disturbances.
a) Sources of disturbances or attenuation
The presence of obstacles in the wave path between the Nano SPY and the Nano SPY Link (wall,
furniture, people…) or near the antenna.
The thickness of an obstacle in the wave path. The attenuation is greater diagonally than
perpendicularly.
RECYCLING: do not dispose of in a refuse dump or waste disposal bin. Comply with existing legislation for disposal.
Power source: this device is powered by a 3.6VDC type AA lithium battery (§ ch. V).
CE LABELING: this device is certified to conform to European regulations for electrical safety, flammability, disruptive
electromagnetic emissions, and immunity to environmental electrical disturbances.
FCC ID : W45 11672
This device complies with part 15 of the FCC rules. Operation is subject to the following two condition:
1. This device may not harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modification not expressly approved by the partyresponsible for compliance. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.

©JRI 4
A solid metal wall will not allow transmission by radio. A perforated metal wall will allow waves
to pass while attenuating them.
b) Positioning
The Nano SPY ALARM must be installed at height near the Nano SPY recorders and the Nano SPY
LINK (<40m, less than 3 m from a power outlet if this option is used (mains / USB transformer)
and at more than 20cm from the passage of a person.
Ethernet Version:
Provide for the presence of an Ethernet socket on an ADSL access point or on a company network
less than 3 meters from the Nano SPY LINK.
Ensure that the port 13251 is open on your internet box (refer to the manual of your ADSL box
for its configuration) or verify this with your IT service provider.
The network must be programmed in DHCP and accept DNS requests.
WiFi Version
Ensure that you are in a zone of WiFi coverage.
To ensure your safety during installation or an intervention on a device placed in a high
position, use proper equipment which is in good condition and provides adequate
stability, wear appropriate, non-slip shoes and install warning signs around the work
area if the intervention takes place in an area of foot traffic.
III. PRESENTATION
a) Control unit
b) Connection
Batterie 3,6VDC
730mAh (3xAAA)
Alarm relay
output
Service connector/
external power
Battery
connection
30VDC / 1A
Status LED
Rear cover /
mounting support
bracket
Ethernet socket
Absent on WiFi version
Bouton sensitif
Mounting holes
(2 on each side)
Reset
Blocking by screw
Light band
Alarm indicator
Identification stamp
on the bottom side

©JRI 5
c) Mounting
/!\ The antenna is not represented on this sequence but be careful when handling
d) Locking
It is possible to lock the Nano SPY LINK onto its cover/support bracket using a screw.
e) Description of the indicator lights
Function
State
Action
Power
On
Mains power present
Flashing
Functioning on battery
Off
Mains power absent
Radio communication
Flashing
Communication with Nano SPY
Network
On
Network presence OK
MySirius
On
MySirius Liaison OK
Open the Nano SPY LINK
Mount
the
cover
Close the Nano SPY LINK







Clic

©JRI 6
IV. CONFIGURATION OF NANO SPY LINK
a) Operating principle
Upon receipt, the Nano SPY LINK Ethernet is configured in DHCP mode. As a result, when connected to the network,
it will automatically connect to the MySyrius server.
In the case of a fixed IP configuration, it is necessary to connect the Nano SPY LINK to a PC via the USB service socket,
and to run the dedicated software in order to enter the Network parameters.
Once the parameters are filled, the Nano SPY LINK is operational
In case of changing the Network settings, it will be necessary to reproduce the action above.
b) Configuration
- Download and install the network configuration software « ConfigLink Network » directly from MySirius. The
download command is available in Administration\Gateways area :
Once the Nano Link is connected to the PC, execute the application « ConfigLink Network.exe » and follow the
indications on the screen.
1. Clic on « Configuration »,
2. Desable « DHCP » mode,
3. Then fill the new IP parameters (IP Address, Netmask, Gateway, DNS),
4. Save the parameters,
5. Reboot the Nano Link.
At this point, the Nano SPY LINK reboots and attempts to connect to the Ethernet network. The “Network”and
“Cloud”lights on indicate that the Nano Link is connected to MySirius.
V. CONFIGURATION OF NANO SPY LINK WIFI
a) Operating principle
As delivered, the le Nano SPY LINK contains no connection information (SSID and password).
It is therefore necessary to connect the Nano SPY LINK to a PC using the maintenance USB socket, and to execute the
dedicated software in order to enter the WiFi parameters.
Once these parameters are entered, the Nano SPY LINK is operational.
In the case of modification of the WiFi router settings, it will be necessary to repeat the above action.
b) Configuration
- Download and install the network configuration software « ConfigLink Network » directly from MySirius. The
download command is available in Administration\Gateways area :
Once the Nano Link is connected to the PC, execute the application « ConfigLink Network.exe » and follow the
indications on the screen.

©JRI 7
1. Enter the SSID
2. Enter the password
3. Save the settings
4. Restart the Nano Link
At this moment, the Nano SPY LINK restarts and tries to connect to the WiFi network.
The indicator lights ‘Network’ and ‘Cloud’ lit indicate that the Nano Link is connected to MySirius.
VI. USE
Le Nano SPY LINK is a gateway allowing transmission of information, sent by the Nano SPY, to the MySirius cloud via
Ethernet or WiFi network. It can be used in two different ways:
As simple gateway
As simple gateway, the Nano SPY LINK provides simply the transmission of information from the Nano SPY to
the MySirius cloud.
As gateway and alert device
Depending on its configuration, the Nano SPY LINK can, in addition to its function as gateway, receive
instructions from MySirius to act as an alert device. In the case of an alert, it can:
Turn on its light band as a function of the event to be signaled
Trigger its buzzer to warn of a problem
Close its dry contact to command an alerting device
a) Taking in charge of alarms
When the Nano SPY LINK triggers an alert, this alert can be stopped in order to take it in charge locally. To do this it
suffices to touch the touch-sensitive button before intervening to correct the problem.
/!\ This action does not correspond to an acknowledgement.
To acknowledge an alarm it is necessary to go on MySirius.
VII. CHARACTERISTICS
RADIO CHARACTERISTICS
Broadcast frequency
2.4GHz
Maximum radiated power
10 dBm (10 mW)
Useful range with SPY RF satellites in buildings
Up to 40 m depending on environment
CARACTERISTIQUES WIFI
Broadcast frequency
Frequency: 2,4 GHz
Modulation: 802.11b and 802.11g
Maximum radiated power
+ 12 dBm
Sensitivity
- 83 dBm
Supported encryption
WEP-128, WPA-PSK (TKIP), WPA2-PSK (AES)
ELECTRICAL CHARACTERISTICS
Mains power
Pluggable power adapter (European model plug) with regulated
voltage output: Input: 230 VAC –Output / 5 VDC - 1A;
3m detachable USB cable
POE
Power over Ethernet available as option for Ethernet models. 3-
meter Ethernet cable supplied
Power consumption
Average consumption: 0.5 W WiFi / 0.85W Ethernet
Peak consumption: 2 W
Backup battery
Type NIMH capacity 730 mAh
Functional autonomy in battery mode
Autonomy for full operation: 6h en WiFi / 4h en Eternet
Recharge time: 125h
MECHANICAL AND ENVIRONMENTAL CHARACTERISTICS
Dimensions
78x78x63 mm
Weight
200g (without mains adapter)
Protection rating
IP20 –functioning inside buildings only
Temperature/Relative operational range
0°C to 40°C –0 to 90% HR

©JRI 8
Pollution / Altitude (IEC 61010-1)
Pollution level: 2
Altitude operational range: 0 à 2000m
SAFETY / COMPLIANCE
CE radio compliance
EN 301 489 / EN 300 220 / EN 61010 / EN 301 511
VIII. MAINTENANCE
Clean the device with a soft cloth, either dry or slightly moistened with water. To remove stubborn dust,
use a cloth soaked in a diluted, non-abrasive de Clean the device with a soft cloth, either dry or slightly
moistened with water. To remove stubborn dust, use a cloth soaked in a diluted, non-abrasive detergent.
Then wipe carefully with a soft dry cloth.
Never use benzene, thinner, alcohol or any type of solvent, which can cause discoloration or deform Clean
the device with a soft cloth, either dry or slightly moistened with water. To remove stubborn dust, use a
cloth soaked in a diluted, non-abrasive de Clean the device with a soft cloth, either dry or slightly
moistened with water. To remove stubborn dust, use a cloth soaked in a diluted, non-abrasive detergent.
Then wipe carefully with a soft dry cloth.
Never use benzene, thinner, alcohol or any type of solvent, which can cause discoloration or deformation
of the surfaces.
IX. GUARANTY
Our material is guaranteed for one year, parts and labor, against any manufacturing defect, functional
failure or abnormal wear. This guarantee covers only the replacement of parts recognized to be defective
as well as the repair of the material in question returned shipping paid to our workshops, and excludes all
damages and interest or incidental expenses.
The starting point of the guarantee is the date of invoice of the concerned product. The invoice must be
provided for any request for application of the guarantee. Repairs under guarantee in no way extend the
guarantee period accorded to the product at the time of sale. Deterioration due to any abnormal usage or
to storage under adverse environmental conditions is excluded from our guarantee.
X. MAINTENANCE CONTRACT
How best to optimize your radiofrequency installation?
Radiofrequency measurement systems communicate through Hertzian waves. Many factors (change in
installation, moving, supplemental wall, interference with another radio system…) can nonetheless modify
the radio pathway previously defined. The use of radiofrequency thus requires periodic monitoring by
recognized specialists.
It is for this reason that JRI has developed for you the maintenance contract. We simplify your procedures
by offering you a fully-integrated solution. This global service offer includes both maintenance and a
metrological service, ensuring the optimum functioning of your devices or of your installation.
You'll no longer have to worry about the maintenance of your devices!
This maintenance contract allows you to benefit, for a minimum period of 2 years, from a variety of
services such as:
- annual or biannual verification of the material
- an extension of the guarantee
- tele maintenance
- telephone assistance [phone] (0,282 € HT/min)
- replacement of the material onsite or by a return to the factory
- verification of measurement accuracy (metrological certificate)
- battery replacement
- access to new software versions

©JRI 9
- intervention within 48 working hours following identification of the fault by our experts
XI. PROTECTION OF THE ENVIRONNEMENT
JRI recommends to its customers the disposal of their unusable and/or irreparable measurement and
recording materials in a manner compatible with the protection of the environment. As the production of
waste materials cannot be avoided, these should be reused through the recycling process best adapted to
the considered materials and to the protection of the environment.
RoHS Directive
The RoHS European directive regulates and limits the presence of dangerous substances in
electronic and electric equipment (EEE).
All new electronic equipment designed, developed and manufactured by JRI are in compliance
with the aforementioned Directive 2002/95/CE.