JSI 4170 User manual

MODEL 4170
4180
4170 4180
CHIMNEY HOOD (ISLAND)
USER MANUAL

2
Resim 1
Photo 1
Figure 1
4170 4180
4170 4180
1
2
3
45
1
2
3
5
5a
min.800/max.1200
Ø400
20
650
100
20
570
400
400
min.800/ max.1200
20
650
27
80
570
15
X
X
X
X
X
X
X
X X
X
Cooker-hood does not work
Illumination Lamp does not work
Cooker-hoods air suction is weak
Cooker-hood does not direct air out
(at places without chimney)
Check electric connection (Voltage of the electric network should be between 220-240V, cooker hood should be connected to grounded plug.)
Check motor switch (Motor switch should be at on position)
Check lamp switch (Lamp switch should be at on position)
Check aluminum filter (Aluminum Cassette Filter should be washed once a month at normal conditions.)
Check lamps (Lamps should be firm.)
Check outlet (Outlet should be open)
Check Carbon Filter (Carbon filter should be replaced with a new one each 2-3 months at the models with Carbon Filter at normal conditions)
If the product does not work:
Before you contact the technical service:
Make sure that the product is plugged in and the electric fuse of the electric wiring
is running. Do not take any action that will damage the product. Before you contact
with technical service, check your cooker hood according to Table 1. If the problem
goes on, contact the seller or the most authorized service.
INTRODUCTION OF THE PRODUCT
1 –Chimney
2 – Body
3 – Control Panel
4 – Aluminum Casette Filter
5 – Illumination
6 – Split Extraction Sheet
Technical Drawing of the Chimney Hood

3
14
4170
220-240 V 50Hz
1
2
3
F
CLASS I
2 x 20 W
210 W
4
5
220
320
420
550
800
2 x 35 W
4180 *This product is designed for usage at
home.
*Your products usage voltage is 220-
240 Volts~50Hz
*Grounded plug is used at your
product's electric network cable. This
cable should definitely be plugged in
a grounded socket.
*All electrical networks should be set
by a qualified electrician.
*Installation applied by unauthorized
people may cause the product to
operate at low performance, damage
of the product and accidents.
*Power supply cable should not be
exposed to press or smash during
montage. Network cordon should not
be placed near the cookers; it may
cause fire if it melts.
*Do not plug into the socket before
installation of the product is
completed.
*Keep the plug at a reachable place
so that you can unplug it in case of
any danger.
*Do not touch the lamps when they
are on for long time. Lamps may hurt
your hand as they will be hot.
*Kitchen cooker hoods are designed
for usage during normal and home-
style cooking. If it is used for other
purposes, failure risk occurs and it will
be out of warranty.
*Follow applicable rules and
directions for passing out outlet air.
(This warning is not valid for usage
without chimney.)
*Flaming foods should not be cooked
under the product.
*Start your product after you put pot,
fry-pan etc. on the hob. Otherwise high
temperature may cause some parts of
your product to get deformed.
*Before you take pot, fry-pan etc. from
the hob, put their lids on.
*Do not leave hot oil on the hob. Pots
that have hot oil in them may cause
self-ignition.
*Pay attention to curtains and covers
during cooking of meals like frying
because oil may flare up.
*Make sure that filters are changed in
convenience. Filters that are not
changed at appropriate time has risk of
causing fire due to oil that will be
gathered on them.
*Do not use filter materials that are not
flame resistant instead of filter.
*Do not operate your product without
aluminum filter; do not remove filters
when the product is on.
*In case of flame, cut power of the
product and the cooking appliances.
(Cut power of the product by plugging it
off the socket).
*Your product may cause fire risk if
cleaning is not applied periodically.
*Cut power of the product before
maintenance process. (Cut power of the
device by unplugging it)
WARNINGS AND SAFETY PRECAUTIONS
In order to use the cooker hood efficiently;
*Use ducts of 150/120mm diameter and as few bends as possible when you make
the chimney connection.
*Pay attention to aluminum filters'cleaning periods and changing periods of carbon
filters.
*Use the product at middle speed if high suction power is not necessary.
* In order to ensure that ventilation occurs correctly, windows of the kitchen should
be kept closed.
TECHNICAL SPECIFICATIONS
Model
Feeding Voltage
Lamp Power (W)
Control Type
Flow Capacity
(m3/h)
Motor Isolation Class
Isolation Class
Speed

413
POWER
(A)
(D)
(B)
(C)
*When chimney hood and the
appliances working with energy other
than electricity are operated at the
same time, negative pressure in the
room should not be more than
4 Pa (4 x 10 bar)
*If there is an appliance working with
fuel or gaseous fuel at the same place
with your hood, this appliance's exhaust
should be isolated from its volume
totally and the appliance should be
hermetic type.
*When chimney connection is applied to
your product, use ducts of 150mm or
120mm diameter. Duct connection
should be as short as possible and
should include few bends.
*Keep package materials away from
children as they may be dangerous for
them.
*Be sure that your child does not play
with the product. Do not allow kids to
use your product.
*If power supply cable is damaged, this
cable should be changed by its
producer or its service agency or a
personnel who is a specialist at the
same level in order to prevent a
dangerous situation.
*In case of flame, cut power of the
cooker hood and the cooking
appliances, cover the flame. Never use
water in order to extinguish it.
Use “MAX 6 A” fuse at cooker hood
installment for your security.
Warning about Transportation and Carriage
*All the materials used at package of your product are suitable for recycling.
*Please comply with the signs on the product's box during transportation.
*Hold the holders placed at sides of the box in order to carry your product.
If you need transportation;
*Keep the original box.
*Carry your product in its original box; comply with the carrying signs on the
product's box.
If there is no original package;
*Do not put heavy material on the chimney hood.
*Keep the external surface from bash.
*Pack your product to avoid damages.
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the
transportation responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
-5
Usage of remote control
You can use your chimney hood with remote control. Please follow below
directions in order to use your product with remote control;
A)Motor on/off
B)Speed up
C)Speed down
D)Lamps on/off

5
Standard Accessories
Plastic chimney
Plastic chimney is applied to chimney hood
air outlet (Photo 2)
Installation, taking off your product from its package:
*Check if there is any deformation on your product.
*Transportation damages and failures should immediately be reported to the
transportation responsible.
*If you notice any damage please report to the seller.
*Do not allow children to play with packing material!!!
Rhoto 2
Figure 2
Min.65 cm
Min.75 cm
Taking off the split extraction plate
In order to take off the split extraction plate, pull
it downwards holding upper right and upper left
points. Figure 3
Figure 3
12
Place of the Product:
After installation of your product, distance
between range hood and electrical hob should
be at least 65 cm and gas hobs at least
75cm.(Figure 2)
TOUCH BUTTON LOCATION
Remote control
receiver
Usage of 5 Speed Digital Control
Usage
Remove protective folio on the inox product after installation.
Speed Selection The product has 5 speeds of ventilation level. One of 1,2,3,4,5
speeds is selected in accordance with steam of cooking or fry. Motor is started
pressing control button on the front panel. Speed is increased pressing
button, and decreased by pressing button. Automatic timer (TIMER) is available
at the models with electronic remote control.
Illumination
The product has 2 lamps and one lamp button to operate illumination. Press lamp
button in order to start illumination.
Cleaning Periods of the Aluminum Filters:
Filters should be cleaned when “C” signal appears on Display or (according to
usage) each 2-3 weeks. In order to remove “C” signal, after the filters are cleaned
and replaced to their place, press button more than 3 seconds (when the
product is at off position). Letter “E” will appear on Display and the product will
operate as normal. If you would like to continue using the product without deleting
“C” signal, when you press the button active speed will appear for 1 second,
then “C” signal will appear once more and the motor will continue operating.
NOTE: “C” signal will appear after usage of the product for 60 hours.
NOTE: If your product has dimmer function please pay attention to the
explanation stated below.
Changing Brightness of the Lamp (Dimmer):
When the lamp is on, lamp's brightness starts to change continuously if you keep
lamp button pressed. When you get the brightness level that you wish and stop
pressing the button, brightness that is set will be recorded, and the product will
start with the same brightness during next usage. When you press the lamp button
2 times consecutively, the lamp will be on at the highest brightness level.
The lamp will always start at the brightness level that is set during last usage.
When button is pressed more that 2 seconds, timer function for 15 minutes will be on
and display will signal. Motor will stop 15 minutes later.

6
Min.84 cm
Min.94 cm
MONTAGE OF ISLAND CHIMNEY HOOD
1)Distance between motor block and gas hob
should be 84cm, distance between motor block
and electrocal hob should be 94cm. Figure 4
2) Take off motor block from its package.
3)In order to set distance mentioned at item 1;
take off the screws shown at Figure 5 and
arrange place of the motor block that is composed
of 2 blocks pushing it inwards or pulling outwards.
4)Nail the screws again to appropriate places.
NOTE: Part shown as front on the product shows the position that control
button will be placed.
A
B
C
D
5)Stick the montaje template provided with your
product to the place that your product will be
hung. Drill ø 10mm holes on A,B,C,D points.
6) Drive ø10mm wall plugs in to A,B,C,D holes.
7)Nail 5,5x45ysb screws to the wall plugs so that
there will be 5mm distance between the wall and
screw head.
8)Pass the holes similar to key hole that are on
the motor block through 5,5x45ysb screws that
you nailed on the wall. Then turn the motor block
clockwise.
9)After you pass the screw canals that are on the
motor block to montage screws thightly , fix the
motor block screwing tightly. Figure 6
Figure 4
Figure 5
Figure 6 11
Yýkanabilir Alüminyum
kaset filtre
Figure 14
Photo 5
MAINTENANCE
*Disconnect electricity connection before
maintenance and cleaning process.
*Aluminum cassette filter holds the dust and the
oil in the air.
*Metal filter should be washed once in a month
with hot and soaped water or, if possible, at
dishwasher (60C).
*Take off aluminum cassette filter pressing on
springy latches on end point. After cleaning, do
not replace before it dries.
*Outer surface of the cooker hood should be
wiped with a wet cloth that is wetted with water or
alcohol.
*Please avoid contact of electronic parts with
water or similar materials.
*Using Inox cleaning and maintenance products
available in the market will help your product to
perform longer.
Warning: Aluminum filters may be washed in the
dishwasher. Color of aluminum filters may change
after several washings. This is normal and it is not
necessary to change the filters.
Efficient Ventilation
In order to ensure correct ventilation, keep your kitchen windows closed.
IMPORTANT NOTE
Please pay attention when the product is operated at the same time with a product
which operates using air and fuel (for instance; heater, water heater etc. which
operates using gas, diesel fuel, coal or wood), since cooker hood may affect
burning negatively as it directs the air out.
This warning is not valid for usage without chimney.

7
As bends and ells will result in decrease in suction power, avoid using them as
much as possible. Photo 3
Photo 3
Aluminum
flue outlet
10)Fix one side of the aluminum flexible duct to
product's plastic chimney and the other end to
kitchen chimney. (Make sure that this
connection is so tight that it will not be
disconnected even when the product is
operating at high speeds.)Figure 7
11)Passing the chimney over the motor block,
fix it using screws provided with your product.
Figure 8
Figure 7
Figure 8
10
Figure 13
Replacing Carbon Filter
It is necessary to install 2 carbon filters to your
product.
To place the carbon filter, place your filter on
connection channels on motor and turn it
clockwise.
In order to remove filter, turn it anti-clockwise.
Figure 13
Active Carbon Filter
To provide air recirculation where product's
chimney air outlet cannot be connected to
exterior, it is necessary to use active carbon
filter with your product. You may purchase this
accessory from authorized sellers and after
sales services. (Photo 4)
Carbon Filter Usage
Your product is compatible with two types of carbon filters.
You may see following information on how to use carbon filters.
Before installing or replacing carbon filter, first you should cut your product's power
off.
Carbon filters should be replaced with a new one each 3-5 months because it is
used at kitchens that does not have chimney outlet.
Carbon filter should never be washed.
Grease filters should be installed on the product even when carbon filter is not in
use. Do not use your product without grease filter.
Photo 4
Round Carbon
Filter
Correct Incorrect

8
12)Place body of the poduct on motor block.
Figure 9
13)Pass hanging holes to the plastic headed
screws, turn the body clockwise and tighten the
screws. Figure 9a
Lamp hear
connection
Key
connection
14)Connect lamp holder and switch. Figure 10
15)Place aluminum casette filter.
Figure 9
Figure 9a
Figure 10
9
Figure 12
Figure 11
Replacing the Lamps
Cut off the connection of the cooker hood with
electricity. Take off the aluminum cassette
filter. Take off the failed lamp and replace it
with a new one that is of the same rating.
(Please wait for the lamps to cool as they
might hurt your hand.)
Replacing 50W Halogen Lamp
In order to change halogen lamps, take the
lamp downwards pushing back of lamp holder
downwards and then turning it a little bit anti-
clockwise take it off downwards. Figure 11
Replacing 20W Halogen Lamps
Take off the glass cover on the lamp with a
substance that will not scratch surface of the
product as shown on the figure. Take off the
faulty lamp pulling it downwards and replace
it with a new one. Figure 12
Note: Do not hold the new lamp with
naked hand, sweat or wetness of your
hand will cause the lamp to fail because of
the heat that will occur when the lamp is
on.
Functions of the Product
Your hood is compatible for use with our without chimney.
Usage with chimney
The product should be connected to a chimney that will direct the air out during
usage with chimney. In order to achieve best performance, pay attention that the
duct system follows the shortest way for connection to the chimney. Your product is
produced as it will be appropriate for usage with chimney.
Attention!!!
Outlet of the product should not be connected to air canals that have other
smoke as well.