JSPORTS JB101 User manual

JB101 User Manual
Accessories included with your product
Rubber stand Cable Tie
2. Magnet alignment mark2. Magnet alignment mark
1. LED indicator1. LED indicator
3. Cable tie through hole 3. Cable tie through hole 5. Rubber stand5. Rubber stand
4. Battery ribbon4. Battery ribbon
Install JB101 on your Bike
Step1: Place sensor on left chainstay with 2 cable tie
Let Logo side outwards
Step2: Insert the pointed end of the cable into the
locking piece, Keep cable loose to allow some
adjustment of position and tilt angle.
Step5:Tilt the JB101 sensor top side closer to magnet within 5mm for
better sensing performance
Step6: Swing rear wheel ,let the magnet pass through JB101 if LED turn
on sequentially. Then tighten 2 cable tie and cut off redundant
cable to finish hardware installation
5mm5mm
Speed Meter
Install Battery
Step 1: Remove JB101 rubber stand
Step 2: pull out battery Ribbon
Step 3: battery push into battery
holder
Step 4: LED will flashing , if battery is install
correct
Step 6: Push back the battery ribbon
and covered with Rubber stand
Note: The battery Anode mark should
face to Logo, same direction
as icon on bottom side of JB101
Step3: Mount the Magnet on the spoke, place the
spoke in the groove of the plastic piece
Step4: Move magnet to align triangle mark on JB101 ,
tight the screw to fix magnet position.
Note: place JB101 on chainstay close to the Rim

App
Device Requirement
This product supports mobile phone via Bluetooth wireless technology.
Please pair it with your cellular phone when using this product for the
first time, system requirements as bellow:
‧iOS 5.0 or later.
‧Android 6.0 or later.
‧Built-in Bluetooth low power wireless connectivity.
Pair with Cellular Phone App
Step1: Enable the Cellular Phone GPS & Bluetooth Device
Step2: Enable JSports App
Setup
Track Log About
Recording
Paring Device
Step 1: turn to the setup page and click “select JSports Device”
Step 2: Turn the bike wheel
Step 3: Device Paired
Turn the crank
counter-
clockwise.
Setup items
Back to main page
Pairing Bike
Bike Wheel Size
Display Unit
Gender option
Owner Age
Driver Height
User Manual
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.，Increase the separation between the
equipment and receiver，Connect the equipment into an outlet on a circuit different from that to which the receiver is connected，Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device and its antenna(s) must not be co-located
or operating in conjunction with any other antenna or transmitter.
NCC 警語:
•「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能」。
•「經「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機
須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」。
FCC警語:IMPORTANT NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Track Log About Step 3: Device Paired
Device had Pairing with JSports
App when Device name appeared
Bike Far Away
Alarm
Display Language
Set to Default