Julian Bowen Limited Rialto RIA302 User manual

FABRIC STORAGE BED 150CM
RIA302
VERSION: 210518
Assembly Instructions

02
Customer Services
No Extra
Tools Required

FLAT WASHER (12 PCS)
HARDWARE
PARTS
A
M8 x 25mm (12 PCS)
C
M6 x 30mm (6 PCS)
D
M6 x 15mm (12 PCS)
B
NUT (2 PCS)
E
M6 x 68mm (2 PCS)
FG
SPRING WASHER (12 PCS)
H
5mm ALLEN KEY (1 PC)
IJ
4mm ALLEN KEY (1 PC) SPANNER (1 PC)
03
2
3
4
1
6
5
7
11
10
8
9
12
13
14
15

Safety Advise
04
Please take the time to carefully read through the whole of
these instructions before you commence.
Keep these instructions for future reference.
Unpack, inspect and check off all of the contents.
Please dispose of all packaging safety.
Small component part could choke a child if swallowed.
We strongly recommend that you keep children well away
from the work area.
It would be sensible to lay a sheet or blanket on the oor
where you intend to work to avoid scratching this product
and to protect your oor.
This product is heavy. Take extreme care when lifting to
avoid personal injury or damage to the product.
Assemble the product as close to its intended nal position
in the room as possible.
We strongly urge that you do not use Power Tools, Such as
drills or electric screwdrivers during this assembly as this
could cause irreparable damage to your product and will
invalidate the warranty.
HANDY HINT: If you keep the hardware in a bowl during
assembly you will be less likely to lose them.

2
1
2
A
11
3
H
F
&
G
23
Attaching side rails to headboard.
Repeat step 1 for footboard.
Before tightening the bolts, please
ensure the bed frame is square.
05

06
3
4
1
2
Fix corner brackets, then repeat for other 3 corner
brackets in each corner of the bed frame.
D
I
13
&
Fix holding block on back of footboard
I
E
2
9
10

Before connecting the hydraulic arm, ensure the
07
5Secure hydraulic arms
DO NOT OVERTIGHTEN THE NUTS !
lifting mechanism is functioning correctly - it should lift
up and down freely with adequate clearance on all sides.
J
B
6Assemble the base
3
4
2
666
7
5
5
D
I
5
7
5
3&4
8
I
6
C

08
7Attach non-woven fabric dust cover rst, then adjustable legs.
11
14
13
13
13
15
8Assemble slats
14
15
13
16

Please use extra caution when opening and closing the bed, ensure
It is imperative that the bed is aligned squarely to prevent the
09
9
Attach belt to the metal frame by loop-on method as shown, pull
tight after loop-on.
12
10 Place the mattress onto the frame. (MATTRESS NOT INCLUDED)
Notes:
frame from catching on and damaging the upholstered side rails.
a similar spacing on each side of the frame.

10
General Care
Wipe clean with a slightly damp soft cloth.
Avoid the use of all household cleaners and abrasives.
When moving your furniture, carefully lift into place.
Never drag or push the pieces across the oor as this
will cause damage to the joints and could result in failure
to the product that will invalidate the warranty.
Recommendations
Periodical re-tightening of xings.
Warning
This unit is heavy. Please use an assistant when lifting.
Notes
We've tried to make this piece of furniture as easy to
assemble as possible.
In the unlikely event that you have problems putting
it together or have damaged or missing pieces,
please contact our customer services on 01623 727374.