Julian Bowen SAN103 User manual

Approximate Assembly Time
Before you start....
Please carefully unpack and lay out all of the component parts to ensure nothing
is missing and to check each component for any obvious damage.
Should you identify any concerns at this stage please contact the retailer from
whom this product was purchased. Please quote your order number, details of
your issue, the product code, and the batch number from the cartons which will
help to resolve your issue as quickly as possible.
Version Number - 1.0 Product Code - SAN103
Tools RequiredPeople Required to Assemble
FABRIC STORAGE BED 180CM
ASSEMBLY
INSTRUCTIONS
1hr
1900
1145
2210

No Extra
Tools Required
No Extra
Tools Required
No Extra
Tools Required
2
8

M8x20mm
8x M8x30mm
14x
M8x65mm
8x
M5x50mm
4x
M8
8x
Please check all hardware matches the list below. Should
you notice any are missing please contact your retailer.
We strongly advise that you do not use Power Tools, such as
drills or electric screwdrivers during the assembly as this
may cause irreparable damage and will invalidate your
warranty.
3
A
M
C
E F G
Already inserted into
Head & Foot Ends
I
A
M8x40mm
4x
1x
D
H
43x 6x 2x
I J K M5
1x
L
16x
M8x30mm
+Spring Washer B
1x

PARTS
4
Please ensure you carefully check all the pieces, should you have any
concerns please contact the retailer before assembly commences.
Please have your order number, details of the issue, the product code,
and the batch number from the cartons as this will help us to resolve
your issue much faster.
02
03
08
13
04
03
06
04
01
15
04
04
09 09
14
12
05
11
07
10

ASSEMBLY ADVICE
Please take the time to carefully read through these instructions
before you commence.
Keep these instructions for future reference.
We advise that the product is assembled in the room it is intended for.
We advise that you keep the hardware in a bowl during assembly to
avoid losing anything.
We strongly recommend that you keep children away from the work
area.
Small component parts could choke a child if swallowed.
We recommend you use a sheet or blanket to protect both floor and
product through the assembly stages.
Never push or pull the product as this could cause both personal injury
or irreparable damage to product or floor.
We have tried to make this piece of furniture easy to assemble if the
instructions are followed carefully.
In the unlikely event that you have problems with assembling the
product or have missing or damaged parts, please contact your
retailer and we will assist them in rectifying the problem as quickly as
possible.
Remember we strongly urge you DO NOT use power tools such as drill
or electric screwdrivers as this could cause irreparable damage to
your product and will invalidate your warranty.
5

03
15
15
02
L
DI
L
13
I
C
Do not fully tighten the bolts as the
brackets may need to be adjusted
once the mattress frame is attached.
1
2
6

02
04
04
A
L
01 & 02
01
H
K
K
I
please note that Bolt (A) x 16
+ Flat washer (I) x 16 are
prefixed into parts 1 & 2
I
03
03
03
06
F
3
4
7

11
07
07
07
07
12
05
09
LBI
10
LE
I
M
G
14
5
6
8
09
11
11

I
J
C
L
08
13
G
M
M
Check that the frame is central by adjusting
the alignment of the frame and brackets
before fully tightening all bolts. The metal
frame should not contact the faux leather
at any point.
7
8
9

Attention :
Place the mattress onto the frame BEFORE closing or this could result in damage to the bed.
(MATTRESS NOT INCLUDED)
9
10
10
Note:
It is imperative that the bed is aligned squarely to prevent the frame
from catching on and damaging the upholstered side rails.
Please use extra caution when opening and closing the bed for the
first few times.
Ensure a similar spacing on each side of the frame.