Julian Bowen WIL001 User manual

Before you start....
Please carefully unpack and lay out all of the component parts to ensure nothing
is missing and to check each component for any obvious damage.
Should you identify any concerns at this stage please contact the retailer from
whom this product was purchased. Please quote your order number, details of
your issue, the product code, and the batch number from the cartons which will
help to resolve your issue as quickly as possible.
Version Number - 1.0 Product Code - WIL001
Tools RequiredPeople Required to Assemble
FABRIC 135CM 4 DRAWER BED
1hr
Approximate Assembly Time
ASSEMBLY
INSTRUCTIONS
1500
1300
2070

No Extra
Tools Required
No Extra
Tools Required
No Extra
Tools Required
2
8

M8x30mm
+Spring Washer
+Flat Washer
12x 16x
Already inserted into
Head & Foot Ends
M5x70mm
3x
30x60
4x
M4x20mm
1x
Please check all hardware matches the list below. Should
you notice any are missing please contact your retailer.
We strongly advise that you do not use Power Tools, such as
drills or electric screwdrivers during the assembly as this
may cause irreparable damage and will invalidate your
warranty.
3
A B C
E F G
I 4x J
M4x20mm
64x MN
32x
M5x50mm
8x
D
H
O
48x L
M5
1x
M8x45mm
+Flat Washer
8x
M4x30mm
20x
M5x50mm
48x
M8x30mm
+Spring Washer
+Flat Washer
2x K

PARTS
4
Please ensure you carefully check all the pieces, should you have any
concerns please contact the retailer before assembly commences.
Please have your order number, details of the issue, the product code,
and the batch number from the cartons as this will help us to resolve
your issue much faster.
face out
face out
(2x)
01
02
03
03
04
05
05
05
06
06
06
06
07 (32x)
08
08
08
08
10
12
11
11 13
13
14
15
09
16
(2x)
18
19
11
11 13
13
20
17
16

ASSEMBLY ADVICE
Please take the time to carefully read through these instructions
before you commence.
Keep these instructions for future reference.
We advise that the product is assembled in the room it is intended for.
We advise that you keep the hardware in a bowl during assembly to
avoid losing anything.
We strongly recommend that you keep children away from the work
area.
Small component parts could choke a child if swallowed.
We recommend you use a sheet or blanket to protect both floor and
product through the assembly stages.
Never push or pull the product as this could cause both personal injury
or irreparable damage to product or floor.
We have tried to make this piece of furniture easy to assemble if the
instructions are followed carefully.
In the unlikely event that you have problems with assembling the
product or have missing or damaged parts, please contact your
retailer and we will assist them in rectifying the problem as quickly as
possible.
Remember we strongly urge you DO NOT use power tools such as drill
or electric screwdrivers as this could cause irreparable damage to
your product and will invalidate your warranty.
5

Please note that
the Bolt (A) x 12
are prefixed into
parts 1 & 2
1
2
3
E
6
01
03
03
02
03
04 04
05
05
05
05
B
A
01
02 06
06
01
02
H
06
06
I
I
I
H
06
06
I

face out
face out
face out
face out
face out
4
6
7
02
5
03
03
02
09
03
E
F
08
ARROWS ON LABELS
POINT TO EACH OTHER
J
J
08
09
02
02
01
01
04
04
G
E
face out
K

face out
D
D
D
PUSH
PUSH
PUSH
C
07
07
C
07
07
7
8
C
DD
07 07
8

FOLLOW LINE ON BACK OF
DRAWER FACE PANEL
III III
Positions For Castors
(Large) x2
Part 13 x 2
9
9
Important:
Make sure when you fit the nuts
that the hole is in the correct
alignment.
Drawer Assembly
L
10
IV V
15
15
10
11
14
11
12
13
13
13
16
10
L
L
L
O
O
O
MN

(Small) x2
face out
FOLLOW LINE ON BACK OF
DRAWER FACE PANEL
11
13
10
Important:
Make sure when you fit the nuts
that the hole is in the correct
alignment.
Drawer Assembly L
12 Positions For Castors
III III
IV V
13
13
13
16 17
17
18
18
11
20
11
19
L
L
L
Part 13 x 2
O
O
O
MN