Juna JMC-03 User manual

TV DVB-T for CAR
JMC-03 Model:
JMC-03_V2.2_RNS 510
INSTALLATION INSTRUCTIONS
1. INSTRODUCTION ..................................................................
2. RECOMMENDATIONS ...........................................................
3. CONNECTION SCHEDULE OF SET COMPONENTS.........
4. BASIC TECHNICAL PARAMETERS .....................................
5. ELEMENTS OF THE SET ......................................................
Table of Contents
ul. Zgorzelicka 34 , 97-200 Tomaszow Mazowiecki POLAND
JuNa PPHU Manufacturer
2
2
4
5
5

1. Introduction
2. Recommendations
ul. Zgorzelicka 34 , 97-200 Tomaszow Mazowiecki POLAND
JuNa PPHU Manufacturer
JMC-03 module is modern device designed to receive Digital terrestrial television
Signal DVB-T. This unit is dedicated to install in cars of VW/Skoda/Seat brand
equipped with multimedia system RNS510. After installation JMC – 03 is recognized
by RNS510 unit and added to list of supported devices in car. This allow to control it
over existing in car RNS510 system. Dual TV receiver with two antennas installed in
different places in car makes that device is less sensitive for poor quality signal while
car is during ride. The JMC-03 set includes all necessary components for fast
Plug & Play assembly of the device in the car. JMC-03 module is modern device
designed to receive Digital terrestrial television Signal DVB-T. This unit is dedicated
to install in cars of VW/Skoda/Seat brand equipped with multimedia system RNS510.
After installation JMC-03 is recognized by RNS510 unit and added to list of
supported devices in car. This allow to control it over existing in car RNS510 system.
Dual TV receiver with two antennas installed in different places in car makes that
device is less sensitive for poor quality signal while car is during ride. The JMC-03
set includes all necessary components for fast Plug&Play assembly of the device in
the car.
Copyright
All assembly and operating instructions are protected by copyright. Distributing
documentation via print or online media is only allowed with the prior consent of
JUNA electronics.
Important
Please read installation manual very careful and keep it in right way. During
installation, pay attention to all relevant aspects related to safety of installation and
use of the device.
The priority during the design and production of all devices by JUNA electronics
company is security and service comfort. It has been achieved by
applying the modern techniques of design and production processes of electronic
devices.
Module should be installed in technical workshops by qualified personnel or
by people who have experience in this type of installations. Installation of devices by
not qualification people can cause injury to persons or damage to property.
2

2.2 Recommendations
ul. Zgorzelicka 34 , 97-200 Tomaszow Mazowiecki POLAND
JuNa PPHU Manufacturer
It is recommended keep to the general safety rules and pay attention for any
threat that can cause of damage to the vehicle.
We advice to mount device in safety place, where it is not exposed for moisture,
water or too high temperatures.
Device should not be installed in places where it could difficult safe driving or
operating efficiency of other units installed in vehicle.
The devices can be connected only to 12V. Modules can't be used in vehicles with
24V and higher voltage.
Please note that most of our devices are based on software that may require an
update. That's why you should always mount the device in easily available place in
the vehicle.
In some countries it may be necessary to check the legal provisions before
installation and startup of the device. In the interest of high quality and development
of our products, JUNA Electronics reserves the right to make technical changes.
In the case of a warranty claim, the device should be sent back to the seller in
original packaging with a detailed description of the problem with attached
purchase invoice.
Warranty claims as well as exploitation rights expire due:
A) Not authorized changes in devices or accessories, which have not been approved
or have not been provided by the manufacturer or his partners.
B) Opening the device's box.
C) Yourself repair the device.
D) Improper use / improper operation of the device
E) Mechanical damage (drop, intentional damage, accident etc.)
F) Flooding with water or other liquids
3

1. Switch off the radio unit and the car's ignition switch.
2. Remove the radio unit from the car dashboard.
3. Unplug the ISO plug from the radio unit and connect it to the cable socket in
intermediary W-TV102b, which is added to the JMC-03 set.
4. Connect the ISO connector and video cable connector to the sockets of
the radio unit.
5. Connect the connectors and to the DVB-T JMC-03 module.
6. Connect antennas ANT.1, ANT.2 to antenna sockets in JMC-03 module.
7. Turn on the ignition switch and start the radio unit.
8. On the radio control panel, press the MEDIA button, then on the touch panel
press VIDEO label.
4
1
23
ul. Zgorzelicka 34 , 97-200 Tomaszow Mazowiecki POLAND
JuNa PPHU Manufacturer
3. Connection schedule of set components
DVB-T JMC-03 connection to the RNS 510 unit
ANT. 1
ANT. 2
3
2
1
45
6
W-TV102b
56
4

4. Basic technical parameters
ul. Zgorzelicka 34 , 97-200 Tomaszow Mazowiecki POLAND
JuNa PPHU Manufacturer
1. Supply voltage
2. Power consumption in the active state max.
3. Power consumption in standby mode
4. Maximum power consumption from the USB socket
5. Communication and control
6. Housing
7. Dimensions
8. Weight
5. Elements of the set
1. DVB-T module
2. Connecting cable
3. DVB-T antenna 2 pcs.
W-TV102b
ANT09
JMC-03
for RNS 510
ANT09
- 12V
- 410mA
- 13mA
- 500mA
- CAN bus
- Metal
-144mm x 94mm x 28mm
- 368g
- JMC - 03
- W-TV102b
- ANT09
5