Jung eNet FM HS 1 T User manual

Remote control, 1-channel Toggle
eNet
Remote control, 1-channel Toggle
Art. No. : FM HS 1 T
Operating instructions
1 Safety instructions
Keep button cells out of reach of children! If button cells are swallowed, get medical help
immediately.
Risk of explosion! Do not throw batteries into fire.
Risk of explosion! Do not recharge batteries.
The radio communication takes place via a non-exclusively available transmission path,
and is therefore not suitable for safety-related applications, such as emergency stop and
emergency call.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: Radio hand transmitter 1-gang
(1) Status LED
(2) Button
3 Function
System information
This device is a part of the eNet system.
High transmission reliability at a radio frequency of 868 MHz is achieved by the transmission
behaviour and bidirectional data transfer.
The range of a radio system depends on various external circumstances. The range can be
optimised by the choice of installation location.
This device complies with the requirements of the R&TTE Directive 1999/5/EC. Declaration of
Conformity and further information on the eNet system can be found on our website.
The device may be operated in all EU and EFTA countries.
1/6
82582503
J:0082582503 13.03.2014

Intended use
- Radio hand transmitter for radio transmission of switching, dimming, and blind movement
commands
- Operation with radio actuators from the eNet system
Product characteristics
- A button for switching and dimming a channel
- Status indication with LED
- Battery-powered device
- Signalling of transmission errors can be switched off
Can be set with eNet server:
- Scenes: All On, All Off, individual scenes
- Operation locks
iIf settings are changed with the eNet server, operation and signalling could vary from what
is described here.
iThe parameter list is in the Internet in the documentation for this device.
Supplementary functions with eNet server
- Update of the device software
- Reading of error memory
4 Operation
The radio hand-held transmitter is optimised for switch actuators in push-button operation.
Button pressed, push-button actuator switches on, Button released, push-button actuator
switches off.
In addition, the hand-held transmitter can be used in various ways:
- Single-surface operation, lighting: Switching lighting on or off or dimming brighter/darker
takes place alternately when the button is pressed repeatedly.
- Single-surface operation, Venetian blind: Upward or downward movement takes place
alternately when the button is pressed repeatedly.
iIt may be the case that the button has to be pressed twice, in order to obtain the desired
result.
Function of status LED in operation
As soon as the button is pressed or released, the status LED (1) first signals radio transmission
- LED turns red for 3 seconds
and then the actuator status
- LED turns green for 3 seconds:
At least one actuator is switched on, or one Venetian blind is not in the top end position
- LED remains off:
All the actuators are switched off or the blinds are all in the upper end position
or - if there is no status message from an actuator - a transmission error.
- The LED rapidly flashes red for 5 seconds:
The status message of at least one actuator is missing
Operating light
oSwitching: Press button for less than 0.4 seconds.
oDimming: Press the button for longer than 0.4 seconds. The dimming process ends when
the button is released.
oSwitching on at minimum brightness: Press the button for longer than 0.4 seconds.
Operating blind
oMoving the Venetian blind: Press the button for longer than 1 second.
iChange of direction for moving Venetian blind: Press the button for longer than 1 second.
Change of direction for stationary Venetian blind: First, press the button for less than
1 second, then press the button for longer than 1 second.
2/6
82582503
J:0082582503 13.03.2014
eNet
Remote control, 1-channel Toggle

oStopping the Venetian blind: Press the button for less than 1 second.
oAdjusting the Venetian blind: Press the button for less than 1 second.
iIf the break between the two button actuations is longer than approx. 1 second, the
direction will change.
Operating push-button actuator
oButtons: The load is switched on for the duration of the button-press.
iThe maximum actuation length is 60 seconds.
5 Information for electrically skilled persons
5.1 Commissioning
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
During commissioning, cover the parts carrying voltage on radio transmitters
and actuators and in their surrounding area.
Insert battery
WARNING!
Risk of chemical burns.
Batteries can burst and leak.
Replace batteries only with an identical or equivalent type.
oOpen battery compartment on the rear side of the hand-held transmitter.
iKeep contacts of batteries and device free of grease.
oApply battery to the positive contact of the battery holder. Observe polarity: the positive
pole of the battery must be at the top.
oPress gently on battery to snap it in.
oClose battery compartment.
Hand-held transmitter is ready for operation.
Connecting to radio actuator
Figure 2: Prog Button in the battery compartment
iUp to 10 radio actuators can be connected to a transmitter in a single step.
3/6
82582503
J:0082582503 13.03.2014
eNet
Remote control, 1-channel Toggle

oSwitch the actuator to programming mode (see actuator instructions).
oPress the Prog (figure 2) button for longer than 4 seconds.
Status LED (1) flashes red. The hand-held transmitter is in programming mode for approx.
1 minute.
oPress button briefly
The status LED lights up for approx. 5 seconds, and the hand-held transmitter is connected
to the actuator. The hand-held transmitter and actuator exit the programming mode
automatically.
iIf the status LED of the radio transmitter flashes 3 times at 1-second intervals for approx.
5 seconds, then the programming operation was not successful. The actuator is outside
radio range, not in programming mode or there are radio faults.
iIf the status LED of the actuator flashes 3 times at 1-second intervals for approx. 5
seconds, then the programming operation was not successful. All the memory locations in
the actuator or radio transmitter are occupied.
iPress the PROG button once again for longer than 4 seconds to terminate the
programming mode earlier.
Disconnecting connection to an actuator
oCarry out the same steps as when connecting (see the chapter Connecting to radio
actuator).
The status LED of the actuator flashes quickly for 5 seconds. The actuator is disconnected
from the radio transmitter. The actuator and radio transmitter exit the programming mode
automatically.
Reset button
All connections of the button (2) to the actuators are disconnected and parameters are reset to
default setting.
iThe connections in the actuators are preserved and must be deleted separately.
oPress the Prog button for longer than 20 seconds.
The status LED (1) flashes red after 4 seconds. The status LED flashes faster after
20 seconds.
oRelease Prog button and press button (2) briefly once again within 10 seconds.
The status LED flashes more slowly for approx. 5 seconds.
The button (2) is reset. The setting as channel button or scene button is retained.
Resetting the hand-held transmitter to the default setting
All connections to actuators are disconnected and parameters are reset to default setting.
iThe connections in the actuators are preserved and must be deleted separately.
oPress the Prog button for longer than 20 seconds.
The status LED (1) flashes red after 4 seconds. The status LED flashes faster after
20 seconds.
oRelease Prog button and press the Prog button briefly once again within 10 seconds.
The status LED flashes more slowly for approx. 5 seconds.
The hand-held transmitter is reset to default setting. Button (2) is set as channel button.
6 Appendix
Remove empty batteries immediately and dispose of in an environmentally friendly
manner. Do not throw batteries into household waste. Consult your local authorities
about environmentally friendly disposal. According to statutory provisions, the end
consumer is obligated to return used batteries.
The icon confirms the conformity of the product to the relevant guidelines.
4/6
82582503
J:0082582503 13.03.2014
eNet
Remote control, 1-channel Toggle

6.1 Technical data
Rated voltage DC 3 V
Battery type 1×Lithium CR 2450N
Ambient temperature -5 ... +45 °C
Degree of protection IP 20
Dimensions L×W×H 55×40.5×15 mm
Radio frequency 868.3 MHz
Transmitting power max. 20 mW
Transmitting range in free field typical 100 m
6.2 Parameter list
Settings window
Device settings
Parameter name Setting options, Basic
setting
Explanations
Manual commissioning On, Off
Basic setting: On
Blocks manual commissioning
for the device channel. In the
"Off" setting, the device
cannot be reset to the factory
setting.
Channel 1 Rocker switch, scene
Basic setting: Rocker switch
Setting the buttons of the
channel as channel buttons
(rocker switch) or scene
buttons (scene).
Settings, channel/scene
Parameter name Setting options, Basic
setting
Explanations
Local Operation On, Off
Basic setting: On
Blocks the device channel for
local operation.
Manual commissioning On, Off
Basic setting: On
Blocks manual commissioning
for the device channel. In the
"Off" setting, the device
cannot be reset to the factory
setting.
Sum status / transmission
repetitions
On, Off/Transmit 2x…11x,
Off/Transmit 4x (without
connection)
Basic setting: On
On: The transmitter evaluates
the received status messages
and displays them as an
overall status. If individual
status messages fail, then the
transmitter will repeat its
telegram up to three times.
Off/Transmit x times: The
evaluation and display of the
overall status is deactivated.
The number of telegram
repetitions is prescribed. In
this setting, no transmission
errors are displayed.
Off/Transmit 4x (without
connection): Reserved for
sensors which transmit without
a connection.
5/6
82582503
J:0082582503 13.03.2014
eNet
Remote control, 1-channel Toggle

6.3 Troubleshooting
After a button has been pressed, the status LED flashes red slowly for 3 seconds.
Cause: Battery in the hand-held transmitter is almost empty.
Changing the battery (see chapter Commissioning - Inserting the battery).
Receiver does not react, status LED displays a transmission error. Status LED flashes
red quickly for 3 seconds.
Cause 1: Radio range exceeded. Structural obstacles reduce the range.
Using a radio repeater.
Cause 2: Actuator is not ready for operation.
Check the actuator and mains voltage.
Cause 3: There are radio faults, e.g. through outside radio.
Eliminate radio interference.
iThe actuator causing the transmission error can be removed from the display of
transmission errors. To do this, briefly press the Prog button of the hand-held transmitter
during signalling. The actuator is automatically taken into account again when it transmits a
status message after radio transmission.
6.4 Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
We provide a warranty as provided for by law.
Please send the device with a description of the defect to our central customer service office.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-2 04
[email protected]
www.jung.de
Service Center
Kupferstr. 17-19
44532 Lünen
Germany
6/6
82582503
J:0082582503 13.03.2014
eNet
Remote control, 1-channel Toggle