Juniper CTP1000 Series Installation instructions

CTP1000 Series Circuit to Packet
Platforms
Hardware Guide
Modified: 2015-11-22
Copyright © 2015, Juniper Networks, Inc.

Juniper Networks, Inc.
1133 Innovation Way
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Copyright © 2015, Juniper Networks, Inc. All rights reserved.
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
CTP1000 Series Circuit to Packet Platforms Hardware Guide
Copyright © 2015, Juniper Networks, Inc.
All rights reserved.
Revision History
December 2015—Revision 1
The information in this document is current as of the date on the title page.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networks
software. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted at
http://www.juniper.net/support/eula.html. By downloading, installing or using such software, you agree to the terms and conditions of
that EULA.
Copyright © 2015, Juniper Networks, Inc.ii

Table of Contents
Part 1 Overview
Chapter 1 CTP1000 Series Platform Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IntroducingCTPPlatforms............................................3
CTP1002Platform...................................................3
CTP1004Platform...................................................5
CTP1012Platform....................................................7
Part 2 Planning
Chapter2 SystemSpecifications..............................................11
CTP1002 Platform Specifications and Certification . . . . . . . . . . . . . . . . . . . . . . . . . 11
CTP1004 Platform Specifications and Certification . . . . . . . . . . . . . . . . . . . . . . . . 14
CTP1012 Platform Specifications and Certification . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 3 Planning and Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
BeforeYouInstallaCTPPlatform......................................19
CTP1000 Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter4 EquipmentRackRequirements......................................21
CTP1000RackRequirements.........................................21
CTP1000MechanicalRequirements....................................21
CTP1000SpaceRequirements........................................22
CTP1000RackInstallation...........................................22
CTPCablingRecommendations.......................................22
Chapter 5 Cable and Pinout Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
CTP1000 Interface Module 100-to-25-Pin Cable Pinouts . . . . . . . . . . . . . . . . . . . 25
EIA-530 Connector Interface Signal Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RS-232 Connector Interface Signal Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . 26
VoiceInterfaceSignalPinouts.....................................27
T1InterfaceSignalPinouts........................................28
CTP1000ConsoleCablePinouts......................................29
CTPFastEthernetandPowerCables...................................29
FastEthernetCables............................................29
DCPowerCables...............................................29
Part 3 Safety
Chapter6 GeneralSafetyGuidelines..........................................33
CTPSafetyGuidelinesandWarnings...................................33
iiiCopyright © 2015, Juniper Networks, Inc.

Chapter7 HardwareCompliance.............................................35
Declaration of Conformity for CTP1000 Platforms . . . . . . . . . . . . . . . . . . . . . . . . 35
Federal Communications Commission (FCC) Statement . . . . . . . . . . . . . . . . . . . 36
FCC Requirements for Consumer Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Food and Drug Administration, Center for Devices and Radiological Health . . . . . 37
Compliance with Canadian Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
IndustryCanadaNotice..........................................38
IndustryCanadaNoticeCS-03.................................38
AvisCS-03d'IndustrieCanada.................................38
Canadian Department of Communications Explanatory Notes . . . . . . . . . . . 39
DOC Explanatory Notes: Equipment Attachment Limitations . . . . . . . . 39
Notes explicatives du ministère des Communications: limites visant les
accessoires.............................................40
Part 4 Installation
Chapter 8 Unpacking and Inspecting the CTP Platform . . . . . . . . . . . . . . . . . . . . . . . . . 43
BeforeYouUnpacktheCTPPlatform...................................43
UnpackingtheCTPDevice...........................................43
Inspecting Platform Components and Accessories . . . . . . . . . . . . . . . . . . . . . . . . 44
IfYouDetectorSuspectDamage......................................44
ContactingJuniperNetworks..........................................45
Chapter9 InstallingtheChassis..............................................47
Before You Install the CTP1000 Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Installing the CTP1000 Platform in Freestanding Mode . . . . . . . . . . . . . . . . . . . . 47
Installing the CTP1000 Platform in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chapter10 Cabling ..........................................................49
Cabling the CTP1000 Platform Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Required Tools, Wires, and Cables for the CTP1000 Platform . . . . . . . . . . . . . . . 49
CTPFastEthernetandPowerCables...................................50
FastEthernetCables............................................50
DCPowerCables...............................................50
Chapter11 PoweringOn......................................................51
Before You Power On the CTP1000 Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
PoweringOntheCTP1000Platform....................................51
PoweringOfftheCTPPlatform........................................54
Part 5 Configuration
Chapter 12 Accessing the CTP1000 Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Setting Up Management Access on the CTP1000 Platform . . . . . . . . . . . . . . . . . 57
CTP1000ConsolePortSetup.........................................57
Using HyperTerminal with the CTP1000 Platform . . . . . . . . . . . . . . . . . . . . . . . . . 58
Connecting Directly to the CTP1000 Platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
CTP1000PlatformSSHSetup........................................59
Copyright © 2015, Juniper Networks, Inc.iv
CTP1000 Series Hardware Guide

Part 6 Maintenance
Chapter13 Maintaining Components ..........................................63
CleaningtheCTPPlatform...........................................63
Required Tools for Maintaining the CTP Platform . . . . . . . . . . . . . . . . . . . . . . . . . 63
Storing CTP Modules and Other Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Chapter 14 Product Reclamation and Recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Product Reclamation and Recycling Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Chapter 15 Packing and Returning Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
ReturnProcedure...................................................67
Returning CTP Products for Repair or Replacement . . . . . . . . . . . . . . . . . . . . . . . 67
Part 7 Troubleshooting
Chapter 16 Troubleshooting Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
CTPPlatformDoesNotPowerOn......................................71
CTPPlatformShutsDown............................................71
Chapter17 ContactingCustomerSupport......................................73
ContactingCustomerSupport.........................................73
Locating CTP Component Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Information You Might Need to Supply to JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Part 8 Index
Index..........................................................77
vCopyright © 2015, Juniper Networks, Inc.
Table of Contents

Copyright © 2015, Juniper Networks, Inc.vi
CTP1000 Series Hardware Guide

List of Figures
Part 1 Overview
Chapter 1 CTP1000 Series Platform Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 1: CTP1002 Chassis (Front View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure2:CTP1002Chassis(RearView)..................................4
Figure 3: CTP1004 Platform (AC and DC Version, Front View) . . . . . . . . . . . . . . . . 5
Figure 4: CTP1004 Platform (AC Version, Rear View) . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5: CTP1004 Platform (DC Version, Rear View) . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 6: Wiring a CTP1004 Platform (DC Version) . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 7: CTP1012 Platform (AC Version, Front View) . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 8: CTP1012 Platform (AC Version, Rear View) . . . . . . . . . . . . . . . . . . . . . . . . 8
Part 3 Safety
Chapter7 HardwareCompliance.............................................35
Figure 9: CTP1000 Platforms Declaration of Conformity . . . . . . . . . . . . . . . . . . . . 36
viiCopyright © 2015, Juniper Networks, Inc.

Copyright © 2015, Juniper Networks, Inc.viii
CTP1000 Series Hardware Guide

List of Tables
Part 2 Planning
Chapter2 SystemSpecifications..............................................11
Table 1: CTP1002 Platform Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 2: CTP1004 Platform Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 3: CTP1012 Platform Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 5 Cable and Pinout Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 4: EIA-530 Connector Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 5: RS-232 Connector Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table6:VoiceInterfaceSignals........................................27
Table7:T1InterfaceSignals...........................................28
Table 8: CTP1000 Series Console Cable Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Part 4 Installation
Chapter10 Cabling ..........................................................49
Table9:RequiredCables.............................................50
ixCopyright © 2015, Juniper Networks, Inc.

Copyright © 2015, Juniper Networks, Inc.x
CTP1000 Series Hardware Guide

PART 1
Overview
•CTP1000 Series Platform Overview on page 3
1Copyright © 2015, Juniper Networks, Inc.

Copyright © 2015, Juniper Networks, Inc.2
CTP1000 Series Hardware Guide

CHAPTER 1
CTP1000 Series Platform Overview
•Introducing CTP Platforms on page 3
•CTP1002 Platform on page 3
•CTP1004 Platform on page 5
•CTP1012 Platform on page 7
Introducing CTP Platforms
Juniper Networks CTP Series Circuit to Packet platforms provide advanced technology
and features required to reliably transport legacy time-division multiplexing (TDM) and
other circuit-based applications across next-generation IP networks. CTP platforms
create an IP packet flow from a serial data or analog voice connection at one end and
provide the necessary processing to re-create the serial bit stream or analog signal from
the received packet flow at the other end.
CTP platforms provide compact and lightweight chassis, high port density, and multiple
Ethernet interfaces. Each CTP platform runs the CTP operating system (CTPOS) and
can be managed by the Juniper Networks CTPView Network Management System, a
secure, Web-based management tool for provisioning, managing, running diagnostics,
monitoring, and reporting on all CTP devices and circuits in the network.
CTP1002 Platform
The Juniper Networks CTP1002 Circuit to Packet platform is a 1-U high, half-rack wide
chassis designed for tabletop or shelf installation. It can also be installed in a rack with
the supplied rack-mounting kit. The CTP1002 platform does not have any removable
interface modules or cooling fans, but does use a removable Type II CompactFlash card.
It is available in an AC-powered version only. See Figure 1 on page 3.
Figure 1: CTP1002 Chassis (Front View)
The front panel comprises the following components (see Figure 1 on page 3):
3Copyright © 2015, Juniper Networks, Inc.

•Power LED—Green when power is connected and the power switch is set to the ON
position.
•HDD LED—Red when the drive is in use.
•Front power switch—Set to ON position when 1is briefly pressed. Set to OFF when 1is
pressed for four or more seconds.
•Removable flash drive—The device must be powered off when you insert or remove
the flash drive.
The rear panel comprises the following components (see Figure 2 on page 4):
Figure 2: CTP1002 Chassis (Rear View)
External Reference Input
BNC or DB=9
SE-0/0 SE-0/1
Ethernet
USB
Console
g015351
•Power input from the external 12-VDC power supply.
•Port 0 and port 1 DB-25 connectors—DB-25 connectors are used for terminating EIA530,
RS-232, V.35, 4WTO, and T1 circuits.
The DB-25 port connector pinout is the same as the quad cables used on the larger
CTP platforms. See“CTP1000 Interface Module 100-to-25-Pin Cable Pinouts” on
page 25 to find pinout information for this connector.
•COM 2 console connection—Provides an asynchronous TTY connection for local
configuration of the CTP platform. See “CTP1000 Console Cable Pinouts” on page 29
to find pinout information for this connector.
•Fast Ethernet connector—Provides the 100-Mbps Ethernet connection to the IP network
by means of a local Ethernet switch or router.
•USB port.
Related
Documentation
CTP1004 Platform on page 5•
•CTP1012 Platform on page 7
Copyright © 2015, Juniper Networks, Inc.4
CTP1000 Series Hardware Guide

CTP1004 Platform
The CTP1004 platform is a 1-U high, full-rack wide chassis designed for tabletop or shelf
installation. It can also be installed in a rack with the supplied rack-mounting kit. The
CTP1004 device does not have any removable interface modules, but does use a
removable Type II CompactFlash card and is available in both AC-powered and
DC-powered versions. It has multiple cooling fans, and airflow is front to back. See
Figure 3 on page 5,Figure 4 on page 6, and Figure 5 on page 6.
Figure 3: CTP1004 Platform (AC and DC Version, Front View)
H D P O W E R C T P 100 4
g015371
Power switch USBFlash drive
The front panel comprises the following components (see Figure 3 on page 5):
•Power LED—Green when power is connected and the power switch is set to the ON
position.
•HDD LED—Red when the flash card is in use.
•Front power switch—Set to ON position when 1is briefly pressed. Set to OFF when 1is
pressed for four or more seconds.
•Removable flash card—The device must be powered off when you insert or remove
the flash card.
•USB ports.
The rear panel comprises the following components (see Figure 4 on page 6 and
Figure 5 on page 6):
•Power supply—Uses a standard IEC power cord for the AC version. Uses a 18-AWG
fork terminal connector for the DC version. There is no power redundancy for the DC
version.
•Ethernet connection—Provides the 100-Mbps Ethernet connection to the IP network
by means of a local Ethernet switch or router.
•Console connection—Provides an asynchronous TTY connection for locally configuring
the CTP device. See “CTP1000 Console Cable Pinouts” on page 29 to find pinout
information for this connector.
•Interface connector—Features a 100-pin connector providing four serial interfaces
when used with the CTP quad cable. See“CTP1000 Interface Module 100-to-25-Pin
Cable Pinouts” on page 25 to find pinout information for this connector.
•USB ports.
5Copyright © 2015, Juniper Networks, Inc.
Chapter 1: CTP1000 Series Platform Overview

Figure 4: CTP1004 Platform (AC Version, Rear View)
. . . .
. . . . .
External reference input
BNC or DB=9
Console ETH0 ETH1
g015372
Ethernet USB
USBFan
Power switch and connection
BNC
Interface module
CTP1004 (Version 1)
CTP1004 (Version 2)
Console Fan Power switch and connection
Interface module
Figure 5: CTP1004 Platform (DC Version, Rear View)
Fan Power switch
Terminal block
(Insert wires from bottom. Do not remove screws.)
USBConsole
ETH2
ETH1 Interface module
ETH0
. . . .
. . . . .
External reference input
BNC or DB-9
g015373
NOTE: Do not remove the screws or the protective cover for the DC power
terminal when cabling for power (see Figure 6 on page 7). Use a magnetic
screwdriver to loosen the two inner screws two to three turns.
Slide the fork terminal connectors up through the bottom of the protective
cover. If you install the wires from the top, they will block the power switch.
Copyright © 2015, Juniper Networks, Inc.6
CTP1000 Series Hardware Guide

Figure 6: Wiring a CTP1004 Platform (DC Version)
Power switch
•Do not remove screws or cover.
•Use a magnetic screwdriver and
loosen only two to three turns.
•Insert wires from bottom.
Fork terminal connectors
g015374
Related
Documentation
CTP1002 Platform on page 3•
•CTP1012 Platform on page 7
CTP1012 Platform
The CTP1012 platform is a 1-U high, full-rack wide chassis designed for tabletop or shelf
installation. It can also be installed in a rack with the supplied rack-mounting kit. The
CTP1012 device does not have any removable interface modules, but does use a removable
Type II CompactFlash card and is available in an AC-powered version. It has multiple
cooling fans, and airflow is front to back. See Figure 7 on page 7 and Figure 8 on page 8.
Figure 7: CTP1012 Platform (AC Version, Front View)
HD P O W E R C T P 10 12
g015379
Power switch USBFlash drive
The front panel comprises the following components (see Figure 7 on page 7):
•Power LED—Green when power is connected and the power switch is set to the ON
position.
•HDD LED—Red when the flash card is in use.
•Front power switch—Set to ON position when 1is briefly pressed. Set to OFF when 1is
pressed for four or more seconds.
•Removable flash card—The device must be powered off when you insert or remove
the flash card.
•USB ports.
The rear panel comprises the following components (See Figure 8 on page 8):
•Power supply—Uses a standard IEC power cord.
•Ethernet connection—Provides the 100-Mbps Ethernet connection to the IP network
by means of a local Ethernet switch or router.
7Copyright © 2015, Juniper Networks, Inc.
Chapter 1: CTP1000 Series Platform Overview

•Console connection—Provides an asynchronous TTY connection for locally configuring
the CTP device. See “CTP1000 Console Cable Pinouts” on page 29 to find pinout
information for this connector.
•Interface connector—Features a 100-pin connector providing four serial interfaces
when used with the CTP quad cable. See“CTP1000 Interface Module 100-to-25-Pin
Cable Pinouts” on page 25 to find pinout information for this connector.
•USB ports.
Figure 8: CTP1012 Platform (AC Version, Rear View)
SE-1/0-3 SE-2/0-3
SE-0/0-3 USB
Console Fan
Ethernet
Power Switch and Connection
. . . .
. . . . .
External reference input
BNC or DB=9
g015352
Related
Documentation
•CTP1002 Platform on page 3
•CTP1004 Platform on page 5
Copyright © 2015, Juniper Networks, Inc.8
CTP1000 Series Hardware Guide

PART 2
Planning
•System Specifications on page 11
•Planning and Preparing the Site on page 19
•Equipment Rack Requirements on page 21
•Cable and Pinout Specifications on page 25
9Copyright © 2015, Juniper Networks, Inc.

Copyright © 2015, Juniper Networks, Inc.10
CTP1000 Series Hardware Guide