Juniper E SERIES BROADBAND SERVICES ROUTERS - E SERIES END-OF-LIFE MODULE GUIDE... User manual

E Series™ Broadband
Services Routers
E Series™ End-of-Life Module Guide
Published: 2010-10-06
Copyright © 2010, Juniper Networks, Inc.

This guide provides an overview and description of E Series modules that are end-of-life
(EOL) and can no longer be ordered for the following routers:
•ERX7xx models
•ERX14xx models
•ERX310 router
•E120 router
•E320 router
Depending on the EOL schedule of a module, new software releases might not support
the module.
Table 1 on page 3 lists EOL modules alphabetically. It lists EOL modules for ERX routers
first and then for E120 and E320 routers.
NOTE: Any future JunosE release number provided in the Actual or Predicted
Last JunosE Support field of Table 1 on page 3 is based on the current JunosE
release schedule. If the release schedule changes in the future, Juniper
Networks will update the associated Product Support Notification (PSN)
Technical Bulletin for any affected EOL modules.
For more information about E Series routers and modules, refer to the following guides:
•ERX module installation and maintenance—ERX Hardware Guide
•E120 and E320 module installation and maintenance—E120 and E320 Hardware Guide
•Managing E Series routers—JunosE System Basics Configuration Guide
•Configuring E Series modules—JunosE Link Layer Configuration Guide
To obtain the most current list of EOL modules, see the End-of-Life Products page on
the Juniper Networks Web site at http://www.juniper.net/support/eol.
Copyright © 2010, Juniper Networks, Inc.2
E Series End-of-Life Module Guide

Table 1: End-of-Life Modules
Page
Actual or
Predicted
Last
JunosE
Support
First
JunosE
Support
I/O Module
Label
Line Module
LabelCombination Name
ERX ROUTER MODULES
CE1
87.3.x1.1.0CE1 FULL I/OCE1CE1
Channelized OC3/STM1
915.0.x2.2.0cOC3 STM1 F0
I/O
MULTIMODE
cOCx/STMx F0cOC3/STM1 multimode
1115.0.x2.2.0cOC3 STM1 F0
I/O
SINGLE MODE
cOCx/STMx F0cOC3/STM1 single-mode
intermediate reach
1315.0.x2.2.0cOC3 STM1 F0
I/O
LONG HAUL
cOCx/STMx F0cOC3/STM1 single-mode
long reach
Channelized OC12/STM4
1515.0.x2.2.0cOC12 STM4 F0
I/O
MULTI MODE
cOCx/STMx F0cOC12/STM4 multimode
without APS/MSP
redundancy
1715.0.x2.2.0cOC12 STM4 F0
I/O
SINGLE MODE
cOCx/STMx F0cOC12/STM4
single-mode
intermediate reach
without APS/MSP
redundancy
1915.0.x6.1.3,
7.0.2,
7.2.0
COC12 F0 APS
SINGLE MODE
cOCx/STMx F0cOC12/STM4
single-mode
intermediate reach with
APS/MSP redundancy
2115.0.x2.2.0cOC12 STM4
LONG HAUL
cOCx/STMx F0cOC12/STM4
single-mode long reach
Channelized T1
237.3.x1.1.0CT1 FULL I/OCT1CT1
Channelized T3
3Copyright © 2010, Juniper Networks, Inc.

Table 1: End-of-Life Modules (continued)
Page
Actual or
Predicted
Last
JunosE
Support
First
JunosE
Support
I/O Module
Label
Line Module
LabelCombination Name
247.0.x1.0.0CT3/T3 I/OCT3CT3 (3 ports)
2514.0.x3.2.0CT3/T3 12 I/OCT3/T3-F0CT3/T3 12 (12 ports)
E3
267.1.x1.1.0E3 I/OE3 ATME3 ATM
277.0.x1.1.0E3 I/OE3 FRAMEE3 Frame (3 ports)
2814.0.x4.0.2E3-12
FRAME I/O
COCX-F3E3 Frame (12 ports)
Fast Ethernet
297.0.x1.3.0FE-2 I/OFE-2FE-2 (2 ports)
305.2.x2.0.0FE-8 I/OGE/FEFE-8 (8 ports) (128 MB)
Only line module is EOL.
Gigabit Ethernet (1–port)
315.2.x2.0.0GE I/O SFPGE/FEGE 1000Base-LH
(128 MB)
Only line module is EOL.
335.2.x2.0.0GE I/O SFPGE/FEGE 1000Base-SX
(128 MB)
Only line module is EOL.
355.2.x2.0.0GE I/O SFPGE/FEGE 1000Base-ZX
(128 MB)
Only line module is EOL.
HSSI
377.3.x3.1.0HSSI-3 I/OHSSI-3FHSSI
IPSec Service
3814.0.x4.0.2No I/O moduleIPSEC
SERVICE
IPSec Service
OC3/STM1
Copyright © 2010, Juniper Networks, Inc.4
E Series End-of-Life Module Guide

Table 1: End-of-Life Modules (continued)
Page
Actual or
Predicted
Last
JunosE
Support
First
JunosE
Support
I/O Module
Label
Line Module
LabelCombination Name
394.1.x1.0.0OC3 I/O
MULTI MODE
OC3OC3 (dual-port)
multimode
404.1.x1.0.0OC3 I/O
SINGLE MODE
OC3OC3 (dual-port)
single-mode
OC3/STM1 ATM
415.2.x2.0.0OC3-4 I/O
MULTI MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM
multimode without
APS/MSP redundancy
(128 MB)
Only line module is EOL.
435.2.x2.0.0OC3-4 I/O
SINGLE MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM
single-mode
intermediate reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
455.2.x2.0.0OC3-4 I/O
LONG HAUL
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC3/STM1 ATM
single-mode long reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
OC12/STM4 ATM
475.2.x2.0.0OC12 STM4 I/O
MULTI MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM
multimode without
APS/MSP redundancy
(128 MB)
Only line module is EOL.
495.2.x2.0.0OC12 STM4 I/O
SINGLE MODE
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM
single-mode
intermediate reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
5Copyright © 2010, Juniper Networks, Inc.

Table 1: End-of-Life Modules (continued)
Page
Actual or
Predicted
Last
JunosE
Support
First
JunosE
Support
I/O Module
Label
Line Module
LabelCombination Name
515.2.x2.0.0OC12 STM4 I/O
LONG HAUL
OCx/STMx
ATM or
OCx/STMx
/DS3-ATM
OC12/STM4 ATM
single-mode long reach
without APS/MSP
redundancy (128 MB)
Only line module is EOL.
SRPs
535.2.x1.0.0SRP I/OSRP-5GSRP-5G (512 MB)
548.0.x3.0.2SRP I/OSRP-5G+SRP-5G+ (512 MB)
5514.0.x4.1.3,
5.0.4,
5.1.2,
5.2.0
SRP I/OSRP-5G+SRP-5G+ (2-GB
memory)
565.2.x1.1.0SRP I/OSRP-10GSRP-10G (512 MB)
578.0.x4.1.3,
5.0.4,
5.1.2,
5.2.0
SRP I/OSRP-10GSRP-10G (1-GB memory)
587.1.x5.1.0SRP-SE I/OSRP-SE10GSRP-SE10G (512 MB)
595.2.x3.4.1SRP I/OSRP-40GSRP-40G (512 MB)
607.1.x4.0.0SRP I/OSRP-40G
PLUS
SRP-40G PLUS (1 GB)
T3
617.0.x1.1.0CT3/T3 I/OT3 ATMT3 ATM (3 ports)
625.2.x4.1.04xDS3 ATM I/OOCx/STMx
ATM or
OCx/STMx
/DS3-ATM
T3 ATM (4 ports)
(128 MB)
Only line module is EOL.
637.0.x1.1.0CT3/T3 I/OT3 FRAMET3 Frame (3 ports)
6414.0.x4.0.2CT3/T3 12 I/OCOCX-F3T3 Frame (12 ports)
Tunnel Service Module (TSM)
Copyright © 2010, Juniper Networks, Inc.6
E Series End-of-Life Module Guide

Table 1: End-of-Life Modules (continued)
Page
Actual or
Predicted
Last
JunosE
Support
First
JunosE
Support
I/O Module
Label
Line Module
LabelCombination Name
658.0.x3.0.2No I/O moduleTUNNEL
SERVICE
TSM
X.21/V.35
667.3.x2.10.1,
3.3.2
X.21/V.35 I/OX.21/V.35X.21/V.35
E120 and E320 ROUTER MODULES
Gigabit Ethernet IOA
6814.0.x7.0.1ES2-S1
10GE
IOA
ES2-S1
10GE
IOA
10GE IOA
7Copyright © 2010, Juniper Networks, Inc.

CE1 Module Combination
CE1
Line module label
CE1 FULL I/O
I/O module label
•20
Number of I/O ports
•First supported: 1.1.0
•Final supported: 7.3.x
Software release
•40 W
•Channelized E1
Description
•Non-ASIC
Type
•E1
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Software features
•ERX7xx models
•ERX1410 router
Model compatibility
•SRP-5G
•SRP-5G+
•SRP-10G
SRP module compatibility
•1:N redundancy
Module redundancy support
•RJ-48C,120 ohm
•BNC, 75-ohm via a balun panel that connects to the I/O module
•Use shielded cables to maintain EMC compliance.
•The transmitted signal complies with ITUT G.703, Physical/electrical
characteristics of hierarchical digital interfaces (November 2001) for cable
lengths up to 450 m (492 yards).
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in the Configuring Channelized T1 and Channelized E1
Interfaces chapter of the JunosE Physical Layer Configuration Guide for Release
8.0.x and earlier.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.8
E Series End-of-Life Module Guide

cOC3/STM1 Multimode Module Combination
cOCx/STMx F0
Line module label
cOC3 STM1 F0 I/O
MULTI MODE
I/O module label
•4
Number of I/O ports
•First supported: 2.2.0
•Final supported: 15.0.x
Software release
•130 W
•OC3/STM1 channelized to DS3, DS1, E1, and DS0
•Supports either E1 or T1 operation, but not E1 and T1 operation simultaneously
Description
•EFA ASIC
Type
•OC3/STM1
•DS3
•T1, E1
•DS0
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information about
the layer 2 and layer 3 protocols and applications that this module combination
supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•1:N redundancy
•NOTE: Line module redundancy is not supported on the ERX310 router.
Module redundancy support
9Copyright © 2010, Juniper Networks, Inc.
cOC3/STM1 Multimode Module Combination

•Up to four SC full duplex connectors
•Tx power:
•min: –19 dBm
•max: –14 dBm
•Center wavelength: 1310 nm
•Rx input power:
•min: –30 dBm
•max: –14 dBm
•Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of
0–9 dB or 50-micron core cable with an optical loss of 7 dB
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.10
E Series End-of-Life Module Guide

cOC3/STM1 Single-Mode Intermediate Reach Module Combination
cOCx/STMx F0
Line module label
cOC3 STM1 F0 I/O
SINGLE MODE
I/O module label
•4
Number of I/O ports
•First supported: 2.2.0
•Final supported: 15.0.x
Software release
•130 W
•OC3/STM1 channelized to DS3, DS1, E1, and DS0
Description
•EFA ASIC
Type
•OC3/STM1
•DS3, DS1
•T1, E1
•DS0
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•1:N redundancy
•NOTE: Line module redundancy is not supported on the ERX310 router.
Module redundancy support
11Copyright © 2010, Juniper Networks, Inc.
cOC3/STM1 Single-Mode Intermediate Reach Module Combination

•Up to four SC full duplex connectors
•Tx power:
•min: –15 dBm
•max: –8 dBm
•Center wavelength: 1310 nm
•Rx input power:
•min: –31 dBm
•max: –8 dBm
•Rated for 15 km (9.3 miles) of 9-micron core cable
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.12
E Series End-of-Life Module Guide

cOC3/STM1 Single-Mode Long Reach Module Combination
cOCx/STMx F0
Line module label
cOC3 STM1 F0 I/O
LONG HAUL
I/O module label
•4
Number of I/O ports
•First supported: 2.2.0
•Final supported: 15.0.x
Software release
•130 W
•OC3/STM1 channelized to DS3, DS1, E1, and DS0
Description
•EFA ASIC
Type
•OC3/STM1
•DS3, DS1
•T1, E1
•DS0
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•1:N redundancy
•NOTE: Line module redundancy is not supported on the ERX310 router.
Module redundancy support
13Copyright © 2010, Juniper Networks, Inc.
cOC3/STM1 Single-Mode Long Reach Module Combination

•Up to four SC full duplex connectors
•Tx power:
•min: –5.0 dBm
•max: 0 dBm
•Center wavelength: 1310 nm
•Rx input power:
•min: –34 dBm
•max: –7 dBm
•Fiber type: 9-micron core
•Rated for 40 km (24.8 miles) of 9-micron core cable
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.14
E Series End-of-Life Module Guide

cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination
cOCx/STMx F0
Line module label
cOC12 STM4 F0 I/O
MULTI MODE
I/O module label
•1
Number of I/O ports
•First supported: 2.2.0
•Final supported: 15.0.x
Software release
•130 W
•OC12/STM4 channelized to DS3, DS1, E1, and DS0
Description
•EFA ASIC
Type
•OC12/STM4
•OC3/STM1
•DS3, DS1
•T1, E1
•DS0
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information about
the layer 2 and layer 3 protocols and applications that this module combination
supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•1:N redundancy
•NOTE: Line module redundancy is not supported on the ERX310 router.
Module redundancy support
15Copyright © 2010, Juniper Networks, Inc.
cOC12/STM4 Multimode Without APS/MSP Redundancy Module Combination

•SC full duplex connector
•Tx power:
•min: –19 dBm
•max: –14 dBm
•Center wavelength: 1310 nm
•Rx input power:
•min: –30 dBm
•max: –14 dBm
•Rated for 2 km (1.2 miles) over 62.5-micron core cable with an optical loss of 0–9
dB or 50-micron core cable with an optical loss of 7 dB
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.16
E Series End-of-Life Module Guide

cOC12/STM4 Single-Mode Intermediate Reach Without APS/MSP Redundancy Module
Combination
cOCx/STMx F0
Line module label
cOC12 STM4 F0 I/O
SINGLE MODE
I/O module label
•1
Number of I/O ports
•First supported: 2.2.0
•Final supported: Not applicable
Software release
•130 W
•OC12/STM4 channelized to DS3, DS1, E1, and DS0
Description
•EFA ASIC
Type
•OC12/STM4
•OC3/STM1
•DS3, DS1
•T1, E1
•DS0
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information
about the layer 2 and layer 3 protocols and applications that this module
combination supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•1:N redundancy
•NOTE: Line module redundancy is not supported on the ERX310 router.
Module redundancy support
17Copyright © 2010, Juniper Networks, Inc.
cOC12/STM4 Single-Mode Intermediate Reach Without APS/MSP Redundancy Module Combination

•SC full duplex connector
•Tx power:
•min: –15 dBm
•max: –8 dBm
•Center wavelength: 1310 nm
•Rx input power:
•min: –31 dBm
•max: –8 dBm
•Rated for 15 km (9.3 miles) of 9-micron core cable
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.18
E Series End-of-Life Module Guide

cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module
Combination
cOCx/STMx F0
Line module label
COC12 F0 APS
SINGLE MODE
I/O module label
•2
•1 active, 1 redundant
Number of I/O ports
•First supported: 6.1.3 or later 6.1.x release, 7.0.2 or later 7.0.x release, 7.2.0 and
higher-numbered release
•Final supported: 15.0.x
Software release
•130 W
•OC12/STM4 channelized to DS3, DS1, E1, and DS0
Description
•EFA ASIC
Type
•OC12/STM4
•OC3/STM1
•DS3, DS1
•T1, E1
•DS0
•HDLC framing
Capability
•See ERX Module Guide, Appendix A, Module Protocol Support for information about
the layer 2 and layer 3 protocols and applications that this module combination
supports.
Software features
•ERX7xx models
•ERX14xx models
•ERX310 router
Model compatibility
•SRP-5G+
•SRP-10G
•SRP-40G
•SRP-40G PLUS
•SRP-SE10G
SRP module compatibility
•1:N redundancy
•NOTE: Line module redundancy is not supported on the ERX310 router.
Module redundancy support
19Copyright © 2010, Juniper Networks, Inc.
cOC12/STM4 Single-Mode Intermediate Reach With APS/MSP Redundancy Module Combination

•SC full duplex connector
•Tx power:
•min: –15 dBm
•max: –8 dBm
•Center wavelength: 1310 nm
•Rx input power:
•min: –31 dBm
•max: –7 dBm
•Rated for 15 km (9.3 miles) of 9-micron core cable
•See ERX Hardware Guide, Chapter 5, Cabling ERX Routers for more information.
Cables and connectors
•See ERX Module Guide, Appendix B, Module LEDs.
LEDs
•See Monitoring Interfaces in JunosE Physical Layer Configuration Guide, Chapter 4,
Configuring Channelized OCx/STMx Interfaces.
Alarms, errors, and events
Copyright © 2010, Juniper Networks, Inc.20
E Series End-of-Life Module Guide