JustFire EC10 User manual

Monoblock Klimagerät EC 10
Climatiseur Monobloc EC 10
Aria condizionata Monobloc EC 10
Y.

This product can be connected only to a
supply with system impedance no more than
0.193 ohm. In case necessary, please consult
your supply authority for system impedance
information.
The air conditioner is delivered in a protective
packaging and is accompained by an instruction
manual. This manual is an integral part of the air
conditioner and should therefore be carefully
read and preserved. When the air conditioner is
unpacked, please check that the air conditioner
and accessory packed are complete and
undamaged.
Be fully aware of the weight of the air conditioner
before attempting to lift it. Take all necessary
precautions to avoid damaging the product or
causing personal injury. It is advisable to remove
the packaging only when the air conditioner has
been located in the point of installation. Carefully
remove the adhesive strips positioned on the air
adhesive. Packaging components must be tidied
up correctly and not left within reach of children,
since they are hiding of danger.
This product has been manufactured to
comply with 2006/95/EC and with
amendments 92/31/EEC and 93/68/EEC.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice.
Any batteries used in the remote control
contain materials, which are hazardous to
the environment, They must be removed
from the remote control when they reach the
end of their life and disposed of responsibly.
1. FASTENING BRACKET
2. REMOTE CONTROL
3. REMOTE CONTROL HOLDER
4. DRAINAGE PIPE
5. EXTERNAL GRATING
6. PLASTIC SHEET AIR PIPE
7. KIT OF SCREWS
8. GRATING FIXING CORD
9. INSTRUCTION MANUAL
10. PAPER TEMPLATE FOR WALL DRILLING
(See page)
11. 160mm RING
12. 150mm RING
1.GENERAL INFORMATION ENGLISH
1.3 RECEIVING THE GOODS
1.4 HANDLING
1.5 LIST OF ACCESSORIES(P0)
2
P0
1
2
3
4
5
5
6
9
12
11
7
8
6
10

EC 10
2971
2874
932
850+2000
3.7+8.7
1890
50

2m
P3
2m
Outdoor Indoor
P4
spirit level

26mm
455mm
FRESH AIR HOLE(OPTIONAL)
52mm
O

P5
3° INCLINATION
P13
Soft terminal
Hard terminal
A
A
B
B
System "A" is more common use , and the
discharge pipe go outside where there is
no problem to connect or to discharge it ,
this solution is OK for hot country and
normal cold temperature out side .
FRESH AIR HOLE
- For the fresh air hole, the diameter would be
52mm. It is optional for the customer.

ENGLISH
2.INSTALLATION
2.4 FASTENING THE BRACKET(P6)
Drill the holes for anchoring the fastening bracket
to the wall using preferably the 6 holes showed in
black on the paper template. If the wall is not
sturdy enough it is advisable to use extra anchor
bolts using the holes showed in grey on the paper
template.
The anchor bolts provided require a 8mm holes;
the wall should be inspected to determine if
provided bolts are useful or if it is necessary to
use a different anchorage. The manufacturer
is not liable in case of underestimation of the
structural consistency of the anchorage made
at the time of installation.
2.5 INSTALLATION OF THE PIPES
(P20)
After drilling the holes, the plastic sheet supplied
with the air conditioner need to be fitted through
them.
Measure the depth of the wall and cut supplied
plastic sheet.
Roll the sheet and insert it into the hole, paying
attention to the joint line, which must be always
upper position. Remember that the sheet must
0
have the same inclination of the holes(min 3 ).
Insert the rings into the holes.
7
System “B”: in case of impossibility to install the
drainage pipa as showed on “A” system, please
use system “B” to drain the condensate moisture
to a suitable place.
If use system “B”, please do not unplug the black
rubber cup from system “A”.
Usually “B” hole is used in the installation when
the outside temperature is very low, and in this
way we prevent no ice in the discharge water
pipe. This solution is used also to be more easy
for the installer to connect the internal drainage
pipe when he don’t want to see the pipe from
outside.
P6
P20
150mm ring 160mm ring

P7
P8
P10
P9

LIFT IT UP
HERE
P11
P12
LIFT IT UP
HERE Water
P14
Water cap

Press the ON/OFF button " ", switch on the
air conditioner, it will run by memory mode.
Press the MODE button " " set up the
mode to fan " ", the air conditioner will
run in fan.
Press UP " " or DOWN " " button, to
adjust the setting up temperature.
Press the FAN SPEED button " ", set up
the fan speed. is low speed, is middle
speed, is high speed, (flashing) is auto
speed.
Fan auto fan, the speed is choosen by the
difference of room temperature and setting
temperature.
Room temperature-setting temperature＞5℃,
high speed.
Room temperature-setting temperature＞3℃,
middle speed.
Room temperature-setting temperature＞1℃,
low speed.
Press the ON/OFF button " ", switch off
the air conditioner. Next time when this
button is pressed, the air conditioner will
operates in this mode by memory.

There is fresh air system in the back of the unit. On the wall, the fresh air pipe
would be 50mm accordingly.The air conditioner will change the room air
automatically, in this way new clean and fresh air will intake to the room.
Same time,the air conditioner performance would be lower.
The filter should be cleaned regularly to keep the fresh air flow smoothly.Take out
the filter as the arrow direction, wash it (not use hot water) and only when it is dried
replace it in same way.
ATTENTION: Do not use the air conditioner without the filter.
Fresh air filter
O50
Fresh air pipe

LIFT IT UP
HERE
LIFT IT UP
HERE
P15
P16
P17
P19
P18