JVC GY-HM200 User manual

1B5A-1103-00
This is a notification on the changes or additions to the features and
changes in the onscreen display. Please read this together with the
“INSTRUCTIONS”.
K, M: Feature available on the model or series name only.
Bit Rate added to System “4K”
“70M” is added to [System] N [Record Set] N [Record Format] N [Bit Rate].
Memo :
●When 4K is set, the network function cannot be used.
Usable Cards
Format Setting and Usable SD Card Combinations
Estimated Recordable Time of SD Cards
●When [System]N[Record Set]N[Record Format]N[Format] is set to
“QuickTime”.
(Unit: minute)
Histogram feature added
The histogram shows the brightness distribution, and is employed
mainly for checking the exposure of the image.
1. Set the histogram feature to ON.
●Set [Main Menu]N[LCD / VF]N[Display Settings]N[Histogram]
to On.
●You can also press the user button that is assigned with
“Histogram”.
2. Set the upper and lower limits of the histogram display.
After setting, the brightness level is displayed in red color.
Icon display added when zebra function is “On”
During zebra pattern display, (zebra icon) is displayed on the
display screen in Camera mode.
Setting items changed or added to menu item [Rec Trigger]
Setting items in [A/V Set] N [Video Set] N [HDMI/SDI Out] N [Rec Trigger]
are changed. (K)
Setting items are added to
[A/V Set] N [Video Set] N [HDMI Out] N [Rec
Trigger]. (M)
●HDMI (K):
Superimposes the trigger signals in tandem with the [HDMI]
terminal as well as the [REC] button on the camera body and
outputs the recording/stop control signals to the compatible device.
●On (M):
Superimposes the trigger signals in tandem with the [HDMI]
terminal as well as the [REC] button on the camera body and
outputs the recording/stop control signals to the compatible device.
●SDI (K):
Superimposes the trigger signals in tandem with the [SDI OUT]
terminal as well as the [REC] button on the camera body and
outputs the recording/stop control signals to the compatible device.
●
HDMI+SDI ( K ):
Superimposes the trigger signals in tandem with the [HDMI/SDI Out]
terminal as well as the [REC] button on the camera body and outputs
the recording/stop control signals to the compatible device.
[Setting Values: ROff, HDMI, SDI, HDMI+SDI] (K)
[Setting Values: ROff,On] (M)
Memo :
● When [A/V Set] N [Video Set] N [HDMI/SDI Out] ( K ) or [HDMI Out] ( M )
is set to “Off”, [Rec Trigger] is fixed at “Off” and selection is disabled.
●When [System]N[Record Set]N[Rec Mode] is set to “Interval Rec” or
“Frame Rec”, [Rec Trigger] is fixed at “Off” and selection is disabled.
●Set to “Off” when connecting to a device that does not support record
trigger.
Bit Rate added to live streaming (K)
Setting values are added to [System]N[Network] / [Settings]N[Live
Streaming Set]N[Frame & Bit Rate]
GY-HM200/GY-HM170 INSTRUCTIONS
Notification of Changes
System Format Resolution Frame Rate
Bit Rate
(new values are in
bold)
4K Quick
Time 3840x2160
30p
25p
24p
150 M
70 M
System Format Bit Rate Usable SD Card
4K Quick
Time
150 M UHS-I U3 or higher
70 M Class 10 or higher
HD
50 M (YUV422),
50 M (XHQ)
35 M (UHQ) Class 6 or higher
AVCHD - Class 4 or higher
SD - -
Web - -
System 4K HD SD Web
Resolution 2160p 1080i/1080p 480i/
576i 540p270p
Bit Rate 150 M 70 M XHQ UHQ - HQ LP
4GB 3 6 9 12 47 130 285
8GB 6 13 18 25 95 270 580
16GB 12 26 36 50 190 540 1160
32GB 25 52 72 100 380 1080 2320
64GB
(SDXC) 50 105 145 200 760 2160 4720
128GB
(SDXC) 100 210 290 400 1520 4320 9440
Item Settings Options
Top Sets the maximum brightness
limit for changing the
histogram display color
5% to 110%
(in 5 % increments)
Default value: 80%
Bottom Sets the minimum brightness
limit for changing the
histogram display color
0 % to 105 %
(in 5 % increments)
Default value: 20%
Example 1) Top 110 %, Bottom 0 % Example 2) Top 90 %, Bottom 10 %
* The area in red is not displayed.
How to read the histogram
● The vertical axis denotes the number of pixels.
● The horizontal axis denotes the pixel brightness.
No. of
Frames for
Frame &
Bit Rate
Resolution New values are in bold
60i, 60p,
30p
1920x1080 60i (12 Mbps), R60i (8 Mbps),
60i (5 Mbps), 60i (3 Mbps)
1280x720 30p (8 Mbps), R30p (5 Mbps),
30p (3 Mbps), 30p (1.5 Mbps)
720x480
60i (8 Mbps), 60i (5 Mbps), R 60i (3 Mbps),
60i (1.5 Mbps), 60i (0.8 Mbps), 60i (0.3 Mbps)
640x360 30p (3 Mbps), R30p (1.5 Mbps),
30p (0.8 Mbps), 30p (0.3 Mbps)
50i, 50p,
25p
1920x1080 50i (12 Mbps), R50i (8 Mbps),
50i (5 Mbps), 50i (3 Mbps)
1280x720 25p (8 Mbps), R25p (5 Mbps),
25p (3 Mbps), 25p (1.5 Mbps)
720x576
50i (8 Mbps), 50i (5 Mbps), R 50i (3 Mbps),
50i (1.5 Mbps), 50i (0.8 Mbps), 50i (0.3 Mbps)
640x360 25p (3 Mbps), R25p (1.5 Mbps),
25p (0.8 Mbps), 25p (0.3 Mbps)
P 13000KP 13000K
F1.6F1.6
0dB0dB
AE+6AE+6
ND 1/16ND 1/16
12:34:5612:34:56
Jan 24,2015Jan 24,2015
00:00:00.0000:00:00.00
5.5.6 f t
100min100min
50min50min
282min282min
1/1001/100
1/1001/100
F1.6F1.6
0dB0dB
AE+6AE+6
ND 1/16ND 1/16
12:34:56 12:34:56
Jan 24,2015Jan 24,2015
00:00:00.0000:00:00.00
5.5.6 f t
100min100min
50min50min
282min282min
P 13000K
To p
Bottom
GY-HM200_170Sheet_EN.fm 1 ページ ２０１５年９月１１日 金曜日 午後６時１８分

B5A-1103-00
2
© 2015 JVC KENWOOD Corporation
[Adaptive Bit Rate] and [PCR Jitter] added to menu item (K)
The following items are added to [System] N [Network]/[Settings] N [Live
Streaming Set]
N [Streaming Server] N [Server1] / [Server2] / [Server3] /
[Server4].
●Adaptive Bit Rate:
If “On” is selected, the bit rate setting value of live streaming is set to
maximum limit, and the bit rate is changed automatically according
to changes in the network bandwidth. [Setting Values: On, ROff]
Memo :
●Adaptive bit rate setting is possible only when [Type] is set to “ZIXI” and
[Latency] is set to either “Medium” or “Low”.
* The bit rate is displayed on the status screen only when “On” is set.
●PCR Jitter:
Setting to “Low” reduces to PCR jitter of live streaming.
[Setting Values: RNormal, Low]
Memo :
●This item is selectable only when [Type] is set to “MPEG2-TS/UDP”.
[APN] added to menu item (K)
[APN] is added to [System]N[Network] / [Settings]N[Connection
Setup].
* APN: Access Point Name
* This item is gray out and cannot be selected if APN cannot be set for
the adapter attached.
Caution :
●The APN setting is written into the cellular adapter, not this camera
recorder. Setting a wrong APN may result in communication failure or
expensive bills from the telecommunications company. Set the APN
correctly.
FTP resume feature added (K)
When FTP transfer starts and there is a file of the same name on the
server with a file size smaller than the file to be transferred, the file on
the server will be regarded as an interrupted file during a FTP transfer.
A confirmation screen to resume transfer (append writing) appears.
If “Resume” is selected, FTP transfer is carried out such that it appends
from the position where it was interrupted. When FTP transfer ends
normally, “Successfully Completed.” appears on the screen.
Memo :
●FTP server equipped with resume function is required.
●If [System]N[Network] / [Settings]N[Clip Server]N[Clip-FTP1/2/3/4]N
[Protocol] is set to “SFTP”, the “Resume” function is disabled.
●If “HTTP” is selected in the [Select FTP Proxy] screen of the network
connection setting, the resume function is disabled.
Setting value “ZIXI” added to menu item [Protocol] (K)
“ZIXI” is added to [System]N[Network] / [Settings]N[Clip Server]N
[Clip-FTP1/2/3/4]N[Protocol].
If “ZIXI” is selected, [Username] in [System] N [Network] / [Settings] N
[Clip Server]
N [Clip-FTP1/2/3/4] changes to [Stream ID].
[Setting Values:
R FTP, SFTP, FTPS, FTPES, ZIXI]
Memo :
●To use the “ZIXI” setting, a dedicated server is needed separately.
●If “ZIXI” is set, the “Resume” function is enabled.
Items added to thumbnail screen
The following items are added to the metadata display on the detailed
screen of the thumbnail screen.
●Clip Size
●Gamma
Clip Continuous added to recording mode for AVCHD
“Clip Continuous” is added to the setting value for “AVCHD” format in
[System]N[Record Set]N[Rec Mode].
Clip Continuous Rec can also be operated in “AVCHD” mode.
Setting value “Side Cut” added to menu item [SD Aspect]
“Side Cut” is added to the setting value for [A/V Set]N[Video Set]N
[SD Aspect].
●Letter:
Displays as a wide image with the top and bottom blackened.
●Squeeze:
Displays image that is squeezed horizontally.
●Side Cut:
Displays wide screen with the left and right sides cut off.
[Setting Values: RSqueeze, Letter, Side Cut]
Memo :
●When “SD” is selected in [System]N[Record Set]N[Record Format]N
[System], “Squeeze” and “Letter” can be selected.
2.5x display mode added to Expanded Focus function in 4K mode
An approximately 2.5x display mode is added to the Expanded Focus
function when “4K” is selected in [System]N[Record Set]N[Record
Format]N[System]. You can use the Set button (R) to switch between
the conventional dot by dot equivalent (approximately 5x) display and
the 2.5x display.
Memo :
●Upon power on, the display of the initial Expanded Focus is dot by dot
equivalent (approximately 5x).
[Camera Data] added to menu item
[Camera Data] is added to [LCD / VF]N[Display Settings].
●Always:
The Iris F-number, Gain, Shutter and White Balance values are
always displayed. The [A] icon appears on the left of the value when
in the Auto mode.
●Manual Only:
The Iris F-number, Gain, Shutter and White Balance values are
displayed only in Manual mode.
[Setting Values: Always, RManual Only]
Setting for operating Iris/Shutter/AE Level using iris dial added
Setting value “Iris/Shutter/AE Level” are added to [Camera Function] N
[Iris Dial].
If “Iris/Shutter/AE Level” is selected, the iris dial that is normally used to
operate the iris will operate the shutter when the [SHUTTER] button is
pressed and will operate the AE level when the [AE LEVEL] button is
pressed. After which, the iris dial resumes its iris operation.
[Setting Values: RIris, Shutter, AE Level, Iris/Shutter/AE Level]
[HDMI TC] added to menu item
[HDMI TC] is added to [A/V Set]N[Video Set].
For setting whether to superimpose the time code to the HDMI output
terminal.
[Setting Values: ROff, On]
Memo :
●When [A/V Set]N[Video Set]N[HDMI/SDI Out] is set to “SDI” or “Off”,
[HDMI TC] is fixed at “Off” and selection is disabled. (K)
●When [A/V Set]N[Video Set]N[HDMI Out] is set to “Off”, [HDMI TC] is
fixed at “Off” and selection is disabled. (M)
● Set to “Off” when connecting to a device that does not support HDMI TC.
Setting value changed in [Resolution] under [HDMI/SDI Out]
(K) and [HDMI Out] (M)
The video output is changed to native frame rate and setting values are
added. For selecting the resolution of video output from the [HDMI]
terminal or [SDI OUT] terminal according to the monitor to be connected.
[Setting Values: 576i, 576p, 480i, 480p, 720p, 1080i, 1080p, 1080/30p,
1080/25p, 1080/24p, 2160/24p, 2160/25p, 2160/30p]
Other notes
● The “MPEG LA MPEG-2 Patent” described in the “INSTRUCTIONS”
of this book is not applicable to this product.
Manufacturer
3-12, Moriya-cyo, Kanagawa-ku, Yokohama-shi,
Kanagawa221-0022, Japan
GY-HM200_170Sheet_EN.fm 2 ページ ２０１５年９月１１日 金曜日 午後６時１８分