JVC KD-R881BT User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
ไทย
B5A-1354-00 [M]
KD-R881BT / KD-R781BT
CD RECEIVER
INSTRUCTION MANUAL
เครื่องเลน CD
คู่มือการใช้งาน
JS_JVC_KD_R881BT_M_C_3.indd 1JS_JVC_KD_R881BT_M_C_3.indd 1 8/8/2016 10:25:00 PM8/8/2016 10:25:00 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2ENGLISH
CONTENTS BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe
Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe driving.
•
Do not ingest the battery, Chemical Burn Hazard
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
•
Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
•
Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RM-RK52):
•
Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
1 Cancel the demonstration
2 Set the clock and date
3 Set the basic settings
RADIO 5
CD/USB/iPod/ANDROID 7
Pandora®
(Applicable for Australia or
New Zealand models only) 9
BLUETOOTH® 10
AUX 17
AUDIO SETTINGS 17
DISPLAY SETTINGS 23
REFERENCES 24
Maintenance
More information
TROUBLESHOOTING 26
SPECIFICATIONS 28
INSTALLATION /
CONNECTION 29
How to read this manual
• Operations are explained mainly using buttons on the faceplate of KD-R881BT .
• English indications are used for the purpose of explanation. You can select the display language from the menu. ( 5)
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page.
JS_JVC_KD_R881BT_M_EN_3.indd 2JS_JVC_KD_R881BT_M_EN_3.indd 2 8/8/2016 10:24:21 PM8/8/2016 10:24:21 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power. ( Not available )
Adjust the volume Press .
• Press and hold to continuously increase the
volume to 15.
Press or .
• Press and hold to continuously increase
the volume to 15.
Press to mute the sound or pause playback.
• Press again to cancel.
Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press repeatedly.
• Press , then press within 2 seconds.
Press SOURCE repeatedly.
Change the display information Press repeatedly.
( 25)
( Not available )
Faceplate
Loading slot
Detach button
Display window
Attach How to resetDetach
Remote control (RM-RK52)
How to replace the battery
Pull out the
insulation sheet
when using for the
first time.
Remote sensor (Do not expose to bright sunlight.)
JS_JVC_KD_R881BT_M_EN_6.indd 3JS_JVC_KD_R881BT_M_EN_6.indd 3 1/9/2016 10:27:09 AM1/9/2016 10:27:09 AM

ENGLISH
4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
When you turn on the power (or [FACTORY RESET] is set to [YES] ), the display
shows: “CANCEL DEMO” “PRESS ENTER”
1 Press .
[YES] is selected for the initial setup.
2 Press again.
“DEMO OFF” appears.
Set the clock and date
1 Press and hold .
2 Press to select [CLOCK] , then press .
To adjust the clock
3 Press to select [CLOCK ADJUST] , then press .
4 Press to make the settings, then press .
Hour Minute
5 Press to select [CLOCK FORMAT] , then press .
6 Press to select [12H] or [24H] , then press .
To set the date
7 Press to select [DATE SET] , then press .
8 Press to make the settings, then press .
Day Month Year
9 Press to exit.
To return to the previous setting item, press .
1
2
Set the basic settings
1 Press and hold .
2 Press to select an item (see the following table), then
press .
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default: XX
SYSTEM
KEY BEEP
(Not applicable when 3-way crossover is selected.)
ON :Activates the keypress tone.; OFF :Deactivates.
SOURCE SELECT
AM SRC
*
ON :Enables AM in source selection.; OFF :Disables. ( 5)
SW1 SRC
*
ON :Enables SW1 in source selection.; OFF :Disables. ( 5)
SW2 SRC
*
ON :Enables SW2 in source selection.; OFF :Disables. ( 5)
PANDORA SRC
* ON :Enables PANDORA in source selection.; OFF :Disables. ( 9)
BUILT-IN AUX
*
ON :Enables AUX in source selection.; OFF :Disables. ( 17)
F/W UPDATE
UPDATE SYSTEM
F/W UP xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
FACTORY RESET YES :Resets the settings to default (except the stored station).;
NO :Cancels.
*
Not displayed when the corresponding source is selected.
3
JS_JVC_KD_R881BT_M_EN_3.indd 4JS_JVC_KD_R881BT_M_EN_3.indd 4 8/8/2016 10:24:23 PM8/8/2016 10:24:23 PM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
CLOCK
TIME SYNC ON
:The clock time is automatically set using
the Clock Time (CT) data in FM Radio Data
System signal.;
OFF :Cancels.
CLOCK DISPLAY ON :The clock time is shown on the display even
when the unit is turned off.;
OFF :Cancels.
ENGLISH Select the display language for menu and music
information if applicable.
By default,
ENGLISH is selected.
ESPANOL
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
1 Press repeatedly to select FM, AM, SW1 or SW2.
2 Press (or press on the remote control) to search for a station
automatically.
(or)
Press and hold (or press and hold on the remote control) until “M”
flashes, then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM, 6 stations for AM/SW1/SW2.
Store a station
While listening to a station....
Press and hold one of the number buttons (1to 6).
(or)
1 Press and hold until “PRESETMODE” flashes.
2 Press to select a preset number, then press .
The preset number flashes and “MEMORY” appears.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press .
2 Press to select a preset number, then press .
JS_JVC_KD_R881BT_M_EN_3.indd 5JS_JVC_KD_R881BT_M_EN_3.indd 5 8/8/2016 10:24:23 PM8/8/2016 10:24:23 PM

ENGLISH
6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Other settings
1 Press and hold .
2 Press to select an item ( see the following table ) , then
press .
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
TUNER SETTING
RADIO TIMER
Turns on the radio at a specific time regardless of the current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the timer will be turned
on.
2 FM / AM/SW1/SW2 :Select a band.
3 01 to 18 (for FM)/ 01 to 06 (for AM/SW1/SW2):Select a preset station.
4 Set the activation day
*1
and time.
“
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AM SRC] / [SW1 SRC] / [SW2 SRC] in
[SOURCE SELECT] after Radio Timer for AM/SW1/SW2 is selected. ( 4)
SSM SSM 01–06
/ SSM 07–12 / SSM 13–18 : Automatically presets up to 18
stations for FM. “SSM” stops flashing when the first 6 stations are stored.
Select
SSM 07–12 / SSM 13–18 to store the following 12 stations.
LOCAL SEEK ON :Searches only AM/SW1/SW2 stations with good reception.;
OFF :Cancels.
• Settings made are applicable only to the selected source/station. Once
you change the source/station, you need to make the settings again.
RADIO
IF BAND AUTO :Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.);
WIDE :Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
MONO SET ON :Improves the FM reception, but the stereo effect will be lost.;
OFF :Cancels.
NEWS SET
*2
ON :The unit will temporarily switch to News Programme if available.;
OFF :Cancels.
REGIONAL
*2
ON : Switches to another station only in the specific region using the “AF”
control.;
OFF :Cancels.
AF SET
*2
ON : Automatically searches for another station broadcasting the same
program in the same Radio Data System network with better reception
when the current reception is poor.;
OFF : Cancels.
TI
*2
ON : Allows the unit to temporarily switch to Traffic Information if available
(“TI” lights up). ;
OFF :Cancels.
PTY SEARCH
*2
Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
*1
Selectable only when [ONCE] or [WEEKLY] is selected in step 1 .
*2
Only for FM source.
PTY code
NEWS , AFFAIRS , INFO , SPORT , EDUCATE , DRAMA , CULTURE , SCIENCE , VARIED , POP
M
(music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS , OTHER
M
(music), WEATHER , FINANCE , CHILDREN , SOCIAL , RELIGION , PHONE IN , TRAVEL ,
LEISURE , JAZZ , COUNTRY , NATION M (music), OLDIES , FOLK M (music), DOCUMENT
JS_JVC_KD_R881BT_M_EN_3.indd 6JS_JVC_KD_R881BT_M_EN_3.indd 6 8/8/2016 10:24:24 PM8/8/2016 10:24:24 PM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Selectable sources:
KD-R881BT : CD/USB/iPod USB/ANDROID
KD-R781BT : CD/USB/ANDROID
To On the faceplate On the remote control
Reverse/Fast-forward*3Press and hold . Press and hold .
Select a track/file Press .Press .
Select a folder*4Press . Press .
Repeat play*5Press repeatedly.
TRACK REPEAT / ALL REPEAT : Audio CD
TRACK REPEAT / FOLDER REPEAT / ALL REPEAT : MP3/WMA/AAC/WAV/FLAC file
ONE REPEAT / ALL REPEAT / REPEAT OFF : iPod or ANDROID
Random play*5Press repeatedly.
ALL RANDOM / RANDOM OFF : Audio CD
FOLDER RANDOM / ALL RANDOM / RANDOM OFF : MP3/WMA/AAC/WAV/FLAC file
SONG RANDOM / ALL RANDOM / RANDOM OFF : iPod or ANDROID
*1
Do not leave the cable inside the car when not using.
*2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting. For
more information, visit <http://www.jvc.net/cs/car/>.
*3
For ANDROID: Applicable only when [AUTO MODE] is selected. ( 8)
*4
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
*5
For iPod/ANDROID: Applicable only when [HEAD MODE] / [AUTO MODE] is selected. ( 8)
Start playback
The source changes automatically and
playback starts.
CD
Eject disc Label side
USB input terminal
USB 2.0 cable
*1
(commercially available)
Micro USB 2.0 cable
*1
(commercially available)
USB
ANDROID*2
Accessory of the
iPod/iPhone
*1
iPod/iPhone
JS_JVC_KD_R881BT_M_EN_3.indd 7JS_JVC_KD_R881BT_M_EN_3.indd 7 8/8/2016 10:24:24 PM8/8/2016 10:24:24 PM

ENGLISH
8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select control mode
While in iPodUSB source, press repeatedly.
HEAD MODE : Control iPod from this unit.
IPHONE MODE : Control iPod using the iPod itself. However, you can still
play/pause or file skip from this unit.
While in ANDROID source, press repeatedly.
AUTO MODE : Control Android device from this unit via JVC MUSIC PLAY
application installed in the Android device.
AUDIO MODE : Control Android device using the Android device itself via
other media player applications installed in the Android
device. However, you can still play/pause or file skip from
this unit.
Select music drive
While in USB source, press repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drives device.
Settings to use JVC Remote application (for KD-R881BT)
JVC Remote application is designed to control the JVC car receiver’s
operations from the iPhone/iPod (via USB input terminal).
Preparation:
Install the latest version of JVC Remote application on your device before
connecting. For more information, visit <http://www.jvc.net/cs/car/>.
You can make the settings in the same way as connection via Bluetooth.
( 16)
Select a file from a folder/list
For iPod/ANDROID, applicable only when [HEAD MODE] / [AUTO MODE] is
selected.
1 Press .
2 Press to select a folder/list, then press .
3 Press to select a file, then press .
Quick Search (applicable only for CD, USB and ANDROID source)
If you have many files, you can search through them quickly.
Press and hold to browse through the list quickly.
Alphabet search (applicable only for iPod USB and ANDROID source)
You can search for a file according to the first character.
For iPodUSB source
Press to select the desired character (A to Z, 0to9,
OTHERS).
• Select “OTHERS” if the first character is other than AtoZ, 0to9.
For ANDROID source
1 Press to enter character search.
2 Press to select the desired character.
^A^ : Upper case (A to Z)
_A_ : Lowor case (a to z)
-0- : Numbers (0 to 9)
-OTHERS- : Character other than A to Z, 0 to 9
3 Press to start searching.
• To return to the previous setting item, press .
• To cancel, press and hold .
CD/USB/iPod/ANDROID
JS_JVC_KD_R881BT_M_EN_5.indd 8JS_JVC_KD_R881BT_M_EN_5.indd 8 24/8/2016 3:02:55 PM24/8/2016 3:02:55 PM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora® (Applicable for Australia or New Zealand models only)
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/iPod touch), then create an account and log in to Pandora.
• Select
[ON] for [PANDORA SRC] in [SOURCE SELECT] . ( 4)
KD-R781BT
: You can only listen to Pandora via Bluetooth connection with
an Android device.
( 10, 16)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
3 Press repeatedly to select PANDORA.
Broadcast starts automatically.
To On the faceplate On the remote control
Playback/pause Press . Press .
Skip a track Press T. Press I.
Thumbs up or thumbs
down*2
Press . Press .
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Create and store a new station
1 Press .
2 Press to select [NEW STATION] , then press .
3 Press to select [FROM TRACK] or [FROM ARTIST] , then press
.
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (3, 4, 5or 6) to store.
To select a stored station: Press one of the number buttons (3, 4, 5or 6).
Search for a registered station
1 Press .
2 Press to select an item, then press .
[BY DATE] : According to the registered date
[A-Z] : By alphabetical order
3 Press to select the desired station, then press
.
To cancel, press and hold .
Bookmark current song information
Press and hold .
“BOOKMARKED” appears and the information is stored to your device.
• The bookmark is available on your Pandora account but not on this
unit.
USB input terminal
Accessory of the iPod/iPhone*
1
JS_JVC_KD_R881BT_M_EN_3.indd 9JS_JVC_KD_R881BT_M_EN_3.indd 9 8/8/2016 10:24:25 PM8/8/2016 10:24:25 PM

ENGLISH
10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pair and connect a Bluetooth device for the first time
1 Press to turn on the unit.
2 Search and select “KD-R8 BT”/“KD-R7 BT” on the Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number
(PIN) code immediately after searching.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “ENTER–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device are the same.
Press to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “ENTER–YES” “BACK–NO”
Press to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing.
( 14)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the
Bluetooth connection is established.
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if
you reset the unit. To delete the paired device,
14 , [DEVICE DELETE] .
• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at
any time.
However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and
switch between these five devices. (
15 )
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the
device to the unit manually.
• Refer to the instruction manual of the Bluetooth device for more information.
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the microphone
angle Secure using cord clamps
(not supplied) if necessary.
Microphone input jack
Microphone (supplied)
Rear panel
JS_JVC_KD_R881BT_M_EN_3.indd 10JS_JVC_KD_R881BT_M_EN_3.indd 10 8/8/2016 10:24:26 PM8/8/2016 10:24:26 PM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Auto Pairing
When you connect the following devices to
the USB input terminal, pairing request (via
Bluetooth) is automatically activated.
KD-R881BT : iPhone/iPod touch/Android device
KD-R781BT : Android device
Press to pair once you have
confirmed the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected device is
turned on.
–
[AUTO PAIRING] is set to [ON] . ( 14)
– JVC MUSIC PLAY application is installed on
the Android device
( 7) and [AUTO MODE] is
selected
( 8) .
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
• The symbolic button will blink in the color you have selected in
[RING COLOR] . ( 12)
• The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 12)
During a call:
• The symbolic button stop blinking and illuminate in the color you have selected in
[RING COLOR] .
( 12)
• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
The following operations may differ or not available depending on the connected phone.
To On the faceplate On the remote control
First incoming call...
Answer a call Press or . Press .
Reject a call Press and hold or . Press and hold .
End a call Press and hold or . Press and hold .
BLUETOOTH®
Symbolic button
JS_JVC_KD_R881BT_M_EN_3.indd 11JS_JVC_KD_R881BT_M_EN_3.indd 11 8/8/2016 10:24:27 PM8/8/2016 10:24:27 PM

ENGLISH
12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
To On the faceplate On the remote control
While talking on the first incoming call...
Answer another incoming
call and hold the current
call
Press or .
( Not available )
Reject another incoming
call
Press and hold or
.( Not available )
While having two active calls...
End current call and
activate held call
Press and hold or
.
Press and hold
.
Swap between the
current call and held call
Press .( Not available )
Adjust the phone volume*1
[00] to [35] (Default: [15] )
Press during
a call. ( Not available )
Switch between hands-free
and private talk modes*2
Press during a call. ( Not available )
*1
This adjustment will not affect the volume of the other sources.
*2
Operations may vary according to the connected Bluetooth device.
Improve the voice quality
While talking on the phone....
1 Press and hold .
2 Press to select an item ( see the following table ) , then press
.
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default: XX
MIC GAIN LEVEL –10 to LEVEL +10 ( LEVEL –04 ):The sensitivity of the
microphone increases as the number increased.
NR LEVEL LEVEL –05 to LEVEL +05 ( LEVEL 00 ):Adjust the noise
reduction level until the least noise is being heard during a
phone conversation.
ECHO CANCEL LEVEL –05 to LEVEL +05 ( LEVEL 00 ):Adjust the echo
cancellation delay time until the least echo is being heard
during a phone conversation.
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Press to select an item ( see the following table ) ,
then press .
3 Repeat step 2until the desired item is selected or
activated.
To return to the previous setting item, press .
Default:
XX
SETTINGS
AUTO ANSWER 01 SEC
to 30 SEC :The unit answers incoming call
automatically in the selected time (in seconds).;
OFF :Cancels.
RING COLOR COLOR  01 to COLOR  49 ( COLOR 08 ): Selects the illumination
color for symbolic button as notification when there is an
incoming call and during a call.;
OFF :Cancels.
BLUETOOTH®
JS_JVC_KD_R881BT_M_EN_3.indd 12JS_JVC_KD_R881BT_M_EN_3.indd 12 8/8/2016 10:32:47 PM8/8/2016 10:32:47 PM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by
voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode.
“(First device name)” appears.
• If two Bluetooth phones are connected, press again to switch to another
phone.
“(Second device name)” appears.
2 Press to select an item ( see the following table ) , then press .
3 Repeat step 2until the desired item is selected/activated or follow the instructions
stated on the selected item.
To return to the previous setting item, press .
RECENT CALL (Applicable only if the phone supports PBAP.)
1 Press to select a name or a phone number.
• “<” indicates call received, “>“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press to call.
PHONEBOOK (Applicable only if the phone supports PBAP.)
1 Press to select the desired letter (A to Z, 0to9, and OTHERS).
• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.
2 Press to select a name, then press .
3 Press to select a phone number, then press to call.
• The phonebook of the connected phone is automatically transferred to the unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
DIAL NUMBER 1 Press to select a number (0 to 9) or character ( , #, +).
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the phone number.
3 Press to call.
VOICE Speak the name of the contact you want to call or the voice command to control the phone
functions.
( Make a call using voice recognition)
BLUETOOTH®
Make a call using voice recognition
1 Press and hold to activate the connected
phone.
2 Speak the name of the contact you want to call or
the voice command to control the phone functions.
• Supported Voice Recognition features vary for each
phone. Refer to the instruction manual of the connected
phone for details.
• This unit also supports the intelligent personal assistant
function of iPhone.
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons
(1to 6).
1 Press to enter Bluetooth mode.
2 Press to select [RECENT CALL] , [PHONEBOOK] or
[DIAL NUMBER] , then press .
3 Press to select a contact or enter a phone
number.
If a contact is selected, press to show the
phone number.
4 Press and hold one of the number buttons (1to 6).
“MEMORY P(selected preset number)” appears when
the contact is stored.
To erase a contact from the preset memory, select
[DIAL NUMBER] in step 2and store a blank number.
Make a call from memory
1 Press to enter Bluetooth mode.
2 Press one of the number buttons (1to 6).
3 Press to call.
“NO PRESET” appears if there is no contact stored.
JS_JVC_KD_R881BT_M_EN_3.indd 13JS_JVC_KD_R881BT_M_EN_3.indd 13 8/8/2016 10:24:27 PM8/8/2016 10:24:27 PM

ENGLISH
14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Bluetooth mode settings
1 Press and hold .
2 Press to select an item ( see the following table ) , then press .
3 Repeat step 2until the desired item is selected/activated or follow the instructions
stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
BT MODE
PHONE SELECT
* Selects the phone or audio device to connect or disconnect.
“” appears in front of the device name when connected.
“” appears in front of the current playback audio device.
AUDIO SELECT *
DEVICE DELETE
1 Press to select a device to delete, then press .
2 Press to select [YES] or [NO] , then press .
PIN CODE EDIT
(0000)
Changes the PIN code (up to 6 digits).
1 Press to select a number.
2 Press to move the entry position.
Repeat steps
1 and 2 until you finish entering the PIN code.
3 Press to confirm.
RECONNECT ON :The unit automatically reconnect when the last connected Bluetooth device is within range.;
OFF :Cancels.
AUTO PAIRING ON :The unit automatically pair supported Bluetooth device (iPhone/iPod touch/Android device)
when it is connected through USB input terminal.Depending on the operating system of the
connected device, this function may not work. ;
OFF :Cancels.
INITIALIZE YES :Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.).;
NO :Cancels.
INFORMATION MY  BT  NAME : Displays the unit name (“KD-R8 BT”/“KD-R7 BT”).; MY  ADDRESS : Shows
address of this unit.
* You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device at any time.
BLUETOOTH®
Bluetooth compatibility check mode
You can check the connectivity of the supported
profile between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1 Press and hold .
“BLUETOOTH” “CHECK MODE” appears.
“SEARCH NOW USING PHONE” “PIN IS 0000”
scrolls on the display.
2 Search and select “KD-R8 BT”/“KD-R7 BT” on
the Bluetooth device within 3minutes.
3 Perform (A), (B) or (C) depending on what
appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey):
Ensure that the same passkey appears on the
unit and Bluetooth device, then operate the
Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on
the Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to
confirm pairing.
After pairing is successful, “PAIRING OK” “[Device
Name]” appears and Bluetooth compatibility check
starts.
If “CONNECT NOW USING PHONE” appears, operate
the Bluetooth device to allow phonebook access to
continue.
“TESTING” flashes on the display.
JS_JVC_KD_R881BT_M_EN_3.indd 14JS_JVC_KD_R881BT_M_EN_3.indd 14 8/8/2016 10:24:28 PM8/8/2016 10:24:28 PM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
The connectivity result flashes on the display.
“PAIRING OK” and/or “HANDS-FREE OK”*1and/
or “AUD.STREAM OK”*2and/or “PBAP OK”*3:
Compatible
*1
Compatible with Hands-Free Profile (HFP)
*2
Compatible with Advanced Audio Distribution Profile (A2DP)
*3
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to
indicate that pairing has been deleted, and the
unit exits check mode.
• To cancel, press and hold to turn off the
power, then turn on the power again.
BLUETOOTH®
BLUETOOTH — Audio
Audio player via Bluetooth
1 Press repeatedly to select BTAUDIO (or press SOURCE on the remote control).
• Pressing enters BT AUDIO directly.
2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback/pause Press .Press .
Select group or folder Press . Press .
Reverse skip/Forward skip Press .Press .
Reverse/Fast-forward Press and hold .Press and hold .
Repeat play Press repeatedly.
TRACK REPEAT , ALL REPEAT , REPEAT OFF
( Not available )
Random play Press repeatedly.
GROUP RANDOM , ALL RANDOM , RANDOM OFF
( Not available )
Select a file from a folder/
list
Refer to “Select a file from a folder/list”
on page 8. ( Not available )
Switch between
connected Bluetooth
audio devices
Press 5.*
( Not available )
*
Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.
Operations and display indications may differ according to their availability on the connected
device.
While in BT AUDIO source, you
can connect to five Bluetooth
audio devices and switch
between these five devices.
JS_JVC_KD_R881BT_M_EN_6.indd 15JS_JVC_KD_R881BT_M_EN_6.indd 15 1/9/2016 10:28:13 AM1/9/2016 10:28:13 AM

ENGLISH
16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
STATUS
Shows the status of the selected device.
IOS CONNECTED : You are able to use the application using the iPhone/iPod
connected via Bluetooth or USB input terminal.
IOS NOT CONNECTED : No IOS device is connected to use the application.
ANDROID CONNECTED : You are able to use the application using the Android
smartphone connected via Bluetooth.
ANDROID NOT CONNECTED : No Android device is connected to use the
application.
Listen to iPhone/iPod via Bluetooth (for KD-R881BT)
You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.
Press repeatedly to select iPodBT.
• You can operate the iPod/iPhone in the same way as iPod/iPhone via
USB input terminal.
( 7)
• If you plug in an iPhone/iPod to the USB input terminal while listening
to iPodBT source, the source automatically change to iPodUSB. Press
to select iPodBT if the device is still connected via Bluetooth.
Internet radio via Bluetooth
You can listen to Pandora on the following devices via Bluetooth on this
unit.
• Make sure the USB input terminal is not connected to any device.
KD-R881BT : iPhone/iPod touch/Android device
KD-R781BT : Android device
Listen to Pandora (Applicable for Australia or New Zealand models only)
Preparation:
Select
[ON] for [PANDORA SRC] in [SOURCE SELECT] . ( 4)
1 Open the Pandora application on your device.
2 Connect your device via Bluetooth connection. ( 10)
3 Press repeatedly to select PANDORA (for iPhone/iPod) or
PANDORA BT (for Android device).
The source switches and broadcast starts automatically.
• You can operate Pandora in the same way as Pandora via USB input
terminal.
( 9)
BLUETOOTH®
Settings to use JVC Remote application
JVC Remote application is designed to control the JVC car receiver’s
operations from the following devices.
KD-R881BT : iPhone/iPod (via Bluetooth or via USB input terminal) or
Android smartphone (via Bluetooth)
KD-R781BT : Android smartphone (via Bluetooth)
Preparation:
Install the latest version of JVC Remote application on your device before
connecting. For more information, visit <http://www.jvc.net/cs/car/>.
1 Press and hold .
2 Press to select an item ( see the following table ) , then
press .
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
REMOTE APP
SELECT
Select the device (IOS or ANDROID) to use the application.
IOS YES : Selects iPhone/iPod to use the application via Bluetooth or connected via
USB input terminal.;
NO :Cancels.
If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is
connected via USB input terminal) to activate the application.
• The connectivity of the application will be interrupted or disconnected if:
– You change from iPod BT source to any playback source connected via the
USB input terminal.
– You change from iPod USB source to iPod BT source.
ANDROID YES :Selects Android smartphone to use the application via Bluetooth.;
NO : Cancels.
ANDROID LIST *: Selects the Android smartphone to use from the list.
* Displayed only when [ANDROID] of [SELECT] is set to [YES] .
JS_JVC_KD_R881BT_M_EN_5.indd 16JS_JVC_KD_R881BT_M_EN_5.indd 16 24/8/2016 3:06:14 PM24/8/2016 3:06:14 PM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Use a portable audio player
1 Connect a portable audio player (commercially available).
2 Select [ON] for [BUILT-IN AUX] in [SOURCE SELECT] . ( 4)
3 Press repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
3.5mm stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
AUX AUDIO SETTINGS
1 Press and hold .
2 Press to select an item (see the following table), then
press .
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default:
XX
EQ SETTING
PRESET EQ
Select a preset equalizer suitable to the music genre.
• Select [USER] to use the settings made in [EASY EQ] or [PRO EQ] .
FLAT / DRVN 3 / DRVN 2 / DRVN 1 / HARD ROCK / HIP HOP / JAZZ / POP /
R&B / USER / CLASSICAL
Drive equalizer ( DRVN 3 / DRVN 2 / DRVN 1 ) boosts specific frequencies in
the audio signal to reduce the noise heard from outside the car or running
noise of the tyres.
EASY EQ Adjust your own sound settings.
• The settings are stored to [USER] .
• The settings made may affect the current settings of [PRO EQ] .
SUB.W SP
*1*2:
00 to +06 (Default: 03
SUB.W
*1*3:
–50 to +10 00
BASS
: LVL –09 to LVL +09 LVL 00
MID
: LVL –09 to LVL +09 LVL 00
TRE
: LVL –09 to LVL +09 LVL 00 )
*1, *2, *3:
( 18)
JS_JVC_KD_R881BT_M_EN_3.indd 17JS_JVC_KD_R881BT_M_EN_3.indd 17 8/8/2016 10:24:29 PM8/8/2016 10:24:29 PM

ENGLISH
18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
PRO EQ Adjust your own sound settings.
• The settings are stored to [USER] .
• The settings made may affect the current settings of [EASY EQ] .
62.5HZ
LEVEL –09 to LEVEL +09 (LEVEL 00) : Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
ON :Turns on the extended bass.; OFF :Cancels.
100HZ / 160HZ / 250HZ / 400HZ / 630HZ / 1KHZ / 1.6KHZ / 2.5KHZ / 4KHZ / 6.3KHZ / 10KHZ /
16KHZ
LEVEL –09 to LEVEL +09 (LEVEL 00) : Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
Q FACTOR 1.35 / 1.50 / 2.00 :Adjust the quality factor.
AUDIO CONTROL
BASS BOOST LEVEL +01
to LEVEL +05 : Selects your preferred bass boost level.;
OFF :Cancels.
LOUDNESS LEVEL 01 / LEVEL 02 :Boosts low or high frequencies to produce a well-
balanced sound at low volume.;
OFF :Cancels.
SUB.W LEVEL
*1
SPK-OUT
*2
(Not applicable when 3-way crossover is selected.)
SUB.W 00 to SUB.W +06 ( SUB.W +03 ):Adjusts the
output level of the subwoofer connected via speaker lead.
( 31)
PRE-OUT
*3
SUB.W –50 to SUB.W +10 ( SUB.W 00 ):Adjusts the
output level of the subwoofer connected to the lineout
terminals (SW or REAR/SW) through an external amplifier.
( 31)
SUBWOOFER
SET
*3
ON : Turns on the subwoofer output.; OFF :Cancels.
FADER (Not applicable when 3-way crossover is selected.)
POSITION R15 to POSITION F15 ( POSITION 00 ):Adjusts the front and
rear speaker output balance.
BALANCE
*4
POSITION L15 to POSITION R15 ( POSITION 00 ):Adjusts the left and
right speaker output balance.
VOLUME  ADJUST LEVEL –15 to LEVEL +06 ( LEVEL 00 ):Preset the initial volume level
of each source (compared to the FM volume level). Before adjustment,
select the source you want to adjust.
AMP  GAIN LOW  POWER :Limits the maximum volume level to 25. (Select if
the maximum power of each speaker is less than 50W to prevent
damaging the speakers.);
HIGH POWER :The maximum volume level
is 35.
SPK/PRE  OUT (Not applicable when 3-way crossover is selected.)
Depending on the speaker connection method, select the appropriate
setting to get the desired output.
( 19, Speaker output settings)
SPEAKER SIZE
Depending on the crossover type you have selected ( 19, [X ' OVER
TYPE]
), 2-way crossover or 3-way crossover setting items will be
shown.
( 20, Crossover settings)
By default, 2-way crossover type is selected.
X ' OVER
DTA SETTINGS
For settings, 22, Digital Time Alignment settings .
CAR SETTINGS
*1
Displayed only when [SUBWOOFER SET] is set to [ON] .
*2
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W] .
( 19)
*3
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or
[SUB.W/SUB.W] . ( 19)
*4
This adjustment will not affect the subwoofer output.
JS_JVC_KD_R881BT_M_EN_6.indd 18JS_JVC_KD_R881BT_M_EN_6.indd 18 2/9/2016 3:09:15 PM2/9/2016 3:09:15 PM

ENGLISH 19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
X ' OVER TYPE Caution : Adjust the volume before changing
the
[X ' OVER TYPE] to avoid the sudden
increase or decrease of the output level.
2-WAY (Displayed only when [3-WAY] is selected.)
YES :Selects two way crossover type.;
NO :Cancels.
3-WAY (Displayed only when [2-WAY] is selected.)
YES :Selects three way crossover type.;
NO :Cancels.
SOUND EFFECT
SPACE ENHANCE
(Not applicable for TUNER source.)
SMALL/MEDIUM/LARGE : Virtually enhances
the sound space.;
OFF :Cancels.
SND RESPONSE LEVEL1 / LEVEL2 / LEVEL3 : Virtually makes the
sound more realistic.;
OFF :Cancels.
SOUND LIFT LOW / MIDDLE / HIGH : Virtually adjust the
sound position heard from the speakers.;
OFF :Cancels.
VOL LINK EQ ON :Boosts the frequency to reduce the noise
heard from outside the car or running noise of
the tyres.;
OFF :Cancels.
K2 TECHNOLOGY (Not applicable for TUNER source and AUX
source.)
ON :Improve the sound quality of compressed
music.;
OFF :Cancels.
Speaker output settings [SPK/PRE OUT]
(Applicable only if [X ' OVER TYPE] is set to [2-WAY])
Select the output setting for the speakers [SPK/PRE OUT], based on the speaker connection
method.
Connection via lineout terminals
For connections through an external amplifier. ( 31)
KD-R881BT
:
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
FRONT REAR SW
REAR/REAR (default) Front speakers output Rear speakers output Subwoofer output
REAR/SUB.W ( Not available ) ( Not available ) ( Not available )
SUB.W/SUB.W Front speakers output L (left): Subwoofer output
R (right): (Mute)
Subwoofer output
KD-R781BT :
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
FRONT REAR/SW
REAR/REAR Front speakers output Rear speakers output
REAR/SUB.W (default) Front speakers output Subwoofer output
SUB.W/SUB.W Front speakers output Subwoofer output
JS_JVC_KD_R881BT_M_EN_3.indd 19JS_JVC_KD_R881BT_M_EN_3.indd 19 8/8/2016 10:24:29 PM8/8/2016 10:24:29 PM

ENGLISH
20
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
Crossover settings
Below are the available setting items for 2-way crossover and 3-way crossover.
Caution
Select a crossover type according to how the speakers are connected. ( 31)
If you select a wrong type:
• The speakers may damage.
• The output sound level may be extremely high or low.
SPEAKER SIZE
Selects according to the connected speaker size for optimum performance.
• The frequency and slope settings are automatically set for the crossover of the
selected speaker.
• When 2-way crossover is selected, if [NONE] is selected for [TWEETER] of [FRONT] ,
[REAR] and [SUBWOOFER] for [SPEAKER SIZE] , the [X ‘ OVER] setting of the selected
speaker is not available.
• When 3-way crossover is selected, if [NONE] is selected for [WOOFER] of [SPEAKER SIZE] ,
the
[X ‘ OVER] setting of [WOOFER] is not available.
X ‘ OVER
(crossover)
• [FRQ] / [F-HPF FRQ] / [R-HPF FRQ] / [SW LPF FRQ] / [HPF FRQ] / [LPF FRQ] : Adjusts the crossover
frequency for the selected speakers (high pass filter or low pass filter).
If
[THROUGH] is selected, all signals are sent to the selected speakers.
• [SLOPE] / [F-HPF SLOPE] / [R-HPF SLOPE] / [SW LPF SLOPE] / [HPF SLOPE] / [LPF SLOPE]: Adjusts the
crossover slope.
Selectable only if a setting other than
[THROUGH] is selected for the crossover
frequency.
• [SW LPF PHASE] / [PHASE]: Selects the phase of the speaker output to be in line with
the other speaker output.
• [GAIN LEFT] / [GAIN RIGHT] / [F-HPF GAIN] / [R-HPF GAIN] / [SW LPF GAIN] / [GAIN] : Adjusts the
output volume of the selected speaker.
Connection via speaker leads
For connections without using an external amplifier. However,
with this settings you can also enjoy the subwoofer output.
( 31)
Setting on
[SPK/PRE OUT]
Audio signal through rear speaker lead
L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output
REAR/SUB.W Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output (Mute)
If [SUB.W/SUB.W] is selected:
–
[120HZ] is selected in [SUBWOOFER LPF] and [THROUGH] is not
available.
–
[POSITION R02] is selected in [FADER] and selectable range is
[POSITION R15] to [POSITION 00] .
JS_JVC_KD_R881BT_M_EN_4.indd 20JS_JVC_KD_R881BT_M_EN_4.indd 20 18/8/2016 9:53:04 AM18/8/2016 9:53:04 AM