JVC KD-T905BTS User manual
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
FRANÇAIS
ESPAÑOL
B5A-2621-10 [K]
KD-T905BTS / KD-T900BTS / KD-T805BTS / KD-TD90BTS/
KD-T700BT / KD-TD70BT / KD-SR85BT
CD RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR CD
MANUEL D’INSTRUCTIONS
RECEPTOR CON CD
MANUAL DE INSTRUCCIONES
For customer Use:
Enter below the Model No. and Serial No. which are
located on the top or bottom of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
JS_JVC_KD_T905BTS_K_C.indd 1JS_JVC_KD_T905BTS_K_C.indd 1 8/24/2018 3:46:04 PM8/24/2018 3:46:04 PM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
i
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of labels on, or inside the product
relating to laser product safety.
JVC KENWOOD Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR
SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment may cause harmful interference to
radio communications, if it is not installed and used in accordance with the instructions. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special
handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida
útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de
residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser
desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final
de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento
adecuado a estos productos y a sus subproductos residuales correspondientes.
Póngase en contacto con su administración local para obtener información sobre el
punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación
de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos
perjudiciales en la salud y el medio ambiente.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou
entidade autorizada para que a mesma seja devolvida ao fabricante ou importador.
A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao
mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
Supplier's Declaration of Conformity
Trade Name: JVC
Products: CD RECEIVER
Model Name: KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS/KD-T700BT/
KD-TD70BT/KD-SR85BT
Responsible Party: JVCKENWOOD USA CORPORATION
2201 East Dominguez Street, Long Beach, CA 90810, U.S.A.
PHONE: 310 639-9000
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
JS_JVC_KD_T905BTS_K_C.indd iJS_JVC_KD_T905BTS_K_C.indd i 5/14/2018 11:55:24 AM5/14/2018 11:55:24 AM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ii
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to
comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be
installed and operated keeping the radiator at least 20 cm or more away from person’s body.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices
d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet
une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale
autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une
distance de 20 cm ou plus entre le radiateur et le corps humain.
IC (Industry Canada) Notice
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
Para cumplimiento de la IFT:
“La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada”
Contains Bluetooth Module FCC ID: ZWY8811X
IC ID: 12033A-8811X
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
JS_JVC_KD_T905BTS_K_C.indd iiJS_JVC_KD_T905BTS_K_C.indd ii 5/14/2018 11:55:25 AM5/14/2018 11:55:25 AM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iii
SOFTWARE LICENSE AGREEMENT
The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is
copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions
which Users shall follow in order to use the Licensed Software.
The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.
This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the
Product in which the "Licensed Software" is embedded.
The Licensed Software may include the software which has been licensed to the Licensor directly or
indirectly from any third party. In such case, some third parties require the Users to follow their conditions
for use separately from this Software License Agreement. Such software shall not be subject to this
Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided
separately below.
Article 1 General Provision
The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case
referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.
(the country where the User bought the Product (hereinafter the "Country")
Article 2 License
1. The license granted under this Agreement shall be the right to use the Licensed Software in the
Product.
2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed
Software and any related documents, whether in whole or in part.
3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall
not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.
4. The User shall use the Licensed Software according to the directions described in the operation
manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright
Law or any other laws and regulations by applying whole or a part of the Licensed Software.
Article 3 Conditions for Grant of License
1. When the User transfers the Product, it may also transfer the license to use the Licensed Software
embedded in the Product (including any related materials, updates and upgrades) on condition that
no original, copies or related materials continue in the possession of the User, and that the User shall
cause the transferee to comply with this Software License Agreement.
2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code
analysis works in connection with the Licensed Software.
Article 4 Right pertaining to the Licensed Software
Any and all copyrights and other rights pertaining to the Licensed Software and related documents
shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or
sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be
entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any
related documents.
Article 5 Indemnification of Licensor
1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User
or any third party due to the exercise of the license granted to the User under this Agreement, unless
otherwise restricted by law.
2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with
certain objective of the Licensed Software.
Article 6 Liability to Third Party
If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any
other intellectual property right that was caused by the User's use of the Licensed Software, the User shall
settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any
inconvenience it may cause.
Article 7 Confidentiality
The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof
or any other information to be granted under this Agreement, as well as the conditions of this Agreement
as has not yet entered the public domain, and shall not disclose or divulge the same to any third party
without approval of the Licensor.
Article 8 Termination
In case the User falls under any of the events described in the following items, the Licensor may
immediately terminate this Agreement or claim that the User compensates for the damage incurred by the
Licensor due to such event:
(1) when the User violated any provision of this Agreement; or
(2) when a petition has been filed against the User for an attachment,
provisional attachment, provisional disposition or any other compulsory execution.
Article 9 Destruction of the Licensed Software
If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed
Software, any related documents and copies thereof within two (2) weeks from such date of termination.
JS_JVC_KD_T905BTS_K_C.indd iiiJS_JVC_KD_T905BTS_K_C.indd iii 5/14/2018 11:55:25 AM5/14/2018 11:55:25 AM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iv
Article 10 Protection of Copyright
1. The copyright and all the other intellectual property rights
relating to the Licensed Software shall belong to the Licensor
and the Original Rightholder, and in no event shall they be
under the ownership of the User.
2. The User shall, whenever it uses the Licensed Software,
comply with any laws relating to the copyright and other
intellectual property rights.
Article 11 Export Restriction
1. It is prohibited to export the Licensed Software and any
related documents outside the country of the User (including
transmission thereof outside the country of the User via
Internet of other communication tools).
2. The User shall understand that the Licensed Software shall be
subject to the export restrictions adopted by the country of
User and any other countries.
3. The User shall agree that the software will be subject to any
and all applicable international and domestic laws (including
the export control regulation of the country of User and
any other countries, and any restrictions concerning the
end-users, the use by end-users and importing countries to be
provided by the country of User and any other countries, and
any other governmental authorities).
Article 12 Miscellaneous
1. In the event any part of this Agreement is invalidated by
operation of law, the residual provisions shall continue in
force.
2. Matters not stipulated in this Agreement or any ambiguity or
question raised in the construction of this Agreement shall be
provided or settled upon good-faith consultation between the
Licensor and the User.
3. The Licensor and the User hereby agree that this Agreement
is governed by the laws of Japan, and any dispute arising
from, and relating to the rights and obligations under, this
Agreement shall be submitted to the exclusive jurisdiction of
the Tokyo District Court for its first instance.
Important Notice concerning the Software
-jansson
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"),
to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/
or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR
IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-cJSON
Copyright (c) 2009 Dave Gamble
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"),
to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/
or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR
IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
-CMP
The MIT License (MIT)
Copyright (c) 2014 Charles Gunyon
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"),
to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/
or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR
IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
JS_JVC_KD_T905BTS_K_C.indd ivJS_JVC_KD_T905BTS_K_C.indd iv 5/14/2018 11:55:25 AM5/14/2018 11:55:25 AM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2ENGLISH
BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warnings
and Cautions in this manual.
• Please keep the manual in a safe and accessible place for future reference.
WARNING
• Do not operate any function that takes your attention away from safe driving.
• Do not ingest the battery, Chemical Burn Hazard.
The remote control supplied with this product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected
(page 40). Turn off the unit when parking at a low ceiling area.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
CONTENTS
BEFORE USE 2
BASICS 3
GETTING STARTED 4
1 Cancel the demonstration
2 Set the clock and date
3 Set the basic settings
RADIO 5
CD/USB/iPod/ANDROID 7
Pandora® 9
iHeartRadio® 10
Spotify 11
SiriusXM® Radio 12
BLUETOOTH® 15
AUX 24
AUDIO SETTINGS 24
DISPLAY SETTINGS 30
REFERENCES 31
Maintenance
More information
TROUBLESHOOTING 35
INSTALLATION/
CONNECTION 38
SPECIFICATIONS 42
How to read this manual
• Operations are explained mainly using buttons on the faceplate of KD-T905BTS.
• English indications are used for the purpose of explanation. You can select the display language from the menu. (Page 5)
• [XX] indicates the selected items.
• (Page XX) indicates references are available on the stated page.
JS_JVC_KD_T905BTS_K_EN_08.indd 2JS_JVC_KD_T905BTS_K_EN_08.indd 2 6/4/2018 11:35:48 AM6/4/2018 11:35:48 AM
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate On the remote control
Turn on the power Press BSRC.
• Press and hold to turn off the power. ( Not available )
Adjust the volume Turn the volume knob. Press VOL + or VOL – .
• Press and hold VOL + to continuously increase the
volume to 15.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. The volume level returns to the previous level
before muting or pause.
Press dto mute the sound or pause playback.
• Press again to cancel. The volume level returns to the
previous level before muting or pause.
Select a source • Press BSRC repeatedly.
• Press BSRC, then turn the volume knob within 2 seconds.
Press SOURCE repeatedly.
Change the display
information
Press repeatedly. (Page 33, 34) ( Not available )
Remote control (RM-RK52)
(except for KD-SR85BT)
This unit can be remotely controlled with an optionally
purchased remote control.
Attach How to resetDetach
Faceplate
How to replace the battery
Remote sensor (Do not expose to bright sunlight.)
Pull out the
insulation sheet
when using for
the first time.
Reset the unit
within 5 seconds
after detaching the
faceplate.
KD-T700BT/
KD-TD70BT/
KD-SR85BT
Volume knob Loading slot
Detach button
Display window
KD-T905BTS:
USB cable from the rear of the unit
JS_JVC_KD_T905BTS_K_EN_08.indd 3JS_JVC_KD_T905BTS_K_EN_08.indd 3 6/4/2018 11:35:50 AM6/4/2018 11:35:50 AM
4ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
When you turn on the power for the first time (or
[FACTORY RESET]
is set to
[YES]
, see page 5), the display shows: “CANCEL DEMO” “PRESS”
“VOLUME KNOB”
1 Press the volume knob.
[YES]
is selected for the initial setup.
2 Press the volume knob again.
“DEMO OFF” appears.
Set the clock and date
1 Press and hold .
2 Turn the volume knob to select
[CLOCK]
, then press the knob.
To adjust the clock
3 Turn the volume knob to select
[CLOCKADJUST]
, then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Hour Minute
5 Turn the volume knob to select
[CLOCK FORMAT]
, then press the knob.
6 Turn the volume knob to select
[12H]
or
[24H]
, then press the knob.
To set the date
7 Turn the volume knob to select
[DATESET]
, then press the knob.
8 Turn the volume knob to make the settings, then press the knob.
Day Month Year
9 Press to exit.
1
2
To return to the previous setting item, press .
Set the basic settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[SYSTEM]
[KEY BEEP] (Not applicable when 3-way crossover is selected.)
[ON]: Activates the keypress tone. ; [OFF]: Deactivates.
[SOURCE SELECT]
[AM SRC]*[ON]: Enables AM in source selection. ; [OFF]: Disables. (Page 5)
[PANDORA SRC]*[ON]: Enables PANDORA FRONT/PANDORA REAR/PANDORA/
PANDORA BT in source selection. ; [OFF]: Disables. (Page 9)
[IHEART SRC]*[ON]: Enables IHEARTRADIO-F/IHEARTRADIO-R/IHEARTRADIO in source
selection. ; [OFF]: Disables. (Page 10)
[SPOTIFY SRC]*[ON]: Enables SPOTIFY FRONT/SPOTIFY REAR/SPOTIFY/SPOTIFY BT in
source selection. ; [OFF]: Disables. (Page 11)
[BUILT-IN AUX]*[ON]: Enables AUX in source selection. ; [OFF]: Disables. (Page 24)
* Not displayed when the corresponding source is selected.
3
JS_JVC_KD_T905BTS_K_EN_08.indd 4JS_JVC_KD_T905BTS_K_EN_08.indd 4 6/4/2018 11:35:52 AM6/4/2018 11:35:52 AM
ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
[F/W UPDATE]
[UPDATE SYSTEM]
[F/W UP
xxxx]
[YES]: Starts upgrading the firmware. ;
[NO]: Cancels (upgrading is not activated).
For details on how to update the firmware, visit
<http://www.jvc.net/cs/car/>.
[FACTORY
RESET]
[YES]: Resets the settings to default (except the
stored station). ; [NO]: Cancels.
[CLOCK]
[TIME SYNC] [ON]: The clock time is automatically set using
the Clock Time (CT) data in FM Radio Broadcast
Data System signal. ; [OFF]: Cancels.
[CLOCK
DISPLAY]
[ON]: The clock time is shown on the
display even when the unit is turned off. ;
[OFF]: Cancels.
[ENGLISH] Select the display language for menu and music
information if applicable.
By default, [ENGLISH] is selected.
[ESPANOL]
RADIO
• “ST” or “STEREO” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
1 Press BSRC repeatedly to select FM or AM.
2 Press S/ T(or press H/ Ion the remote control) to search for a station automatically.
(or)
Press and hold S/ T(or press and hold H/ Ion the remote control) until “M” flashes,
then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station...
Press and hold one of the number buttons (1 to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
“MEMORY” appears once the station is stored.
GETTING STARTED
JS_JVC_KD_T905BTS_K_EN_08.indd 5JS_JVC_KD_T905BTS_K_EN_08.indd 5 6/4/2018 11:35:53 AM6/4/2018 11:35:53 AM
6ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press .
2 Turn the volume knob to select a preset number, then press the knob.
Other settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[TUNER SETTING]
[RADIO TIMER] Turns on the radio at a specific time regardless of the current source.
1
[ONCE]/[DAILY]/[WEEKLY]/[OFF]: Select how often the timer will be
turned on.
2
[FM]/[AM]/[SIRIUS XM]*1: Select the source.
3
[01] to [18] (for FM/SIRIUS XM)/[01] to [06] (for AM): Select the preset
station.
4
Set the activation day*2 and time.
“
” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AM SRC] in [SOURCESELECT] after Radio Timer for
AM is selected. (Page 4)
RADIO
[SSM] [SSM01–06]/[SSM07–12]/[SSM13–18]: Automatically presets up to
18 stations for FM. “SSM” stops flashing when the first 6 stations are stored.
Select [SSM07–12]/[SSM13–18] to store the following 12 stations.
[IF BAND] [AUTO]: Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.) ;
[WIDE]: Subjects to interference noises from adjacent FM stations, but
sound quality will not be degraded and the stereo effect will remain.
[MONO SET] [ON]: Improves the FM reception, but the stereo effect will be lost. ;
[OFF]: Cancels.
[AREA] [N.AMERICA]: For North/Central/South America, AM/FM intervals:
10 kHz/200 kHz. ;
[S.AMERICA]: For some South American countries, AM/FM intervals:
10 kHz/50 kHz. ;
[EUROPE]: For any other areas, AM/FM intervals: 9 kHz/50 kHz.
[PTY SEARCH]*3 Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
*1 KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS: Selectable only when SiriusXM Vehicle
Tuner is connected. (Page 12)
*2 Selectable only when [ONCE] or [WEEKLY] is selected in step 1.
*3 Only for FM source.
PTY code
[NEWS], [INFORM] (information), [SPORTS], [TALK], [ROCK], [CLSROCK] (classic rock),
[ADLTHIT] (adult hits), [SOFTRCK] (softrock), [TOP40], [COUNTRY], [OLDIES], [SOFT],
[NOSTALGA] (nostalgia), [JAZZ], [CLASSICL] (classical), [R&B] (rhythm and blues), [SOFTR&B]
(soft rhythm and blues), [LANGUAGE], [RELMUSC] (religious music), [RELTALK] (religious
talk), [PERSNLTY] (personality), [PUBLIC], [COLLEGE], [HABLESP] (Spanish talk), [MUSCESP]
(Spanish music), [HIPHOP], [WEATHER]
JS_JVC_KD_T905BTS_K_EN_08.indd 6JS_JVC_KD_T905BTS_K_EN_08.indd 6 6/4/2018 11:35:54 AM6/4/2018 11:35:54 AM
ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD/USB/iPod/ANDROID
Selectable source:
• KD-T905BTS:
CD/USB FRONT/USB REAR/iPod FRONT/iPod REAR/ANDROID FRONT/ANDROID REAR
• KD-T900BTS/KD-T805BTS/KD-TD90BTS/KD-T700BT/KD-TD70BT/KD-SR85BT:
CD/USB/iPod USB/ANDROID
To On the faceplate On the remote control
Reverse/Fast-forward*3 Press and hold S/ T. Press and hold H/ I.
Select a track/file Press S/ T. Press H/ I.
Select a folder*4 Press 2J/ 1K. Press J/ K.
Repeat play*3*5 Press 4repeatedly.
[TRACK REPEAT]
/
[ALL REPEAT]
: Audio CD
[TRACK REPEAT]
/
[FOLDER REPEAT]
/
[ALL REPEAT]
: MP3/WMA/AAC/WAV/
FLAC file
[ONE REPEAT]
/
[ALL REPEAT]
/
[REPEAT OFF]
: iPod
Random play*3*5 Press 3repeatedly.
[ALL RANDOM]
/
[RANDOM OFF]
: Audio CD
[FOLDERRANDOM]
/
[ALL RANDOM]
/
[RANDOM OFF]
: MP3/WMA/AAC/WAV/
FLAC file
[SONG RANDOM]
/
[ALL RANDOM]
/
[RANDOM OFF]
: iPod
*1 Do not leave the cable inside the car when not using.
*2 You can control Android device using the Android device itself via other media player application installed in the Android
device.
*3 Not applicable for ANDROID.
*4 For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.
*5 For iPod: Applicable only when [HEAD MODE] is selected. (Page 8)
Start playback
The source changes automatically and playback starts.
CD
Eject disc Label side
USB input terminal
USB 2.0 cable*1
(commercially available)
USB cable*1
(commercially available)
Accessory of the iPod/
iPhone*1
USB
iPod/iPhone
ANDROID*2
KD-T905BTS:
You can also connect to
the USB cable from the
rear of the unit.
JS_JVC_KD_T905BTS_K_EN_08.indd 7JS_JVC_KD_T905BTS_K_EN_08.indd 7 6/4/2018 11:35:54 AM6/4/2018 11:35:54 AM
8ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Select music drive
While in USBFRONT/USBREAR/USB source, press 5MODE repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drive device.
Settings to use JVC Remote application
JVC Remote application is designed to control the JVC car receiver’s
operations from the iPhone/iPod (via USB input terminal).
Preparation:
Install the latest version of JVC Remote application on your device before
connecting. For more information, visit <http://www.jvc.net/cs/car/>.
You can make the settings in the same way as connection via Bluetooth.
(Page 22)
Select control mode
While in iPodFRONT/iPodREAR/iPodUSB source (or iPodBT source),
press 5MODE repeatedly.
[HEAD MODE]
: Control iPod from this unit.
[IPHONE MODE]
: Control iPod using the iPod itself. However, you can still
perform play/pause, file skip, fast-forward or fast-reverse from
this unit.
Select a file from a folder/list
For iPod, applicable only when
[HEAD MODE]
is selected.
1 Press .
2 Turn the volume knob to select a folder/list, then press the knob.
3 Turn the volume knob to select a file, then press the knob.
Quick search
(applicable only for CD, USBFRONT, USBREAR and USB source)
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
Alphabet search
(applicable only for iPodFRONT, iPodREAR , iPodUSB source
or iPodBT source)
You can search for a file according to the first character.
Press 2J/ 1Kor turn the volume knob quickly to select the desired
character (A to Z, 0to9, OTHERS).
• Select “OTHERS” if the first character is other than A to Z, 0 to 9.
• To return to the previous setting item, press .
• To cancel, press and hold .
CD/USB/iPod/ANDROID
JS_JVC_KD_T905BTS_K_EN_08.indd 8JS_JVC_KD_T905BTS_K_EN_08.indd 8 6/4/2018 11:35:55 AM6/4/2018 11:35:55 AM
ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora®
Preparation:
Install the latest version of the Pandora application on your device (iPhone/
iPod touch), then create an account and log in to Pandora.
• Select
[ON]
for
[PANDORASRC]
in
[SOURCESELECT]
. (Page 4)
Start listening
1 Start up the Pandora application on your device.
2 Connect your device to the USB input terminal.
3 Press BSRC repeatedly to select PANDORA FRONT/PANDORA REAR/
PANDORA.
Broadcast starts automatically.
To On the faceplate On the remote control
Play back/pause Press the volume knob. Press d.
Skip a track Press T. Press I.
Select thumbs up
or thumbs down*2
Press 2J/ 1K. Press J/ K.
*1 Do not leave the cable inside the car when not used.
*2 If thumbs down is selected, the current track is skipped.
Create and store a new station
1 Press .
2 Turn the volume knob to select
[NEW STATION]
, then press the knob.
3 Turn the volume knob to select
[FROM ARTIST]
or
[FROM TRACK]
, then
press the knob.
A new station is created based on the current song or artist.
4 Press and hold one of the number buttons (3, 4, 5 or 6) to store.
To select a stored station: Press one of the number buttons (3, 4, 5 or 6).
Search for a registered station
1 Press .
2 Turn the volume knob to select an item, then press the knob.
[BYDATE]
: According to the registered date
[A-Z]
: By alphabetical order
3 Turn the volume knob to select the desired station, then press the
knob.
To cancel, press and hold .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
• The bookmark is available on your Pandora account but not on this unit.
USB input terminal
and/or
Accessory of the iPod/iPhone*1
KD-T905BTS: You can also connect to the
USB cable from the rear of the unit.
JS_JVC_KD_T905BTS_K_EN_08.indd 9JS_JVC_KD_T905BTS_K_EN_08.indd 9 6/4/2018 11:35:55 AM6/4/2018 11:35:55 AM
10 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iHeartRadio®
Preparation:
Install the latest version of iHeartAuto application on your device (iPhone/
iPod touch), then create an account and log in to iHeartRadio.
• Select
[ON]
for
[IHEART SRC]
in
[SOURCE SELECT]
. (Page 4)
Start listening
1 Start up the iHeartAuto application on your device.
2 Connect your device to the USB input terminal.
3 Press BSRC repeatedly to select IHEARTRADIO-F/IHEARTRADIO-R/
IHEARTRADIO.
Broadcast starts automatically
* Do not leave the cable inside the car when not used.
To On the faceplate On the remote control
Play back/pause Press the volume knob. Press d.
Skip a track for custom
station
Press T. Press I.
Select thumbs up or
thumbs down
Press 2J/ 1K. Press J/ K.
Create a new/custom
station
Press and hold the volume
knob. ( Not available )
Scan for live station 1 Press 3 to start
scanning.
2 Press 3 again to listen
to the station.
( Not available )
Search and store a station
1 Press .
2 Turn the volume knob to select a category, then press the knob.
3 Turn the volume knob to select the desired station, then press the
knob.
When a city list appears, you can search cities in alphabetical order by
turning the volume knob quickly.
To cancel, press and hold .
To store a station: Press and hold one of the number buttons (4, 5 or 6).
To select a stored station: Press one of the number buttons (4, 5 or 6).
USB input terminal
Accessory of the iPod/iPhone*
KD-T905BTS: You can also connect to the
USB cable from the rear of the unit.
and/or
JS_JVC_KD_T905BTS_K_EN_08.indd 10JS_JVC_KD_T905BTS_K_EN_08.indd 10 6/4/2018 11:35:55 AM6/4/2018 11:35:55 AM
ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Spotify
Preparation:
Install the latest version of the Spotify application on your device (iPhone/
iPod touch), then create an account and log in to Spotify.
• Select
[ON]
for
[SPOTIFY SRC]
in
[SOURCE SELECT]
. (Page 4)
Start listening
1 Start up the Spotify application on your device.
2 Connect your device to the USB input terminal.
3 Press BSRC repeatedly to select SPOTIFYFRONT/SPOTIFYREAR/
SPOTIFY.
Broadcast starts automatically
* Do not leave the cable inside the car when not used.
To On the faceplate On the remote control
Play back/pause Press the volume knob. Press d.
Skip a track Press S*1 / T. Press H*1 / I.
Select thumbs up or
thumbs down*2
Press 2J/ 1K. Press J/ K.
Start radio Press and hold 5. ( Not available )
To On the faceplate On the remote control
Repeat play*3 Press 4repeatedly.
[ALLREPEAT], [ONE REPEAT]*1,
[REPEATOFF]
( Not available )
Random play*3 Press 3repeatedly*1.
[ALLRANDOM], [RANDOMOFF]
( Not available )
*1 Available for premium account users only.
*2 This feature is available for tracks in Radio only. If thumbs down is selected, the current track is
skipped.
*3 Available for tracks in Playlists only.
Save favorite song information
While listening to the Radio on Spotify...
Press and hold the volume knob.
“SAVED” appears and the information is stored to “Your Music” or “Your
Library” on your Spotify account.
To unsave, repeat the same procedure.
“REMOVED” appears and the information is removed from “Your Music” or
“Your Library” on your Spotify account.
Search for a song or station
1 Press .
2 Turn the volume knob to select a list type, then press the knob.
The list types displayed differ depending on the information sent from
Spotify.
3 Turn the volume knob to select the desired song or station, then press
the knob.
You can browse through the list quickly by turning the volume knob
quickly.
To cancel, press and hold .
USB input terminal
Accessory of the iPod/iPhone*
KD-T905BTS: You can also connect to the
USB cable from the rear of the unit.
and/or
JS_JVC_KD_T905BTS_K_EN_08.indd 11JS_JVC_KD_T905BTS_K_EN_08.indd 11 6/4/2018 11:35:56 AM6/4/2018 11:35:56 AM
12 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SiriusXM® Radio
(for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS)
Start listening
1 Press BSRC repeatedly to select SIRIUSXM.
2 Press .
“ ” lights up.
3 Turn the volume knob to select a CATEGORY, then press the knob.
4 Turn the volume knob to select a category from the list, then press the knob.
If “ALL CHANNELS” is selected, all the available channels will be shown.
5 Turn the volume knob to select a channel, then press the knob.
(or)
Press S/ Tto search for a channel manually.
• Pressing and holding S/ Tchanges the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears. Enter
the pass code to receive the channel. (Page 14)
Settings in memory
You can store up to 18 channels.
Store a channel
While listening to a channel...
Press and hold one of the number buttons (1 to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Select a stored channel
Press one of the number buttons (1to6) (or press J/ Kon the remote control).
(or)
1 Press .
2 Turn the volume knob to select PRESET, then press the knob.
3 Turn the volume knob to select a preset number, then press the knob.
Only SiriusXM® brings you more of what you love
to listen to, all in one place. Get over 140 channels,
including commercial-free music plus the best sports,
news, talk, comedy and entertainment. Welcome to the
world of satellite radio. A SiriusXM Vehicle Tuner and
Subscription are required. For more information, visit
<www.siriusxm.com>.
Preparation:
1 Connect the optional SiriusXM Vehicle Tuner
(commercially available).
2 Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and
can be found by tuning to Channel 0 as well as on
the label found on the SiriusXM Vehicle Tuner and its
packaging.
The Radio ID does not include the letters I, O, S or F.
3 Activate the subscription.
For users in the U.S.A.:
Online: Go to <www.siriusxm.com>
Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to <www.siriusxm.ca/subscribe-now>
Phone: Call 1-877-438-9677
4 Press BSRC repeatedly to select SIRIUSXM to start
updating.
Antenna
Expansion port on
the rear panel
SiriusXM Vehicle Tuner
JS_JVC_KD_T905BTS_K_EN_08.indd 12JS_JVC_KD_T905BTS_K_EN_08.indd 12 6/4/2018 11:35:56 AM6/4/2018 11:35:56 AM
ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Using SiriusXM tuner models later than SXV200: This unit can assign
a maximum of 18 SmartFavorites channels. Initially, all preset channels
are assigned as SmartFavorites.
• “
*” appears following the last character of the channel name for the
SmartFavorites channels.
When you select a SmartFavorite channel, you can rewind and replay up
to 30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if
[TUNE START]
is set to
[ON]
(page 14) for most music channels stored as a SmartFavorite.
To On the faceplate
Select a stored
SmartFavorite
channel
Press one of the number buttons (1 to 6).
1 Press .
2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset number,
then press the knob.
Cancel
SmartFavorites
channels
1 Press .
2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset number,
then press and hold the knob.
“
*” is removed from the last character.
Reassign
SmartFavorites
channels
Repeat steps 1 to 3 of “Cancel SmartFavorites
channels”.
“
*” appears following the last character.
SiriusXM Replay™
While listening to a channel...
1 Press the volume knob.
“ ” lights up and the unit memorizes this paused position.
2 Press the volume knob to start Replay.
Replay starts from the paused position in step 1.
During Replay...
To On the faceplate On the remote control
Play back/pause Press the volume knob. Press d.
Skip backward/forward Press S/ T. Press H/ I.
Rewind/Fast-forward Press and hold S/ T. Press and hold H/ I.
Go to Live and exit
Replay
Press and hold the volume
knob.
Press and hold d.
1 Press .
2 Turn the volume knob
to select LIVE, then press
the knob.
SmartFavorites and TuneStart™
User preset channels are initially assigned as the SmartFavorites channels.
SmartFavorite channel is available with SXV200 or later SiriusXM tuner models.
The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of
the SmartFavorites channels in the background.
Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels.
If you try to assign the 7th channel, an error beep tone will be heard. Initially,
preset channels 1 to 6 are assigned as SmartFavorites.
SiriusXM® Radio
(for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS)
JS_JVC_KD_T905BTS_K_EN_08.indd 13JS_JVC_KD_T905BTS_K_EN_08.indd 13 6/4/2018 11:35:57 AM6/4/2018 11:35:57 AM
14 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TuneScan™
You can get a short preview of the songs that you have missed on each of
your SmartFavorites music channels or a music channel currently tuned into.
1 Press .
2 Turn the volume knob to select TUNE SCAN, then press the knob.
Scanning start for the first 6 seconds of the recorded music contents.
• To listen to the current song, press the volume knob to stop scanning. The
unit continues playing the current song.
• To select the previous/next song, press S/ T.
• To cancel scanning, press and hold the volume knob. Playback returns to
the channel before you entered TuneScan.
SiriusXM settings
1 Press and hold .
2 Turn the volume knob to select an item (see the following table), then
press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: [XX]
[SIRIUS XM]
[CHANNEL LOCK] To unlock settings:
1
Turn the volume knob to select a number.
2
Press
S
/
T
to move to the entry position.
3
Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4
Press the volume knob to confirm.
[CODESET]
1
Press the volume knob to enter [NEW CODE].
2
Turn the volume knob to select a number.
3
Press
S
/
T
to move to the entry position.
4
Repeat steps 2 and 3 to enter a new 4-digit pass code.
5
Press the volume knob to confirm.
6
Repeat steps 2 to 5 to reconfirm the pass code.
• Make a note of the new pass code to enter channel lock settings for
next time.
[LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ;
[USER DEFINED]: Selects the individual channels the user wants to
lock. ; [OFF]: Cancels.
[CHANNEL EDIT]*1
1
Turn the volume knob to select a category, then press the knob.
2
Turn the volume knob to select a channel you want to lock, then
press the knob.
“L” appears in front of the channel number.
3
Press and hold to exit.
[CHANNEL CLEAR]*1 [YES]: Clears all the locked channels. ; [NO]: Cancels.
[TUNE START]*2 [ON]: All qualified music channels in the SmartFavorites will start
playback from the beginning of the song. ; [OFF]: Cancels.
[SIGNAL LEVEL] Shows the strength ([NO SIGNAL]/[WEAK]/[GOOD]/[STRONG]) of
the current received signal.
[BUFFER USAGE] Shows the memory usage ([0%] to [100%]) for Replay buffer.
[SXM RESET] [YES]: Resets all SiriusXM settings to default. ; [NO]: Cancels.
*1 Displayed only when [LOCK SETTING] is set to [USER DEFINED].
*2 Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later which supports
SmartFavorites.
SiriusXM® Radio
(for KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS)
JS_JVC_KD_T905BTS_K_EN_08.indd 14JS_JVC_KD_T905BTS_K_EN_08.indd 14 6/4/2018 11:35:57 AM6/4/2018 11:35:57 AM
ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pair and connect a Bluetooth device for the first time
1 Press BSRC to turn on the unit.
2 Search and select the name of your receiver (“KD-T9 BTS”/“KD-T8 BTS”/
“KD-T7 BT”/“KD-TD9 BTS”/“KD-TD7 BT”/“KD-SR8 BT”) on the Bluetooth device.
“BT PAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
3 Perform (A) or (B) depending on what appears on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “Device Name” “XXXXXX” “VOL–YES” “BACK–NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkeys appear on the unit and Bluetooth device are the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “Device Name” “VOL–YES” “BACK–NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing. (Page 19)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “” will light up when the Bluetooth
connection is established. For KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS, the battery and
signal strength of the connected Bluetooth device is shown (see
[FORMAT]
on page 30).
• This unit supports Secure Simple Pairing (SSP).
• Up to five devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you
reset the unit. To delete the paired device, see
[DEVICE DELETE]
on page 19.
• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any
time.
However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and switch
between these five devices. (Page 21)
BLUETOOTH®
Depending on the operating system and the
firmware version of your mobile phone, Bluetooth
features may not work with this unit.
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Adjust the microphone
angle Secure using cord clamps (not
supplied) if necessary.
Microphone input jack
Microphone (supplied)
Rear panel
JS_JVC_KD_T905BTS_K_EN_08.indd 15JS_JVC_KD_T905BTS_K_EN_08.indd 15 6/4/2018 11:35:58 AM6/4/2018 11:35:58 AM
16 ENGLISH
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
• Some Bluetooth devices may not automatically connect to the unit after
pairing. Connect the device to the unit manually.
• When the battery of the connected Bluetooth device runs low, “Device
Name” “LOW BATTERY” appears.
• Refer to the instruction manual of the Bluetooth device for more
information.
Auto Pairing
When you connect iPhone/iPod touch to the USB input terminal, pairing
request (via Bluetooth) is automatically activated.
Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected device is turned on.
–
[AUTO PAIRING]
is set to
[ON]
. (Page 19)
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
• KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS:
The buttons will blink in the color you have selected in
[RING COLOR]
.
(Page 18)
KD-T700BT/KD-TD70BT/KD-SR85BT:
The buttons will blink in the blinking pattern you have selected in
[RING ILLUMI]
. (Page 18)
• The unit answers the call automatically if
[AUTO ANSWER]
is set to a selected
time. (Page 18)
During a call:
• KD-T905BTS/KD-T900BTS/KD-T805BTS/KD-TD90BTS:
The buttons stop blinking and illuminate in the color you have selected in
[RING COLOR]
. (Page 18)
KD-T700BT/KD-TD70BT/KD-SR85BT:
The buttons stop blinking.
• If you turn off the unit or detach the faceplate, Bluetooth is disconnected.
BLUETOOTH®
JS_JVC_KD_T905BTS_K_EN_08.indd 16JS_JVC_KD_T905BTS_K_EN_08.indd 16 6/4/2018 11:35:59 AM6/4/2018 11:35:59 AM
Other manuals for KD-T905BTS
1
This manual suits for next models
6
Table of contents
Languages:
Other JVC Car Receiver manuals
