JVC KD-SV2800 Guide

1
53 mm
184 mm
KD-SV2800
Installation/Connection Manual
• This unit is designed to operate only on 12 V DC,
NEGATIVE ground electrical systems.
INSTALLATION
(IN-DASH MOUNTING)
•The following illustration shows a typical installation.
However, you should make adjustments
corresponding to your specific car. If you have any
questions or require information regarding
installation kits, consult your JVC car audio dealer
or a company supplying kits.
0403MNMMDWJEIN
EN
3
LVT1076-002A
[U]
1
Control panel
Trim plate
8
9
2
Handle
Fuse
Slot
Sleeve
Lock Plate
Control panel Trim plate
Mounting bolt
7
Sleeve
Dashboard
Rubber cushion
5
4
J
V
C
4
*
6
See “ELECTRICAL
CONNECTIONS.”
Parts list for installation and
connection
The following parts are provided with this unit.
After checking them, please set them correctly.
Handles
Hard case/Control panel Sleeve Trim plate
Power cord Lock nut (M5)
Washer (ø5)Rubber cushion
Mounting bolt
(M5 x 20 mm)
Remote controller Battery
• When using the optional stay
Sleeve
Washer Fire wall
Mounting bolt
Stay (option)
Lock nut
Screw (option)
Dashboard
• When installing the unit without using the sleeve
In a Toyota for example, first remove the car radio and install the unit in its place.
Note: When installing the unit on the mounting brackets, make sure to use the
8 mm-long screws. If longer screws are used, they could damage the unit.
Flat type screws
(M5 x 8 mm)*
Bracket*
* Not included with this unit.
Flat type screws
(M5 x 8 mm)*
Bracket*
Pocket
32
Removing the unit
• Before removing the unit, release
the rear section.
1 Remove the control panel.
2 Remove the trim plate.
3 Insert the 2 handles into the
slots, as shown. Then, while
gently pulling the handles away
from each other, slide out the
unit. (Be sure to keep the
handles after installing it.)
1
Control panel Trim plate
Handle
TROUBLESHOOTING
•The fuse blows.
* Are the red and black leads connected correctly?
•Power cannot be turned on.
* Is the yellow lead connected?
•No sound from the speakers.
* Is the speaker output lead short-circuited?
•Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded
in common?
•Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded
in common?
VIDEO CD
PBCENTER
CD EQ
FM/AM
VOL
DOWN
UP
ATT
OSD
AUDIO
123
456
78
0
9
RETURN
1 Before mounting: Press (control panel
release button) to detach the control panel if
already attached.
* When shipped from the factory, the control
panel is packed in the hard case.
2 Remove the trim plate.
3 Remove the sleeve after disengaging the sleeve
locks.
1Stand the unit.
Note: When you stand the unit, be careful
not to damage the fuse on the rear.
2Insert the 2 handles between the unit and the
sleeve, as illustrated, to disengage the sleeve
locks.
3Remove the sleeve.
Note: Be sure to keep the handles for future
use after installing the unit.
4 Install the sleeve into the dashboard.
* After the sleeve is correctly installed into the
dashboard, bend the appropriate tabs to hold
the sleeve firmly in place, as illustrated.
5 Fix the mounting bolt to the rear of the unit’s
body and place the rubber cushion over the end
of the bolt.
6 Do the required electrical connections.
7 Slide the unit into the sleeve until it is locked.
8 Attach the trim plate.
9 Attach the control panel.
Crimp Connector
Less than 30°
Install the unit at an angle of less than 30°
Instal_KD_SV2800[U].p65 03.4.2, 6:40 PM1

2
R
L
LINE OUT
REAR
L
R
L
R
L
R
FRONT
INPUT
R
L
R
L
R
L
INPUT
23
1
15
8
2
1
3
6
7
5
4
L
R+
-
+
-
+
-
+
-
L
R+
-
+
-
+
-
+
-
L
R+
-
+
-
+
-
+
-
A Typical Connections
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you
disconnect the battery’s negative terminal and make
all electrical connections before installing the unit. If
you are not sure how to install this unit correctly, have
it installed by a qualified technician.
Note:
This unit is designed to operate only on 12 V DC,
NEGATIVE ground electrical systems. If your vehicle
does not have this system, a voltage inverter is required,
which can be purchased at JVC car audio dealers.
•
Replace the fuse with one of the specified rating. If the
fuse blows frequently, consult your JVC car audio dealer.
•If noise is a problem...
This unit incorporates a noise filter in the power circuit.
However, with some vehicles, clicking or other
unwanted noise may occur. If this happens, connect
the unit’s rear ground terminal (see connection
diagram below) to the car’s chassis using shorter and
thicker cords, such as copper braiding or gauge wire.
If noise still persists, consult your JVC car audio dealer.
•Maximum input of the speakers should be more
than 50 W both at the rear and at the front, with an
impedance of 4 Ωto 8 Ω.
•Be sure to ground this unit to the car’s chassis.
•The heat sink becomes very hot after use. Be
careful not to touch it when removing this unit.
Heat sink
PRECAUTIONS on power supply and
speaker connections:
•DO NOT connect the speaker leads of the power
cord to the car battery; otherwise, the unit will
be seriously damaged.
•Connect the black lead (ground), yellow lead
(to car battery, constant 12 V), and red lead
(to an accessory terminal) correctly.
•BEFORE connecting the speaker leads of the power
cord to the speakers, check the speaker wiring in
your car.
–If the speaker wiring in your car is as
illustrated in Fig. 1 and Fig. 2 below,
DO NOT connect the unit using that original
speaker wiring. If you do, the unit will be seriously
damaged.
Redo the speaker wiring so that you can connect
the unit to the speakers as illustrated in Fig. 3.
–If the speaker wiring in your car is as
illustrated in Fig. 3, you can connect the unit
using the original speaker wiring in your car.
–If you are not sure of the speaker wiring of your
car, consult your car dealer.
Connecting the leads
Twist the core wires when connecting.
Solder the core wires to connect them securely.
CAUTION :
•To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
Video out
Signal cord
(not supplied
with this unit)
•Before connecting the monitor, make
sure that the unit is turned off.
KV-MR9000 Wide
color monitor
Monitor
connection unit
(supplied with
KV-MR9000)
•You can use either
INPUT 1 or 2 when
connecting this unit to
KV-MR9000.
Amplifier
*3: Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place not
coated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do
so may cause damage to this unit.
KD-SV2800
Fig. 3Fig. 2
Fig. 1
Before connecting: Check the wiring in
the vehicle carefully. Incorrect connection
may cause serious damage to this unit.
The leads of the power cord and those of
the connector from the car body may be
different in color.
1 Connect the colored leads of the
power cord to the car battery,
speakers and automatic power
antenna (if any) in the following
sequence.
1Black: ground
2Yellow: to car battery
(constant 12 V)
3Red: to an accessory terminal
4Blue with white stripe: to remote
lead of other equipment
(200 mA max.)
5Blue: to automatic antenna if any
(250 mA max.)
6Brown: to cellular phone system
(For details, refer to the instructions
of the cellular phone.)
7Light green: to parking brake,
metallic or chassis of the car
8Others: to speakers
2 Connect the antenna cord.
3 Finally connect the wiring harness to
the unit.
You can connect an monitor and other equipment to upgrade your car stereo system.
•Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.
•For amplifier only:
–Connect this unit’s line-out terminals to the amplifier’s line-in terminals.
–Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.
(Cover the terminals of these unused leads with insulating tape, as illustrated above.)
BConnections Adding Other Equipment
Monitor
Rear speakers
Remote lead
Signal cord (not supplied with this unit)
Y-connector (not
supplied with this unit)
Front speakers Blue with white stripe
JVC Amplifier
To other
equipment
JVC Amplifier
You can connect another power amplifier for front speakers.
Front
speakers
*3
*3
Connecting the parking brake cord
When installing the monitor in a location which
can be seen by the driver:
Connect the light green cord to the parking brake
system.
Parking brake lever
Foot brake
KD-SV2800
To metallic body or chassis of the car
Crimp connector
When installing the monitor in a location
which cannot be seen by the driver:
Connect to metallic body or chassis of the
car with the ground lead.
Parking brake switch
KD-SV2800
Parking brake connection
wire (light green)
Not included with this unit.
*2
*2
Connecting the crimp connector
White Gray
Gray with black stripe
Green
Purple
Green with black stripe
Left speaker (front)
Right speaker
(front)
Left speaker
(rear)
Line out
(see diagram )
To antenna
Antenna
terminal
*1: Before checking the operation
of this unit prior to installation,
this lead must be connected,
otherwise power cannot be
turned on.
Black
Blue with white stripe
Red
Yellow*1
To a live terminal in the fuse block connecting to the
car battery (bypassing the ignition switch)
To metallic body or chassis of the car
Fuse block
To an accessory terminal in the fuse block
Right speaker (rear)
White with black stripe
Purple with black stripe
Rear ground
terminal 15 A fuse
Not included with this unit. Ignition
switch
Blue
To remote lead of other
equipment (see diagram )
To automatic antenna if any
Brown
Light Green
To cellular phone system
To parking brake, metallic body or chassis of the
car (see below)
Video out (see diagram )
*
*
Wire connecting the battery and
the parking brake switch
Attach the parking brake wire
(light green) to this point.
Contact the metallic part of
the crimp to the wires inside.
Pinch the crimp firmly.
KD-SV2800
*
*2
Instal_KD_SV2800[U].p65 03.4.2, 6:40 PM2