JVC KD-SV3205 Guide

M
Battery
·∫µ‡µÕ√
L
Remote controller
√’‚¡µ§Õπ‚∑√≈
J
Rubber cushion
¬“ß°—π°√–·∑°
K
Handles
§—π∫—ߧ—∫
H
Lock nut (M5)
πÕµ≈ÁÕ§ (M5)
I
Mounting bolt (M5 ×20 mm)
≈—°µ‘¥ (M5 ×20 ¡‘≈≈‘‡¡µ√)
G
Washer (ø5)
ª√–‡°Áπ«ß·À«π (ø5)
F
Crimp connector
¢—È«µËÕ”À√—∫Àπ’∫
KD-SV3205
Installation/Connection Manual
°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß
GET0347-006A
[U/UH]
0106DTSMDTJEIN
EN, TH
1
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
• DO NOT install any unit in locations where;
– it may obstruct the steering wheel and gearshift lever operations.
– it may obstruct the operation of safety devices such as air bags.
– it may obstruct visibility.
• DO NOT operate the unit while driving.
• If you need to operate the unit while driving, be sure to look ahead carefully.
• The driver must not watch the monitor while driving.
If the parking brake is not engaged, “PARKING” flashes on the display, and no playback
picture will be shown on the monitor.
– This warning appears only when the parking brake wire is connected to the parking brake
system built in the car.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all
electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4to 8 ). If the maximum power is less than
50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 16 of the
INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.
Heat sink
·ºËπ√–∫“¬§«“¡√ÈÕπ
© 2006 Victor Company of Japan, Limited
Parts list for installation and connection
The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer
immediately.
√“¬°“√Ë«πª√–°Õ∫”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π
Ë«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À“°¡’‘Ëß„¥‰¡Ë§√∫ °√ÿ≥“ª√÷°…“µ—«·∑π®”ÀπË“¬‡§√◊ËÕ߇’¬ßµ‘¥√∂¬πµÏ JVC ‚¥¬∑—π∑’
§”‡µ◊Õπ
•Õ¬Ë“µ‘¥µ—È߇§√◊ËÕß„πµ”·ÀπËß∑’Ë;
ōÕ“®°’¥¢«“ß°“√∑”ß“π¢Õßæ«ß¡“≈—¬·≈–§—π‡°’¬√Ï
ōÕ“®°’¥¢«“ß°“√∑”ß“π¢ÕßÕÿª°√≥ϪÈÕß°—𧫓¡ª≈Õ¥¿—¬ ‡™Ëπ ·Õ√Ï·∫§
ōÕ“®°’¥¢«“ß“¬µ“
•Õ¬Ë“„™Èß“π¢≥–¢—∫¢’Ë
• ∂È“®”‡ªÁπµÈÕß„™È‡§√◊ËÕߢ≥–¢—∫¢’Ë ¢Õ„ÀÈ¥Ÿ∑“ߢȓßÀπÈ“„ÀÈ¥’
•ºŸÈ¢—∫µÈÕ߉¡Ë¡Õß∑’ˮաÕ𑇵Õ√Ï¢≥–¢—∫¢’Ë
À“°‰¡Ë‰¥È¢÷Èπ‡∫√°¡◊Õ ¢ÈÕ§«“¡ “PARKING” ®–°√–æ√‘∫∫π®Õ·¥ßº≈ ·≈–®–‰¡Ë¡’√Ÿª°“√‡≈Ëπ·¥ß∫π®Õ¿“æ
ō§”‡µ◊Õππ’È®–ª√“°Æ¢÷Èπ‡©æ“–‡¡◊ËÕµËÕ“¬‡∫√°°—∫√–∫∫‡∫√°„π√∂¬πµÏ‰«È‡∑Ë“π—Èπ
¢ÈÕ§«√√–«—ß”À√—∫°“√µËÕ·À≈Ë߮˓¬°”≈—ß·≈–≈”‚æß:
•Õ¬Ë“µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫·∫µ‡µÕ√’Ë√∂¬πµÏ ¡‘©–π—Èπ ™ÿ¥ª√–°Õ∫®–‰¥È√—∫§«“¡‡’¬À“¬¡“°
•°ËÕπ∑’Ë®–µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫≈”‚æß „Àȵ√«®Õ∫°“√‡¥‘𓬉ø≈”‚æß„π√∂¢Õߧÿ≥„Àȇ√’¬∫√ÈÕ¬‡’¬°ËÕπ
D
Trim plate
·ºËπ‚≈À–¢Õ∫·µËß
E
Power cord
“¬‡§‡∫‘≈°”≈—ß
C
Sleeve
ª≈Õ°ÀÿÈ¡
A/ B
Hard case/Control panel
≈—ß∫√√®ÿ/ÀπÈ“ª—¥
‰∑¬
™ÿ¥ª√–°Õ∫π’ȉ¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫ °√–·‰øøÈ““¬¥‘π¢—È«≈∫°√–·µ√ß 12 ‚«≈∑Ï À“°√∂¬πµÏ¢Õߧÿ≥‰¡Ë‰
¥È„™È√–∫∫π’È µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–·‰ø™Ë«¬ ´÷Ëß“¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕ߇’¬ß√∂¬πµÏ JVC
‡æ◊ËÕªÈÕß°—π°“√‡°‘¥‰øøÈ“≈—¥«ß®√ ¢Õ·π–π”„ÀȪ≈¥¢—È«·∫µ‡µÕ√’Ë≈∫ÕÕ° ·≈È«®÷ßµËÕ“¬‰ø°ËÕ𵑥µ—È߇§√◊ËÕß
•µ√«®Õ∫„ÀÈ·πË„®«Ë“‰¥È‡¥‘π“¬¥‘πµËÕ√–À«Ë“߇§√◊ËÕß°—∫µ—«∂—ß √∂¬πµÏ„À¡Ë·≈È«À≈—ß®“°µ‘¥µ—Èß
À¡“¬‡Àµÿ:
•„™Èæ‘°—¥®”‡æ“–·∑πø‘« À“°ø‘«Ï¢“¥∫ËÕ¬ „ÀȪ√÷°…“√È“ π¢“¬‡§√◊ËÕ߇’¬ß√∂¬πµÏ JVC
•¢Õ·π–π”„ÀȵËÕ≈”‚æß ∑’Ë¡’°”≈—ߢ—∫ßÿ¥‡°‘π°«Ë“ 50 W (∑—ÈߥȓπÀπÈ“·≈–¥È“πÀ≈—ß ¡’§Ë“§«“¡µÈ“π∑“π 4∂÷ß 8)
∂È“°”≈—ߢ—∫µË”°«Ë“ 50 W „Àȇª≈’ˬπ§Ë“ “AMP GAIN” ‡æ◊ËÕªÈÕß°—π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 16 §”·π–π”)
•°“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È«“¬µ–°—Ë« ∑’ˉ¡Ë„™È·≈È«¥È«¬‡∑ ªæ—π“¬‰ø
•·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈—ß®“°„™È √–¡—¥√–«—ßլ˓‰ª —¡º—‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È
Instal1-4_SV3205_006A_1.indd 1Instal1-4_SV3205_006A_1.indd 1 1/13/06 1:55:42 PM1/13/06 1:55:42 PM

Do the required electrical connections.
µËÕ“¬‰øµ“¡∑’Ë°”À𥉫È∑—ÈßÀ¡¥
Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are
used, they could damage the unit.
À¡“¬‡Àµ : ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È  °√Ÿ¬“«¢π“¥ 8 ¡¡. ∂È“„™È  °√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡  ’¬À“¬‰¥ô
Dashboard
·ºßÀπÈ“ª—∑¡á
2
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealers or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
„˧—π∫—ߧ—∫ 2 Õ—π≈ß„π√ËÕß”À√—∫„™Èæ—π≈«¥
¥—ß¿“æ ®“°π—Èπ „Àȇ≈◊ËÕπ™ÿ¥ª√–°Õ∫ÕÕ°
„π¢≥–∑’˧ËÕ¬ Ê¥÷ߧ—π∫—ߧ—∫∑—Èß Õß Õ—πÕÕ°®“°°—π
When installing the unit without using the sleeve / ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë„™Èª≈Õ°ÀÿÈ¡
In a Toyota car for example, first remove the car radio and install the unit in its place.
µ—«Õ¬Ë“߇™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ ·≈ô«®÷ßµ‘¥µíô߇§√◊ËÕßπ’ô‡¢ô“·∑π∑’Ë
When using the optional stay / ‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È
TROUBLESHOOTING
• The fuse blows.
*Are the red and black leads connected correctly?
• Power cannot be turned on.
*Is the yellow lead connected?
• No sound from the speakers.
*Is the speaker output lead short-circuited?
• Sound is distorted.
*Is the speaker output lead grounded?
*Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
*Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
*Is the speaker output lead grounded?
*Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
*Have you reset your unit?
°“√∂Õ¥™ÿ¥ª√–°Õ∫
°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀȪ≈¥ÀπÈ“µ—¥Ë«π∑È“¬°ËÕπ
°“√µ√«®Õ∫ª—≠À“¢—¥¢ÈÕß
•ø‘«ú¢“¥
*¡’°“√‡™◊ËÕ¡“¬µ–°—Ë«’¥”·≈–’·¥ßլ˓ß∂Ÿ°µÈÕßÀ√◊Õ‰¡ò
•‰¡Ë“¡“√∂‡ª‘¥‡§√◊ËÕ߉¥È
*¡’°“√‡™◊ËÕ¡“¬µ–°—Ë«’‡À≈◊ÕßÀ√◊Õ‰¡ò
•‰¡Ë¡’‡’¬ßÕÕ°®“°≈”‚æß
*“¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æ߇°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë
•‡’¬ß‡æ’Ȭπ
*“¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
*“¬¢—È«≈∫ “–” ¢Õß≈”‚æߥȓπ´È“¬ (L) ·≈–¢«“ (R) µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
•‡’¬ß√∫°«π
*¡’°“√„™È“¬—ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕßò«π∑’˵‘¥µ—Èß ‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë
•™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ
*“¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
*“¬¢—È«≈∫ “–” ¢Õß≈”‚æߥȓπ´È“¬ (L) ·≈–¢«“ (R) µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë
•‡§√◊ËÕß√—∫π’È∑”ß“π‰¡
*∑Ë“π‰¥Èµ—È߇§√◊ËÕß„À¡ËÀÈ√◊Õ¬—ß
*2 Not supplied for this unit.
*2 ‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È
Flat type screws (M5 ×8 mm)*2
°√ŸÀ—«‡√’¬∫ (M5 ×8 ¡¡.)*2
Pocket
°–‡ª“–
Flat type screws (M5 ×8 mm)*2
°√ŸÀ—«‡√’¬∫ (M5 ×8 ¡¡.)*2
Screw (option)
°√Ÿ (‡≈◊Õ°‰¥È)
Stay (option)
µ—«¬÷¥ (‡≈◊Õ°‰¥È)
Fire wall
ºπ—ß°—π‰ø
Install the unit at an angle of less than 30˚.
µ‘¥µ—Èß™ÿ¥ª√–°Õ∫∑’Ë¡ÿ¡µË”°«Ë“ 30˚ Õß»“
Bracket*2
·∑Ëπ√Õß√—∫*2
Bracket*2
·∑Ëπ√Õß√—∫*2
*1When you stand the unit, be
careful not to damage the fuse
on the rear.
*1‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—ßլ˓
∑”„ÀÈø‘«Ï∫√‘‡«≥Ë«π∑È“¬‡’¬À“¬
Bend the appropriate tabs to hold the
sleeve firmly in place.
ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀȵËÕ°—π‡¢È“∑’Ë
°“√µ‘¥µ—Èß (°“√ª√–°Õ∫·ºßÀπÈ“ª—∑¡Ï‡¢È“)
¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È·¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ª—≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’ˬ«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª√÷°…“°—∫ºŸÈ¢“¬‡§√◊ËÕ߇’
¬ß√∂¬πµÏ JVC ¢Õß∑Ë“πÀ√◊Õ∫√‘…—
•™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë „ÀÈÀ“™Ë“ߺŸÈ‡™’ˬ«™“≠‡ªÁπºŸÈµ‘¥µ—Èß
Instal1-4_SV3205_006A_1.indd 2Instal1-4_SV3205_006A_1.indd 2 1/13/06 1:55:55 PM1/13/06 1:55:55 PM

ENGLISH
B
Connecting the parking brake wire / µËÕ“¬‡∫√°¡◊Õ
When installing the monitor in a location where it can be seen by the driver
¡◊ËÕ®–µ‘¥µ—È߮աÕ𑇵Õ√Ï„πµ”·ÀπËß∑’˺ŸÈ¢—∫“¡“√∂¡Õ߇ÀÁπ‰¥È
Connect the parking brake wire to the parking brake system built in the car.
µËÕ“¬‡∫√°¡◊Õ°—∫√–∫∫‡∫√°¡◊Õ¢Õß√∂¬πµ
When installing the monitor in a location where it cannot be seen by
the driver
‡¡◊ËÕ®–µ‘¥µ—È߮աÕ𑇵Õ√Ï„πµ”·ÀπËß∑’˺ŸÈ¢—∫‰¡Ë“¡“√∂¡Õ߇ÀÁπ‰¥È
Connect the parking brake wire to metallic body or chassis of the car.
µËÕ“¬‡∫√°¡◊Õ°—∫µ—«∂—ß∑’ˇªÁπ‚≈À–À√◊Õ‚§√ß√∂¬πµ
Connecting the crimp connector / «‘∏’µËÕ¢—È«µËÕ”À√—∫Àπ’∫
C
Parking brake wire (light green)
“¬‡∫√°¡◊Õ (’‡¢’¬«ÕàÕπ)
To metallic body or chassis of the car
µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™´‘¢Õß√∂¬πµú
Parking brake switch (inside the car)
«‘µ™Ï‡∫√°¡◊Õ (¿“¬„π√∂)
Parking brake
‡∫√°¡◊Õ
Parking brake wire (light green)
“¬‡∫√°¡◊Õ (’‡¢’¬«ÕàÕπ)
To external components (see diagram )
™ËÕ߇’¬∫µËÕ¢ÕßÕÿª°√≥Ï¿“¬πÕ° (¥Ÿ·ºπ¿Ÿ¡‘ )
Light green
’‡¢’¬«ÕËÕπ
VIDEO OUT
(see diagram / ¥Ÿ·ºπ¿Ÿ¡‘ )
A
To parking brake, metallic body or chassis of the car
µËÕ°—∫‡∫√°¡◊Õ µ—«∂—ß∑’ˇªÁπ‚≈À– À√◊Õ‚§√ß√∂¬πµÏ
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause
serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1Connect the colored leads of the power cord in the order specified in the illustration below.
2Connect the antenna cord.
3Finally connect the wiring harness to the unit.
Black
’¥”
Blue with white stripe
πÈ”‡ß‘π≈“¬¢“«
Red
’·¥ß
Yellow *2
’‡À≈◊Õß *2
To metallic body or chassis of the car
µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™´‘¢Õß√∂¬πµú
Ignition switch
«‘∑™Ï®ÿ¥√–‡∫‘¥
Fuse block
·ºßø‘«
To an accessory terminal in the fuse block
µËÕ°—∫¢—È«Ë«πª√–°Õ∫„π·ºßø‘«
To the remote lead of other equipment (200 mA max.)
µËÕ‡¢È“°—∫Õª°√≥ÏÕË◊π (¢π“¥Ÿß¸¥ 200 mA
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
µµËÕ°—∫¢—È«∑’Ë¡’°√–·‰øøÈ“„π·ºßø‘«Ï ´÷ËßµËÕ°—∫·∫µ‡µÕ√’Ë√∂¬πµ
(‚¥¬‰¡ËµÈÕß„™È«‘∑™Ï®ÿ¥√–‡∫‘¥) (12 ‚«≈∑ϧß∑’Ë)
*1Not supplied for this unit.
*1‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È
Line out (see diagram )
“¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡‘ )
*2Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
*2 °ËÕπ°“√µ√«®Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µ—Èß
µÈÕßµËÕ“¬µ–°—Ë«π’È°ËÕπ ¡‘©–π—Èπ®–‰¡Ë“¡“√∂‡ª‘¥‡§√◊ËÕ߉¥È
Wire connecting the battery and the parking brake switch.
“¬∑’˵ËÕ°—∫·∫µ‡µÕ√’Ë·≈–«‘µ™Ï‡∫√°¡◊Õ
Attach the parking brake wire to this point.
Õ“¬‡∫√°¡◊Õ∑’Ë®ÿ¥π’È
Blue
»’øÈ“ To the automatic antenna if any (250 mA max.)
‡“Õ“°“»‰øøÈ“Õ—µ‚π¡—µ‘ À“°¡’ (¢π“¥Ÿß¸¥ 250 mA)
Typical connections / °“√‡™◊ËÕ¡µËÕ·∫∫ª°µ
ELECTRICAL CONNECTIONS
LINE IN
(see diagram / ¥Ÿ·ºπ¿Ÿ¡‘ )
Brown
’πÈ”µ“≈ To cellular phone system
µËÕ°—∫‚∑√»—æ∑χ§≈◊ËÕπ∑
Contact the metallic part of the crimp to the wires inside.
„ÀÈË«π∑’ˇªÁπ‚≈À–¢Õßµ—«Àπ’∫—¡º—°—∫“¬¢È“ß„π
Pinch the crimp firmly.
Àπ’∫„ÀÈ·πËπ
3
‰∑¬
°ËÕ•∑”°“•‡™•ËÕ¡µËÕ: µ•«®†Õ•°“•‡¥‘•†“¬‰ø„•••¬•µÏլ˓ߕ–¡—¥•–«—լ˓„ÀȺ‘¥æ•“¥„•°“•‡™•ËÕ¡µËÕ™ÿ¥ª•–°Õ•™ÿ¥•’
°“•‡™•ËÕ¡µËÕº‘¥æ•“¥Õ“®∑”„Àȇ°‘¥§«“¡‡’¬À“¬•È“¬·•ß°—•™ÿ¥ª•–
°Õ••’ȉ¥È“•µ–°—Ë«¢Õ߆“¬‰ø ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ—«• ß••Õ“®¡’’ ∑’ˉ¡Ë‡À¡•Õ•°—•
1µËÕ“¬‰ø’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß
2‡™◊ËÕ¡µËÕ°—∫“¬Õ“°“»
3ÿ¥∑È“¬ µËÕË«π§«∫§ÿ¡°“√‡¥‘π“¬‰ø‡¢È“°—∫™ÿ¥ª√–°Õ∫™ÿ¥π’È
°“√‡™◊ËÕ¡‚¥¬„™È‰øøÈ“
15 A fuse
ø‘«Ï¢π“¥ 15 A
Rear ground terminal
®ÿ¥‡™◊ËÕ¡µËÕ “¬¥‘π¥È“πÀ≈—ß
Antenna terminal
¢—È«µËÕ“¬Õ“°“»
Purple
’¡Ë«ß
Purple with black stripe
’¡Ë«ß·∂∫¥”
Green
’‡¢’¬«
Green with black stripe
’‡¢’¬«·∂∫¥”
Gray
’‡∑“
Gray with black stripe
’‡∑“·∂∫¥”
White
’¢“«
White with black stripe
’¢“«·∂∫¥”
Right speaker (rear)
≈”‚æߢ«“ (À≈—ß)
Left speaker (rear)
≈”‚æß´È“¬ (À≈—ß)
Right speaker (front)
≈”‚æߢ«“ (ÀπÈ“)
Left speaker (front)
≈”‚æß´È“¬ (ÀπÈ“)
Instal1-4_SV3205_006A_1.indd 3Instal1-4_SV3205_006A_1.indd 3 1/24/06 10:40:31 AM1/24/06 10:40:31 AM

AV1-IN
AV2-INPUT
D
4
Other external component / Õÿª°√≥Ï¿“¬πÕ°Õ◊ËπÊ
CAUTION / ¢ÈÕ§«√√–«—ß :
Before connecting the external components, make sure that the unit is turned off.
°ËÕπ®–‡™◊ËÕ¡µËÕ°—∫Õÿª°√≥Ï¿“¬πÕ° °√ÿ≥“µ√«®Õ∫„ÀÈ·πË„®«Ë“ªî¥‡§√◊ËÕßÕ¬ŸË
Connecting the external components / °“√µËÕ‡æ‘Ë¡‡µ‘¡‡¢È“°—∫Õÿª°√≥ÏÕ◊ËπÊ
JVC CD changer
JVC CD ‡™π‡®Õ√Ï
External component
Õÿª°√≥Ï¿“¬πÕ°
3.5 mm stereo mini plug
¢—È«‡’¬∫¡‘π‘‡µÕ√‘‚Õ¢π“¥ 3.5 ¡¡.
*8AUX Input Adapter KS-U58 (not supplied for this
unit)
*8Õ–·¥ª‡µÕ√Ï√—∫—≠≠“≥ AUX √ÿËπ KS-U58
(‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
•Set “EXT IN” for the external input setting (See page 16 of the INSTRUCTIONS.) / µ—Èߧ˓ “EXT IN”
‡∫ªìπ°“√§Ë“√—∫—≠≠“≥Õÿª°√≥Ï¿“¬πÕ° (¥ŸÀπÈ“ 16 §”·π–π”)
•Set “CHANGER” for the external input setting (See page 16 of the INSTRUCTIONS.) / µ—Èߧ˓ “CHANGER” ‡ªìπ°“√§Ë“√—∫—≠≠“≥Õÿª°√≥Ï¿“¬πÕ° (¥ŸÀπÈ“ 16 §”·π–π”)
*5iPod is a trademark of Apple
Computer, Inc., registered in the
U.S. and other countries.
*5iPod ‡ªÁπ‡§√◊ËÕßÀ¡“¬°“√§È“¢Õß
Apple Computer, Inc.
´÷Ëß®¥∑–‡∫’¬π°“√§È“„πª√–
‡∑»À√—∞Õ‡¡√‘°“·≈–ª√–‡∑»Õ◊ËπÊ
CD changer, Apple iPod®, or JVC D. player / CD ‡™π‡®Õ√Ï, Apple iPod®À√◊Õ‡§√◊ËÕ߇≈Ëπ JVC D.
F
E
CD changer
jack
™ËÕ߇’¬∫µËÕ¢Õß
‡§√◊ËÕ߇≈Ëπ CD
External component
Õÿª°√≥Ï¿“¬πÕ°
Connecting the external amplifier / °“√µËÕ‡æ‘Ë¡‡µ‘¡‡¢È“°—∫Õÿª°√≥ÏÕ◊ËπÊ
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker
leads of this unit unused.
§ÿ≥“¡“√∂µËÕ°—∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï ·–Õÿª°√≥ÏÕ◊òπʉ¥ô ‡æ◊ËÕ‡æ‘Ë¡§ÿ≥ ¿“æ‡’¬ß„ÀÈ°—∫√–∫∫‡µÕ√‘‚Õ¢Õß√∂¬πµÏ
•µËÕ“¬µ–°—Ë«√–¬–‰°≈ (’πÈ”‡ß‘π≈“¬¢“«) ‡¢È“°—∫“¬µ–°—Ë«√–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Ëπ Ê ‡æ◊ËÕ®–“¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√–
°Õ∫π’ȉ¥È
•∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È ·≈È«µËÕ‡¢È“°—∫‡§√◊ËÕߢ¬“¬ ∑‘Èß“¬µ–°—Ë«≈”‚æߢÕß™ÿ¥ª√–°Õ∫π’ȉ«È
Rear speakers
≈”‚æßÀ≈—ß
JVC Amplifier
‡§√◊ËÕߢ¬“¬‡’¬ß JVC
Remote lead
“¬µ–°—Ë«•–¬–‰°•
Y-connector (not supplied for this unit)
¢ÈÕµËÕ√Ÿªµ—« Y(‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
Remote lead (Blue with white stripe)
“¬µ–°—Ë«•–¬–‰°• (’πÈ”‡ß‘π≈“¬¢“«)
To the remote lead of other equipment or automatic antenna if any
µËÕ“¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡“Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’
*3Firmly attach the ground wire to the metallic body or to
the chassis of the car—to the place uncoated with paint (if
coated with paint, remove the paint before attaching the
wire). Failure to do so may cause damage to the unit.
*3 µËÕ≈«¥  “¬¥‘π„ÀÈ·πËπ‡¢È“°—∫µ—«∂—߇À≈Á° À√◊Õµ—«∂—ß√∂ —
µ√ß  Ë«π ∑’ˉ¡Ë¡’  ’‡§≈◊Õ∫ (À“°¡’  ’‡§≈◊Õ∫Õ¬ŸË „ÀÈ¢Ÿ¥  ’ÕÕ°°ËÕπ
°ËÕπµËÕ≈«¥
 “¬¥‘π) À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–π”π’È ‡§√◊ËÕßÕ“®™”√ÿ¥
À√◊Õ‡
 ’¬À“¬‰¥È
Connecting the monitor / °“√µËÕ®Õ¿“æ
KV-MR9010
9-INCH WIDESCREEN MONITOR
(not supplied)
¡Õ𑇵Õ√Ï’®Õ°«È“ß 9π‘È«
(‰¡Ë‰¥È„ÀÈ¡“æ√ÈÕ¡‡§√◊ËÕß)
Apple iPod
(separately purchased)
Apple iPod (·¬°®”ÀπË“¬)
JVC D. player
(separately purchased)
‡§√◊ËÕ߇≈Ëπ JVC D.
(·¬°®”ÀπË“¬)
CD changer jack
™ËÕ߇’¬∫µËÕ¢Õ߇§√◊ËÕ߇≈Ëπ CD
*4 Signal cord (not supplied for this unit)
*4“¬‡§‡∫‘≈—≠≠“≥ ( ‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
You can connect these components as illustrated below. The iPod*5or D. player can be connected using
an interface adapter (not supplied)—KS-PD100 (for iPod) or KS-PD500 (for D. player).
∑Ë“π“¡“√∂µËÕÕÿª°√≥Ï¥—ß°≈Ë“«µ“¡¿“æ·¥ß¥È“π≈Ë“ß ∑Ë“π“¡“√∂‡™◊ËÕ¡µËÕ iPod*5À√◊Õ‡§√◊ËÕ߇≈Ëπ D. ‚¥¬„™ÈÕ‘π‡∑Õ√χøÕ–
·¥ª‡µÕ√Ï (‰¡Ë¡’¡“„ÀÈ)—KS-PD100 (”À√—∫ iPod) À√◊Õ KS-PD500 (”À√—∫‡§√◊ËÕ߇≈Ëπ D.)
Video cord (not supplied)
“¬«‘¥’‚Õ (‰¡Ë‰¥È„ÀÈ¡“æ√ÈÕ¡‡§√◊ËÕß)
or
À√◊Õ
Rear side
¥â“πÀ≈—ß
Or / À√◊Õ
VIDEO OUT
External component
Õÿª°√≥Ï¿“¬πÕ°
*7Line Input Adapter KS-U57 (not supplied for
this unit)
*7Õ·¥ª‡µÕ√Ï “¬—≠≠“≥‡¢È“ KS-U57
(‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)
*6Connecting cord supplied for
your CD changer
*6µËÕ“¬∑’Ë„ÀÈ¡“”À√—∫ CD
‡™π‡®Õ√Ï
Before connecting the monitor, make sure the unit is turned off.
°ËÕπ®–µËÕ®Õ¿“æ ¢Õ„ÀÈ·πË„®«Ë“‰¥Èª‘¥‡§√◊ËÕß·≈È«
Front speakers
≈”‚æßÀπÈ“
Instal1-4_SV3205_006A_1.indd 4Instal1-4_SV3205_006A_1.indd 4 1/24/06 2:24:09 PM1/24/06 2:24:09 PM