JVC KW-AV70BT Guide

RM-RK252
30˚
Monitor panel
KW-AV70BT
KW-AV70
KW-AV70BT
KW-AV70
1
Parts list for installation and connection
The following parts are provided for this unit.
If anything is missing, contact your dealer immediately.
KW-AV70BT/KW-AV70
Installation/Connection Manual
ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC
car audio dealers.
WARNINGS
• DO NOT install any unit or wire any cable in a location where;
– it may obstruct the steering wheel and gearshift lever operations, as this may result in a traffic
accident.
– it may obstruct the operation of safety devices such as air bags, as this may result in a fatal
accident.
– it may obstruct visibility.
• DO NOT operate any unit while manipulating the steering wheel, as this may result in a traffic
accident.
• The driver must not watch the monitor while driving. It may lead to carelessness and cause an
accident.
• If you need to operate the unit while driving, be sure to look around carefully or you may be
involved in a traffic accident.
• If the parking brake is not engaged, “Parking Brake” appears on the monitor, and no playback
picture will be shown.
– This warning appears only when the parking brake lead is connected to the parking brake
system built in the car.
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and
make all electrical connections before installing the unit.
• Be sure to ground this unit to the car’s chassis again after installation.
• Be sure any cable is not caught on the car’s chassis or under seats.
Notes on electrical connections:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.
• It is recommended to connect speakers with maximum power of more than 50 W (both at the
rear and at the front, with an impedance of 4  to 8 Ω).
• To prevent short circuits, cover the terminals of the
UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful
not to touch it when removing this unit.
• At the time of installation, be sure to fix all wires
(wires both from this unit and from the car itself) in
a way that no wires can come into contact with heat
sinks on the rear and side of the unit.
Heat sink
LVT2305-002A
[A]
1211EHHMDWJEIN
EN
© 2011 JVC KENWOOD Corporation
Round head
screws
(M5 x 8 mm)
Flat head screws
(M5 x 8 mm)
Main unit
Power cord
Batteries
Remote controller
Crimp connector
Monitor panel and soft case
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments corresponding to
your specific car. If you have any questions or require information regarding installation kits, consult your JVC
car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used, parts could
become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
• You cannot install the unit on the car which has any obstacles in the space shown in “Required space for
installation and the monitor panel ejection” below.
1Remove the audio system originally installed in the car, together with its mounting brackets.
• Be sure to keep all the screws and parts removed from your car for future use.
2Attach the mounting brackets (removed from the car) to this unit (see below).
• Use flat head screws or round head screws, depending on installation location.
• When you need to use round head screws, use the supplied screws and the screws used to attach the metal
protection plates to the unit when shipped.
3Do the required electrical connections.
• See “ELECTRICAL CONNECTIONS” on pages 1 and 2.
4Install this unit using the screws removed in step 1.
5Attach the monitor panel (see below).
Install the unit at an angle of
less than 30˚.
Connecting the parking brake lead
Parking brake
Parking brake switch
(inside the car)
Parking brake lead
(light green)
To metallic body or
chassis of the car
Crimp
connector
ELECTRICAL CONNECTIONS
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise,
the unit will be seriously damaged.
• BEFORE connecting the speaker leads of
the power cord to the speakers, check the
speaker wiring in your car.
TROUBLESHOOTING
Supplied
screws
Mounting bracket
removed from the car
Screws removed from the car in step 1
Supplied screws
Select the
appropriate type
fitting to your
audio system space.
If necessary,
restore the
protruding tabs.
Step 5
When installing the unit in a Nissan car
If your Nissan car needs a plate, purchase the plate separately.
Plate for use with a
Nissan car (not supplied)
• When you use screws other than those
supplied, use 8 mm-long screws. If longer
screws are used, they could damage the
unit.
• Tighten the screws firmly to prevent the
unit from falling off.
Locate the reverse lamp lead in the trunk. Extension lead (not supplied for this unit)
Purple with
white stripe
Reverse lamps
To reverse lamps
Reverse lamp lead
Connecting the reverse gear signal lead (for rear view camera)
Crimp connector (not supplied
for this unit)
• The fuse blows.
*Are the red and black leads connected
correctly?
• Power cannot be turned on.
*Is the yellow lead connected?
• No sound from the speakers.
*Is the speaker output lead short-circuited?
• Sound is distorted.
*Is the speaker output lead grounded?
*Are the “–” terminals of L and R speakers
grounded in common?
• Noise interfere with sounds.
*Is the rear ground terminal connected to
the car’s chassis using shorter and thicker
cords?
• This unit becomes hot.
*Is the speaker output lead grounded?
*Are the “–” terminals of L and R speakers
grounded in common?
• This unit does not work at all.
*Have you reset your unit?
Remove the metal protection plates from the
unit before installation.
•
Keep the round head screws (M5 x 8 mm)
used to attach the metal protection plates.
You may need to use the screws for
installation.
The following example is for installation
in a Toyota car. For more details,
consult your JVC car audio dealer.
Extension lead
Extension lead
Required space for
installation and the monitor
panel ejection
160 91.6
100
20
4
Dashboard
Only for KW-AV70BT
Bag for storing the adapterMicrophoneBluetooth adapter
(attached)
KS-UBT1
1-2_KWAV70[A].indd 11-2_KWAV70[A].indd 1 11.12.20 3:36:02 PM11.12.20 3:36:02 PM

*2
*2
1
2
3
4
5
6
7
8
31
*1
PA R K I N G BRAKE
REVERSE
GEAR
SIGNAL
2
SUBWOOFER
OUT
DIRECT STEERING REMOTE
REMOTE
CONT
KW-AV70BT
KW-AV70
KW-AV70BT
KW-AV70
KW-AV70BT
KW-AV70BT
KW-AV70
KW-AV70BT
KW-AV70
KW-AV70BT/KW-AV70
KW-AV70BT
KW-AV70
2
Connecting to the steering wheel remote controller
A
Connecting the external amplifiers and subwoofer
B
Connecting the external components
F
Connecting an external navigation unit
E
Connecting the microphone (Only for KW-AV70BT)
C
1
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1Connect the colored leads of the power cord in the order specified in the illustration below.
2Connect the antenna cord.
3Finally connect the wiring harness to the unit.
See each diagram below.
Black
Yellow *3
Red
Orange with white stripe
Brown
Light green
Blue with white stripe
Blue
To the OE remote adapter *4
To metallic body or chassis of the car
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
To an accessory terminal in the fuse block
To car light control switch
To mobile phone system
To automatic antenna if any (250 mA max.)
To the remote lead of other equipment (200 mA max.)
Crimp connector
White with black stripe White Gray with black stripe Gray Green with black stripe Green Purple with black stripe Purple
Left speaker
(front)
Right speaker
(front)
Left speaker
(rear)
Right speaker
(rear)
10 A fuse
Fan
Rear ground
terminal
Antenna
terminal
If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
OE remote adapter *2 *5
Steering wheel remote controller (equipped in the car)
*6
*6
*6
*7*7
*7
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, and connect them to the amplifier. Leave the
speaker leads of this unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to
get clear sounds and to prevent internal heat built-up inside the unit.
See page 44 of the INSTRUCTIONS.
Subwoofer
JVC
Amplifier
JVC Amplifier
JVC
Amplifier
Remote lead *2
Front
speakers
Rear
speakers
To the remote lead of other equipment
Remote lead (blue
with white stripe)
Y-connector *2
*8
*6
*6
*8
Camcorder
etc. External
monitor
KV-CM10 / KV-CM20 *2 *9
Rear view camera
USB devices
USB cable (approx. 1 m)
USB device
Connecting the iPod or the iPhone
KS-U30
(not supplied)
USB 2.0 cable (accessory of the iPod/iPhone)
*1Only for KW-AV70BT.
*2 Not supplied for this unit.
*3 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot
be turned on. Do not connect the lead directly to the battery.
*4Do not connect the lead to any device other than the OE remote adapter. Doing so may cause malfunction.
*5 Alter the wire of the OE remote adapter to connect to the steering wheel remote lead.
*6Audio cord (not supplied for this unit).
*7Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if
coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
*8Video cord (not supplied for this unit).
*9KV-CM10 / KV-CM20 is not sold in some areas. For details, consult your JVC car audio dealer.
*10 When using the cable, you need to change the setting on the unit (see page 27 of the INSTRUCTIONS).
• iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
Connect an external navigation unit to the RGB input
terminal. The positional information detected on the
touch panel and picture signals from the navigation
unit are transferred through the terminal.
Refer to the manual of the external navigation unit for
details.
• Please contact your dealer to inquire about compatible navigation units.
• JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal.
External
navigation
unit *2
RGB input terminal
Fuse block
The terminals and cables of all models are shown in the
illustration for the purpose of explanation.
Ignition switch
(See page 1)
To parking brake (see page 1)
Secure the
microphone
cord using cord
cramps (not
supplied) if
necessary.
Microphone
Adhesive
tape
23
Blue with yellow stripe
Connecting the Bluetooth adapter (Only for KW-AV70)
D
To the brown lead of the
supplied power cord 7
To the blue with white
stripe lead of the supplied
power cord 5
Ground
*6
Blue with white stripe
Black
Brown
KS-BTA100
*2
See page 59 of the INSTRUCTIONS.
KW-AV70
• To watch video, connect the iPod/iPhone using JVC KS-U30 *10 (separately purchased), otherwise,
video is not displayed on the screen.
• To listen to music, connect the iPod/iPhone using a USB 2.0 cable (accessory of the iPod/iPhone).
Not used
1-2_KWAV70[A].indd 21-2_KWAV70[A].indd 2 11.12.20 3:36:07 PM11.12.20 3:36:07 PM