JVC GC-QX3HDU User manual

SERVICE MANUAL
No.86588
October 2000
GC-QX3HDU/GC-QX5HDU
DIGITAL STILL CAMERA
SPECIFICATIONS
STILL CAMERA
Power source
Power consumption
Dimensions
Weight
Operating temperature
Relative humidity
Storage temperature
LCD screen
Storage media
CCD
Focal distance
Lens
Video
Recording format
Sensitivity
Iris value (F value)
Exposure control
Exposure compensation
Minimum subject distance
Light measurement system
Flash
Recommended distance for flash
Shutter speed
White balance
Focus
: DC 5 V
: 3.6 W (when the LCD screen is off)
4.8 W (when the LCD screen is on)
: 111 (W) mm x 67 (H) mm x 59 (D) mm
(4-3/8" x 2-11/16" x 2-3/8") (except protruding parts)
: Approx. 290 g (0.64 lbs)
(without a Memory card and battery)
:0°C to 40°C (32°F to 104°F)
: 35% to 80%
: –20°C to 50°C (–4°F to 122°F)
: 2.0 inch, polysilicon TFT (200,000 pixels)
: SmartMediaTM 3.3V (up to 64MB)
: 3.34 million pixels (3.24 million valid pixels),
1/1.8" square pixels, primary color filter,
interlace scan CCD
: 7.5 mm to 17.5 mm
(equivalent to 37mm to 86 mm on a 35 mm still camera)
: 2.3X optical zoom lens
: 160 pixels x 120 pixels, 20 seconds, JVC original format
: Exif Ver. 2.1 (DCF compliant), TIFF (Uncompressed),
DPOF-compatible
: 80/160/320 (ISO compliant)
: F2.8/3.8, 5.6, 8, 11
: Program AE, iris priority AE
:±2EV (0.5EV steps)
: Approx. 2 cm to 50 cm (in Macro mode)
: Multi, spot
: Built-in,
Auto/red-eye prevention/forced/disabled
: Approx. 2.5 m
: Auto (Program AE: 1/8 seconds – 1/750 seconds,
Iris priority AE: 2 seconds – 1/750 seconds )
: Auto/Manual ( , , , MWB, )
: Auto/Manual
Self timer
Photo quality
Number of storable photos
(with an 8MB Memory card,
STANDARD/FINE/NO COMP.)
Battery
Printer connector
VIDEO output connector
Digital output connector
: 1 second, 8 seconds
: 3 modes (STANDARD/FINE/NO COMP.)
: 2032 x 1536: approx. 10/8/0
1024 x 768: approx. 43/32/3
640 x 480: approx. 87/65/8
: Lithium ion battery
: Output for optional printer
: Two-pole plug, 3.5 mm diameter (NTSC)
: Mini-USB connector
AC Power Adapter/Charger AA-V37
E. & O. E. Design and specifications subject to change without notice.
: AC 120 V`, 60 Hz
: AC 110 V – 240 V`, 50 Hz/60 Hz
: 14 W
: DC 3.6 V , 0.77 A
: DC 5.0 V , 1.5 A
:0°C to 40°C (32°F to 104°F)
[when charging: 10°C to 35°C (50°F to 95°F)]
: 68 (W) mm x 38 (H) mm x 110 (D) mm
(2-11/16" x 1-1/2" x 4-3/8")
: Approx. 230 g (0.51 lbs) (without a DC cord)
Power requirement
U.S.A. and Canada
Other countries
Power consumption
Output
Charge
Camera
Operating temperature
Dimensions
Weight
Regarding service information other than these sections, refer to the GC-QX3U service manual (No.86564).
Also, be sure to note important safety precautions provided in the service manual.

TABLE OF CONTENTS
Section Title Page
Important Safety Precautions
DIFFERENT TABLE
1. DISASSEMBLY
1.3.2 Disassembly method ( I ) ............................................ 1-1
2. ELECTRICAL ADJUSTMENT
2.1 ELECTRICAL ADJUSTMENT .......................................... 2-1
2.1.1 Precautions ................................................................. 2-1
2.1.2
Test instruments required for electrical adjustment ............. 2-1
2.1.3 Required test equipment ............................................ 2-1
2.1.4 Setup (LCD ADJUSTMENT) ........................................ 2-1
2.1.5 Setup (CCD ADJUSTMENT) ....................................... 2-2
2.2 Setup with patch cords and jig connector cables............ 2-3
3. CHARTS AND DIAGRAMS
NOTES OF SCHEMATIC DIAGRAM ........................................ 3-1
CIRCUIT BOARD NOTES ......................................................... 3-2
3.1 BOARD INTERCONNECTION ......................................... 3-3
3.2 MAIN (SYSCON) SCHEMATIC DIAGRAM ...................... 3-5
3.3 MAIN (DSP146) SCHEMATIC DIAGRAM ........................ 3-7
3.4 MAIN (DSP97) SCHEMATIC DIAGRAM .......................... 3-9
3.5 MAIN (CDS AGC A/D AND ARM ROM)
SCHEMATIC DIAGRAM ................... 3-11
3.6 MAIN (STROBE CONTROL AND AUDIO ) AND
STROBE FLASH SCHEMATIC DIAGRAMS ........ 3-12
3.7 MAIN (F/Z_MDA / IRIS) SCHEMATIC DIAGRAM ......... 3-13
3.8
JACK (VIDEO OUT/USB/PRINTER/DC JACK/
MONITOR BACK LIGHT) SCHEMATIC DIAGRAM .... 3-14
3.9 CCD SCHEMATIC DIAGRAM ........................................ 3-15
3.10 MONI REG (MONITOR) SCHEMATIC DIAGRAM ......... 3-16
3.11 MONITOR REG (DC/DC) SCHEMATIC DIAGRAM ........ 3-17
3.12 MAIN CIRCUIT BOARD (YB10299-01-01) ..................... 3-19
3.13 MAIN CIRCUIT BOARD (YB10299-01-03) ..................... 3-25
3.14 MONITOR REG CIRCUIT BOARD (YB10300-01-01) ..... 3-31
3.15 MONITOR REG CIRCUIT BOARD (YB10300-01-02) ..... 3-31
3.16 JACK CIRCUIT BOARD (YB10300-01-01) .................... 3-35
3.17 JACK CIRCUIT BOARD (YB10300-01-02) .................... 3-37
3.18 CCD CIRCUIT BOARD (YB10300-01-01) ...................... 3-39
3.19 CCD CIRCUIT BOARD (YB10300-01-02) ...................... 3-40
3.20
STOROBE FLASH CIRCUIT BOARD (YB10300-01-01) ... 3-41
3.21
STOROBE FLASH CIRCUIT BOARD (YB10300-01-02) ... 3-42
3.22 OVER ALL BLOCK DIAGRAM....................................... 3-43
4. PARTS LIST
4.1 PACKING AND ACCESSORY ASSEMBLY <M1> ........... 4-1
4.3 FINAL ASSEMBLY <M2> .............................................. 4-3
4.4 ELECTRICAL PARTS LIST ............................................... 4-6
MAlN BOARD ASSEMBLY <01> .................................... 4-6
CCD BOARD ASSEMBLY <02> .................................... 4-11
MONI REG BOARD ASSEMBLY <03> ......................... 4-12
JACK BOARD ASSEMBLY <04> .................................. 4-14
STROBE FLASH BOARD ASSEMBLY <05> ................. 4-15
The following table indicate main different features between models GC-QX3U, GC-QX3HDU and GC-QX5HDU.
Shooting Continuous Photos YES NO YES
Collage Mode YES NO YES
6M Pro-Still(Pixel Shift Mode) YES NO YES
DR Pro-Still(Wide Range Mode) YES NO YES
Installing the Film Copying Adapter NO NO YES
Shooting Film(Film Copy Mode) NO NO YES
MODEL GC-QX3U GC-QX3HDU
ITEM GC-QX5HDU
Operating Environment
The host computer that runs the Macintosh®
operating environment must satisfy the following
conditions.
USB Driver
1. USB-compatible computer (iMac™, iBook™,
Power Mac™ G3/G4, Power Book™ G3, etc.)
2. Mac OS 8.5.1/Mac OS 8.6/Mac OS 9.0
JVC Video Decoder
1. Power PC 603e/120MHz or faster
2. Mac OS 7.6.1 or later
3. QuickTime 3.0 or later
4. Minimum RAM requirement: 32MB
5. Minimum hard disk space requirement: 1MB
* Macintosh®is a registered trademark of Apple
Computer.
* Other trademarks are property of their respective
owners.
* If you use Macintosh®which does not have a USB
port, use an optional flash path, conversion card
adapter, etc. For details on the operating environ-
ment of these devices, contact the dealers or
manufacturers.
SOFTW ARE SECTION FOR Macintosh®
Operating Environment
SOFTW ARE SECTION FOR Windows®
The host computer that runs the Windows®
operating environment must satisfy the following
conditions.
USB Driver
1. Microsoft®Windows®98/Windows®98 Second
Edition, Full version (Not Upgrade)/Windows®
2000 Professional (Not Upgrade)
2. Available USB port
3. CD-ROM drive
Video Player
1. CPU: Intel®Pentium®200MHz class or higher
2. Microsoft®Windows®95/Windows®98
3. Display capability of 65,536 colors or more
4. CD-ROM drive
5. Minimum RAM requirement: 32MB
6. Minimum hard disk space requirement: 1MB
* The system requirements information is not a
guarantee that provided software applications will
work on all personal computers meeting those
requirements.
* Microsoft®, Windows®are either registered
trademarks or trademarks of Microsoft corporation
in United States and/or other countries.
* Intel®, Pentium®are registered trademarks of Intel
corporation.
* Other trademarks are property of their respective
owners.
* If you use Windows®95 or a personal computer
which does not have a USB port, use an optional
flash path, conversion card adapter, etc. For
details on the operating environment of these
devices, contact the dealers or manufacturers.

Note : Mark –– is not used.
The following table indicate different parts number between models GC-QX3U, GC-QX3HDU and GC-QX5HDU.
1 PACKING CASE LY31465-002A LY31465-013A LY32048-002A
2 POLY BAG LY30023-016A LY30023-016A +
3 CUSHION LY31466-001A LY31466-001A +
4 SHEET LY42548-001A –––– ––––
5 HOOD(OP) LY31822-001A –––– ––––
5A POLY BAG QPA01001505 –––– ––––
9 CD-ROM ASSEMBLY LY31074-007A LY31133-018A +
13 FILM COPY ADAP. –––– –––– LY20687-001A
14 FILM HOLDER AS –––– –––– LY32047-001A
15 CUSHION(ACC) –––– –––– LY32050-001A
19 CABLE ASSY(AUDIO/VIDEO) –––– QAM0297-001 +
20 POLY BAG –––– QPA01202505 +
27 MEDIA CARD ASSY LY31737-001A +LY31737-002A
!31 INST.BOOK(EN) LYT0543-001C LYT0668-001C LYT0668-001A
!32 INST.BOOK(FR) LYT0543-002A LYT0668-002C LYT0668-002A
!33 INST.BOOK(SP) LYT0543-003A LYT0668-003C LYT0668-003A
MODEL GC-QX3U
ITEM
PACKING ASSEMBLY <M1>
REF NO. GC-QX3HDU GC-QX5HDU
Note : Mark –– is not used.
103 BOARD HOLDER ASSEMBLY LY31457-002A +LY31457-007B
107C SHEET LY42322-001A –––– ––––
110 TOP COVER ASSEMBLY LY31460-003A LY31460-009A LY31460-008B
111 OPERATION UNIT LY20521-002C LY20521-002D LY20521-007B
113 SPACER(A) LY30029-016A –––– ––––
118 MICROPHONE –––– LY31454-001A +
125 S.SHEET(FFC) LY42506-001A –––– ––––
130 SHEET –––– LY42890-001A +
131 SPACER(A) –––– LY30029-0C2A +
152 REAR COVER ASSEMBLY LY20519-003B LY20519-009A LY20519-010A
153 FRONT COVER ASSEMBLY LYH20147-001A LYH20222-003A LYH20222-002A
153A FRONT COVER LY20516-003A LY20516-009A LY20516-008A
153B GRIP LY42320-001A LY31444-001A +
MODEL GC-QX3U
ITEM
FINAL ASSEMBLY <M1>
REF NO. GC-QX3HDU GC-QX5HDU
203 OPTICAL BLOCK ASSEMBLY LY31490-001B LY31490-004A +
221 TILT FRAME *LY20716-001A ++
MODEL GC-QX3U
ITEM
OP BLOCK ASSEMBLY <M3>
REF NO. GC-QX3HDU GC-QX5HDU
Note : Mark –– is not used.
Note : Mark * is GC-QX3U was also changed.

PW1 MAIN BOARD ASSEMBLY YB10282B-06 YB10299K-03 YB10299U-01
MODEL GC-QX3U
ITEM
MAIN BOARD ASSEMBLY <01>
REF NO. GC-QX3HDU GC-QX5HDU
PW1 CCD BOARD ASSEMBLY YB10283A1-04 YB10300K1-02 YB10300U1-01
MODEL GC-QX3U
ITEM
CCD BOARD ASSEMBLY <02>
REF NO. GC-QX3HDU GC-QX5HDU
PW4 MONI REG BOARD ASSEMBLY YB10283A4-04 YB10300K4-02 YB10300U4-01
MODEL GC-QX3U
ITEM
MONI REG BOARD ASSEMBLY <03>
REF NO. GC-QX3HDU GC-QX5HDU
PW2 JACK BOARD ASSEMBLY YB10283A2-04 YB10300K2-02 YB10300U2-01
MODEL GC-QX3U
ITEM
JACK BOARD ASSEMBLY <04>
REF NO. GC-QX3HDU GC-QX5HDU
PW3 STROBE BOARD ASSEMBLY YB10283A3-04 YB10300K3-02 YB10300U3-01
MODEL GC-QX3U
ITEM
STROBE BOARD ASSEMBLY <05>
REF NO. GC-QX3HDU GC-QX5HDU

Important Safety Precautions
Prior to shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes
of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the
following precautions when a set is being serviced.
Fig.1
1. Locations requiring special caution are denoted by labels and
inscriptions on the cabinet, chassis and certain parts of the
product. When performing service, be sure to read and com-
ply with these and other cautionary notices appearing in the
operation and service manuals.
2. Parts identified by the symbol and shaded ( ) parts are
critical for safety.
Replace only with specified part numbers.
Note: Parts in this category also include those specified to com-
ply with X-ray emission standards for products using
cathode ray tubes and those specified for compliance
with various regulations regarding spurious radiation
emission.
3. Fuse replacement caution notice.
Caution for continued protection against fire hazard.
Replace only with same type and rated fuse(s) as specified.
4. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
5. Use specified insulating materials for hazardous live parts.
Note especially:
1) Insulation Tape 3) Spacers 5) Barrier
2) PVC tubing 4) Insulation sheets for transistors
6. When replacing AC primary side components (transformers,
power cords, noise blocking capacitors, etc.) wrap ends of
wires securely about the terminals before soldering.
Power cord
Fig.2
10. Also check areas surrounding repaired locations.
11. Products using cathode ray tubes (CRTs)
In regard to such products, the cathode ray tubes themselves,
the high voltage circuits, and related circuits are specified for
compliance with recognized codes pertaining to X-ray emission.
Consequently, when servicing these products, replace the cath-
ode ray tubes and other parts with only the specified parts.
Under no circumstances attempt to modify these circuits.
Unauthorized modification can increase the high voltage value
and cause X-ray emission from the cathode ray tube.
12. Crimp type wire connector
In such cases as when replacing the power transformer in sets
where the connections between the power cord and power
transformer primary lead wires are performed using crimp type
connectors, if replacing the connectors is unavoidable, in or-
der to prevent safety hazards, perform carefully and precisely
according to the following steps.
1) Connector part number : E03830-001
2) Required tool : Connector crimping tool of the proper type
which will not damage insulated parts.
3) Replacement procedure
(1) Remove the old connector by cutting the wires at a point
close to the connector.
Important : Do not reuse a connector (discard it).
Fig.7
cut close to connector
Fig.3
(2) Strip about 15 mm of the insulation from the ends of
the wires. If the wires are stranded, twist the strands to
avoid frayed conductors.
15 mm
Fig.4
(3) Align the lengths of the wires to be connected. Insert
the wires fully into the connector.
Connector
Metal sleeve
Fig.5
(4) As shown in Fig.6, use the crimping tool to crimp the
metal sleeve at the center position. Be sure to crimp fully
to the complete closure of the tool.
1
v
Precautions during Servicing
7. Observe that wires do not contact heat producing parts
(heatsinks, oxide metal film resistors, fusible resistors, etc.)
8. Check that replaced wires do not contact sharp edged or
pointed parts.
9. When a power cord has been replaced, check that 10-15 kg of
force in any direction will not loosen it.
1.25
2.0
5.5
Crimping tool
Fig.6
(5) Check the four points noted in Fig.7.
Not easily pulled free Crimped at approx. center
of metal sleeve
Conductors extended
Wire insulation recessed
more than 4 mm
S40888-01

v
Safety Check after Servicing
Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been
returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compli-
ance with safety standards.
1. Insulation resistance test
Confirm the specified insulation resistance or greater between power cord plug prongs and
externally exposed parts of the set (RF terminals, antenna terminals, video and audio input
and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below.
2. Dielectric strength test
Confirm specified dielectric strength or greater between power cord plug prongs and exposed
accessible parts of the set (RF terminals, antenna terminals, video and audio input and output
terminals, microphone jacks, earphone jacks, etc.). See table 1 below.
3. Clearance distance
When replacing primary circuit components, confirm specified clearance distance (d), (d’) be-
tween soldered terminals, and between terminals and surrounding metallic parts. See table 1
below.
4. Leakage current test
Confirm specified or lower leakage current between earth ground/power cord plug prongs
and externally exposed accessible parts (RF terminals, antenna terminals, video and audio
input and output terminals, microphone jacks, earphone jacks, etc.).
Measuring Method : (Power ON)
Insert load Z between earth ground/power cord plug prongs and externally exposed accessi-
ble parts. Use an AC voltmeter to measure across both terminals of load Z. See figure 9 and
following table 2.
5. Grounding (Class 1 model only)
Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in,
Video out, Audio in, Audio out or Fixing screw etc.).
Measuring Method:
Connect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications.
d'
d
Chassis Power cord,
primary wire
Region
USA & Canada
Europe & Australia
Grounding Impedance (Z)
Z 0.1 ohm
Z 0.5 ohm
≤
≤
AC inlet
Earth pin
Exposed accessible part
Milli ohm meter
Grounding Specifications
Fig. 10
ab
c
V
Externally
exposed
accessible part
Z
Fig. 9
Fig. 8
Clearance Distance (d), (d')
d, d' 3 mm
d, d' 4 mm
d, d' 3.2 mm
1 MΩR 12 MΩ/500 V DC
Dielectric Strength
AC 1 kV 1 minute
AC 1.5 kV 1 miute
AC 1 kV 1 minute
AC Line Voltage
100 V
100 to 240 V
110 to 130 V
110 to 130 V
200 to 240 V
Japan
USA & Canada
Europe & Australia R 10 MΩ/500 V DC
Region
Insulation Resistance (R)
R 1 MΩ/500 V DC
≤
≤
≥≥
≤
≤
≤≤
≤
≤
AC 3 kV 1 minute
(Class 2)
AC 1.5 kV 1 minute
(Class 1)
d 4 mm
d' 8 mm (Power cord)
d' 6 mm (Primary wire)
Table 1 Specifications for each region
a, b, cLeakage Current (i)AC Line Voltage
100 V
110 to 130 V
110 to 130 V
220 to 240 V
Japan
USA & Canada
i 1 mA rms Exposed accessible parts
Exposed accessible parts
Antenna earth terminals
Other terminals
i 0.5 mA rms
i 0.7 mA peak
i 2 mA dc
i 0.7 mA peak
i 2 mA dc
Europe & Australia
Region Load Z
≤
≤
≤
≤
≤
≤
1 kΩ
2 kΩ
1.5 kΩ
0.15 µF
50 kΩ
Table 2 Leakage current specifications for each region
Note: These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.
2S40888-01

SECTION 1
DISASSEMBLY
1-1
1FRONT CASE Remove screws
REAR CASE 2 (115), 3 (156), 4 (157), 1 (154)
2OPERATION UNIT Remove the Connector Remove screws Note 1
rMAIN CN4001 OPERATION UNIT 3 (116)
Remove the TOP COVER 2 (115)
3STROBE BOARD ASSEMBLY Remove the Connector Remove screw Note 1
nMAIN CN6601 STROBE CN6501 1 (114) Note 2
JACK BOARD ASSEMBLY Remove the Connector Remove screws
pMAIN CN5501 JACK CN101 2 (114)
mLCD MODULE (BL) JACK CN701 e(SD3), f(SD4), g(SD5)
4LCD MODULE Remove the Connector Remove screws Note 1
kMAIN CN3002 LCD MODULE (LCD) 2 (114) Note 3
Remove from the Frame Assy
Remove from the LCD Holder
5MAIN BOARD ASSEMBLY Remove the Connector Note 1
hMAIN CN501 OP UNIT
zMAIN CN2501 MIC
cMAIN CN3001 MON/REG CN9001
dMON/REG TL9001 Frame Assy d(SD1)
MONI/REG BOARD ASSEMBLY Remove the PWB HOLDER Remove screws 2 (114) Note 1
6OP UNIT Remove from the Frame Assy Remove screws 3 (117)
1.3.2 Disassembly method ( I )
STEP
Note 1
Destination of connectors.
Note :Three kinds of double-arrows in connection tables
respectively show kinds of connector/wires.
: Board to Board connector
: Flat wire
: Wire
Note 2
Be careful from electric shock hazard because the capacitor
(C6512) for the strobe is exposed. Be sure to positively dis-
charge the capacitor if it is energized by short-circuiting a
resistor (10 - 22 k ) connected at both capacitor terminals.
Please be very careful when doing this job.
Note 3
LCD panel is fixed by four hooks of backlight.
Insert LCD panel in a hook firmly.
POINTFIG. NO.
PART NAME
CONNEC- NO.OF CONNECTION
TOR/HL PINS
c80 MAIN Board CN3001 MONI/REG Board CN9001
d1 MONI/REG Board TL9001 MAIN FRAME (RED)
e1 JACK Board TP3 MAIN FRAME (BROWN)
f1 JACK Board TP2
MONI/REG Board J9001 (BLACK)
g1 JACK Board TP1
MONI/REG Board J9002 (RED)
h22 MAIN Board CN501 OP UNIT
j2 MAIN Board CN502 OP UNIT
k24 MAIN Board CN3002 LCD MODULE (LCD)
m2 JACK Board CN701 LCD MODULE (BL)
n14 MAIN Board CN6601 STROBE Board CN6501
p38 MAIN Board CN5501 JACK Board CN101
q28 MAIN Board CN2001 CCD Board CN1001
r12 MAIN Board CN4001 OPERATION UNIT
s1
STROBE UNIT WIRE (ORANGE) STROBE Board J6501 (Through hole)
t1
STROBE UNIT WIRE (BROWN) STROBE Board J6502 (Through hole)
u1 STROBE UNIT WIRE (RED)
STROBE Board J6503 (Through hole)
v1
STROBE UNIT WIRE (BLACK) STROBE Board J6504 (Through hole)
w1
STROBE UNIT WIRE (Red, Thin wire) STROBE Board J6505 (Through hole)
x1
STROBE UNIT WIRE (BLACK, Thin wire) STROBE Board J6506 (Through hole)
z2 MAIN CN2501 MIC
Fig
1-3-1
Fig
1-3-2
Fig
1-3-1
Fig
1-3-3
NOTE
Note 5
Stick to let it pass between LEDs.Stick to
come out on the left of the sheet metal of
a video terminal.
no
slippege
4 sprts locked
161
NOTE : This service manual has indicated only the item different from GC-QX3U No.86564.

1-2
Fig.1-3-2
114
117
117
118
F
101
103
114
B
A
C
j
p
p
q
g
ee
d
B
C
m
f
gf
j
hqk
c
CCD BOARD ASSY
< 03 >
MAIN BOARD ASSY
< 01 >
MONI/REG BOARD ASSY
< 02 >
JACK BOARD ASSY
< 04 >
114
109
107B 105
107A
107
104
106
(SD2)
(SD1)
(SD3)
(SD4)
(SD5)
OP BLOCK ASSY
<M3>
A
108
114
k
m
h
d
5
5
6
6
3
4
125
129
130
161
Pass this through the inside of the boss.
Note 5

2-1
SECTION 2
ELECTRICAL ADJUSTMENT
2.1 ELECTRICAL ADJUSTMENT
2.1.1 Precautions
Both the camera section and deck section of this model
are designed and manufactured to be adjustment-free.
However, if both or either of the following parts is replaced,
it needs special adjustment with a personal computer at a
JVC service equipment after the part replacement
• OP block assembly
• EEPROM (on the MAIN board)
When there is some trouble in the electric circuit, it is required
to detect the faulty part with specified test instruments first
and then to proceed to repair, replacement and adjustment.
1. When cheking a signal at a chip test point, be sure to use
an IC clip or the like not to apply any stress to the test point.
When replacing a chip part (IC in particular), completely
remove solder chips from it and its periphery before
proceeding to part replacement (in order to avoid exfoliation
of the pattern).
2. Carefully disconnect/connect connectors because they
are apt to get damaged.
2.1.2 Test instruments required for electrical
adjustment
2.1.4 Setup (LCD ADJUSTMENT)
Setup for electrical adjustment with personal computer
Note 1:
As a general rule for adjustment with a personal
computer, connect a personal computer to its
PRINTER terminal.
Note 2: Use DC cord to supply the power.
2.1.3 Required test equipment
1. Color TV monitor.
2. AC power adapter (AA-V37 or equivalent)
3. Oscilloscope (dual-trace type, for more than 20 MHz).
4. Digital voltmeter
5. Frequency counter (with threshold level adjuster)
6. Personal computer
PC cable
QAM0099-002 Personal computer
RS-232C
port
Service support system
YTU94057-49
MENU
PRINTER
Fig. 2-1-1 Setup for electrical adjustment with
personal computer (I)
12
Patch cord ASSY
YTU93105 Jig connector cable
YTU93104B
6
7
INF adjustment lens
YTU92001B
Camera stand
YTU93079
5
Light box assembly
YTU93096A
34
8
Jig connector cable
YTU93106A
PC cable
QAM0099-002
Service support system
YTU94057-49
9Gray scale chart
YTU94133A
Cleaning cloth
KSMM-01
10 Color bar chart
YTU94133C
11
Smart media card
16MB
12 USB
QAM0252-001
13

2-2
Jig connector cable
(YTU93106A)
Fig. 2-1-2 Setup for electrical adjustment with
personal computer (II)
2.1.5 Setup (CCD ADJUSTMENT)
Setup for electrical adjustment with personal computer
Note 1:
As a general rule for adjustment with a personal
computer, connect a personal computer to its
DIGITAL terminal.
Note 2: Use DC cord to supply the power.
Fig. 2-1-3 Setup for electrical adjustment with
personal computer (I)
Personal computer
USB
port
Service support system
YTU94057-49
16MB
Smart media
Card
MENU
USB
Table 2-1-1 Jig Connector Function
Pin No. FUNCTION
1 AL3.3V
2 AL3.3V
3 JTAGMODE
4 135TDI
5 135nTRST
6 32RST
7 32nTRST
8 32TDO
9 32TCK
10 M_BLUE
11 RPD
12 M_PSIG
13 M_GREEN
14 NC
15 GND
16 AL3.3V
17 NC
18 135TMS
19 135TDO
20 135TCK
21 32DBI
22 32TMS
23 32TDI
24 NC
25 M_COM
26 M_SIG_C
27 M_RED
28 M_SIG_GND
29 GND
30 GND
Pin No FUNCTION

2-3
2.2 Setup with patch cords and jig connector cables
Note:
Fig. 2-2-1 shows an example of expansion setup that facilitates inspection of major boards because main components are
connected by means of patch cords and jir cables.For proceeding to electrical adjustment in such the setup, disassemble the
set at certain level required for the current adjustment objectives referring to the section 1 "DISASSEMBLY" and properly set
up the expanded set and test instruments.
MENU
VIDEO
DIGITAL
DC
5V
PRINTER
OP BLOCK/CCD
MON/REGMON/REG
JACK
MAIN
STROBE
MONITOR
OPERATION UNIT
Personal computer
MIC
CN9001
CN7101
CN101
CN6501
CN6601
CN2001
CN3002
CN501
CN5501
CN3001
CN2002
CN4001
CN502
CN2501
YTU94077-12
YTU94074-12
1
2YTU94126B-80
6YTU93106A
3YTU94077-28
4YTU94077-38
YTU94077-22
YTU94071-22
5
Fig. 2-2-1
Connection
1MAIN CN4001 OPRATION UNIT 12 YTU94077-12 FPC wire
YTU94074-12 FPC CN.ASSY
2MAIN CN3001 MON/REG CN9001 80 YTU94126B-80 B TO B CN.ASSY
3MAIN CN2001 CCD CN1001 28 YTU94077-28 FPC wire
4MAIN CN5501 JACK CN101 38 YTU94077-38 FPC wire
5MAIN CN501 OPUNIT 22 YTU94077-22 FPC wire
YTU94074-22 FPC CN.ASSY
6MAIN CN2202 30 YTU93106A JIG CN.cable
Pin No. Parts Number

JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
Head office
East Coast
Midwest
West Coast
Atlanta
Hawaii
:
:
:
:
:
:
1700 Valley Road Wayne, New Jersey 07470-9976
10 New Maple Avenue Pine Brook, New Jersey 07058-9641
705 Enterprise Street Aurora, Illinois 60504-8149
5665 Corporate Avenue Cypress, California 90630-0024
1500 Lakes Parkway Lawrenceville, Georgia 30043-5857
2969 Mapunapuna Place Honolulu, Hawaii 96819-2040
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
JVC CANADA INC.
Head office
Montreal
Vancouver
:
:
:
21 Finchdene Square Scarborough, Ontario M1X 1A7
16800 Rte Trans-Canadienne, Kirkland, Quebec H9H 5G7
13040 Worster Court Richmond, B.C. V6V 2B3
[phone]
[phone]
[phone]
Printed in Japan
S40895-03

SECTION 3
CHARTS AND DIAGRAMS
NOTES OF SCHEMATIC DIAGRAM
Safety precautions
The Components identified by the symbol are
critical for safety. For continued safety, replace safety
critical components only with manufacturer's recom-
mended parts.
1. Units of components on the schematic diagram
Unless otherwise specified.
1) All resistance values are in ohm, 1/6 W, 1/8 W (refer to
parts list).
Chip resistors are 1/16 W.
K: KΩ(1000Ω), M: MΩ(1000KΩ)
2) All capacitance values are in µF, (P: PF).
3) All inductance values are in µH, (m: mH).
4) All diodes are 1SS133, MA165 or 1N4148M (refer to parts
list).
2. Indications of control voltage
AUX : Active at high
AUX or AUX(L) : Active at low
4. Voltage measurement
1) Video circuits
Voltageare DC-measured (referencetoground)withavolt-
meter by suppling the color bar signal during print screen
mode.
— : Unmeasurable or unnecessary to measure
2) Indication on schematic diagram
Voltageindications on the schematic diagramareasshown
below.
123
2.5 1.8
Note: If the voltages are not indicated on the schematic
diagram, refer to the voltage charts.
5. Waveform measurement
1) Video circuits
Waveformsaremeasured(referencetoground)withacolor
bar signal during print screen mode.
2) Indication on schematic diagram
Waveform indications on the schematic diagram are as
shown below.
24
C331
11/10
22201816
WF25
C329
0.1/50 C330 0.1/50
R344
47K
R343
18K R345
10K
R346
15K
Measurement point
Waveform number
3) Waveform indications
Waveform number
WF25
1.2 Vp-p
50 mV/2 msec/DIV
Waveform name or
measurement point
Level : 1.2 Vp-p
ALC OUT
Oscilloscope Volts and Time/Division, Probe 10 : 1
3. Interpreting Connector indications
1
2
3
1
2
3
1
2
3
1
4
23
Removable connector
Wire soldered directly on board
Non-removable Board connector
Board to Board
Connected pattern on board
The arrows indicate signal path
3-1

CIRCUIT BOARD NOTES
1. Foil and Component sides
1) Foil side (B side) :
Parts on the foil side seen from foil face (pattern face)
are indicated.
2) Component side (A side) :
Parts on the component sideseen from component face
(parts face) indicated.
2. Parts location guides
Parts location are indicatedbyguidescaleon the circuit board.
Note:
For general information in service manual,please refer
to the Service Manual of GENERAL INFORMATION Edi-
tion 4 No. 82054D (January 1994).
6. Signal path Symbols
The arrows indicate the signal path as follows.
Memory screen main signal path
Memory screen and E-E signal path
E-E main signal path
(Example)
R-Y
YMemory screen R-Y signal path
E-E Y signal path
7. Indication of the parts for adjustments
The parts for the adjustments are surrounded with the circle as
shown below.
8. Indication of the parts not mounted on the circuit board
“OPEN” is indicated by the parts not mounted on the circuit
board.
R216
OPEN
REF No. LOCATION
IC Category: IC
Horizontal “A” zone
Vertical “6” zone
B : Foil side
(A : Component side)
C : Chip component
(D : Discrete component)
IC101 B C 6A
3-2

3.1 BOARD INTERCONNECTION
3-3 3-4
CN501
AHD1
TMS
FOCUS4
CN2002
PORT_04PORT_04 CLKFMC
CN6501
F_OUT_A
REG_15.0V
REG_3.3V
CN5501
Z_OUT_A
REG_-7.5V
A/D0
A/D1
A/D2
A/D3
RESET
SLF_LED
CN502
CN6601
REG_2.5V
TCK
TCK
AM_ADRS0 AVD2 AHD1 AHD2 FLD1 FLD2
DATA0
PWAD
HDENC VDENC
REG_4.8V
FLS_RST
A/D4
A/D5
CN101
CN4001
A/D6
A/D7
A/D8
A/D9
A/D0
A/D1
A/D2
A/D3
A/D4
A/D5
A/D6
A/D7
A/D8
A/D9
MAINCLK
FOCUS3
REG_6.3V REG_4.8V REG_3.3V F_OUT_B
VSUB_CNT
SYS_RST
F_OUT_C
ID
REG_3.3V
F_LED FSL_R_B FSL_R_A
CN3001
CHKUNREG
CN9001
UNREG
FSL_R+ FSL_R-
SHUTTER
FOCUS2 FOCUS1 ZOOM2 ZOOM1 SO- SO+ F/Z_VCC F_LED F_PTR_AD
HGOUT+
HGVCC+
HGVSS-
HGOUT-
DUMP-
MAINCLK
DRIVE+
DUMP+
PORT_05PORT_05 WTH
WTH
A_WTL 97TDO
97TDO 96TDO
GND
REG_4.8V
SHP
SHD
PBLK
CLPDM
ADCLK
OBCLP
SO_O
SCK_O
TG_CS
VDTG
HDTG
96TDO
97TMS 97TMS
GND
CLK36
PWAD
FLS_RST
CN2501
MCLK
SCLK
RESET TRST
IRIS_PWM
PORT_05 WTH A_WTL TCK
PORT_02
PORT_02
PORT_01PORT_01
REG_3.3V REG_4.8V GND
REG_15.0V
SCK_O CDS_CS TG_CS
PWR_CTL
SO_O
SO_O
SCK_O
CDS_CS
TG_CS
LCD_SO
LCD_SCK
M_EVR MON_CS
R-Y
B-Y
Y
TRST
CN3002
GND
GND
REG_3.3V
REG_2.5V
F_WE A_WTL CLK32 CE2 F_WE CLK32
IRIS_O/C
HOLE_AD
XSDEN
SRCLK
PRIN_RX
PRIN_TX
SDI
SI_8
D/A_YCOUT
ADO_3.0V
ADO_4.8V
PWDA
TRST
TMS
JACK_CTL
INT3 INT3
135_RX 135_TX
135_RX 135_TX
DSEL_0DSEL_0
DMAIY0
DMAIY1
DMAIY2
DMAIY3
DMAIY4
DMAIY5
DMAIY6
DMAIY7
DMAIRB0
DMAIRB1
DMAIRB2
DMAIRB3
DMAIRB4
DMAIRB5
DMAIRB6
DMAIRB7
DMAY00
DMAY01
DMAY02
DMAY03
DMAY04
DMAY05
DMAY06
DMAY07
DMAC00
DMAC01
DMAC02
DMAC03
DMAC04
DMAC05
DMAC06
DMAC07
32_D00
32_D01
32_D02
32_D03
32_D04
32_D05
32_D06
32_D07
32_D08
32_D09
32_D10
32_D11
32_D12
32_D13
32_D14
32_D15
32_A07
32_A08
32_A09
32_A10
32_A11
32_A12
32_A13
32_A14
32_A15
32_A16
32_A17
32_A18
32_A19
32_A20
32_A21
32_A22
32_A23
32_A24
32_A25
32_A26
32_A27
32_A28
32_A29
DATA2
32_A30
DMAIY0
DMAIY1
DMAIY2
DMAIY3
DMAIY4
DMAIY5
DMAIY6
DMAIY7
DMAIRB0
DMAIRB1
DMAIRB2
DMAIRB3
DMAIRB4
DMAIRB5
DMAIRB6
DMAIRB7
DMAY00
DMAY01
XRS
DMAY02
DMAY03
97TDI
DATA3
DMAY04
DMAY05
32TDI
DATA0 ADD10 97TDI ADD9 ADD8
DMAY06
DMAY07
DMAC00
DMAC01
DMAC02
DMAC03
DMAC04
DMAC05
DMAC06
ADD7 ADD6
DMAC07
32_D00
32_D01
32_D02
DATA1 DATA4
32_D03
32_D04
32_D05
32_D06
32_D07
32_D08
32_D09
32_D10
32_D11
32_D12
Z_PI
32_D13
32_D14
32TDI CE2
PWDA
Y_CE
96ADD1296ADD12
CN2001
AVD1
32_D15
GND/DRIVE-
LRCK
SDTI
SDTO
MCLK
SCLK
LRCK
Z_PTR_AD F/Z_VCC Z_LED
32_A07
32_A08
32_A09
32_A10
IRIS_O/C
32_A11
32_A12
32_A13
32_A14
F_OUT_D
HALL_A/D
H_OFFSET
H_GAIN
32_A15
32_A16
DATA5
REG_4.8V
32_A17
32_A18
32_A19
32_A20
REG_15.0V
CCD_OUT
REG_-7.5V
IRIS_PWM
32_A21
32_A22
32_A23
REG_-7.5V
32_A24
REG_3.0V
32_A25
GND
REG_4.8V
32_A26
ADD5
GND
32_A27
32_A28
SDTI
ADD4
32_A29
Z_LED Z_CNT Z_OUT_B
ADD3 CLK27 CLKDMA1 CLKDMA2 AVD1
32_A30
ADD2 ADD1 ADD0
DATA1
DATA15 DATA14 DATA13 CLK90SD2 CLKFCNV CLK18 CLKENC DATA12 DATA11 CLKFMC DATA10 DATA9 DATA8 CLKENC DATA7 CLK18 CLKFCNV CLK90SD2 CLK27 CLKDMA1 CLKDMA2 AVD1 AVD2 AHD1 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 ADD12 ADD1 ADD2 ADD3 ADD4 ADD5 ADD6 ADD7 ADD8 ADD9 ADD10 ADD11 SCK_0 SO_0 SI_0 M32R_CS
SDTO
GND
CN3003
HP_CTL
VOUT_CTL HP_CTL
MIC_IN MIC_GND
REG_3.3V
XSDRQ
32TCK
32TDO
32TMS
32nTRST
32TDI
AL3.3V
SO_8
SI_8 SO_8 SCK_8SCK_8
SCK_8
SO_8
SS_FCLE
SCK_0
SO_0 SI_0
M32R_CS
SS_FALE
SS_FEW SS_FWP SS_FD0 SS_FD1 SS_FD2 SS_FD3
SS_CD
SS_FD4 SS_FD5 SS_FD6 SS_FD7
SS_RB
SS_FRE
GND
SS_FCE
GND VCC
32DBI
GND
32RST
nTRST
DATA6 ADD11
DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 ADD0 ADD1 ADD2 ADD3 ADD4 ADD5 ADD6 ADD7 ADD8 ADD9 ADD10 ADD11
AM_ADRS0
MODE_C
KEY_A
AL_3.3V
LCD_CS
LCD_SI
RESET
REG_3.3V
REG_4.8V
GND
BYZZER
STO_FULL
STROB_AD
SENS_EVR
STO_FULL
STO_CHG
GATE_PULSE
GATE_PULSE SENS_EVR STO_CHG STROB_AD REG_3.3V GND REG_4.8V SLF_LED
SLF_LED
GND
STROB_AD
CHG_ON
STO_OFF
GATE_PULSE
STO_C
STO_E
REG_4.8V
CLK36CLK36
SHUTTER
FSL_R_A
FSL_R_B
Z_OUT_A
Z_OUT_B
Z_CNT
Z_LED
Z_PI
F_OUT_A
F_OUT_B
F_OUT_C
F_OUT_D
F_LED
F_PI
BT4000+
USB_+
USB_-
F_PI
JTAGMODE
135TCK 135TDO 135TMS 135TDI
SS_LVD
SENS.2
HDY
HDRY
HDBY
RESET
AHD2 FLD1 FLD2 HDENC VDENC
ID
VDTG
HDTG
ID
VDTG
HDTG
H_OFFSET
H_GAIN
PORT_102
Y_CE
PORT_102
CN1001
SSFDC
0
REG_4.8V REG_2.5V
1
GND GND GND
CLK36
GND
AUDIO
GND
FLASH
BL
JACK
L_DRV_SCLK
HVVDD MON_CS
BL_GND
VOUT_CTL
LITHIUM
D/A_YCOUT
GND
REG_-3.0V
MIC LCD
GND
DC_JACK
MODE_C
KEY_A
AL_3.3V
HVVDD
PWR_CTL
GND
Batt+
M_EVR
GND
VIDEO OUT
MONI
BATTERY
AL3.3V
M_SIG_GND
RPD
Batt-
STROBO
M_SIG_GND
M_PSIG
M_SIG_C
M_BL_ON
MON_CS
SCK_O
SO_0
REG_15.0V
REG_3.0V
GND
UNIT
GND
GND
SO_0
REG_15.0V
REG_3.0V
REG_3.3V
REG_-3.0V
GND
GND
SWITCH
*SIG_GND
WIDE
JCY0097-3
XE+
VST
DC/DC
UNREG
LCD_CS
HST
M_GREEN
REF Cext/Rext
M_BLUE
PRINTER
PSIG
GND
GREEN M_EVR RED BLUE COM VST
LCD_SI
LCD_SD
LCD_SCK
RESET
REG_3.3V
REG_4.8V
GND
REG_3.0V
REG_4.8V
ADO_3.0V REG_6.3V
REG_-7.5V REG_15.0V
B-Y
ADO_4.8V REG_4.8V
GND
UNREG
FSL_R- FSL_R+
R-Y
UNREG
Y VCK EN SIG_GND
AL3.3V
COM
JCY0135
GND
REG_6.3V
SWITCH
UNREG
GND
CTL
GND
M_COM
M_SIG_C
M_RED
SWITCH
ID
REG_3.3V
Batt+
Batt-
SLF_LED
GND
GND
USB
GND
GND
32nTRST
GND
REG_2.5V
32TMS
VCK
EN
DWN
HVVDD
SIG_GND
HVVDD
32TDO
32TDI
Y
R_Y
B_Y
32TCK
REG_15.0V
REG_15.0V
REG_4.8V
GND
REG_-7.5V
OPERATION
BATTERY
LIGHT
(SYSCON)
CLPDM
(DSP97) AL3.3V
(DSP146)
RPD
GND
NO NAME
01 MAIN
02 CCD
03 MONI REG
04 JACK
REG_4.8V
REG_4.8V
05 STROBE FLASH
5V IN
GND
SWITCH
VSSG
COM
MONITOR
WIDE
HST
REF
UNREG
TEST
Cext/Rext
HCK2
F/Z_MDA
3.0V
BACK
HCK1
A/V
PSIG
BUZZER
P.S.
CAMERA
UNIT
GREEN
GND
SIG_GND
CLE ALE #NAME? #NAME?
HDY
HDRY
HDBY
SCK_0
03 REG
GND
COM
VST
VCK
EN
DWN
02
04
05
32DBI
32RST
VSSG
WIDE
HST
REF
Cext/Rext
HCK2
HCK1
PSIG
GREEN
RED
BLUE
RGT
135TMS
JTAGMODE
RED
BLUE
RGT
N.C.
N.C.
135TDI
135TDO
XSDEN
XSDRQ
135nTRST
HP_CTL
SDI
SRCLK
GND
135TCK
STROBE_AD
BT4001+
CHG_ON
STO_OFF
USB_D+
GATE_PULSE
STO_C
STO_E
STROBE
XE-
TRG+
TRG-
SEN_C
SEN_E
F_PTR_AD
REG_4.8V
F_LED F/Z_VCC
HV
REG_4.8V
USB_D-
REG_4.8V
REG_4.8V
SO+
GND
GND
LCD_DRV_SO
SO-
TG_CS
REG_4.8V
VSUB_CNT
REG_-7.5V
GND
GND
CCD_OUT
REG_6.3V
M_BL_ON
BL_GND
BL_GND
BL_GND
PRIN_TX
SHP
PRIN_RX
JACK_CTL
ZOOM+ ZOOM- FOCUS4 FOCUS1 FOCUS2 FOCUS3
CCD
DRIVE+
GND/DRIVE-
HGOUT+ HGVSS- HGOUT- HGVCC+ DAMP- DAMP+ Z_PTR_AD F/Z_VCC Z_LED
STROBE
SHD
CHKUNREG
CHKUNREG PWR_CTL UNREG REG_3.3V UNREG REG_3.3V REG_3.0V REG_3.0V REG_3.3V REG_3.3V ADO_3.0V REG_-3.0V
JCY0146
CDS
AGC
A/D
REG_6.3V REG_6.3V REG_6.3V REG_6.3V REG_-7.5V REG_-7.5V REG_15.0V REG_15.0V ADO_4.8V ADO_4.8V REG_4.8V REG_4.8V
BtoB
REG_2.5V REG_2.5V REG_2.5V REG_4.8V GND GND GND GND GND GND GND GND GND GND GND M_BL_ON RPD
LCDJIG
M_SIG_C
M_SIG_GND
HCK1 HCK2 DWN HVVDD VSSG RGT
XRS
PBLK
OP
D0 D1
OBCLP
MAIN
SENS
LAMP
D2 D3
IRIS
GND #NAME? VCC D4 D5 D6 D7 LVD GND R/-B #NAME? #NAME? VCC SENS.1 SENS.2
HDTG
ADCLK
VDTG
GND
REG_3.0V
REG_3.0V
(Page 3-15)
(Page 3-12)
(Page 3-12)
(Page 3-12)
(Page 3-7)
(Page 3-11)
(Page 3-13) (Page 3-13)
(Page 3-9)
(Page 3-5)
(Page 3-16)
(Page 3-17)
(Page 3-14)
NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only.
When replacing the parts, refer to the Parts List.

3.2 MAIN (SYSCON) SCHEMATIC DIAGRAM
3-5 3-6
IC4001
R4036
C4013 C4012
IC4005
X4003
MAINCLK
JACK_CTL
TP4004
IC4001
135TDO
135TCK
BT4001+
SDA10
135TMS
135TDI
135nTRST
JTAGMODE
TP4005
FLD1
PORT_04
CE
R4038
SDWE
IC4015
USB_D+
USB_D-
R4078
R4079
R4080
R4009
PORT_02
SDCS
SDCKE
X4004
SDCLK
D4004
REG_4.8V
135_RX
IC4103
135_TX
R4002
WTH
A_WTL
R4003
R4051
Q4005
R4005
AVD1
CDS_CS
R4006
TG_CS
Z_PI
R4007
L4001
C4022
96TDO
D4005
R4092
TCK
R4034
TMS
TRST
DSEL_0
R4008
LCD_DRV_SO
LCD_DRV_SCLK
ADD0
PORT_05
TP4001
IC4101
IC4102
R4037
AL3.3V
CHKUNREG
PWR_CTL
R4021
D4002
R4024
Q4002
SLF_LED
R4022
AHD1
PWDA
Q4003
R4060
CN4001
SHUTTER
R4058
Q4004
Q4001
R4105
R4001
IC4012
PWAD
C4104
MON_CS
IC4007
M_EVR
SENS_EVR
R4059
H_OFFSET
H_GAIN
C4016
R4064
R4065
R4066
PORT_102
R4188
C4028
R4107
C4017 R4057
RESET
R4185
R4067
C4003
R4027
IC4008
R4061
REG_3.3V
GND
C4018
R4069
R4063
R4062
R4023
R4055
D4101
X4002
R4044
Q4006
R4085
R4101
97TDI
R4045
R4004
R4071
R4102
C4021
Z_CNT
R4035
C4006 C4007
C4015
C4011
C4001
C4002
STO_FULL
STO_CHG DATA0
FLS_RST
GATE_PULSE
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA9
DATA8
DATA10
DATA11
STROB_AD
DATA12
DATA13
DATA14
DATA15
ADD2
ADD3
ADD4
ADD5
ADD6
ADD7
ADD8
WE
ADD9
ADD10
ADD11
ADD12
ADD13
ADD14
ADD15
ADD16
ADD17
ADD18
ADD19
ADD20
RAS
CAS
OE
ADD1
Z_LED
IRIS_O/C
FSL_R_A
F_OUT_A
F_OUT_B
F_OUT_C
F_OUT_D
F_PI
R4082
UDQM
R4056
R4010
R4011
R4031 R4030
SCK_0
SO_0
SI_0
R4029
R4028
LDQM
R4026
R4025
R4050
R4049
R4048
R4047
R4046
R4012
R4013
R4014
R4016
R4017
R4018
R4019
R4020
FSL_R_B
Z_OUT_A
Z_OUT_B
F_LED
HOLE_AD
M32R_CS
HP_CTL
VOUT_CTL
R4052
R4083
R4084
R4108
R4104
R4184
C4027
SS_LVD
IC4104
R4103
IC4012
R4076
R4075
L4002
INT3
R4072
C4102
C4101
R4081
R4039
R4040
R4041
R4042
R4043
AM_ADRS0
R4032
R4095
R4015
R4096
C4105
R4106
C4103
IC4107
IC4106
IC4105
R4097
R4098
R4099
R4100
R4074 R4073
R4068
R4070
R4093
R4094
R4089
R4090
R4091
IC4009
SCK_8
SO_8
SI_8
C4029 C4030
R4086
R4087
L4003
UNREG
IC4109
2.2K
0.01 10p
0Ω
22
22
1.5k
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0.01
0Ω
0Ω
0Ω
100K
10K
2.2k
10K
5.6k
10k
0Ω
10k
82k
0.01
10k
10k
10k
47k
0.1
0Ω
0.1 100k
0Ω
0Ω
10/
47k 0.01
330
1K
10K
10K
47k
1K
0Ω
0Ω
10k
10k
10/
1M
0.01
0.01
0.01
0.01
1M
10k
0Ω
10K
10k 10k 10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
270
10k
10k
10k
10k
10k
47k
22
22
0Ω
100k
0.047
100k
10K
10K
0.1
0.1
10K
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
1M
0.01
0Ω
0Ω 0Ω
0Ω
0Ω
0.1 10/
0Ω
10µ
VDD VDD VDD
VDD
VDD
VDD
VDD VDD
VDD
VDD
GND GND
GND
GND
GND
GND GND
GND
VSS
VSS
VSS
A7 A6 A5 A4 A3 A2 A1 A0 X32KIN X32KOUT X32MIN X32MOUT
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
DSEL0
INT3
INT2
INT1
INT0
P025
P024
P023
P022
P017
P016
P015
P014
P013
P012
P011
P010
P009
P008
P007
P006
P005
P004
P003
P002
P001
P000
FWEB FCEB FOEB LDQM UDQM SDWE
CAS RAS
SDCS
SDCLK SDCKE
CTS
DSR
DCD
SIRIN
SIROUT
FG1 FG2
CD
USB_SUSPEND
P100
TESTENB
TESTWRB
TESTCLKB
TREQB
JTAGMODE
NC
PO20
PO19
PO18
P102 P103 P104 P105 SCK8
SOCK8
SO8 SI8
PO31 PO30 PO29
SICK16
SO16
VDD A31 A30 A29 A28 A27 A26 A25 A24
Rx_vpi
Rx_vmi
Rx_data
Tx_oe_n
Tx_vpo
Tx_vmo
USBCLK
PWM
A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8
D0
DSEL1
RESET
TXD
RXD
TBE
TCK
TMS
TDI
TDO
nTRST
TREQA
TACK
SDA10
BUZZER
MAIN_CLK_OUT
ZOOM
HALL
AN6
STORB_AD
PO21
P101
P106
SOCK16
SI16
AN0
AN1
P_STB
GND DIR
P_WRITE
P027 P026 AVDD VREF
VSS(AGND)
AVDD
BATT
F_PI
AN7
AGND
GND
NC EXT8 VSS EXT10 EXT6 EXT11 EXT9 GND
VDD
GND
VDD
GND
EXT7
EXT5
EXT2
JCY0135
Xout
INTRVSS
VDD
SIO
CLK
CS Xin
RS5C314-X
NAX0399-001X
SDA13
GND VDD
EXT4 EXT1 SDA12 VDD GND VDD
EXT3 EXT0
SDA11
VDD
VCC3 TEST1 TEST2 XIN XOUT CS RD WR RESET D+ D-
INTR
D15
D14
D13
D12
GND
VCC5
D11
D10
D9
ALE
ADSEL
A7 A6 A5 A4 A3 A2 A1 A0
DACK
DREQ
AD7
AD6
AD5
AD4
GND
VCC5
AD3
AD2
AD1
AD0
D8
NC NC NC
NC
NC
NC
NC NC NC
NC
NC
NC
ML60851CLB
NAX0398-001X
TLGU1002/KL/-X
TC7W32FK-X
DTA114EE-X
NQR0129-002X
MA716-X
VCC
N.C GND
OUT
IC-PST9327U-X
VCC
GNDN.C
OUT
S-80824ANNP-W
TLSU1002/LM/-X
DTA114EE-X
2SA1774/RS/-X
BUZZER
GND
REG_4.8V
REG_3.3V
RESET
LCD_SCK
LCD_SO
LCD_SI
LCD_CS
AL_3.3V
KEY_A
MODE_C
RN1104FT-X
DTA114EE-X
Ao7
Ao6
Ao5
Ao4
Ao3
Ao2
Vss
Vcc
Ao8
Do
LD
CLK
DI
Ao1
GND
Vdd
M62367GP-X
6.3V
IC-PST9327U-X
MA704-X
NAX0390-001X
2SB970/QRS/-X
2SB710/R/-X
6.3V
T
TC7W08FK-X
VDD
VSS TC7S08FU-X
NQR0129-002X
Q GND
VCC
PR
CLR
Q
CK D TC7W74FK-X TC7W08FK-X TC7W04FK-X
S-814A30AMC-W
10V
T
TCS66FU-X
OPEN
OPEN
32KHz
OPEN
OPEN
OPEN
OPEN
48MHz
RTC
32MHz
32kHz
STROBE LED
FOCUS LED
OUT VDD
NCVSS
OPEN
OPEN
SYSCON
OPEN OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPENOPEN
0 1 MAIN (SYSCON)
TO
ARM ROM
TO
ARM ROM
TO
DSP146
TO
CDS AGC A/D
TO
CAMERA
OPERATION
TO
CDS AGC A/D
TO
DSP 97
TO
STROBE
TO
DSP146
TO
F/Z_MDA
TO
DC/DC
TO
DSP146
TO
STROBE
TO
F/Z_MDA
TO
DSP97
TO
DSP97
TO
DSP146, DSP97, ARM ROM
TO
DSP97
TO
CDS AGC A/D
TO
DSP97 TO
AUDIO
!
!
!
NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only.
When replacing the parts, refer to the Parts List.

3.3 MAIN (DSP146) SCHEMATIC DIAGRAM
3-7 3-8
IC3001
IC3501
CN3003
IC3502
IC3503
A/D0
A/D1
A/D2
A/D3
A/D4
A/D5
A/D6
A/D7
A/D8
A/D9
32_A30
X3001
R3003
HDTG
VDTG
CLK36
GND
TRST
TCK
TMS
97TDO
96TDO
R3001
R3002
PORT_05
RESET
ADD0
C3052
Q3004
Q3001 Q3002
R3047
R3045
R3042
C3032
R3043
R3044
C3033
R3046
Q3003
R3060
R3053
R3055 R3056
R3054
R3057
R3052
R3050
R3049
C3014
IC3001
C3034
C3035
C3036
C3037
C3038
C3039
C3040
C3041
L3503
SDTO
IC3504
R3503
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
ADD1
ADD2
ADD3
ADD4
ADD5
ADD6
ADD7
ADD8
ADD9
ADD10
ADD11
96ADD12
R3073 R3074 R3115 R3116
R3072
32_D01
32_D02
32_D03
32_D04
32_D05
32_D06
32_D00
32_D07
32_D08
32_D09
32_D10
32_D11
32_D12
32_D13
32_D14
32_D15
32_A07
32_A08
32_A09
32_A10
32_A11
32_A12
32_A13
32_A14
32_A15
32_A16
32_A17
32_A18
32_A19
32_A20
32_A21
32_A22
32_A23
32_A24
32_A25
32_A26
32_A27
32_A28
32_A29
CE2
F_WE
A_WTL
Y_CE
WTH
CLKDMA2
CLKFMC
CLKENC
CLKFCNV
CLKDMA1
CLK18
CLK90SD2
CLK27
R3119
R3120 R3121 R3122 R3123 R3124 R3125 R3126 R3127 R3128 R3129
R3131
DMACO7
DMACO6
DMACO5
DMACO4
DMACO3
DMACO2
DMACO1
DMACO0
DMAYO7
DMAYO6
DMAYO5
DMAYO4
DMAYO3
DMAYO2
DMAYO1
DMAYO0
DMAIRB7
DMAIRB6
DMAIRB5
DMAIRB4
DMAIRB3
DMAIRB2
DMAIRB1
DMAIRB0
DMAIY7
DMAIY6
DMAIY5
DMAIY4
DMAIY3
DMAIY2
DMAIY1
DMAIY0
AHD1
AHD2
AVD1
AVD2
FLD1
FLD2
HDENC
VDENC
R3207 R3206
R3205
R3204
R3203
R3202
R3201
R3200
R3199
R3198
L3507
L3506
L3505
SDTI
LRCK
SCLK
C3504
C3511
MCLK
ADO_3.0V
ADO_4.8V
REG_-3.0V
R3048
R3058
C3518
R3059
R3051
C3053
C3051
C3050
C3048
L3501
L3502
C3503
GND
GND
R3117
C3525
C3047
C3049
R3118
C3031
R3183
TL3009
HDY
HDBY
HDRY
L3504
TL3015
TL3510
R3176
R3177
R3178
TL3001
TL3002
R3182
R3181
R3180
C3002
ID
IRIS_PWM
RESET
C3003 C3004 C3005 C3006 C3007 C3008 C3009 C3010 C3011 C3012 C3013
C3015 C3016 C3017 C3018 C3019 C3020 C3021 C3022 C3024 C3027
R3249 R3250
C3030
R3272 R3273
TL3017
C3023
C3025
L3001
CN3001
C3501
C3502
C3001
C3026
CN3001
CN3001
X3002
C3028
CLK32
CHKUNREG
PWR_CTL
UNREG
REG_3.3V
REG_3.0V
C3529
REG_6.3V
REG_-7.5V
REG_15.0V
C3530
REG_4.8V
REG_2.5V
CN3002
L3002 C3029
R3295
MON_CS
LCD_DRV_SCLK
LCD_DRV_SO
M_EVR
R-Y
B-Y
Y
M_BL_ON
RPD
M_BLUE
M_RED
M_GREEN
M_PSIG
M_SIG_C
M_SIG_GND
M_COM
R3296 R3297
R3504
R3505
R3506
R3507
R3508
4_8L5507
SS_LVD
PORT_05
R3184
R3023
R3008R3009R3010R3011R3012R3013R3014
R3007
R3015R3016R3017R3018R3019R3020R3021R3022
C3045
L3003 C3043
L3004
C3042
C3044
MAINCLK
AM_ADRS0
R3024
R3025
R3078
R3077
C3528
C3527
C3526
R3076
R3061
IC3002
R3114
0Ω
0Ω
0Ω
0Ω
10k
0.1
10k
10k
0.1
1.2k
0Ω
470
470
0Ω
0Ω
1.2k
2.7k
4.7k
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
47k
0Ω 0Ω 0Ω 0Ω
0Ω
22
22 68 68 0Ω 68 68 68 68 22 22 0Ω 0Ω 0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
0.1
0.1
470
0Ω
0.1
1.2k
0Ω
10 0.1
1
0Ω
0.1
0Ω
100
100
100
0Ω
0.1
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1
15k 12k
0.1
12k 12k
0.1
0.1
10
0.1
0.1
10
0.1
0.1
0.1
10
2.7k 2.7k 10k
0Ω
0Ω
0Ω
0Ω
0Ω
0Ω
10k
10k 10k 10k 10k 10k 3.3k 10k
10k
10k 10k 10k 10k 10k 10k 10k 10k
100p
10µ
10µ
47k
100
0Ω
0Ω
0.1
10
10
0Ω
0Ω
CCDI0
CCDI1 CCDI2 CCDI3 CCDI4 CCDI5 CCDI6 CCDI7 CCDI8 CCDI9
AHD1
AHD2
AVD1
AVD2
FLD1
FLD2
HDENC
VDENC
HDY
HDRY
HDBY
LS_DQ0
LS_DQ1
LS_DQ2
LS_DQ3
LS_DQ4
LS_DQ5
LS_DQ6
LS_DQ7
LS_ADR0
LS_ADR1
LS_ADR2
LS_ADR3
LS_ADR4
LS_ADR5
LS_ADR6
LS_ADR7
LS_ADR8
LS_ADR9
LS_ADR10
LS_ADR11
LS_ADR12
LS_ADR13
LS_DQ8
LS_DQ9
LS_DQ10
LS_DQ11
LS_DQ12
LS_DQ13
LS_DQ14
LS_DQ15
LS_CKE0
LS_CKE1
LS_CKE2
LS_CS0
LS_CS1
LS_CS2
LS_LDQM
LS_UDQM
LS_RAS
LS_CAS
LS_WE
AM_DATA0
AM_DATA1
AM_DATA2
AM_DATA3
AM_DATA4
AM_DATA5
AM_DATA6
AM_DATA7
AM_DATA8
AM_DATA9
AM_DATA10
AM_DATA11
AM_DATA12
AM_DATA13
AM_DATA14
AM_DATA15
AM_ADRS0
AM_ADRS1
AM_ADRS2
AM_ADRS3
AM_ADRS4
AM_ADRS5
AM_ADRS6
AM_ADRS7
AM_ADRS8
AM_ADRS9
AM_ADRS10
AM_ADRS11
AM_ADRS12
AM_CS
AM_WTH AM_WTL MR_DATA0 MR_DATA1 MR_DATA2 MR_DATA3 MR_DATA4 MR_DATA5 MR_DATA6 MR_DATA7 MR_DATA8 MR_DATA9 MR_DATA10 MR_DATA11 MR_DATA12 MR_DATA13 MR_DATA14 MR_DATA15 MR_CS MR_WE
CLKDMA2 CLKFMC CLKENC CLKFCNV CLKDMA1 CLK18 CLK90SD2
CLK36 CLK27 CLKAUD
CLK32
CLK54
DMAYO0
DMAYO1
DMAYO2
DMAYO3
DMAYO4
DMAYO5
DMAYO6
DMAYO7
DMACO0
DMACO1
DMACO2
DMACO3
DMACO4
DMACO5
DMACO6
DMACO7
DMAYDT0
DMAYDT1
DMAYDT2
DMAYDT3
DMAYDT4
DMAYDT5
DMAYDT6
DMAYDT7
DMACDT0
DMACDT1
DMACDT2
DMACDT3
DMACDT4
DMACDT5
DMACDT6
DMACDT7
SS_FD0 SS_FD1 SS_FD2 SS_FD3 SS_FD4 SS_FD5 SS_FD6 SS_FD7 SS_PSD
SS_CD SS_RB
SS_FWP
SS_FCLE SS_FALE
SS_FRE SS_FEW
SS_WAIT
IRIS_A
JPEG_IREQ
AUD_SDTO
AUD_SDTI
AUD_LRCK
AUD_SCLK
GND
KOUT
HDCCD
VDCCD
FLDCCD
MCLR
GND GND GND GND GND GND GND GND
VDDH VDDH
GND
VDDH
GND GND GND GND GND
VDDH VDDH VDDH VDDH VDDH
TRST
TCK
TMS
TDI
TDO
VDDL VDDL VDDL VDDL VDDL VDDL VDDL VDDL VDDL VDDL VDDL
VREF_HDY
VREF_HDRY
AVSS_HDRB ADVV_HDRB
AVSS_HDY AVDD_HDY
AVSSK AVDDK
CLK90gat
SS_V3X5
VRNK
VRO_RY
VRO_Y
VRPK
MR_ADRS7 MR_ADRS8 MR_ADRS9 MR_ADRS10 MR_ADRS11 MR_ADRS12 MR_ADRS13 MR_ADRS14 MR_ADRS15 MR_ADRS16 MR_ADRS17 MR_ADRS18 MR_ADRS19 MR_ADRS20 MR_ADRS21 MR_ADRS22 MR_ADRS23 MR_ADRS24 MR_ADRS25 MR_ADRS26 MR_ADRS27 MR_ADRS28 MR_ADRS29 MR_ADRS30
SS_FCE0
PLLVDD1
PLLVDD2
PLLVDD3
PLLVSS1
PLLVSS2
PLLVSS3
NC
OVDD3X
OVSSX OVSSX OVSSX OVSSX OVSSX
NC
OVDD3X
OVDD3X
OVDD3X
OVDD3X
OVDD3X
OVDD3X
OVDD3X
OVDD3X PLL_TEST VPD
DTEST PLL_RST
JCY0146
VDD VDD VDD DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8
DQ9
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
VDDQ VDDQ
VDDQ VDDQVSSQ
VSSQ
VSSQ VSSQ
LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 A4
A5 A6 A7 A8 A9
A11
NC
CKE CLK
UDQM
NC/RFU
VSS VSS VSS
GND
GND
GND
CLE
ALE
-WE
-WP
D0
D1
D2
D3
-CD
VCC
D4
D5
D6
D7
LVD
R/-B
-RE
-CE
VCC
SENS.1
SENS.2
VDD VDD VDD DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8
DQ9
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
VDDQ VDDQ
VDDQ VDDQVSSQ
VSSQ
VSSQ VSSQ
LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 A4
A5 A6 A7 A8 A9
A11
NC
CKE CLK
UDQM
NC/RFU
VSS VSS VSS
VDD VDD VDD DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 DQ8
DQ9
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
VDDQ VDDQ
VDDQ VDDQVSSQ
VSSQ
VSSQ VSSQ
LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 A4
A5 A6 A7 A8 A9
A11
NC
CKE CLK
UDQM
NC/RFU
VSS VSS VSS
NC
GNDOUT
VDD
NAX0302-001X
NAX0303-001X
NAX0305-001X
2SC4617/QR/-X
HN1C01FU/YG/-X HN1C01FU/YG/-X
HN1C01FU/YG/-X
NC NC NC NC NC
NC NC NC NC NC NC NC
NC NC
NC
NQR0154-001X
NC
IN
GNDOUT
Vcc
TC7SH04FU-X
NQR0251-001X
NQR0251-001X
NQR0154-001X
NQR0129-002X
/6.3
T
NQR0154-001X
NQR0129-002X
CHKUNREG
PWR_CTL
UNREG
UNREG
REG_3.3V
REG_3.3V
REG_3.0V
REG_3.0V
REG_3.3V
REG_3.3V
ADO_3.0V
REG_-3.0V
REG_-7.5V
REG_-7.5V
REG_15.0V
REG_15.0V
REG_4.8V
REG_4.8V
REG_4.8V
REG_6.3V
REG_6.3V
REG_6.3V
REG_6.3V
ADO_4.8V
ADO_4.8V
REG_2.5V
REG_2.5V
REG_2.5V
REG_4.8V
REG_2.5V
/6.3
T
/6.3
T
GND
GND
GND
R-Y
GND
GND
Y
M_BL_ON
M_SIG_C
VST
GND
GND
GND
M_EVR
GND
B-Y
GND
GND
RPD
M_SIG_GND
COM
VCK
MON_CS
LCD_DRV_SCLK
LCD_DRV_SO
GND
GND
GND
GND
GND
GND
GND
EN
HCK1
DWN
HST
Cext/Rext
GREEN
BLUE
SIG_GND
SIG_GND
VSSG
WIDE
REF
PSIG
RED
RGT
HVVDD
HCK2
HVVDD
NC
GNDOUT
VDD
NAX0391-001X
N.C.
RGT
BLUE
RED
GREEN
PSIG
HCK1
HCK2
Cext/Rext
TEST
REF
HST
WIDE
VSSG
SIG_GND
DWN
EN
VCK
VST
COM
N.C.
COM
HVVDD
HVVDD
NQR0154-001X
/6.3
T
NQR0129-002X
/6.3
T
NQR0129-002X
/6.3
T
/6.3
T
/6.3
T
74AHC1G08GW-X
64M_SDRAM
64M_SDRAM
64M_SDRAM
SSFDC_JACK
ADO_3.0V
BL_GND
ADO_4.8V
OPEN
REG_2.5V
REG_3.3V
0 1 MAIN
OPEN
GND
OPEN
OPEN
OPEN
CAMERA DSP
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
SSFDC
SDRAM CONTROL
LINE MEMORY CONTROLLER
JPEG PROCESS
HD DAC
(DSP146)
TO
DSP97
TO
AUDIO
TO
CDS AGC A/D
TO
DSP97
TO
IRIS
TO
CDS AGC A/D
TO DSP146
TO CDS AGC A/D
TO
DSP97
TO SYSCON
TO
DSP97
TO
DSP97
TO
SYCON, DSP97
TO
SYCON
TO
MONI REG.
TO
LCD
TO
SYSCON
TO
DSP97
TO
JACK
TO
CDS AGC A/D
JIG CN.
NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only.
When replacing the parts, refer to the Parts List.

3.4 MAIN (DSP97) SCHEMATIC DIAGRAM
3-9 3-10
CN5501
R-Y USB_D-
IC5503
TP5007
REG_4.8V HDY HDRY HDBY
C5576
C5575
REG_3.0V
RA5029
REG_3.3V
C5506
TP5501
TP5504
R5521
R5510
L5003
C5005 C5006
C5501
C5516
REG_-3.0V
L5505
C5519
TP5008 TP5009
TMS
32TDI
32TCK
32TMS
32nTRST
REG_2.5V
C5512
JACK_CTL
C5505
C5502
C5511
C5518
C5513 C5514
R5539
TP5001
R5502
USB_D+ BT4001+ 135_RX 135_TX
R5515
R5097
R5009
REG_6.3V
R5158
GND B-Y
IC5001
Y
TP5508
C5016
R5528
R5013
IC5001
IC5002
GND
C5001
C5002
C5007
L5005
32TDO
SCK_8
SO_8
R5160
R5533
R5010
R5534
R5012
L5004
C5021
C5568
Q5503
R5535
Q5502
R5531
DMAYO0
M_BL_ON
TP5505
C5022
R5530
RA5028RA5027
R5007
C5017
R5532
RA5026 RA5025RA5024
R5008
WTH
A_WTL
32DBI
L5506
C5542
R5092
C5567
R5018
IC5001
IC5004
R5015
IC5003
PORT_04
R5016
ADD13
IC5501
SI_8
C5543 C5545
C5544
DSEL_0
C5023
A_CS
Y_CE
R5019 R5020
R5042
R5053
R5054
R5055
R5056
INT3
Q5504
Q5501
97TDO
R5526
R5529
ADD12
C5572
IC5006 IC5007 IC5008
R5061
R5060
R5062
PORT_102
C5546
C5547
C5548
R5096
C5549
F_WE
SCK_0
96ADD12
R5063
R5064
R5537
R5065
R5538
R5066
R5541
R5542
R5544
R5540
R5543
R5268
C5550
C5551
C5552
C5553
R5051 R5052
R5048
R5047
TRST
R5046
R5049 R5050
R5044
R5501
R5094
R5095
R5155 R5154
TP5502
TP5503
R5506
L5001
L5502
L5501
C5515
C5520
C5522
C5523
C5517
C5535C5533 C5534C5532
C5531
C5524
C5526
C5525
C5521
C5527
C5528
C5529
C5530
C5537
C5539
C5536
C5538
C5540
R5514
R5513
R5517
L5002 C5003 C5004 R5001
R5002
R5004
R5003 R5005
R5006
C5013
C5014 C5015
C5541
C5554
R5524
C5566
C5555
TP5518
L5503
DMAYO1
DMAYO2
R5014
R5017
C5556
C5557
C5558 C5559 C5560
TP5516 TP5515
C5561
C5562 C5563
C5564
A_CS
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
ADD1
ADD2
ADD3
ADD4
ADD5
ADD6
ADD7
ADD8
ADD9
ADD10
ADD11
RESET
CLKFMC
CLKENC
CLK18
CLKFCNV
CLK90SD2
CLK27
AHD1
AVD1
CE2
CLKDMA1
AHD2
R5520
CLKDMA2
DATA3
DATA2
DATA1
DATA0
L5504
DMAYO3
DMAYO4
DMAYO5
DMAYO6
DMAYO7
DMACO0
DMACO1
DMACO2
DMACO3
DMACO4
DMACO5
DMACO6
DMACO7
R5040
R5041
R5523
R5527
R5525
C5571
AVD2
FLD1
TP5520 TP5521
TP5003 TP5004 TP5005 TP5006
M32R_CS
SO_0
SI_0
FLD2
CLK32
32_D06
DMAIRB7
DMAIRB6
DMAIRB5
DMAIRB4
DMAIRB3
DMAIRB2
DMAIRB1
DMAIRB0
DMAIY7
DMAIY6
DMAIY5
DMAIY4
DMAIY3
DMAIY2
DMAIY1
DMAIY0
32_D07 32_D08 32_D09 32_D10 32_D11 32_D12 32_D13 32_D14 32_D15 32_A30 32_A07 32_A08 32_A09 32_A10 32_A11 32_D03 32_D04 32_D05 32_D00 32_D01 32_D02 32_A12 32_A13 32_A14 32_A15 32_A16 32_A17 32_A18 32_A19 32_A20 32_A21 32_A22 32_A23 32_A24 32_A25 32_A26 32_A27 32_A28 32_A29
R5159
L5507
C5573
C5574
TCK
HP_CTL
R5504
R5098
VOUT_CTL
R5067
FLS_RST
4_8L5507
97TDI
HDENC
IC5005
VDENC
IC5504
M32R_CS
SI_8
PORT_05
R5548
TL5501
TL5502
R5546
C5503
R5503
R5547
32RST
R5522
32RST
R5550
R5549
Q5505
C5577
R5516
R5511
REG_6.3V
R5512
C5569
IC5009
C5570
0.1
0.1
0Ω
0.1
0Ω
47k
10 0.1
10
0.1
0.1
0.1
0.1
0.1
10
10
0.1 10
0Ω
56k
0Ω
0Ω
1KΩ
0Ω
0.1
100
0Ω
10
0.1
0.1
0Ω
47
0Ω
100
0Ω
10
2.2k
130
0.1
13
0Ω0Ω
0Ω
0.1
2.2k
0Ω0Ω0Ω
0Ω
10
0Ω
2.7KΩ
0Ω
0Ω
0.1 0.1
0.1
0.1
2.7KΩ 2.7KΩ
1KΩ
0Ω
0Ω
0Ω
0Ω
3.9k
4.7k
1
0Ω
0.1
0.1
0.1
0Ω
0.1
47k
0Ω
0Ω
0Ω
47k
0Ω
0Ω
0Ω
0.1
0.1
0.1
0.1
0Ω56k
56k
0Ω56k 0Ω56k 0Ω
47k
0Ω
0Ω
0Ω 0Ω
0Ω
10
0.01
0.01
0.01
0.1
0.010.01 0.010.010.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0.01
0Ω
0Ω
47k
0Ω10 0.1 12k
10k
12k
15k 15k
12k
0.1
0.1 0.1
0.1
0.1
680
82p
0.1
0Ω 0Ω
0.1
0.1
0.1 0.1
0.1 0.1 0.1 0.1
0.1
56k
0Ω
0Ω
470
0Ω
1.2k
18p
4.7k
10
0.1
0Ω
0Ω
0Ω
10p 10k
0Ω
1
1k
0Ω
HP_1 VOUT_CTL REG_3.0V REG_3.0V D/A_YCOUT REG_-3.0V JACK_CTL HDBY HDRY HDY REG_4.8V REG_4.8V REG_4.8V GND GND GND GND GND PRIN_RX SDI PRIN_TX SRCLK XSDEN XSDRQ BL_GND BL_GND BL_GND M_BL_ON REG_6.3V REG_6.3V USB_D+ USB_D- BT4001+ HP_CTL
A3
A4
A2
A1
A0
CE
OE
VSS
A7
A17
A6
A5
DQ0 DQ8 DQ9 DQ1
RY/BY
NC
A18
NC
DQ2
DQ10 DQ11
DQ3
WE
RESET
NC
A19 DQ5
DQ12
VCC
DQ4
A9 A8 A10 A11
DQ7
DQ14
DQ13
DQ6
A13 A12 A14 A15 A16
BYTE
DQ15/A-1
VSS MBV400TC90PBM02
NQR0129-002X
/6.3
T
QEE60JM-106
/6.3 T
NQR0129-002X
/6.3 T
/6.3
T
VCCX(3.3V) VCCX(3.3V) VCCX(3.3V) VCCX(3.3V) GND GND GND NC NC NC NC NC NC NC NC
NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC
/6.3
T
TVDD3 TVSS2
TVSS1 TVDD4
S_A0 S_A1 S_A2 S_A3 S_A4 S_A5 S_A6 S_A7 S_A8 S_A9
S_A10 S_A11 S_DQ0 S_DQ1 S_DQ2 S_DQ3 S_DQ4 S_DQ5 S_DQ6 S_DQ7 S_DQ8 S_DQ9
S_DQ10 S_DQ11
S_CLK S_CKE
S_CS S_WE
S_RAS S_CAS
S_DQML S_DQMU
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26 A27
A28
A29
BC2/A30
BC1
BC0
BS
RW
DC
HREQ
HACK
CS
CE1
CE0
CE2
WE
OE
BURST
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23 D24
D25 D26 D27 D28 D29 D30 D31
DMAIY0
DMAIY1
DMAIY2
DMAIY3
DMAIY4
DMAIY5
DMAIY6
DMAIY7
DMAIRB0
DMAIRB1
DMAIRB2
DMAIRB3
DMAIRB4
DMAIRB5
DMAIRB6
DMAIRB7
DMAYO0/COMIO0
DMAYO1/COMIO1
DMAYO2/COMIO2
DMAYO3/COMIO3
DMAYO4/COMIO4
DMAYO5/COMIO5
DMAYO6/COMIO6
DMAYO7/COMIO7
DMACO0/COMIO8
DMACO1/COMIO9
DMACO2/COMIO10
DMACO3/COMIO11
DMACO4/COMIO12
DMACO5/COMIO13
DMACO6/COMIO14
DMACO7/COMIO15
M32R_RST
CLR
XIN
XOUT
SCLK
SID
EMSZ_32
DREQ INT1 INT2 INT3 INT
TRST TCK TMS TDI TDO
VREFY
R-Y B-Y
VREFC
VREFRB
Y C
TXD1 RXD1 TXD2 RXD2
PORT0/COMIO16 PORT1/COMIO17 PORT2/COMIO18 PORT3/COMIO19 PORT4/COMIO20
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
ADR12
ADR1
ADR2
ADR3
ADR4
ADR5
ADR6
ADR7
ADR8
ADR9
ADR10
ADR11
CLK13
A_CS
WTH
A_WTL
CLKFMC CLKENC CLK18 CLKFCNV CLK90SD2 CLK27 AHD1 AVD1 FLD1 CLKDMA1 AHD2 AVD2 FLD2 CLKDMA2 SI_0 SO_0 SCLK_0 SI_1 SO_1 SCLK_1
SDTI/COMIO27 SDTO/COMIO28 MCLK/COMIO29 AUD_SCLK/COMIO30 LRCK/COMIO31
HDENC VDENC
PDATA DCLK ENA
VDDH
VDDH
VDDH
VDDH VDDH VDDH
VDDH VDDH
VSS VSS
VSS VSS
VSS
VSS
TVSS0 VSS VSS VSS
VSS VSS VSS VSS VSS VSS VSS VSS
VSS VSS
DVDDM
VDDL VDDL VDDL
VDDL VDDL VDDL VDDL VDDL VDDL VDDL
VDDL
TVDD6 AVDDV AVSSV TVDD5
IREFC
IREFRB
IREFY
DVDDM
TVDD0
TVSS4
TVDD1 TVDD2
TVSS3
JCY0097-3
VCC VCC DQ1 VSSQ VSSQ VSSQ
VSSQ
DQ2 DQ3 VCCQ VCCQ VCCQ
VCCQ
DQ4 DQ5 DQ6 DQ7 LDQM WE CAS RAS CS A10 A0 A1 A2 A3 VSS
VSS
A4 A5 A6 A7 A8 A9
NC CKE CLK
UDQM
A11 DQ8 DQ9
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15DQ16
MSM56V16160D1LS
/6.3
T
NQR0251-001X
/6.3 T
2SA1774/RS/-X 2SA1774/RS/-X
NQR0129-002X
/6.3
T
NC NC NC NC NC NC NC NC
NC NC NC NC NC NC NC NC
TC7W08FU-X
TC7SHU04FU-X
M32Rx/D
VCC[2.5V] D23 VCC[2.5V] VCC[2.5V]
VCC[2.5V]
VCC[2.5V]
VCC[2.5V]
VCC[2.5V] VCC[2.5V]
VCC[2.5V]
VCC[2.5V]
VCC[2.5V]
VCC[2.5V] VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS VSS VSS VSS VSS VSS
VSS VSS VSS VSS VSS
DRAM3.3V
VCCX(3.3V)
DRAM3.3V
VCCX(3.3V)
VCCX(3.3V)
VCCX(3.3V)
VCCX(3.3V) VCCX(3.3V) VCCX(3.3V) VCCX(3.3V)
VCCX(3.3V) VCCX(3.3V)
VCCX
VCCX
DBI
VCCX
VCCX
D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D09 D08 D07 D06 D05 D04 D03 D02 D01 D00
VSS
STBY
WKUP
RST
CLKIN
PLLCNT1
PLLCNT2
TRST
TCK
SBI
INT
R/W
CS
HACK
HREQ
EMSZ
DC
RDY
BURST
BS
PP0
PP1
ST
PLLVCC
BC3 BC1 BC0
BC2/A30
PLLVSS
A29 A28 A27 A26 A25 A24 A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10
A09
A08
A06
A05
SID
A07
M/S
ROMSZ
TDI
TMS
TDO
D31
D30
D29
D28
D27
D26
D25
D24
M32310D5WG
HN1C01FU-X
2SC4617/QR/-X
TC7S66FU-X TC7S66FU-X TC7S04FU-X
NQR0154-001X
NQR0129-002X
NQR0129-002X
/6.3
/6.3
T
NQR0129-002X
NQR0129-002X
/6.3
TTC7S66FU-X
TC7S08FU-X
2SC4617/QR/-X
TC7S08FU-X
OPEN
SDRAM
M32Rx/D INTERFACE
OPEN
GND
REG_3.3V
Flash_CSP
BL_GND
OPEN
OPEN
OPEN
OPEN
OPEN
SDTO SCLK ASCK LRCK
TO_JCY0096
REG_2.5V
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
OPEN
GND
01 MAIN (DSP97)
TO
DSP146
TO
DSP146
TO
SYSCON
TO
DSP146
TO
CDS AGC A/D
TO
DSP146 TO SYSCON
TO
SYSCON
TO
DSP146
TO
DSP146
TO
CDS AGC A/D
JIG CN.
TO
CDS AGC A/D
JIG CN.
TO
DSP146
TO
SYSCON
TO
DSP146
TO
SYSCON
TO
JACK
TO
SYSCON
TO
DSP146
NOTE : The Parts Number, value and rated voltage etc. in the Schematic Diagram are for references only.
When replacing the parts, refer to the Parts List.