jWIN JD-VR70 User manual

jWINSheriff
V4.2
Operation Manual

2
Introduction

System Feature
jWINSheriff V4.2 provides advanced digital technology that supercedes old-fashioned
CCTV monitoring and VCR systems. It allows 'instant replay' and simultaneous recording.
jWINSheriff V4.2 also provides security personnel to define 'security events' that
require recording compression of non-event periods into a few frames of video for
continuity. This eliminates long hours of tape review and allows you to quickly find any date,
time or alarm by random access.
System Requirements
This chart reflects the minimum system requirements to operate jWINSheriff.
V4.2
ONE Card TWO CARDS
OS Windows98SE or Higher Windows98SE or Higher
CPU Pentium II 400MHz or Higher Pentium III 700MHz or Higher
Expansion Slot 1 PCI Slot 2 PCI Slot
System Memory 128MB or More 256MB or More
Video Memory 16MB or More 32MB or More (ATI Series)
Main board IBM PC Compatible Intel845, SiS645 Series or Higher
Hard Disc Space 10GB or More 20GB or More
DirectX Version 8.0 or Higher Version 8.0 or Higher
For Remote View Modem or Network Card Modem or Network Card
※In case of using above two card, Program might do not work according to the specification of
Main board or VGA adapter.
3

Installing jWINSheriff Board
1) Turn off power on the computer.
* It is very important to turn the computer’s power before you open the case. Static
Electricity can provide a big enough shock to damage the components of your PC. NEED
TO EXPLAIN ABOUT PROPER GROUNDING BEFORE TOUCHING ANY
COMPONENTS.
2) Open computer case and Please install as follows:
3) Check to make sure there is a PCI slot available.
<PCIslot>
4) Please install securely in the slot.
<PCIslotInstallation>
5) Secure the card in place by tightening the screw.
6) Close the case then turn on the computer
4
AGP (VGA) Slot
PCI Slot
ISA Slot

Install System
A User may connect CCTV camera, video phone, or video out port of any security
system to one of camera input ports on GVC capture card.
Also, a user may use TV out to connect an external analog CCTV monitor.
5
Video Out

Install Software
1) After installed jWINSheriff Board, and turn on your computer, automatically
display as below “Found New Hardware Wizard” program. At that time, click all of
“Cancel” button, and finished Wizard program. (according to a type of board and
quantity of board, can be repeated.)
2) To install jWINSheriff V4.2 software, You must insert ‘the installation CD' in your
CD-ROM drive.
3) Then, the installation program will run automatically. (If not, run 'Autorun.exe' file)
6

4) Select "Install Recorder".
5) Before installation takes place, a dialog box will ask whether it should install with driver.
If you selected “Yes”, it will install the jWINSheriff program with driver (The Driver is
needed to run this program. If this is your first installation of jWINSheriff on your
Computer, you must select “Yes”)
6) And then Installing device driver.
7) According to indicating the install program, click “Next” program.
8) Reboot computer, if you had done installation successfully. The jWINSheriff
program icon will appear on window of your desktop.
warning!※
jWINSheriff uses a specific data format. So, you must designate the specific
data file by using the setup program’s 'Storage Space' section after installation.
jWINSheriff will not record data without specific jWINSheriff storage space.
7

Main Screen Overview
Local Viewer: Run Local Viewer[Search]
Setup : Run Setup
Minimize/Close : Hide Button DVR Recorder in tray bar, and Close Button[Exit]
Video & Audio Recording Status : Status of Recording about Video and Audio
Warning: Display Warning Message
Screen Mode : Division of Display Screen [1,1/4,2/4,3/4,4/4,1/9,10/9,16,etc..]
Channel Rotation: Automatically Changing Channel
PTZ Control: PTZ basic button
PTZ Speed Control: Slide bar for PTZ moving speed
PTZ Extension: Button about expending PTZ control panel
Digital Out Switch: Switch button about Digital-out on Capture board
Exit: Exit Button
8
Local ViewerSetup
Minimize/
Close
Video &
Audio
Recording
Status
Warning
Screen Mode
PTZ
Control
Digital Out
Power
Channel
Rotation
PTZ
Extension
PTZ
Speed Control

9
SETUP

Preset ID and Password
The preset ID is set in “Administrator,” Password is set in “Admin.”
Setup Tree
General
- Display Device
- Video Input Signal
- Communication Setup(WebCam Server)
- PTZ Setup
- Save Image Quality
- Font
- Use Full screen mode
- Check Daily Reboot
- Use Password
- User Add/Delete
- Windows Shell mode
- Site Name
Sensor / Alarm Setup
Camera / Motion Detection
- Camera Setup
- Motion Setup
- Overlay Setup
- PTZ Receiver Setup
Audio Setup
Schedule Setup
Holiday / Recording Frame
- Holiday Registration
- Event Recording Setup
- Motion recording Setup
- On Time recording Setup
- Sensor recording Setup
Storage Space
ETC
- Using Line Monitor
- Using Alert Mode
10
- Notify E-mail