König SEC-DVR20 User manual

MANUAL
8CH (Two Page) DVR GEBRUIKSAANWIJZING 8-Kanaals (Twee Pagina's) DVR
SEC-DVR20

2
ENGLISH
Directory
Ⅰ. DVR Feature............................................................................................................3
Ⅱ. Outlook....................................................................................................................3
2.1. Front Panel...................................................................................................................................3
2.2. Rear Panel....................................................................................................................................4
2.3. Remote Controller .......................................................................................................................4
2.4. Removable HDD Box Introduction.............................................................................................5
Ⅲ. DVR Installation......................................................................................................6
3.1. Install Hard Disk...........................................................................................................................6
3.2. Connect Camera and Monitor ....................................................................................................7
3.3. Connect Power Cord...................................................................................................................7
Ⅳ. DVR System Boot...................................................................................................7
4.1. Detect installed Hard Disk ..........................................................................................................7
4.2. Recover Lost Data .......................................................................................................................7
4.3. Restore Recording Process .......................................................................................................8
4.4. Main Screen..................................................................................................................................9
Ⅴ. DVR Setup.............................................................................................................10
5.1. Setup Menu ................................................................................................................................10
5.2. Camera Select............................................................................................................................11
5.3. Record Select.............................................................................................................................11
5.4. Record Mode..............................................................................................................................11
5.5. Record Frame Rate....................................................................................................................11
5.6. Record Quality...........................................................................................................................11
5.7. Record Schedule .......................................................................................................................11
5.8. Sub Menu－Password Change.................................................................................................12
5.9. Sub Menu－Time set .................................................................................................................13
5.10. Sub Menu－Motion set..............................................................................................................13
5.11. Sub Menu－Password Set ........................................................................................................13
5.12. Sub Menu－Buzzer time............................................................................................................14
5.13. Hard Drive Setup........................................................................................................................14
5.14. Sensor Setup..............................................................................................................................15
5.15. NTSC/PAL Output Select...........................................................................................................16
Ⅵ. Record...................................................................................................................16
6.1. Start Recording..........................................................................................................................16
6.2. Stop Recording..........................................................................................................................17
6.3. Recording Length......................................................................................................................17
Ⅶ. Playback................................................................................................................18
Ⅷ. A/B Page Switch...................................................................................................19
8.1. Introduction................................................................................................................................19
8.2. Switch Function.........................................................................................................................19
IX. Specification.........................................................................................................20

3
I. DVR Feature
z8 Channel BNC Camera Input
z2 Channel BNC Monitor / VCR Output
zA / B Page Switch Function
zNTSC / PAL
zVideo Loss Alarm
zMotion Detection
z4 Sets NO / NC Sensor Input
z1 Alarm Output (2A 28VDC / 2A 125 VAC)
zOne ATA-100 Hard Disk Interface, Support Over 200G Byte
zRemovable HDD Box
zTime Schedule record/Sensor Triggered Record/Motion Triggered Record
II. Outlook
2.1 Front Panel
1 Channel 1 7 Move up 13 Play 19 Swap HDD
2 Channel 2 8 Select /Edit 14 Pause 21 Press-button
3 Channel 3 9 Move Down 15 Rewind 22 Key Locker
4 Channel 4 10 Record 16 HDD Access Indicator 23 Key
5 Quad View 11 Stop 17 Power Indicator 24 Active-handle
6 Menu /Exit 12 Forward 18 IR Window 25 Radiator
20 Enter/Exit the switchable state

4
2.2 Rear Panel
1. Video Output
2. Video Input
3. Sensor Input/Alarm Output
4. DC Power
5. Grounding
2.3 Remote Controller
1.CH1 Select or enlarge CH1
2.CH2 Select or enlarge CH2
3.CH3 Select or enlarge CH3
4.CH4 Select or enlarge CH4
5.QUAD Quad View
6.REW Rewind
7.PLAY Play record list
8.FWD Forward
9.RECORD Record
10.PAUSE Pause
11.STOP Stop recording or playing
12.MENU Enter or exit setup menu
13.Sel/Edit Modify item
14.UP Move up
15.DOWN Move down
16.CH1 Switch between CH1A and CH1B
17.A / B Switch between Quad1 and Quad2
18.CH2 Switch between CH2A and CH2B
19.CH3 Switch between CH3A and CH3B
20.CH4 Switch between CH4A and CH4B

5
2.4 Removable HDD Box Introduction
1 .Power Indicator
2 .HDD Access Indicator
3 .Key Lock
4 .PVC Frame
5 .Active-handle
6 .Radiator
7 .HDD data cable
8 .HDD power cable

6
III. DVR Installation
3.1 Install Hard Disk DISDisk
Fig1
Fig2
Fig3
(HDD is recommend to be provided by user)
Push the carrier body further into cartridge frame until
fully inserted (Fig3)
Slide the carrier body out of the cartridge frame (Fig1)
CAUTION
DON’T take out HDD when the DVR is running!
Connect the HDD data cable and the power cable to
the HDD(Fig2)

7
3.2 Connect Camera and Monitor
There are 8 camera inputs and 2 monitor outputs with a BNC connector.
3.3 Connect Power Cord
Please use the power adapter supplied with the DVR.
IV. DVR System Boot
4.1 Detect Installed Hard Disk
HDD Checking………..
MASTER HARD DRIVE
IBM—DHEA—36481
SLAVE HARD DRIVE
After the power is connected, system will boot-up
and detect the installed hard disk. The monitor
will show Master and Slave hard-disk
information.
Please refer to the hard disk manual to configure
the hard disk sequence. (Master or Slave)
A: Locked (Non-removable)
B: Unlocked (Removable)
A
B
Key Locker

8
4.2 Recover Lost Data
4.3 Restore Recording Process
SLAVE: RECOVER HDD?
04811-101735
(SELECT) YES/(MENU)NO
Power-Error will cause data loss and your
system will ask for ‘recover data’ at the next
step, please press [ Select] to proceed.
POWER ERROR DETECHED
RESTO REHARD
DISK(MASTER) OK
RESTORE REC MODE… OK
When a power-error occurs during the recording
process, system will automatically restore recording
process after you reconnect the power.

9
4.4 Main Screen
At first time DVR boot-up, all cameras are
OFF, please follow chapter 5-2 to switch on
all cameras.
λUpper leftÆRatio of Hard Disk
Space Used
λMiddle ÆChannel Name( CH1 ～
CH4)
λBottom rightÆDate and Time At
the moment, DVR is waiting for
command, press [ Menu] into DVR
setup process.

10
V. DVR Setup
5.1 Setup Menu
Menu Directory
Camera Select
Record Select
Record Mode
Record Frame Rate
Video Quality
Record Schedule
Sub Menu
Hard Drive Setup
Sensor Setup
0% MAIN MENU
＞CAMERA SELECT 1234
RECORD SELECT 1234
RECORD MODE EACH
REXORD FRAMERATE 30
VIDEO QUALETY NORMAL
RECORD SCHEDULE
SUB MENU
HARD DRIVE SETUP
SENSOR SETUP
PRESS（＜、＞）. THEN(SELECT)
PRESS(MENU) TO EXIT
Password Change
Time Set
Main Menu
Password Change
Time Set
Motion Set
Password Set
Buzzer Time
Press [ Menu] into setup menu, use [ Up]
and [ Down] to select item, press [ Select]
to modify settings and [ Menu] to confirm and
exit.

11
5.2 Camera Select
The system can display 4 cameras in one screen (Quad Mode). User can configure which camera to display.
Press [ Select ] to modify setting and press [ CH1 ],[ CH2 ], [ CH3 ],[ CH4 ] to set each channel
separately. If no channel is open, system will display [OFF] on monitor.
5.3 Record Select
Configure which channel is allowed to record.
5.4 Record Mode
There are two modes for video recording,
[Each Mode]: Compress and record each channel video separately, therefore, the user can enlarge a
single channel to full screen display. For example, user can turn off record function of CH1
and CH2 and then the system only records CH3 and CH4.
Press [ CH1 ],[ CH2 ],[ CH3 ],[ CH4 ] to switch between channels during
playback of recorded video.
[Quad Mode]: Compress and record all 4 channel video into one file, therefore user can not enlarge
single channel to full screen. User can’t use the each mode record in this mode.
5.5 Record Frame Rate
Record frame rate will affect the movement of objects in the recorded video. More frames means more smooth
movement and cost more hard disk space. System default value is 25 fps, that means system will record 25
frame per second. User can set frame rate as 25, 12, 8, 6, 4, 3, 2, 1 frames per second.
5.6 Record Quality
There are three level of record quality, High, Normal and Low. Higher quality costs more hard disk space.
Record frame rate, record quality and hard disk space will affect the total record time of your DVR system.
5.7 Record Schedule
Users can setup video record method by time, sensor Triggered and Motion Triggered.

12
5.8 Sub Menu—Password Change
System default password: Press six times [ CH1] button
+TTTMTMM-
TTTMMTTSSSTTT+
│││││││││
0 3 6 9 12 15 18 21 24
CURRENT PASSWORD :……
NEW PASSWORD :……
CONFIRM PASSWORD :……
All keys can be used as password key
except [ Menu ] key, which is used
for confirming and exit.
λ“-” No Record
λ“T” Continue, (System Default)
λ“S” Sensor Triggered.
λ“M” Motion Triggered.
Cooperate with many kinds of external sensor
equipment like PIR, Gas sensor. DVR will not
record video until an external sensor was
triggered and output signal to notify the DVR
during this specified period of time.
Button function:
[Up] [ Down]: move the prompt [ Select]:
Select Method.

13
5.9 Sub Menu—Time Set
5.10 Sub Menu—Motion Set
The first step, User need setup video record method by Motion Triggered. Please refer to 5.7.
After completed the “MOTION SET”, User can exit MENU, And press [ Record] to start Motion Record.
5.11 Sub Menu－Password Set
When password set is “ON”, Stop recording or entering a menu will need Password, if password set is “OFF”, no
password will be demanded.
2008/08/08 08:08:08
*
0%
MOTION SET
MOT LEVEL 5
MOT REC TIME 25
MOT LEVER: User can press [ Select] to
adjust sensitivity grade of motion detection.
High (1----------10) Low
MOT REC TIME: Recording time setup when
motion detected. User can press [ Select] to
set the time.
Time Setup: 5sec~30sec
Configure DVR system time. Press [ Up] and
[Down] to move prompt and press [ Select] to
modify. Press [ Menu] to finish input and exit.

14
5.12 Sub Menu－Buzzer Time
Buzzer time set (00,05,10,15,20,25,30 seconds and CONT) , User can press [ Select ] to set the time .When
Buzzer Time is “00”,All the buzzers will be shut off. When “Buzzers Time” is “CONT”, the buzzer will work
continuously.
5.13 Hard Drive Setup
MASTER HDD USED
It shows the space used on the first hard disk drive for recording and the percent of the used hard disk.
MASTER HDD FORMAT
If you format the hard drive, it will erase all the data recorded on the first hard disk drive.
SLAVE HDD SIZE
It shows the space available on the secondary hard disk drive installed in the DVR.
SLAVE HDD USED
It shows the space used on the primary hard disk drive available for recording.
SLAVE HDD FORMAT
If you format the hard drive, it will erase all the data recorded on the secondary hard disk drive.
HARD DRIVE SETUP
＞ORERORITE ENABLE [YES]
MASTER HDD SIZE 40042MB
MASTER HDD USED 80865MB %77
MASTER HDD FORMAT
SLAVE HDD SIZE N/A
SLAVE HDD USED N/A
SLAVE HDD FORMAT
PRESS(＜＞) THEN （SELECT）
PRESS（MENU）TO EXIT
OVERWRITE ENABLED
If you choose YES, recording continues and
overwrite previous recording when hard disk
drive space is full.
If you choose NO, the recording session
stops when hard disk drive is full.
MASTER HDD SIZE
It shows the size of the primary hard disk
drive installed in the DVR.

15
5.14 Sensor Setup
Push the UNLOCK BUTTON to insert the wire
There are 3 different modes for sensor setting:
NOT INSTALLED, NORMAL-CLOSE and NORMAL-OPEN.
It depends on what type of external sensor user use, If sensor’s output is NORMAL-OPEN then select
NORMAL-OPEN mode in DVR.
If sensor triggered by an intruder then the cable line connects to DVR input terminal will notify system to
start recording.
There are four pairs of input terminal supported by DVR.
SENSOR SETUP
＞SENSOR RECORD TIME 10
ALARM OUT TIME 05
CHANNEL-1 TYPE:NORMAL-OPEN
CHANNEL-2 TYPE:NORMAL-CLOSE
CHANNEL-3 NOT INSTALLED
CHANNEL-4 NOT INSTALLED
SENSOR RECORD TIME
The number indicates how long sensor
recording lasts when the sensor indicates the
movements in front of the camera.
ALARM OUT TIME
It controls how long (in seconds) the alarm
lasts after it sets off.
Value 0 will turn off alarm output.
Select Cont will turn on alarm output until
user press any key.

16
Install example diagram：
5.15 NTSC/PAL Output Select
Change jump JS1 to select NTSC or PAL video output format according to the silkscreen on the PCB.
VI. Record
6.1 Start Recording
Press [Record] to start recording. System will display some information on Screen.
*Only EACH MODE can enlarge single channel to full screen display
Connect PIR sensor
NO/NC output to DVR
input terminal.
(Max. 5V DC)
DVR
Alarm
Power
PIR Sensor
Power
NTSC/PAL Select

17
λ①Hard Disk Usage Ration
λ②Recording Symbol
λ③Channel Names
λ④Mode (QUAD or EACH)
λ⑤Status (REC, Play, FF1, FF2, FF3, REW, PAUSE)
λ⑥HD Info. ([M] Master disk [S] Slave disk)
λ⑦Schedule((T) Continuous (S) Sensor (－) No Record
λ⑧When [ * ] show up beside date & time , it indicate that system are overwrite.
6.2 Stop Recording
Press [ Stop] and system will prompt to input password. Only correct password can stop recording process.
6.3 Recording Length

18
User can calculate and estimate record hours by below formula
120G Byte @ 7 frames per second @ Normal quality
120 (G byte) x 1024 (M byte) x 1024 (K byte)
15 (Kbyte/frame) x 7 (frame/sec) x 60 (sec) x 60 (min)
Estimate hours is 332 Hours
VII. Playback
Press [ Play] then system will list all recorded video clip from HD. Newest video will at top of the list, press
[ Up ] and [ Down ] to select start time and press [ Play ] again to start play video to the end.
Format Quality Frame Rate 30 15 7 1
HIGH 20 58 117 251 1748
NORMAL 15 78 155 333 2330
NTSC
LOW 12 97 194 416 2913
Format Quality Frame Rate 25 12 6 1
HIGH 20 70 146 291 1748
NORMAL 15 93 194 388 2330
PAL LOW 12 117 243 485 2913

19
1. HD Information 2. Start Time
3. End Time 4. TIME: Continue record
5. SENSOR: Sensor triggered 6.Motion:Motion triggered
Another way to search video is directly input time period. Press [ Forward] and then press [ Up ] and [
Down ] to select digit. Press [ Select] to edit time value and press [ Play] to play video.
VIII. A/B PAGE SWITCH
8.1 Introduction
There are 8channels for video input supplied by this product, which are CH1A, CH2A, CH3A, CH4A, CH1B,
CH2B, CH3B and CH4B. You can view 4 of these channels simultaneously in QUAD VIEW instantly. But you can
view the other channels by the means of A/B PAGE SWITCH Function.
8.2 Switch Function
There are two methods to switch channels between A and B pages:
[Use the front panel]: press [A B], the [PWR] LED turns red.
Then
Press [CH1], switch between CH1A and CH1B channel
Press [CH2], switch between CH2A and CH2B channel
Press [CH3], switch between CH3A and CH3B channel
Press [CH4], switch between CH4A and CH4B channel
Press [QUAD], switch between current 4channels and other 4 channels
Finally, press [A B] to exit the switchable state.
[Use the remote controller]: use the button in the [A/B PAGE SWITCH] area.
Press [CH1], switch between CH1A and CH1B channel
Press [CH2], switch between CH2A and CH2B channel
Press [CH3], switch between CH3A and CH3B channel
Press [CH4] switch between CH4A and CH4B channel
Press [A/B] switch between current 4channels and other 4 channels
0 8 /0 8 / 0 8 1 5 : 0 3 : 3 2 --0 8 / 0 8 / 0 8 1 6 : 2 8 : 1 2
*

20
IX. Specifications
ITEM DESCRIPTION NOTE
Video Format NTSC / PAL
Operation System None STAND-ALONE
Camera Input Channel 8 channel Composite BNC
Video Output Channel 2 channel Composite BNC
NTSC 120 frames/second 4 x 30 frames/second
Display Frame Rate PAL 100 frames /second 4 x 25 frames/second
NTSC Max 30 fps (Quad) Quad ModeRecording Frame Rate
(Quad) PAL Max.25 fps (Quad) Quad Mode
NTSC Each Channel =
30 ÷ Number of Source
Max. 30 frames/s
(Each Channel)
Recording Frame Rate
(Each Mode) PAL Each Channel =
25 fps ÷ Number of Source
Max. 25 frames/s
(Each Channel)
Record Mode Continuous, Schedule, Motion
Triggered ,Sensor Triggered
Display NTSC：720 x 480
PAL：720 x 576
Resolution
Record NTSC：320 x 112, 640 x 224
PAL：320 x 136, 640 x 272
Quad：640 x 224 (total)
Each：640 x 224
Video Compression Format
(Each Channel)
Modified Motion-JPEG
(12-20K bytes/frame)
Low :12K Byte
Normal :15K Byte
High : 20K Byte
HDD Support Over 200G Byte ATA -100 Interface
Estimated Record Length 120G Hard disk @ 7 fame per second @ Normal Quality
(120*1024*1024 K byte) ÷ ( 7*15*60*60 ) = 332 Hours
Method Time、Date、Event
Search Full Screen YES
Voice None
Sensor, Alarm
4 Input (Normal Open / Normal Close)
1 Input (Relay 2A 28VDC / 2A 125VAC)
Video Signal Loss Alarm
PTZ None
Dimension Length 315mm * Width 224mm * Height 52mm