Küppersbusch EKWI 3740.O W User manual

MONTAGEANWEISUNGEN
Installation instructions
Manuel d’installation
Montagehandleiding
EKWI 3740.O W / S

10
SUMMARY
DESCRIPTION OF THE APPLIANCE.......................................................................................11
APPLIANCES AND INSTALLATION DIMENSIONS...............................................................................11
MULTIZONES INSTALLATION ................................................................................................12
INSTALLATION...........................................................................................................................12
VENTILATION ............................................................................................................................12
INSTALLATION INSTRUCTIONS.....................................................................................................13
CONNEXION OF THE DIFFERENT ELEMENTS......................................................................13
CONNECTION OF COOKING ZONES ..............................................................................................13
CONFIGURATION PROCEDURE.............................................................................................15
WHAT TO DO IN CASE OF A PROBLEM................................................................................15
ELECTRICAL CONNECTION...................................................................................................16

11
DESCRIPTION OF THE APPLIANCE
Appliances and installation dimensions
Dimension
Heating zone Finger touch
5
7
C
Reference 703879-02 703879-03 703879-01
703880-01
Dimension of
glass A 320mm 320mm
Diameter of the
throat B 326mm 326mm
Thickness of
glass 4mm 4mm
Cut-out Dimen-
sion C 302mm 180 x 113 mm
Height total 57mm 35mm
Diameter of the
inductor 160mm 200mm
Power 1100W 2300W
Booster 2500W 3000W
Dimensions of the technical box 703879-04 : 260x211x48

12
MULTIZONES INSTALLATION
Installation
Unpack all the material.
The installation and connection of the appliance have to be done by approved
specialists. The manufacturer can not be held responsible for damage caused by
building-in or connecting errors.
The appliancemust be well-equipped and installed in a kitchen unit and an adapted and
approved work surface.
This domestic appliance is exclusively for the cooking of food, to the exclusion of any
other domestic, commercial or industrial use.
Remove all labels and self-adhesives from the ceramic glass.
Do not transform or modify the appliance.
The cooking zones and the control panel should not be used as support or worktop.
The appliance must be grounded and connected conform to local standards.
Do not use any extension cable to connect it.
The appliance can not be used above a dishwasher or a tumble-dryer: steam may
damage the electronic appliances.
Ventilation
Important: the cooling system needs some airflow.
Take into account to keep the gap in front of the air inlet of the cooling fan

13
Installation instructions
The installation comes under the exclusive responsibility of specialists.
The installer is held to respect the legislation and the standards used in his home country.
Fitting - installing:
The piece of furniture or the support in which the hob has to be fitted, as well as the
edges of furniture, the laminate coatings and the glue used to fix them, must be able to
resist temperatures of up to 100 °C.
The mural rods of edge must be heat-resisting.
The hobs are classified as “Y” class for heat protection. Ideally the hob should be
installed with plenty of space on either side. There may be a wall at the rear and tall units
or a wall at one side. On the other side, however, no unit or divider must stand
higher than the hob.
Ensure that there is a distance of 50 mm between the hob and the wall or sides.
Materials which are often used to make worktops expand on contact with water. To
protect the cut out edge, apply a coat of varnish or special sealant. Particular care must
be given to applying the adhesive joint supplied with the hob to prevent any leakage into
the supporting furniture. This gasket guaranties a correct seal when used in conjunction
with smooth work top surfaces.
The safety gap between the hob and the cooker hood placed above must respect the
indications of the hood manufacturer. In case of absence of instructions respect a
distance minimum of 760 mm.
The connection cords should be subjected, after building in, with no mechanical
constraint, such as for example the drawer.
CONNEXION OF THE DIFFERENT ELEMENTS
The installation of this appliance and the connection to the electrical network should be made by
an electrician perfectly aware, and in respect of the normative regulations
Connection of cooking zones
Each connector of the cooking zones, is located by a sticker with the classification from
5 to 8 corresponds to:
5: Heating zone 1100 W
7: Heating zone 2300 W
The fingertouch electronic is located by “C” on the connector
On the technical box, near the female connectors are written: 5-6-7-8-C.
Connect the fingertouch on the “C” of the technical box.
Connect the heating zones with the corresponding number on the technical
box.
To connect easily, begging with the biggest number of the heating zone.

14
Example:
Nota: - It is strictly forbidden to lengthen or shorten the wire of the cooking zones.
- We do not take any responsibility in cas of not respecting the connections
indicated and the safety warnings.

15
a
d
c
b
CONFIGURATION PROCEDURE
The table must be configured. Please implement the following steps:
I) Important!Before you start, make sure there is no more pot on the hob
II) Disconnect the appliance from the grid by removing the fuse or turning the circuit breaker off
III) Reconnect the table to the grid
IV) Procedure:
* Take a pot with a ferromagnetic bottom with a minimum diameter of 16 cm
* start the procedure within 2 minutes after reconnecting the hob to the grid
* don’t use the [ O/I ] touch
V) First step: cancel the existing configuration
1) Press the touch n°2 and hold down
2) The symbol [ - ] will appear on each display
3) With your other hand, press successively and
quickly (less than 2s) on each [ - ] display.
Begin from the front right side and turn contrary
clockwise, as described on the picture (a -> b -> c -> d)).
A double "beep" means an error occurred. If so, start again from item 1).
4) Remove your fingers from the touch control, then push again on touch 1 during few
seconds, until blinking [ E ] symbols appear.
5) Wait until [ E ] symbols stop blinking.
6) After few seconds, [ E ] are automatically transformed in [ C ].
The existing setup has been cancelled.
VI) Second step: new setup
Take a pot with a ferromagnetic bottom with a minimum diameter of 16 cm2) Select
a cooking zone by pushing on the corresponding [ C ] display
3) Place the pot on the area to be set
4) Wait until the [ C ] display becomes a [ - ]. The selected cooking zone is now
configured.
5) Follow the same procedure for each cooking zone with a [ C ] display.
6) All the cooking zones are configured once all the displays are turned off.
Note: …..Please use the same pot for the whole procedure.
Never put several pots together on the zones during the setup-process.
WHAT TO DO IN CASE OF A PROBLEM
The symbol [ E4] appears :
Reconfigure the table
If the symbol remains, please contact the After sales service

16
ELECTRICAL CONNECTION
The installation of this appliance and the connection to the electrical network should be
entrusted only to an electrician perfectly aware, and in respect of the normative
regulations
Protection against parts under tension must be ensured after the building.
The data of connection necessary are on the stickers place on the hob casing near the
connection box.
The connection to the main must be made using an earthed plug or via an omnipolar
circuit breaking device with a contact opening of at least 3 mm.
The electrical circuit must be separated from the network by adapted devices, for
example: circuit breakers, fuses or contactors.
If the appliance is not fitted with an accessible plug, disconnecting means must be
incorporated in the fixed installation, in accordance with the installation regulations.
The inlet hose must be positioned so that it does not touch any of the hot parts of the hob
or oven.
CONNECTION OF THE HOB
For the various kinds of connection, use the brass bridges which are in the box next the
terminal.
Caution!
- Connect always the earth wire.
- Respect the connection diagram.
- This device is intended for a supply of 230 V ~ 50/60 Hz
- The connection box is located underneath at the back of the hob casing. To open the cover
use a medium screwdriver. Place it in the slits and open the cover.
( * ) calculated with the simultaneous factor following standard EN 60 335-2-6/1990
Important
It is forbidden to extent or to shorten the liaison wires areas of the cooking zones ( 5,6,7,8; see
page 6)Only the control panel (C) may be extended (Order our only lengthens ref A10506/0).
Monophase 230V~1P+N:
Put the 1st bridge between terminal 1 and 2, the 2nd between 3 and 4.
Attach the earth to the terminate “earth”, the neutral N to terminal 3 or 4, the Phase L to one of
the terminals 1 or 2.
Biphase 400V~2P+N:
Put a bridge between terminal 3 and 4.
Attach the earth to the terminate “earth”, the neutral N to terminal 3 or 4, the Phase L1 to the
terminals 1 and the Phase L2 to the terminal 2.
Caution! Be careful that the cables are correctly engaged and tightened.
We cannot be held responsible for any incident resulting from incorrect connection or
which could arise from the use of an appliance which has not been earthed or has been
equipped with a faulty earth connection.
Mains Connection Cable diameter
Cable Protection calibre
230V~ 50/60Hz 1 Phase + N 3 x 2.5 mm² H 05 VV - F
H 05 RR - F 25 A *
400V~ 50/60Hz 2 Phases + N 4 x 1.5 mm² H 05 VV - F
H 05 RR - F 16 A *