K-sun Green Machine User manual

GM_horizontal_ vertical stacked oset
GM_horizontal
1-color black
Version 4.10
MANUAL
Indication of the manufacturer and the importer
in
accordance with requirements of directive
2011/65/EU
(RoHS)
Manufacturer:
K-Sun Corporation
Address:
370 SMC Drive
Somerset WI 54025
Phone:
715-247-4440
Importer:
Address:
Phone:
Use
Adapter Model AST1116Y1-1
Input
AC100-240V, 0.4A, 50-60Hz
(dedicated
adapter, power cable only)
Output
DC 11V, 1.64A
®
Indication of the manufacturer and the importer
in
accordance with requirements of directive
2011/65/EU
(RoHS)
Manufacturer:
K-Sun Corporation
Address:
370 SMC Drive
Somerset WI 54025
Phone:
715-247-4440
Importer:
Address:
Phone:
Use
Adapter Model AST1116Y1-1
Input
AC100-240V, 0.4A, 50-60Hz
(dedicated
adapter, power cable only)
Output
DC 11V, 1.64A
®

Federal Communications Commission (FCC)
Declaration of Conformity
K-Sun®Corporation
370 SMC Drive, PO Box 309
Somerset, WI 54025
Phone: [phone]
Product Name: LABELShop® GREEN MACHINE®
Model Number: LABELShop® K-Sun®GREEN MACHINE®
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme á la nomme NMB-003
du Canada.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This Equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• To ensure compliance with the limits for a Class B digital device the
enclosed interface cable should be used. (If Applicable)
• Modications or changes not expressly approved by K-Sun® Corporation
could void the user’s authority to operate the equipment.

Introduction
Thank you for purchasing K-Sun®GREEN MACHINE®.
This manual is divided into five sections
1. Getting Started
2. Basic Operations 1 - for new users
3. Basic Operations 2 - more advanced features
4. Telcom/Electrical Label Mode
5. Additional Functions
Please read this manual before using your K-Sun® GREEN MACHINE®.
This manual contains CAUTION and WARNING notices which must be observed
and tips that can assist you complete the task more easily and more effectively.
Be sure to keep this manual handy for future references.
●All rights reserved. No part of this manual may be reproduced, stored in a retrieval system,
or transmitted in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without our prior written permission.
●The contents of this manual are subject to change without notice.
●All effort have been made to ensure the accuracy of the contents of this manual.
However, should any errors be detected, we would greatly appreciate being informed of
them.
•Texts you have entered are temporary saved in this device, but not kept for extended
period of time. We shall not be liable for damages, losses, costs, or expenses incurred as
a result of malfunction, repair, test, or battery exhaustion of this device.
•About the labels
Before attaching labels, be sure to check the purpose of use and the material of the
adhered surface. Depending on the material, environmental conditions, etc., following
problems may occur.
-Color of the labels changes
-Labels come off
-Texts on the label wear off
-Cannot peel off the labels
-Glue remains on the adhered surface
-The adhered surface absorbs the color of the label
-The adhered surface is damaged
We shall not be liable for any damages, losses, costs, or expenses arising from these
problems.
•Do not carry out any operations not described in this manual, or K-Sun®GREEN
MACHINE®may break or cause injury.

Using This Manual
About this manual
This manual contains the following sections:
Getting Started
Describes preparations required before using K-SunGREEN MACHINE®.
Basic Operations
Divided into three sections.
"Basic Operation 1" explains operations such as entering texts and attaching labels.
"Basic Operation 2" explains more advanced operations such as adding new paragraph.
(The + key)
"Telcom/Electrical Mode" explains how to create a label that wrapsaround a cable or any other
cylindrically-shaped object.
If you are a first-time user, reading from the "Basic Operation 1" is recommended.
Additional Functions
Describes useful information that can assist you to complete the task more easily and more
effectively. Read and understand "Basic Operations 1" and "Basic Operations 2" before you
begin on this section.
Symbols used in this manual
The following symbols are used in this manual:
Labels in this manual: Labels contained in this manual are all samples and may differ from
actual labels.
Symbol Description
, Indicates operation procedures.
, Indicates the character keys.
Symbols or characters on the upper part of buttons may be omitted.
, , Indicates the function keys.
Indicates the keys to move the cursor or select an item.
See Introduces the reference pages. Refer to the specified pages as
necessary.
Indicates useful tips.
Explains limitations and conditions that you should be aware of.

INTRODUCTION
• Important Safety Precautions ....... 1
Warning ........................... 2
Caution ............................ 4
Precautions ..................... 5
General Cautions ............ 6
GETTING STARTED
• Parts Location .............................. 9
• Keys ............................................. 11
• Display Indicators ......................... 14
• Switching to Graphic Display ........ 15
• Adjusting Display Level, Backlight . 16
• Setting Display Language/Units ... 17
• Preparing the machine for use ..... 18
AC Adapter ....................... 18
Batteries ........................... 18
Tape Cartridge ................. 21
Turning On ....................... 23
Feeding Tape ................... 24
• Supply Cartridge Reference Guide
Shrink Tube .................... 26
Labeling Tape ................. 27
Wire Wrap ...................... 29
BASIC OPERATIONS 1
• Entering Text ................................ 32
• Entering Text Using Euro/Latin Key 33
• Inserting Space ............................ 33
• Entering Symbol ........................... 34
• Preview ........................................ 36
• Printing ......................................... 37
• Attaching Label ............................. 38
• Power Off ..................................... 39
BASIC OPERATIONS 2
• Editing Text .................................. 42
• Cursor Keys ................................. 42
• Delete Insert Text ......................... 43
• Adding Lines ................................ 44
• Moving Text, Joining Lines ........... 45
• Adding Paragraphs/Columns ....... 46
• PeelGuard®/Rounding Corners .... 48
• Cleaning Machine Exterior ........... 49
• Cleaning PeelGuard® Tray ........... 49
• Cleaning Print Head ..................... 50
TELECOM/ELECTRICAL
LABEL MODE
• Patch ............................................ 52
• Wrap ............................................ 54
• Flag .............................................. 56
ADDITIONAL FUNCTIONS
• Changing Font Type ..................... 58
• Changing Text Size ...................... 58
• Edit Key Functions ....................... 59
Setting Functions ............. 60
Edit Menu - English ......... 62
• Function Description
Length ............................. 65
Frame & Table ................. 66
Margin ............................. 67
Layout ............................. 67
Decorate .......................... 68
Space .............................. 68
Border & Line ................... 69
Wide & Narrow ................. 69
Background ...................... 69
Bold & Italic ...................... 70
Vertical ............................. 70
Vertical - 2 Digit Number .. 71
Line Size/Text Size .......... 72
Font Type ......................... 73
• Printing Sequence Numbers ........ 74
• Printing Bar Codes ....................... 76
• Extra Key Print Functions
Extra Print Menu-English . 79
Enlarge ............................ 80
Repeat ............................. 83
Mirror ............................... 85
• Print Setting Functions
Print Setting Menu-English . 86
Adjusting Print Density ..... 86
Auto Cut-On/Off ............... 87
Memory Reset .................. 88
• Store/Recall
Saving a File .................... 89
Recalling a File ................ 90
Deleting a File .................. 91
• Print History
Recall ............................... 92
Delete ............................... 93
• User’s Symbols ............................ 94
… continued on next page
8Introduction
Contents
●Introduction
●Important Safety Precautions................. 1
Precautions when using
tape cartridges.................................... 5
Precautions when installing
tape cartridges.................................... 5
General cautions................................. 6
●Using This Manual ................................. 7
About this manual ............................... 7
Symbols used in this manual .............. 7
●Contents................................................. 8
●Quick Start Guide................................. 10
1.Preparation .................................... 10
2.Entering texts (Example: NAME)... 10
3.Printing labels ................................ 11
●Attaching labels..................................... 11
●K-Sun GREEN MACHINE®Parts........ 14
Top side ............................................ 14
Internal parts..................................... 14
Bottom............................................... 15
Printer Back ...................................... 15
K-Sun GREEN MACHINE®Keys..... 16
●Display Indicators................................. 19
Display indicators.............................. 19
Switching display (Graphic) .............. 20
Adjusting Display Level..................... 21
Backlight ........................................... 21
Setting the Display Language........... 22
Setting the Display Units................... 22
●Preparation .......................................... 23
1.Connecting the bundled
AC adapter........................................ 23
2.Installing the batteries.................... 23
3.Installing tape cartridges................ 26
4.Turning the power on..................... 28
●Feeding the tape.................................. 29
1.Entering text................................... 32
2.Inserting space............................... 34
3.Entering symbol............................. 34
4.Viewing print image (Preview) ....... 36
5.Printing label.................................. 37
6.Attaching label ............................... 38
●Turning the Power Off.......................... 39
●Editing Text .......................................... 42
Using the cursor keys........................ 42
Entering text...................................... 42
Deleting/Inserting text ....................... 43
Deleting all the text............................ 43
●Adding New Lines (Line Break)............ 44
Starting a new line............................. 44
Moving the text to the next line ......... 45
Joining the two lines.......................... 45
●Adding New Paragraphs [ + ]... 46
Starting a new paragraph.................. 46
Dividing into paragraphs ................... 47
●Rounding Off the Corners.................... 48
●Cleaning K-Sun GREEN MACHINE®.. 49
To remove dirt and dust
from the exterior................................ 49
Cleaning PeelGuard®....................... 49
●Cleaning the print head
(faint printing) ....................................... 50
●Telecom/Electrical Label Mode............ 52
Creating the label in
Telecom/Electrical Label Mode......... 53
List of "Telecom/Electrical Label
Mode" menu...................................... 55
●Changing the font type......................... 58
Using key .................................... 58
●Changing the font/text size................... 58
Using key.................................... 58
●Improving the Appearance of the Label
- Using the decoration functions - ........ 59
Setting functions................................ 60
●List of Edit menu (English)................... 62
Function description.......................... 65
Printing sequence numbers .............. 74
●Printing Bar Codes............................... 76
Creating a label with a bar code........ 76
Bar code printing............................... 76
●Extra Print Functions............................ 79
List of "Extra Print" menu.................. 79
To create a label that is wider than
the width of the tape (Enlarge).......... 80
Prints the same label
continuously (Repeat)....................... 83
Introduction
Getting Started
Basic Operations 1
Basic Operations 2
Telecom/Electrical Label Mode
Additional Functions

8Introduction
Contents
●Introduction
●Important Safety Precautions................. 1
Precautions when using
tape cartridges.................................... 5
Precautions when installing
tape cartridges.................................... 5
General cautions................................. 6
●Using This Manual ................................. 7
About this manual ............................... 7
Symbols used in this manual .............. 7
●Contents................................................. 8
●Quick Start Guide................................. 10
1.Preparation .................................... 10
2.Entering texts (Example: NAME)... 10
3.Printing labels ................................ 11
●Attaching labels..................................... 11
●K-Sun GREEN MACHINE®Parts........ 14
Top side ............................................ 14
Internal parts..................................... 14
Bottom............................................... 15
Printer Back ...................................... 15
K-Sun GREEN MACHINE®Keys..... 16
●Display Indicators................................. 19
Display indicators.............................. 19
Switching display (Graphic) .............. 20
Adjusting Display Level..................... 21
Backlight ........................................... 21
Setting the Display Language........... 22
Setting the Display Units................... 22
●Preparation .......................................... 23
1.Connecting the bundled
AC adapter........................................ 23
2.Installing the batteries.................... 23
3.Installing tape cartridges................ 26
4.Turning the power on..................... 28
●Feeding the tape.................................. 29
1.Entering text................................... 32
2.Inserting space............................... 34
3.Entering symbol............................. 34
4.Viewing print image (Preview) ....... 36
5.Printing label.................................. 37
6.Attaching label ............................... 38
●Turning the Power Off.......................... 39
●Editing Text .......................................... 42
Using the cursor keys........................ 42
Entering text...................................... 42
Deleting/Inserting text ....................... 43
Deleting all the text............................ 43
●Adding New Lines (Line Break)............ 44
Starting a new line............................. 44
Moving the text to the next line ......... 45
Joining the two lines.......................... 45
●Adding New Paragraphs [ + ]... 46
Starting a new paragraph.................. 46
Dividing into paragraphs ................... 47
●Rounding Off the Corners.................... 48
●Cleaning K-Sun GREEN MACHINE®.. 49
To remove dirt and dust
from the exterior................................ 49
Cleaning PeelGuard®....................... 49
●Cleaning the print head
(faint printing) ....................................... 50
●Telecom/Electrical Label Mode............ 52
Creating the label in
Telecom/Electrical Label Mode......... 53
List of "Telecom/Electrical Label
Mode" menu...................................... 55
●Changing the font type......................... 58
Using key .................................... 58
●Changing the font/text size................... 58
Using key.................................... 58
●Improving the Appearance of the Label
- Using the decoration functions - ........ 59
Setting functions................................ 60
●List of Edit menu (English)................... 62
Function description.......................... 65
Printing sequence numbers .............. 74
●Printing Bar Codes............................... 76
Creating a label with a bar code........ 76
Bar code printing............................... 76
●Extra Print Functions............................ 79
List of "Extra Print" menu.................. 79
To create a label that is wider than
the width of the tape (Enlarge).......... 80
Prints the same label
continuously (Repeat)....................... 83
Introduction
Getting Started
Basic Operations 1
Basic Operations 2
Telecom/Electrical Label Mode
Additional Functions
FUNCTIONS …CONTINUED
• Condition
Condition Menu-English ....... 101
Setting Battery Type ............. 102
Setting to Default .................. 103
Change Default Settings ...... 104
• Resetting ........................................... 105
APPENDIX
• Symbols Menu - English ................... 108
• Pictograph Menu - English ................ 109
DISPLAY MESSAGES ............ 110
PROBLEMS & SOLUTIONS ..... 112
LIST OF CHARACTERS
• Key Layout ....................................... 116
• Character Table ............................... 116
• Additional Keys ................................ 117
SPECIFICATIONS .................. 118
SYMBOLS LIST ...................... 121
PICTOGRAPH LIST ............... 123
FRAME & TABLE LIST .......... 125
EURO LATIN CHARACTER LIST 126
MENUS BY LANGUAGE
• English ............................................ 127
• Spanish/Español ............................. 135
• French/Français .............................. 143
• German/Deutsch ............................. 151
• Italian/Italiano .................................. 159
• Danish/Dansk .................................. 167
• Swedish/Svenska ............................ 175
• Finnish/Suomi .................................. 183
• Norwegian/Norsk ............................. 191
• Russian/Pycckий ............................. 199
• Croatin/Hrvatski ............................... 207
• Greek/Eλλŋνıĸά ............................... 215

Introduction 1
Important Safety Precautions
Items below should always be followed to protect users, their surroundings and their
property from possible injury or damage. Be sure to read and understand the
instructions before using your K-Sun®GREEN MACHINE®and keep this manual handy
for future references.
●Precautionary notations throughout the text are categorized relative to 1) personal injury
and 2) damage to equipment.
●Please familiarize yourself with the following definitions and meanings for each symbol
before reading the precautions.
DANGER Signals a precaution which, if ignored, will result in serious
or fatal personal injury. Pay extra caution in performing
procedures preceded by DANGER headings.
WARNING Signals a precaution which, if ignored, could result in
serious or fatal personal injury.
CAUTION Signals a precaution which, if ignored, could result in
damage to equipment.
Important reminder
Prohibited
Mandatory
DANGER
When using the battery
If liquid leaking from the battery gets into your eyes, do not rub your
eyes. Wash them well with clean water and contact a doctor
immediately.

2Introduction
WARNING
Only use AC adapter AST1116Y1-1 that comes with the product. When using the AC
adapter, make sure to observe the following precautions.
Do not attempt to use any adapters other than the AC adapter
bundled with the device. This may cause damage, overheating, fire,
or electric shock.
Be sure to use the AC adapter with the proper voltage. Using it with
other voltage levels may cause fire, smoke, overheating, or electric
shock. Proper voltage is AC 120V.
Do not pull the AC adapter cord excessively or put a heavy object
on it. This may cause fire or electric shock.
WARNING
When using the battery
Do not use batteries with their and terminals reversed. This
may cause leakage, overheating, or explosion.
If liquid from the battery enters your mouth, rinse immediately with
plenty of water and consult a doctor.
If liquid from the battery comes in contact with your skin or cloth,
wash away with water. This may cause damage to your skin.
Do not use a new battery and an old battery, or different types of
batteries at the same time. Doing so may cause leakage,
overheating, or explosion.
When the battery runs down, take it out of the device immediately. If
a flat battery is left inside the device for long periods, gas emitted
from the battery may cause leakage, overheating, explosion, or
damage to the device.
If you do not use K-Sun®GREEN MACHINE®for an extended
period, take out the batteries from the device. Gas emitted from the
battery may cause leakage, overheating, explosion, or damage to
the device.
Not bundled
AC adapter
Not specified
battery

Introduction 3
Follow the instructions given on the label or a package of the
battery. Misuse of the batteries may cause leakage, overheating,
explosion, injury, or damage to the device.
If you use nickel-hydride rechargeable batteries (The SANYO
eneloop HR-3UTGA or HR-3UTGB are the only tested and approved
nickel-hydride rechargeable batteries for use in the K-Sun®
GREEN MACHINE®follow the instructions on the battery and the charger.
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instruction.
WARNING
Other Do not step on, drop, hit, or have strong impacts on this device. This
may cause fire or electric shock. If your K-Sun®GREEN MACHINE®
®
is damaged, turn the power off, remove the bundled AC adapter
from the electrical outlet, and contact local distributor. Using the
damaged device may cause fire and electric shock.
Do not touch the device, the bundled AC adapter, or the plug with
wet hands. This may cause malfunction, fire, or electric shock.
Keep plastic bags out of reach of children. Children may suffocate if
they swallow or put their heads into plastic bags.
Do not spill liquid or spray insecticide onto K-Sun®GREEN
MACHINE®. This may cause malfunction, fire, or electric shock. If
you spilled liquid, turn the power off, remove the bundled AC
adapter from the electrical outlet, and contact local distributor.
Using the damaged device may cause fire and electric shock.
Never modify or disassemble the device. This may cause fire or
electric shock. Do not carry out any operations not described in this
manual, or K-Sun GREEN MACHINE®may break or cause injury.
WARNING
Instructions
Instructions
Instructions
If you use nickel-hydride rechargeable batteries
(The SANYO eneloop HR-3UTGA or HR-3UTGB are the only tested
and approvednickel-hydride rechargeable batteries for use in the
K-Sun® GREEN MACHINE® follow the instructions on the battery
and the charger.
Risk of explosion if battery is replaced by an incorrect type.Dispose of
used batteries according to the instruction.

4Introduction
CAUTION
Cleaning PeelGuard®
Be sure to turn the power off before removing the PeelGuard®tray.
When cleaning, do not put your fingers inside the PeelGuard®.
Otherwise, you might cut your fingers.
Auto-cutter
Keep your fingers off the exit slot where the labels come out during
printing or when the cutter is operating. This may cut your fingers.
Other Do not put anything heavy on K-Sun GREEN MACHINE®or leave it
in unstable position. This may cause injury or damage to the device.
Always turn the power off before removing the bundled AC adapter
from the electrical outlet. This may cause malfunction of the device.
About the labels
Before attaching labels, be sure to check the purpose of use and
the material of the adhered surface. Depending on the material,
environmental conditions, etc., following problems may occur.
•Color of the labels change
•Labels come off
•Texts on the label wear off
•Cannot peel off the labels
•Glue remains on the adhered surface
•The adhered surface absorbs the color of the label
•The adhered surface is damaged
We shall not be liable for any damages, losses, costs, or expenses
arising from these problems.
Check

Introduction 5
Precautions when using tape cartridges
Precautions when installing tape cartridges
■Tighten the ink ribbon
Insert a pencil or a similar tool into the hole of the tape cartridge and
turn it slightly toward the direction of the arrow. If the ink ribbon is not
tightened, it may come in contact with the printhead during installation.
This may bend or break the ink ribbon and damage the tape cartridge.
■Install the tape cartridge properly
Insert the tape cartridge fully with its label side
up until the cartridge is secured by the fixing
tab of the main unit. When installing a new tape
cartridge or one with an extended tape end,
straighten the tape end and pass it through the
tape guide. If the tape cartridge is not installed
properly, tape may be bent or the tape
cartridges may pop out of the main unit during
printing. This may cause damage or the
malfunction of the tape cartridge.
■Feed the tape after installation ( + )
After installing the tape cartridge, be sure to feed the tape by pressing the key and the
key at the same time. If the tape is not fed properly, tape may be bent or the tape
cartridges may pop out of the main unit during printing. This may cause damage or the
malfunction of the tape cartridge.
See "Feeding the tape" (p.24) .
■Do not drop or disassemble the tape cartridges. This may cause malfunction
of the cartridges.
■Do not pull or squeeze the label coming out of the exit slot. This may cause
malfunction of the device.
■Tape cartridges should be stored in a dark cold place away from direct
sunlight, heat, moisture, and dust. It is recommended that you use the tape
cartridge as soon as possible after opening.


6Introduction
General cautions
■Be sure to read and understand the "Important Safety Precautions" before using
your K-Sun®GREEN MACHINE®.
■Unplug the bundled AC adapter AST1116Y1-1 from both the device and the outlet after use.
This may prevent possible accidents caused by tripping over the cord.
■Do not store the device in direct sunlight, in places with dust or excessive humidity, or in
extreme temperatures.
■Do not attach labels on people, living things, public buildings or properties of others.
■Do not block or insert objects into the bundled AC adapter socket or the tape eject slot.
■Never touch the printhead.
■Be sure to use the tape cartridges that has "K-Sun®LABELShop®Tape Mark".
■Avoid using a tape cartridge with no remaining tapes or pressing without installing
tape cartridge. This may cause overheating and malfunction of the printhead.
■Always press + to feed the tape. Never pull out the tape forcibly, otherwise the
tape cartridge will be broken and unusable.
■Handle the tape cartridges with care, and avoid having impacts on them.
■Do not handle the keyboard roughly. Do not use a pencil or a sharp material to press the
keys. This may damage the keyboard.
■K-Sun®GREEN MACHINE®makes sounds when ejecting tapes. This is normal operation
for the device.
■Be careful not to cut yourself when using scissors.
■Do not insert labels that have no "K-Sun®LABELShop®Tape Mark" into the PeelGuard®.
■Be sure to turn the power off after use.
■Powering off message is displayed while turning off the K-Sun®GREEN MACHINE®. Do not
remove the AC adapter until the message disappear.
■Be sure to replace batteries with the power turned off. If you replace the batteries while the
K-Sun®GREEN MACHINE®is powered, files or data stored on it may be deleted.
■If your K-Sun®GREEN MACHINE®is not to be used for long periods, remove the batteries,
the bundled AC adapter, and tape cartridge from the main unit. K-Sun®GREEN
MACHINE®, batteries, the bundled AC adapter, and tape cartridges should be stored in a
dark cold place away from direct sunlight, excessive temperature and humidity, magnetism,
vibration and dust.
■If a battery is left inside the device for extended period of time, liquid from the battery may
leak. Follow the instructions given on the package of the battery and replace it before the
expiry date.
■Dispose of the used batteries according to the local regulations.
■Do not carry out any operations not described in this manual. It may cause injury or
damage to the device.
■Contents, specifications, and design described in this manual are subject to change without
prior notice.

Getting Started
This section describes how to connect the bundled AC adapter to your
K-SunGREEN MACHINE®and turn the power on. If you are a first time
user, it is recommended that you read this section first.

9Getting Started
K-Sun®GREEN MACHINE®Parts
Top side
Internal parts
Tape verification window
Display
PeelGuard®
PeelGuard®slot
PeelGuard®table
PeelGuard®guide
USB Connection for
PC models
Top cover
Fixing tab
Tape cartridge
case
Tape guide
Tape eject slot
Getting Started 9

Getting Started 10
Bottom
Printer Back
Battery cover
Battery case
Cable guide
AC adapter connector
PeelGuard®tray
10 Getting Started

11 Getting Started
K-Sun®GREEN MACHINE®Keys
(Print)
Prints the text you entered on the tape,
and cuts the tape automatically.
See p.37
+ (= Feed/Cut)
Feeds the tape 0.7", or cuts the tape.
See p.24
(Extra print)
Performs repeat printing, enlarge printing
or mirror printing. See p.79
+(= Print setting)
Sets the auto-cutter or the print density.
See p.86
(Graphic)
Shows the preview of the label by
scrolling the whole image.
See p.36
+ (=Preview)
Shows the preview of the printout.
(Telecom/Electrical Label Mode)
Enters the Telecom/Electrical Label Mode.
See p.52
(Language)
Specifies the language to be used for the
display.
See p.17
+(= English)
Switches the display language to
English.
(Edit)
Specifies Length, Frame & Table, Margin
and the other edit settings.
See p.59
+(= Condition)
Specifies battery type and the units to be
used for the display. Changes the stored
settings.
See p.101
The functions of each key are described below. To perform the operation indicated by
+ , hold down the key and press the specified key.
Getting Started 11

Getting Started 12
(Dark)
Adjusts the density level of the display.
See p.16
+ (= Density Reset)
Returns to the default setting.
(Size)
Specifies the line size.
See p.58
(Light)
Adjusts the density level of the display.
See p.16
+(= )
Turns on/off the back light.
See p.16
(Font)
Specifies the type of font.
See p.58
(Recall)
Recalls a stored file.
+(= File)
Stores text into a file.
See p.88
(Esc/Bs)
Deletes the text to the left of the cursor.
Cancels the current operation.
See p.43
+ (= Delete)
Deletes the texts or the paragraphs.
See p.43
(Sequence)
Enters sequence numbers.
See p.74
+ (= Barcode)
Enters barcode.
See p.76
(Symbol)
See p.34
+ (= Pictograph)
See p.34
(Return)
+ (=New Paragraph)
Starts a new paragraph.
See p.46.
Character keys
( ...)
Enters text.
See p.32.
Hold down the and press the
function keys to activate the functions
written on the upper part of the keys. To
enter in small letters or some symbols,
hold down the and press the
character keys.
(ON, OFF)
Turns on/off the power.
See
p.23.
(PC link)
Switches the status so that the K-Sun®
GREEN MACHINE
®
can be connected
to a computer.
(Caps lock)
Enters texts in capital letters.
See p.32
(Euro Latin)
Enters european or latin characters.
See p.33
(Space)
Inserts space.
12 Getting Started

13 Getting Started
(:<[{)
Enters symbols.
See p.35
+ (+-=|)
Enters symbols.
See p.35
(Cursor keys)
Moves the cursor or highlighted items to
up, down, right, or left.
See p.42
+ (= Cursor jump)
Moves the cursor directly to the
beginning of the paragraph/line or the
end of the paragraph/line. When
selecting items, shows the start or last
option.
See p.42
Getting Started 13

Getting Started 14
Display Indicators
Display indicators
<Text enter screen>
Line head icon
( ...)
Appears on the line head to show the
current line number. When there is a
text(s) to be printed on the label,
and appear on the line head.
is mean that you cannot print the
line.
See p.44
Confirmed texts (Example: 12AB)
Texts to be printed on the label.
Blinking character
When you press same button during
inputting the undefined characters, the
character candidate will be displayed in
turn.
The character of the blinking display is
not printed.
Text mode change icon ( )
Displayed when changing the character
mode such as font and decorate in the
line or paragraph.
See p.60
Cursor ( )
A movable indicator on a display,
marking the position at which a character
can be entered, corrected, or deleted.
See p.42
Memory full icon ( )
Appears when the maximum number of
letters (approx. 175 letters) are entered.
You cannot enter any letters until you
delete a part of or whole of the text.
Print information
Shows the tape width of the installed
cartridge and expected length of the
current label.
This information may not be displayed
depending on the settings.
See p.36
Print image
Shows the print image of the current
label. This information may not be
displayed depending on the settings.
See p.36
1
12AB
Caps
x.x
in
x/x
in
Auto Cut
7
6
5
4
3
2
1
Expand
Reduce
Euro Latin
2
12AB
14 Getting Started