K Tool International KTI-61076 User manual

KTI-61076/KTI-61077
3/4 TON UTILITY UNDER HOIST STAND
3/4 TON UTILITY UNDER HOIST STAND WITH PEDAL
OWNERS MANUAL
SPECIFICATIONS
KTI-61076 \ KTI-61077
Capacity ..............................................................................3/4 Ton
Lifting Height ............................................................53-1/2" - 80"
Base Dimension........................................................................12"
Shipping Weight...........33 Lbs. (KTI-61076), 37.45 Lbs. (KTI-61077)
KTI-61076 KTI-61077
Complies with ASME PASE/2014 Safety Standard
www.P65Warnings.ca.gov
Cancer and Reproductive Harm-WARNING:

KTI-61076/KTI-61077 2
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility
of the device owner to keep this manual intact and in a convenient location for all to see and read.
native language by the purchaser/owner or his designee, making sure that the operator comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of portable automotive lifting and support devices is subject to certain hazards that cannot be prevented by mechanical means,
but only by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the
proper use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly secured loads, overloading,
off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.
METHODS TO AVOID HAZARDOUS SITUATIONS
•Read, study, understand, and follow all instructions before operating this device.
•This stand is intended to assist in supporting under vehicle components, not the vehicle.
•dware
or components. Take corrective action before using the stand.
•Do not use beyond rated capacity. Do not shock load.
•Use only on a hard level surface.
•Wear eye protection that meets ANSI Z87.1 and OSHA standards (users and bystanders).
•Adequately support the vehicle before starting repairs.
•Center load on saddle. Do not use ends of saddle to support load.
•Be sure vehicle, vehicle component and stand are stable before performing any work.
•Failure to heed these warnings may result in personal injury and/or property damage.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS
SITUATIONS could cause accidents resulting in serious or fatal personal injury and/or property damage.
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
WARNING
WARNING
WARNING
WARNING
WARNING INFORMATION
shall be read to and discussed with the operator in the operator's

KTI-61076/KTI-61077 3
SETUP INSTRUCTIONS
This is the safety alert symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
Refer to parts breakdown on page 5:
1. Screw the post support in the round base.
2. Thread the large spin handle on the extension screw.
3. Install the bearing assembly in the receiver on top of the support tube.
4. Insert the extension screw assembly through the bearing and into the support tube until the underside of the spin handle rests on
the bearing assembly.
5. The model KTI-
washers and cotter pin provided.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Make sure the vehicle is properly supported, stable and at the required work height before positioning the stand(s) under the
vehicle component to be supported.
2. Consult the vehicle manufacturer for the proper handling of the component and use of under hoist stands.
3. Once the stand(s) has been positioned properly under the component, hold the stand's saddle in place with one hand while
turning the spin handle in a clockwise direction with the other hand. Remove the one hand from the stand's saddle when it comes
close to making contact with the component.
4. Continue turning the stand's spin handle in a clockwise direction until it applies pressure against the component. This pressure
should not exceed what is required to support the component. Excessive pressure might cause the vehicle or its component to
become unstable. Additional precaution should be taken when using a stand equipped with a foot pedal which can raise the stand's
saddle another inch more in height and produce as much as 400 pounds of force when depressed.
5. Before removing the stand from the component, make sure the component is securely fastened to the vehicle or properly
supported by another means. Removal of the stand can be accomplished by turning the spin handle in a counterclockwise
direction until the stand's saddle is clear of the component.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to
potential personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the stand in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust,
or any other harmful elements. The stand must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. Use a general purpose grease to lubricate the extension screw and foot pedal linkage if so equipped.
3. Every stand owner is responsible for keeping the stand labels clean and readable. Use a mild soap solution to wash external
surfaces of the stand.
4. Inspect the stand before each use. Do not use the stand if any component is cracked, broken or bent. Do not use the stand if it has
. Take corrective action before using the stand again. Premature
wearing or damage to components caused by loose or missing hardware is not eligible for warranty consideration.

KTI-61076/KTI-61077 4
WARRANTY
K-Tool International warrants that all jacks and service-related equipment will be free from defects in material and workmanship for a
period of 2 years following the original date of purchase. This warranty is extended to the original retail purchaser only. If any jack or
service-related item proves to be defective during this period, it will be replaced or repaired, at K-Tool International’s option, without
charge. This warranty does not apply to damage from accident, overload, misuse or abuse, nor does it apply to any equipment which
has been altered or used with special attachments other than those recommended.
K-Tool International HD and XD service-related equipment 2 Year Limited Warranty.
Michigan

KTI-61076/KTI-61077 5
3/4 TON UTILITY UNDER HOIST STAND
3/4 TON UTILITY UNDER HOIST STAND WITH PEDAL
PARTS BREAKDOWN
KTI-61076 \ KTI-61077
1
2
3
4
5
6
7
8
1 1
1 0
9
1 1
1 2
1 3
1 4
2
3
4
5
6
7
8
9
7
1 0
2
1
REF. # PART # DESCRIPTION QTY.
1 KTP6107601 Saddle Assembly 1
2 KTP6107602 Rubber Cover 2
3 KTP6107603 Spin Handle 1
4 KTP6107604 Bearing Assembly 1
5 KTP6107605 Post 1
6 KTP6107606 Connecting Rod 1
7 KTP6107607 Washer 2
8 KTP6107608 Clevis Pin 1
9 KTP6107609 Base 1
10 KTP6107610 R Pin 1
Also Available: Label Kit KTP61076LK
REF. # PART # DESCRIPTION QTY.
1 KTP6107601 Saddle Assembly 1
2 KTP6107602 Rubber Cover 2
3 KTP6107603 Spin Handle 1
4 KTP6107604 Bearing Assembly 1
5 KTP6107605 Post 1
6 KTP6107706 Pin 1
7 KTP6107707 Connecting Rod 1
8 KTP6107708 Foot Pump Assembly 1
9 KTP6107709 Clevis Pin 1
10 KTP6107710 Washer 2
11 KTP6107711 R Pin 1
12 KTP6107712 Cotter Pin 1
13 KTP6107713 Washer 1
14 KTP6107609 Base 1
Also Available: Label Kit KTP61077LK
KTI-61076 KTI-61077