KAEL Muhendislik Elektronik ENERGY 11-DIN User manual

KAEL Mühendislik Elektronik Tic. ve San. Ltd.Şti.
11-DIN
www.kael.com.tr
ENERGY 11-DIN 100a ENERGY
ENERGY-11-DIN 100A
ENERGY-11-DIN
■ ■ ■ ■
■ ■ ■ ■ ■
MODEL
PARAMETERS:
Ct : current transformer ratio (1...5000 )
Ut : voltage transformer ratio (1...4000 )
PULS oUt : Pulse out
CLr : clear
rES ALL PAr : reset all values
ENERGY-11- IN ENERGY-11- IN 100A
■
■
■
■
■
■
■
■
■
With 100A currrent tran former
■ LE display
■ IN ■ Current Transformer Ratio
■ 2 Pulse out for Energy
■ ■
■ ■
■
■
■
■
■
■
■ W Active Energy (import-export)
■
■
■ VAR Reactive Energy (import-export) ■ VA Apparent Energy
■
■ Voltage Transformer Ratio
■
Introduction
The device was designed to measure, report and analyse the electrical magnitudes in the 3-phase electric network and both design and software were
produced by KAEL engineers. The state-of-the-art technologies were inserted in this device and both menus which facilitate the use of the user and the
required features were included.
All the information and warnings you need to know concerning the device were described in the user operation manual. Please read this manual carefully
before engaging with the device. Please do not take any action before consulting with our company for any matters not clearly understood.
Tel: [phone] (pbx) Fax: [phone]
Factory: Atatürk Mh. 78. Sok. No:10 Ulucak Köyü Kemalpaşa İzmir- TURKIYE
1- The device shall be engaged by competent and licensed persons in conformity with the instructions set forth in the operation manual. In case required,
controls shall be carried out by such persons also.
2- o not open the inside of the device or cause to be opened. There are no parts inside the device which the user or anyone else may intervene.
3- Use the device according to assembly instructions
4- Before making electrical connection to the terminals of the device, make sure there is no electric power on the cables and terminals. The switchboard
shall not have electric power on.
5- The fuses used in the device are of 1A FF type.
6- Make sure to fix the device on the switchboard firmly without swings with the apparatus given with the device.
7- o not touch the keys on the front panel of the device with any substance other than your finger.
8- Wipe the device only with dry cloths after making sure the electric energy of the device is cut-off. Water or chemicals used for cleaning may cause
damage to the device.
9- Before activating (energizing) your device please make sure that the terminal connections are made according to the connection scheme and without
causing any contact problems (loose connection or contact of multiple copper cables).
10. The above measurements and warnings are for your safety. Kael Elektronik Ltd Şti or the dealer may not be held liable for any inconveniences when
those warnings are not observed.
WARNINGS
■ Easy use with menu
■ Improved dynamic software
■ Ability to enter current and voltage transformer rates
■ True RMS
■ Password protection
Feature
Measurements Outputs
■ Pulse Output ( 2pcs)
■ Active Energy (ΣkWh)
■ Inductive Reactive Energy (ΣkVARh(ind) )
■ Capacitive Reactive Energy (ΣkVARh(cap) )
■ Apparent Power (ΣkSh)
■
■
■
■
■ IN

L3 (T)
L2 (S)
L1 (R)
N
lL3
lL2
lL1
max.
demand
Pulse
Reac.
(C
ENERGY-11-DIN
Output Pulses
20 21 22
C1 O1 O2
▼▼ ▼
N L1 L2 L3
k1
l1
k2
l2
k3
l3
230 Vac
50-60Hz
Voltage Inputs
0 – 500 Vac Current Inputs
X/5 A
▲▲▲▲
Power
Supply
▲ ▲
L3 (T)
L2 (S)
L1 (R)
N
max.
demand
Pulse
Reac.
(C
ENERGY-11-DIN100A
Output Pulses
20 21 22
C1 O1 O2
▼▼ ▼
N L1 L2 L3
k1
l1
k2
l2
k3
l3
230 Vac
50-60Hz
Voltage Inputs
0 – 500 Vac Current Inputs
100 A
▲▲▲▲
Power
Supply
▲ ▲
load
With 100A current transformers
Act 0039230.0
W VAR VA Hr
K
G
MAct - 0000000.0
W VAR VA Hr
K
G
M
imp exp ∑ imp exp ∑
Total import Active Energy Total export Active Energy
MEASUREMENTS
SET SET
pos 0009230.0
W VAR VA Hr
K
G
Mneg - 0000065.3
W VAR VA Hr
K
G
M
imp exp ∑ imp exp ∑
Reactive Energy (KVARhr,MVARhr,GVARhr)
Total import/export positive and negative energy can be monitored .
Energies can be deleted in (CLR Energy) menu.
Total import positive Reactive Energy Total import negative Reactive Energy
SET SET
pos 0000000.0
W VAR VA Hr
K
G
Mneg - 0000000.0
W VAR VA Hr
K
G
M
imp exp ∑ imp exp ∑
Total export positive Reactive Energy Total export negative Reactive Energy
SET SET
App= 0039230.0
W VAR VA Hr
K
G
M
imp exp ∑
Total Apparent Energy
Apparent Energy (KVAhr)
Apparent Energy can be deleted in (CLR Energy) menu.
K
G
M
Act 0039230.0
Act 0039230.0
W VAR VA Hr
imp exp ∑
K
G
M
Act 0039230.0
Act 0039230.0
W VAR VA Hr
imp exp ∑
■ The connections of the system must be made when it is out of power.
■ The connections of the device shall be connected as shown in the connection scheme.
■ The current and voltage connections shall be connected in a manner that they are placed on the same phase same current transformer and with the same
direction. Connection scheme must be observed.
■ The value of the current transformer chosen shall not be less than the real load value and X/5 amperes. Moreover, it is recommended to chose class 0,5.
■ Fuses to be used shall be FF type. Fuses to be used shall be chosen according to given current values.
■ o not supply power to the device before all the connections are checked by means of a measurement apparatus.
■ The terminals for currents and voltage are suitable for cables with 2,5mm2 cross- section.
■ Pulse outputs terminals are suitable to max. 1,5 mm2 cables
Making the Connections
load
MEASUREMENTS:
(P.F, W, VAr, VA, ΣW, ΣVAR, ΣVA, ΣWh, ΣVArh, ΣVAh
The above parameters can be reached step by step using arrow keys. Related leds lights up and displays the
corresponding parameter value which is displayed at the same time.
Active Energy (KWhr,MWhr,GWhr)
Total import and export active energy can be monitored. Energies can be deleted in (CLR Energy) menu.
Total import Active Energy

SET
Ct rate
SET button is pressed for 3 seconds
SET
increase
decrease
▲
▼
SET
▲
▼
▲▼
▲▼
SET
▲
▼
Parameters
ut rateut rateut rate
PULS OUT
0001
0001.0
PULSOUT1
▼
▼
▲
▲
PULSOUT2
Ct Current Transformer Ratio ( 1........5000 Current transformer ratio value
is entered.Example: For 500 / 5A is entered 100. (500/5A=100
Ut Voltage Transformer Ratio ( 1........4000 Voltage transformer ratio value is
entered.Example: For 34500 /100V is entered 345. (34500/100V=345
Puls out The device has two digital pulse output. Menus and functions are the
same for the two outputs.Outputs can be set differently according to the type of
the desired energy
cLr delete
rES ALL PAr All parameters are erased and factory settings are restored
quit quit from parameter menu
max.30Vdc
C
O1
O2
t (ms
t (ms
Pd
Pt Pt Pt
Pd
Pd
Energy
5 – 24V
Max 30V Pp Pp
1. puls out
NOTE: If one of the three parameters P,Q,S is activated,
the other two parameter will not appear in the setting menu.
You can access to the other parameters menus only if they
are all deactivated.
max.30Vdc
C
O1
O2
+-
usage with relay
Connection to another device as insulated
+-
SET
PULSOUT1 p
PULSOUT1 Q
PULSOUT1 s
▼
▼
▲
▲
▲
▲▼ ▼
▲
▲
▲
▲
SET pu stype
pu sdea
Pu s per
▼
▼
▲
▲
▼
▼
▲
▲
SET
pu stıme
quıt
▲
▲▼ ▼
▲
▲
▲
▲
▲
▲▼ ▼
▲
▲
▲
▲
▲
▲
▲
▲
SET
SET
SET
pu stype
pu sdea
Pu s per
▼
▼
▲
▲
▼
▼
pu stıme
▲
▲▼ ▼
▲
▲
▲
▲▼ ▼
▲
▲
▲
▲
pu stype
pu sdea
Pu s per
▼
▼
▲
▲
▼
▼
pu stıme
▲
▲▼ ▼
▲
▲
▲
▲▼ ▼
▲
▲
▲
▲
pu stype
pu sdea
Pu s per
▼
▼
▲
▲
▼
▼
pu stıme
▲
▲▼ ▼
▲
▲
▲
▲▼ ▼
▲
▲
▲
▲
pu stype
pu sdea
Pu s per
pu stıme
off
0.1
50
50
SET
▼
▼
▲
▲
▼
▼
▲
▲
▼
▼
▲
▲
▼
▼
▲
▲
Pul e Type (PULS tyPE) :
For Reactive Energy, it can be
selected as import(ind)-import(kap)
-export(ind) -export(kap)-OFF
Pp (PULS PEr): Pulse delay time
It can be selected between 50ms – 900 ms
Pt (PULS tınE) :
Pulse Time It can be selected between
50ms – 900 ms
Pd (PULS dEAL) : 1
The amount of energy equivalent to Pulse.
It can be selected between 0,1kWh – 10MWh
2. puls out
Active energy settings
Reactive
energy
settings
Apparent
energy
settings
increase
decrease
increase
decrease
SET button is pressed for 3 seconds, the parameter menu can be accessed. First parameter is current transformer ratio. After pressing
the SET key, value is increased or decreased by using the arrow keys. By pressing the SET button, the new value will be saved.
Pul e Type (PULS tyPE) :
For Active Energy, it can be
selected as import-export-OFF
when amount of each energy (Pd) occurs ,
a pulse is generated from output, during time of (Pt).
And then, output stays as 0V ,during time of (Pp)

cLr :Accumulated energie can be era ed in thi ection.
The parameter which indicated by the LED at the top of the device, will be
era ed.
▲▼
SET
▲
▼
▲▼
SET
▲
▼
▲▼
SET
▲
▲▼
Exit Menu
CLR
RES ALL PAR
QUIT
CLR ENERGY
YES rES ALL PAr : All parameters are erased and factory settings are restored
increase
decrease
increase
decrease
Operating Voltage (Un) : (Phase-Neutral ) 230Vac
Operating Range : (0,8-1,1) x Un
Operating Frequency : 50/60 Hz
Supply Power Consumption: < 6VA
Power Consumption
of Measurement Inputs: : < 1VA
Vin : 1 – 300 Vac (L-N)
: 2 – 600 Vac (L-L)
Iin : (as the secondary current of
the current transformer)
0,01 - 6 Amp AC
Measurement Class : CAT III
Voltage Transformer Ratio: : 1 ..... 4000
Current Transformer Ratio : 1 ..... 5000 (25000/5A)
Connection Type : 3P&4W , 3P&3W , ARON
emand Time : 1 – 600 min
isplay range : 1,0V - 400,0 kV
: 0,001A ........ 25000 A
: 0 – 999,9 M (W,VAR,VA)
: 0 – 999,9 k (W,VAR,VA)
: 0 – 999.999.999,999 (GWh,GVARh,GVAh)
accuracy
Active Power : 1 class
Reactive Power : 2 class
Apparent Power : 1 class
Pul e Output (2 pcs)
Operating Voltage : 5 – 24Vdc max. 30Vdc
Operating Current : max 50 mA
Min. Switching Time : 100 ms
Technical Specification
evice Protection Class : IP 20
Terminal protection class : IP 00
Ambient temperature : - 5 °C .... + 50 °C
Installation Type : IN rail
imensions : 105x90x59 mm
NOTE: Operating Voltage (Un): ask price and delivery time for 85-256Vac/dc
N
1Σ
N
Pi
i=0
P
=
N
1Σ
N
Qi
i=0
Q
=
S = P 2Q2 +
PF = P
S
Active Power
Reactive Power
Apparent Power
Power Factor
Formula
Current Transformer(Primary) Value : 5 / 5 A
Voltage Transformer Ratio : 1
Pulse Type for 1.Pulse Output : OFF
Pulse Value for 1. Pulse Output (Pd) : 1 KWh
Pulse uration for 1.Pulse Output (Pt) : 100 ms
Pulse OFF Time for 1.Pulse output (Pp) : 200 ms
Pulse Type for 2.Pulse Output : OFF
Pulse Value for 2. Pulse Output (Pd) : 1 KVARh
Pulse uration for 2.Pulse Output (Pt) : 100 ms
Pulse OFF Time for 2.Pulse output (Pp) : 200 ms
Factory Settings
1. Pulse ouputt2. Pulse output
Note :When factory settings
are restored, energies are set to zero.