Kaipule IX32 Zwave User manual

3.安装
3.1 安装注意事项：
不要对着冷热源；
不能对着太阳光；
不能跟高压线安装在一起；
不能安装在基础不牢固的地方。
1.简介
IX 32-Zwave无线吸顶式被动红外入侵探测器是采用能量堆
积逻辑处理、随机动态时间分割术的数码微处理控制入侵
探测器。IX32-Zwave产品的被动红外部分采用精密球面菲
涅尔透镜，提高能量接收的效率，灵敏度高，误报率极低
。配合先进的专利软件技术能使其对真正的入侵者、或者
是其它可能引起误报的干扰因素，作出准确的判断。具有
超高的探测和防误报性能。探测脉冲数可选,能完全应用于
各种室内场合，排除种种普通室内探测器无法克服的误报
、漏报，性能远远超出其它普通的红外入侵探测器。内置
大容量电池，独有的省电模式，电池使用时间长达三年以
上。
2.规格
型号： IX 32 - Zwave
探测距离：6m@25℃
发射距离：室内直线距离≤30m
输入电压：3VDC
消耗电流：≤16μA（待机） ≤35mA（报警）
光学透镜数据资料
红外区域：12+12+6
最大覆盖面积：直径6米
发射频率：868.4MHz/908.4MHz
警报指示：LED指示灯亮 ≤1秒
安装方式：吸顶式安装
安装高度：2.5～4.0米
工作温度：-20℃～50℃
保存温度：-20℃～60℃
外观尺寸:（长*宽*高）100*100*33.5毫米
探测区域
(如右图所示)
3.2 跳针设置说明
IX32可设置以下三种工作模式：
测试模式：探测器被触发后，间隔5秒以上才能再次被触
发报警。触发后至少间隔30s后会发送消警信号给对应设
备。
节能模式：探测器被触发后，间隔3分钟以上才能再次被
触发报警。触发后至少间隔3分钟后会发送消警信号给对
应设备。
对码模式：无任何功能。
IX30可选择以下三种脉冲：
一个脉冲：探测器检测到一个脉冲信号就报警。
二个脉冲：探测器检测到两个脉冲信号就报警。
三个脉冲：探测器检测到三个脉冲信号就报警。
脉冲计数越高，灵敏度便会越低，但可以减少误报。
4.对覆盖区域进行步行测试
1，将探测器设置为测试模式，以便进行步行测试。脉冲
计数设置按需要设置为1,2或3。
2，在覆盖区域的远端从任意方向以每秒一步（约0.75m/s
的速度，在探测范围内作横向移动，会引发LED指示灯点
亮1秒钟，即产生报警（如右图）。
3，从相反方向进行步测，以确定两边的周界。应使探测
中心指向被保护区的中心。
4，探测区中心不应向上倾斜。如果不能获得理想的探测
距离，则应上下调整探测范围，以确保探测器的指向不会
太高或太低。
5, 当调节了探测器的探测角度后，应按以上步骤重新进行
步行测试。
6, 步行测试合格后将测试模式调到正常模式。
5.IX32-Zwave操作说明
5.1. 无线网络登记/移除
a)网络登记： 用户启动主控网关登记状态后，在1.5 秒内
连续按三次按下防拆开关，可进行网络登记，网络登记过
程中产品内部红色LED 灯闪烁，登记结束LED 灯熄灭。
b) 网络移除： 用户启动主控网关移除状态后，在1.5 秒内
连续按三下防拆开关，可进行网络移除。
5.2. 红外报警
a) 本产品支持1 组状态报告，最多1个设备。产品报警时可
向已设定的组内设备报告门磁被触发时的状态。
5.3. 恢复出厂设置
在2.5s内连续按下防拆开关6次即可恢复出厂设置状态。
5.4. 手动唤醒操作
本产品为电池供电设备，网络登记完成后自动保持30 秒唤
醒状态以便接收主动唤醒参数，在1.5s 内连续按下三次防
拆按键，5 秒后自动发送唤醒命令。默认主动唤醒时间间
隔为1小时。
6.程序设定
a)红外状态回报：Binary Sensor Report
当传感器探测到有人入侵时，传感器会发出Binary Sensor
Report 指令给群组1 中的设备
[Command Class Notification，Notification Report,Alarm Type
= 0x07,Alarm Level = 0xFF, Notification Type = 0x07,
EVENT = 0x08]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0xFF,Type =0x0C(Motion)]
当传感器向关联组对应设备发送报警信号后，根据跳针设
置(见3.2说明)的时间间隔发送消警命令给关联组设备
[Command Class Notification，Notification Report, Alarm
Type = 0x07,Alarm Level = 0xFF,Notification Type =
0x07,EVENT = 0x07]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0x00,Type =0x0C(Motion)]
b)低电量回报：Battery Report
当传感器从睡眠状态被唤醒时，会检查门磁的电池状态，
当传感器检测到电池低压时，传感器每隔一个小时发出
Battery Report指令给群组1 中的设备。
[Command Class Battery, Battery Report, Battery Level = 0xFF(
低电量警告)]
注：低压发生后,设备会每隔1小时报告一次低压警告，同
时led短闪
c)破坏事件回报：Notification Report
当传感器上的防拆开关被拆动时传感器会发出Notification
Report 指令给群组1 中的设备
防拆闭合：
[Command Class Notification，Notification Report,Alarm Type
= 0x07,Alarm Level = 0xFF, Notification Type = 0x07,
EVENT = 00]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0x00,Type =0x08(Tamper)]
防拆拆动：
[Command Class Notification，Notification Report,Alarm Type
= 0x07,Alarm Level = 0xFF, Notification Type = 0x07,
EVENT = 0x03]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0xFF,Type =0x08(Tamper)]
Z-Wave 支持命令
Generic Deice Type =GENERIC_TYPE_SENSOR_BINARY
Specific Device Type =
SPECIFIC_TYPE_ROUTING_SENSOR_BINARY
Support Command Class =
COMMAND_CLASS_ASSOCIATION_V2,
COMMAND_CLASS_WAKE_UP_V2,
COMMAND_CLASS_BATTERY,
COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_ASSOCIATION_GRP_INFO,
COMMAND_CLASS_NOTIFICATION_V4,
COMMAND_CLASS_SENSOR_BINARY_V2,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2,
COMMAND_CLASS_VERSION_V2,
COMMAND_CLASS_BASIC,
COMMAND_CLASS_POWERLEVEL,
COMMAND_CLASS_DEVICE_RESET_LOCALLY
7.售后服务
我司产品的性能已经相当稳定，由于产品固有的低点传输
能力和有条件的使用范围。
其产品使用时仍会受到一定限制。下面列出一些可能出现
的情况：
1.室内环境限制，如同频干扰，通讯地理环境复杂等。
2.探测器电压不足等。
警告：若因客户擅自操作所引发的问题，我公司不承担保
修责任！
安装时，请勿倒置。建
议用户每周进行一次步
行测试。
IX32- Zwave 吸顶式被动红外入侵探测器说明书
1.Introduction
Kaipule’s IX32 Zwave Passive infrared intrusion detector takes
advantage of digital micro-control energy process anddynamic
random time division technology. By use of high precision
cylindrical Fresnel lens,increase its energyreceived efficiency.
High sensitivity and accuracy combined with advanced software
technology,make it moreeffectively detect true invader, or other
competitors that may cause false alarm. Excellent detective and
falselessperformance, optional pulse count, completely meets
various environments,reduce potential false alarm possibly,high
performance compared to other competitors, large capacity internal
battery.Exclusive power saved solution,it supports at least 2 years.
2.Product Specification
Model：IX32 Zwave
Detection distance：6m @ 25℃
RF：868.4MHZ/908.4MHZ
Sender distance：≤30m
Input voltage：3VDC
Consumption current：≤16μA（standby）
Sender current: ≤35m A（alarm）
Detection area as follows
Frensnel lens date sheet
Infrared area：12+12+6
Cover area：Diameter @ 6m
RF：868.4MHz/908.4MHz
Alarm indicator：LED indicator on less than 1 second
Installation method ：ceiling type
Mounting height：2.5m～4.0m（8.2～13.1feet）
Operating temperature：-20℃～50℃（-4℉～122℉）
Storage temperature：-20℃～60℃（-4℉～140℉）
Dimension:（L*W*H）100*100*33.5MM
3.Way To Install 3.2 Jumper Switch Function
IX32 can set following three working modes,
Testing mode：when the detector trigger, it will alarm again after
5seconds,It will send timeout signal to device related after trigger for
30seconds at least.
Energy-saving mode：when the detector trigger, it will alarm again
after 3minutes,It will send timeout signal to device related after
trigger for 3minutes at least.
Enrolling codes mode: No any functions
Position for jump pin,
IX32 can choose following three impulse：
One pulse: The detector gives an alarm when it checks one pulse.
Two pulse: The detector gives an alarm when it checks two pulses.
Three pulses: The detector gives an alarm when it checks three pulses.
The pulse count is higher and the sensitivity is lower, but can reduce
false alarm.
4. Walking Test In Detection Area
1. Set the detector to test mode to perform walking test. Pulse count
can be set by PULSE 1,2,3.
2. Walk breadthwise from any direction at the remote detection
coverage at the speed of 0.75m/s, then the LED indicator blinks for
several seconds and alarm triggered.
3.Test in different direction to confirm the two boundaries of
detection. Ensure the detector rightly points to the central detection
zone.
4. The center of detection zone should not uphill inclined. In order to
obtain a good detection range, please adjust the vertical detection
range, to ensure the detector is in right position.
5. Perform the walk test again as above when you have adjusted the
detection range.
6. When the detector passed the walking test, please adjust the test
mode to normal mode.
Please don’t invert the detector while installing. Here advice user to
have a walk test every week.
5.IX32-Zwave Operation System
5.1. Wireless Network Register/Remove
a) Network Register: when entering the register status of master
gateway, users can start the network register by continuously pressing
the anti-tamper switch 3 times within 1.5 seconds. The internal LED
blinks during registering, and off until finished register.
b) Network Remove: when entering the remove status of master
gateway, users can start the network register by continuously pressing
the anti-tamper switch 3 times within 1.5 seconds.
5.2.Wireless Detector Alarm
a) Supports one status report, one device; once triggered, it will send
status report to the devices in the set group.
5.3. Restore Factory Settings
Press the anti-tamper switch for 6 times within 2.5 seconds to restore
factory settings.
5.4. Operation Manual Wakeup
The detector is battery powered. After network register, it will keep in
wake-up state for 30 seconds in order to receive the parameters from
positive wakeup. Press the anti-tamper button 3 times within 1.5
seconds, detector will automatically send the wakeup command in 5
seconds. The positive wakeup interval is 1 hour by default.
6.Program Setting
a)Status：Binary Sensor Report
When detecting the intrusion, sensor will send Binary Sensor Report
command to the devices in group 1;
[Command Class Notification，Notification Report,Alarm Type =
0x07,Alarm Level = 0xFF, Notification Type = 0x07, EVENT = 0x08]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0xFF,Type =0x0C(Motion)]
After PIR detector sends alarm signal to device relevantly in the
associated group, it will send timeout command to devices in the
associated group according to the time in jumper settings(please refer
3.2).
[Command Class Notification，Notification Report, Alarm Type =
0x07,Alarm Level = 0xFF,Notification Type = 0x07,EVENT = 0x07]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0x00,Type =0x0C(Motion)]
b) Low Battery Report: Battery Report
When woken up from sleep mode, the sensor will check the detector’s
battery state.
Once low voltage, sensor will send Battery Report command to the
devices in Group 1 every hour.
[Command Class Battery, Battery Report, Battery Level = 0xFF(low
battery warning)]
Note: after low voltage, detector will send low voltage report every
hour, and LED blinks shortly.
c) Damage Report: Notification Report
When its tamper switch is opened, sensor will send Notification
Report command to the devices in Group 1
Tamper Close:
[Command Class Notification，Notification Report,Alarm Type =
0x07,Alarm Level = 0xFF, Notification Type = 0x07, EVENT = 00]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0x00,Type =0x08(Tamper)]
Tamper Open：
[Command Class Notification，Notification Report,Alarm Type =
0x07,Alarm Level = 0xFF,Notification Type = 0x07, EVENT = 0x03]
[Command Class Sensor Binary，Sensor Binary Report,Value =
0xFF,Type =0x08(Tamper)
Z-Wave supported command
Generic Deice Type =GENERIC_TYPE_SENSOR_BINARY
Specific Device Type =
SPECIFIC_TYPE_ROUTING_SENSOR_BINARY
Support Command Class =
COMMAND_CLASS_ASSOCIATION_V2,
COMMAND_CLASS_WAKE_UP_V2,
COMMAND_CLASS_BATTERY,
COMMAND_CLASS_ZWAVEPLUS_INFO_V2,
COMMAND_CLASS_ASSOCIATION_GRP_INFO,
COMMAND_CLASS_NOTIFICATION_V4,
COMMAND_CLASS_SENSOR_BINARY_V2,
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2,
COMMAND_CLASS_VERSION_V2,
COMMAND_CLASS_BASIC,
COMMAND_CLASS_POWERLEVEL,
COMMAND_CLASS_DEVICE_RESET_LOCALLY
7.Customer Service
Our made product are quite stable in performance, but as the product
itself transmission limited in bad circumstance and conditional
application, So it still has limited in usage. As the following
3.1 Installation Guide
Don’t face hot/cold source
Avoid direct sunshine
Wired detector should be away from high-pressure cable
Installation base should be stable
Installation base should not face to the metal wall
Indicator
Infrared Lens
Back Shell Front Case Battery Box
(2PCS)
Installing Location
Hanging Panel
Tamper Switch
Jumper Setting
IX 32- Zwave Passive Infrared Intrusion Detector
Manual(Ceiling Type)
Max.6m
Side-looking Down-looking
Detection Range
m
2,Turn over the alarm,anti-clock
wisely rotate the hanging panel,
and remove it.
3,Insert 2 pcs#5 battery in
right polarity.
1,Take the screw,
expansive tube
and 2 pcs #5 battery.
screw
expansive tube
battery
5,Hold the device in ordinary
grip,let the back hole face to
raised part of the panel to
install,then clock wisely whirl
it the bottom,so the device can be
fixed.
Clockwisely Rotation
Upward Installation
4,Make location hole as picture
indicates,knock the expansive
tube in it,use screw knife to make
the screws entering.then the
panel can fix on the wall.
Underline
and make holes
Insert tubes
Fix the panel
3 pulses
2 pulses
1 pulse（default）
Test Mode
Power Save Mode（default）
Code Mode
Pulse Count
Working Mode
Tamper Switch
3.
situations:
1.Indoor environmental restrictions, such as co-frequency interference,
complicated geographical environment of communication etc.
2. Detector power low voltage ,etc.
Warning: If the problems caused by user’s incorrect operation, our
company will not be responsible to it!
1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9
英文双面
中文双面