Kaiser Baas GAMMA User manual

GAMMA DRONE
USER GUIDE

Join the social movement and follow us on
Share your footage with us on our social media
#ChallengeYourself
Need help? www.kaiserbaas.com/support
To view the entire Kaiser Baas product
range and accessories visit:
www.kaiserbaas.com

TABLE OF CONTENTS
Disclaimers And Warnings 6
Safety Warnings and Operating Guidelines 7
Gamma Drone Features 8
Key Features 8
Included Equipment 9
Drone Specications 10
Transmitter Specications 11
Battery Guide 12
Battery Charging 13
Drone Setup/Installation 14
Drone/Transmitter Binding 16
Drone Calibration 16
Drone Trimming 17
Pre-ight Checklist 17
Flight Operation Guide 18
Take-O and Landing Basics 19
Flight Modes 20
Obstacle Avoidance 21
360° Flips 22
Return Mode 22
Headless Mode 23
WiFi App Operation 24
WiFi Drone Operation 26
Specications 27
FAQ 29
Contact Us 30

EN
GAMMA DRONE | User Guide
6
DISCLAIMERS AND WARNINGS
Please read this section carefully before using your Kaiser Baas Gamma Drone.
By operating this product, you hereby agree to these disclaimers and signify that you
have read and understood the warnings and conditions fully.
THIS PRODUCT IS NOT SUITABLE FOR PEOPLE UNDER THE AGE OF 18.
Always observe the safe flying instructions within this User Guide, as well as the guidelines
and regulations of your local aviation authorities.
Above all, maintain a safe distance from people and property when operating your
Gamma Drone – a safe distance of 10m is recommended.
Kaiser Baas accepts no liability for damage(s) or injuries incurred directly or indirectly
from the use of this product, including but not limited to the following conditions:
• Failure to follow the full instructions and cautions in the User Guide, pertaining to
correct assembly and safe operation.
• Damage(s) or injuries caused by erratic operation or poor piloting decisions.
• Damage(s) or injuries caused by mechanical failures as a result of neglect, including the
erosion and aging of product components.
• Damage(s) or injuries caused by the Drone being own in the following conditions:
• Unfavourable lighting; where the Pilot’s ability to see the Drone clearly is diminished.
• Inclement weather; moderate to high winds, rain, snow or hail.
• Flying near electrical hazards, such as power lines or towers.
• Flying in or near re, oods, tsunamis, ice, avalanche, landslide, earthquake, etc.
• Damage(s) or injuries incurred due to users under the inuence of drugs or alcohol,
suering dizziness, fatigue, nausea and any other condition; physical or mental that
could impair the Pilot’s ability to y responsibly and within the boundaries of the law.
• Damage(s) or injuries caused by malfunctions or “hacks”, rets or the replacement of
original components with non-Kaiser Baas provided accessories and/or parts.
• Damage(s) or injuries caused by the misuse or incorrect operation of the battery,
protection circuits, Transmitter or Battery Charger.
• Damage(s) or injuries caused by ying the Drone in abnormal conditions and allowing
external substances to come into contact with the Drone e.g. water, oil, soil, sand or any
other material that could enter the Drone and its internal compartments, including the
battery.
• Damage(s) or injuries caused by ying in areas such as those with: magnetic interference,
radio interference, government regulated no-y zones or airports.
• Any other losses that are not covered by the scope of Kaiser Baas liability.
Kaiser Baas reserves the right to make changes to this User Guide if required. Please
check the Kaiser Baas website for the most up to date version of this guide:
www.kaiserbaas.com/support
The information within this manual is subject to change without notice.

EN
GAMMA DRONE | User Guide
7
SAFETY WARNINGS AND OPERATING GUIDELINES
Even though the Gamma Drone may look small and light, there are important safety
considerations to bear in mind when operating this device. Always observe the following
guidelines:
• DO NOT y the Drone within 10m of people anywhere. Consider your personal liability
when you choose to operate your Drone.
• DO NOT attempt to handle or catch the Drone while it is in operation.
• DO NOT attempt to handle the Drone while the Rotor Blades are still spinning.
• DO NOT allow others to approach the Drone while it is in operation and the Rotor
Blades are in motion.
• Always make sure that you have completely “disarmed” the Drone before handling.
• Always maintain Visual Line-of-Sight (VLOS) with the Drone.
• Always y between ocial sunrise and ocial sunset, local time.
• Never engage in careless or reckless manoeuvres. Consider the impact reckless
behaviour might have on other Drone enthusiasts and future Pilots.
• Never operate your Drone when intoxicated or when you are incapacitated in any
other way.
• Always follow your local aviation authority’s guidelines.

EN
GAMMA DRONE | User Guide
8
GAMMA DRONE FEATURES
The Gamma Drone is an easy to fly Quadcopter that is suitable for both new Pilots and
experienced flyers alike. It provides excellent self-levelling and altitude-holding and you
will find this takes the stress out of Drone piloting.
If you are new to the fun of flying drones, you can expect to be up and flying in a short
time. Of course you need to familiarize yourself with the safety, operating and controls
of the Gamma Drone first! Give yourself time to become accustomed to the feel of the
Drone and eect of the controls.
The Gamma Drone can be used with its camera or transmitter in the following
configurations.
• Drone and Transmitter (No FPV)
• Drone, FPV App and Transmitter
• Drone, FPV App and Smartphone Control
For reference on how to use the FPV and Smartphone Control Modes please refer to the
WiFi App Operation section of this user guide.
KEY FEATURES
• Altitude Hold
• Obstacle Avoidance Module
• 720p HD Video/Photo Camera
• Live FPV and Recording with Smartphone App
• Cartridge Battery System
• One-Key Takeo/Landing
• One-Key Return Function
• Headless Mode
• 360° Flips
• 90° Adjustable Camera Pivot
• Cartridge Camera System
• 6.5 mins Flight Time
• Up To 30 meter FPV Range
• 90mins Battery Fast Charge
• Rechargeable Remote Transmitter

EN
GAMMA DRONE | User Guide
9
INCLUDED EQUIPMENT
A Gamma Drone E4 Spare Blades
B 720p WiFi Camera FScrewdriver
CBattery GRotor Blade Guards
DBattery/Remote USB Charging Cable HObstacle Avoidance
A
D
B
E
G H
C
F

EN
GAMMA DRONE | User Guide
10
DRONE SPECIFICATIONS
A
B
D
E
F
H
I
G
C
A Gamma Drone FMotor
B Rotor Blade G Obstacle Avoidance Module
CPower Button HLanding Gear
DCamera Module IRotor Blade Guards
EBattery Module

EN
GAMMA DRONE | User Guide
11
TRANSMITTER SPECIFICATIONS
S
T
Q
R
A Charging Indicator KPitch Backward Trim
B Throttle/Yaw Left Stick L Pitch Forward Trim
CYaw Left/Right Trim MRoll Left/Right Trim
DPower Switch NInvert Throttle/Rudder Sticks
(Hold button before switching transmitter on.
The transmitter will confirm with a long beep.)
ECamera Lens Up OPitch/Roll Right Stick
FCamera Lens Down PPower LED Indicator
G360° Flip QOne Key Launch/Auto Land
(Long Press 3 Seconds to STOP)
HCharge Socket RSpeed Mode Switch
IHeadless Mode SPhoto/Video Button
(Click once for Photo/Long Press to record video
– Only for Non-WiFi Camera Modules)
JLED Toggle TReturn Toggle
A
B
D
F
H
I
J
N
O
P
M
K
L
E
G
C

EN
GAMMA DRONE | User Guide
12
BATTERY GUIDE
It is imperative that only a Kaiser Baas Gamma Drone Battery is used inside the Gamma
Drone.
DO NOT use any third-party or unknown accessories or batteries.
Always ensure your Drone battery is charged before ight.
Battery Safety Warnings:
• DO NOT disassemble the battery.
• DO NOT short-circuit the battery.
• DO NOT ever poke or puncture the battery with any blunt or sharp instrument.
WARNING There is a high risk of it igniting!
• DO NOT ever leave the battery near an open ame or heat source.
• DO NOT immerse the battery in water.
• DO NOT charge the battery in direct sunlight.
• Never leave a charging battery unattended.
• Only remove the battery from its supplied charger when the charging cycle is complete.
• DO NOT reverse charge or over-charge the battery.
• Always charge the battery in a designated space, away from people and animals.
• If the battery becomes bloated or appears to be inated - DISCARD THE BATTERY
IMMEDIATELY – Instructions: place the bloated battery in a bucket lled with salt
water (200 grams salt to 1 Litre water) and leave the battery in the solution for three
days. You may now dispose of the battery through your local recycling center. Never
use your battery after conducting the discard process.
• If the battery has a high surface temperature, leave it to cool before you try to re-
charge it.
• Always ensure the battery is free from all damage and deformation before use.
• If you see any sign of smoke coming from the Drone or battery area - STOP OPERATING
IMMEDIATELY – when safe, disconnect and remove the drone battery.
• DO NOT use the battery with unspecied equipment.
• DO NOT touch a leaking battery directly. Never let battery contents touch your skin or
clothing. If contact occurs, seek medical advice immediately.
• DO NOT throw or cause any trauma to the battery.
• DO NOT put the battery in a microwave or high pressure container.
• DO NOT charge the battery if the ambient temperature is below 0°C or above 45°C.
• Always use the supplied charger and observe charging requirements.
• Always store the battery in a safe and cool place and never store the battery fully
charged.

EN
GAMMA DRONE | User Guide
13
BATTERY CHARGING
To charge the Drone Battery:
1. Remove the battery from the Drone by pressing the clip and sliding it out of the Drone
battery compartment.
2. Connect the USB Charging Cable to the Battery Pin terminal located on the battery.
3. Connect the USB Charging Cable to an electronic device.
Note: If using a wall charger, ensure that it is a certified product for your region.
AC Input: 100-240VAC 50/60Hz. DC Output: 5VDC 0.5A/1A/2.1A. Only use a USB
charger with suitable approval and certification. Do not charge in conditions outside
of the 10°C-45°C range.
4. The USB Charging Cable features a red LED indicator light that will turn on when
Charging is complete or there is no battery connected. While it is charging the light
will be OFF.
5. A full charge cycle will take approximately 90mins by 0.5A/1A/2.1A charger.
To charge the Transmitter:
1. Connect the USB Charging Cable to the Remote Transmitter
2. Connect the USB Charging Cable to an electronic device.
3. Note: If using a wall charger, ensure that it is a certied product for your region. AC
Input: 100-240VAC 50/60Hz. DC Output: 5VDC 0.5A/1A/2.1A Only use a USB charger
with suitable approval and certication. Do not charge in conditions outside of the
10°C-45°C range.
4.The USB Charging Cable features a red LED indicator light that will turn on when
Charging is complete or there is no battery connected. While it is charging the light
will be OFF.
5. The Transmitter green LED indicator will be ON while it is charging. It will turn OFF
and the red LED indicator will switch on when complete.
Low Battery
The Drone LED Lights will flash when the drone is in Low Power Mode. When the LEDs are
flashing you should bring the Drone to a complete stop. Failure to note the Low Battery
signal may cause a sudden loss of power endangering Persons, Property and the Drone.
Running the Battery completely flat will impact the health and future flight time of your
Drone.

EN
GAMMA DRONE | User Guide
14
DRONE SETUP/INSTALLATION
Ensure the Drone is OFF prior to installation of modules.
Camera Assembly:
1. Insert the Camera Module into the front empty slot of the Drone. The Camera Module
will click into place.
2. Refer to the camera section for instruction on how to use
Battery Assembly:
1. Insert the Battery Module into the rear empty slot of the Drone. The Battery Module
will click into place.

EN
GAMMA DRONE | User Guide
15
Obstacle Avoidance Assembly:
1. Match the Obstacle Avoidance Module to the bottom of the Drone
2. Push and slide the Module according to the diagram. The Module will click into place.
3. Refer to the ight modes section for further instruction.
Rotor Blades Assembly:
It is important that only Kaiser Baas Gamma Drone Rotor Blades are fitted to the Gamma
Drone. Never use any third party accessories or tools.
Your Drone will come ready to fly with Rotor Blades attached. If you need to replace
them, please refer to the following guide:
Disassembly:
1. Use the provided screwdriver to untighten the
screw in an anti-clockwise direction.
2. Remove the Rotor Blade by pulling up and o
the motor axis bar.
Assembly:
1. Insert the Rotor Blade onto the motor axis bar.
2. Only install the Rotor Blades to the corresponding
clockwise/anti-clockwise motor. A letter is
marked on each blade to indicate which motor
it should go on. Incorrect installation will cause
severe instability. Refer to the diagram
3. Use the provided screwdriver to tighten the
screws in a clockwise direction.
[WARNING] Never use Rotor Blades with any
signs of damage or wear and tear. This includes
chips, scratches and cracks. Damaged Rotor
Blades can cause the Drone to fail in-flight and
may result in damage to persons or property.
[WARNING] Never touch the Drone or the Rotor
Blades when the motors are spinning.

EN
GAMMA DRONE | User Guide
16
DRONE/TRANSMITTER BINDING
To operate your Drone, you must rst bind the Drone to your Transmitter before every
ight.
Ensure your Drone and Transmitter are fully charged and follow these steps in order:
1. Turn on your Drone by holding the power button for 1.5 seconds.
2. The Drone lights will ash indicating it is ready to bind to a Transmitter.
3. Turn on the Transmitter.
4.Using the Left Throttle/Yaw Stick move it to the maximum UP position and return it
back to the zero position.
Note: you must complete this process within 5 seconds of powering on the
Transmitter or you will have to restart the process.
5. The Drone LED lights will stop ashing indicating the Drone is now paired to the
Transmitter.
DRONE CALIBRATION
Before every ight it is important to calibrate your Drone.
Calibration ensures the Gyroscopes are reset and the Drones Direction/Heading is xed.
Always calibrate with the Drone and the Pilot facing the same direction.
Calibration:
1. Place the Drone on level ground facing the same direction as the pilot.
2. Push the Left Throttle/Yaw Stick and the Right Pitch/Roll Stick to the bottom left and
hold for 2 seconds until you see the LED indicator lights on the drone start to ash
rapidly.
3. Release the sticks and wait for the drone LEDs to stop ashing.
4.The Drone LEDs will stop ashing indicating that the calibration has been completed.
1 2

EN
GAMMA DRONE | User Guide
17
DRONE TRIMMING
Control of the Drone can be trimmed using the trim buttons on the Transmitter. If the Drone
is drifting o during a hover or other ight maneuver, these buttons are used to counter
this drift.
To reset all trimming, simply land the Drone and re-calibrate.
PRE-FLIGHT CHECKLIST
• Do a COMPLETE check of your surroundings; look for hazards above, in front and
behind you.
• Be especially aware of things like power lines and nearby people and animals. If these
hazards exist, DO NOT deploy your Drone and consider a new Take-o Location.
• DO NOT FLY in inclement weather or moderate to high winds.
• DO NOT FLY in populated areas as unforeseen ight hazards may occur.
• Remember YOU are the Pilot. Safety is YOUR responsibility.
• DO NOT FLY near airports/controlled airspace. Ensure that you are at least 5.5kms
from any aireld and you are adhering to any regulations and laws laid out by your
local aviation authority. Remember checking your distance to these areas is YOUR
responsibility
• Never y your Drone near large crowds or above unwilling spectators.
• Make sure that you have the full permission of people within ying range of your
Gamma Drone and DO NOT y your Drone where people have not given permission or
have requested that you not y.
• Ensure the Drone is orientated in the desired direction.

EN
GAMMA DRONE | User Guide
18
FLIGHT OPERATION GUIDE
When operating the Drone, it is important for new Pilots to ensure that the Drone’s
heading is facing away from you.
The Transmitter has two control sticks, left stick (Throttle/Yaw) and right stick (Pitch/
Roll).
Left Stick
The Left Stick is known as the Throttle. This controls the Drone’s Elevation and Yaw.
Right Stick
The Right Stick is also known as the Elevator/Aileron. This controls the forwards and
backwards (Pitch) movement and the left and right (Roll) movement of the Drone.
(Throttle/Yaw) (Pitch/Roll)
Throttle Down
Throttle Up
Yaw Left
Yaw Right
Pitch Down
Pitch Up
Roll Left Roll Right

EN
GAMMA DRONE | User Guide
19
TAKE-OFF AND LANDING BASICS
To Take-O you must first bind the Drone to your Transmitter.
Refer to the Drone/Transmitter Binding Section.
The Gamma Drone comes equipped with a Take-O and Landing function.
To Take-O:
Press the Take-O/Landing Button to arm the Drone. The Rotor Blades will start to spin
indicating it is ready to fly. Push the Throttle/Yaw Left Stick slightly UP to fly.
The Gamma Drone features Auto-Hover, releasing the Throttle/Yaw stick will keep the
drone at the same altitude. Pushing the Throttle/Yaw Left Stick UP or DOWN will ascend
or descend the Drone respectively.
To Land:
Whilst the Drone is in flight press the Take-O/Landing button. The Drone will then
descend to the same altitude/level from which you armed it.
To Emergency Stop:
In an emergency in which you need to stop the Drone motors immediately, HOLD the
Take-O/Landing Button for 3 seconds to kill the motors completely.

EN
GAMMA DRONE | User Guide
20
FLIGHT MODES
The Drone features a number of Flight Modes and settings.
Speed Modes
There are 3 Speed modes on the Gamma Drone. They can be cycled through on the
transmitter by pressing the Speed Mode Button. Each mode is indicated by an increasing
series of beeps.
Mode 1-Beginner Mode
This is the default operating mode that the Gamma Drone initialises in. Please ensure that
you use this mode in a large open space with no obstacles. The sensitivity is very low and
is suitable for beginner pilots. It is less responsive and more forgiving.
Note: Obstacle Avoidance Module will only operate in this mode.
Mode 2-Intermediate Mode
To enable this mode, press the Speed Mode Button ONCE. The Transmitter will beep
twice indicating you are in Intermediate Mode. This mode is more responsive and flies
faster.
Mode 3-Pro Mode
To enable this mode, press the Speed Mode Button TWICE. The Transmitter will beep
three times indicating you are in Pro Mode. This is the most responsive and fastest mode
the Drone can operate in.
This is only recommended for pilots with experience flying the Drone.