KAM KWM6 User manual

KAM KWM6 & KWM11
VHF WIRELESS MICROPHONE KITS
INSTRUCTION MANUAL
KAM KWM6 & KWM11 VHF WIRELESS MICROPHONE KITS
MICROPHONE TRANSMITTER(s)
qPOWER ON / OFF SWITCH
wPOWER ON INDICATOR LIGHT
eLOW BATTERY INDICATOR LIGHT - when lit you have
approximately one hour left of useful operation. Ideally
change the battery when lit.
rMUTE / ON SWITCH - mutes the output of the mic when
switched to ‘mute’.
tBATTERY COVER - unscrews for access to the 9V
battery. IMPORTANT: Use Alkaline batteries only, Carbon-
Zinc and Zinc-Chloride batteries will not provide adequate
power and are not recommended.
USING THE KWM6 WIRELESS RECEIVER
The KWM6 uses a dynamic frequency switching system whereby it swaps between frequencies/antenna when in use to avoid interferance. This
process is fully automatic and does not require the user to make any adjustments.
1. Connect output to your mixer/amplifier, either A balanced XLR cable or an unbalanced, single conductor 1/4 inch jack plug cable.
2. Connect the AC adapter to the receiver and plug into an appropriate power outlet.
USING THE KWM11 WIRELESS RECEIVER
1. Connect outputs for channel A & B to your mixer/amplifier, either two balanced XLR cables for dual output or a single unbalanced 1/4 inch jack
plug cable for mixed output of both channels.
2. Connect the AC adapter to the receiver and plug into an appropriate power outlet.
USING THE WIRELESS MICROPHONE TRANSMITTER(S)
1. Slide the mic ON/OFF/STANDBY switch to the ON position.
2. Check the signal indicator is lit on your receiver to see if the radio signal is being received.
3. If the signal indicator is lit, begin singing or speaking.
4. During the performance, slide the ON/OFF/STANDBY switch to the STANDBY position when the mic is not being used.
5. When the performance is over, slide the ON/OFF/STANDBY switch to the OFF position to conserve battery power.
MICROPHONE BATTERY INSTALLATION
1. Slide the transmitter ON/OFF switch to the OFF position.
2. Unscrew the transmitter battery cover to expose the battery terminals.
3. Insert a fresh 9V Alkaline battery into the battery compartment. A fresh (new) battery should typically provide ten hours of performance time.
© COPYRIGHT LAMBA plc 2005. E&O E.
KWM6
RECEIVER
Front panel
Back panel
KWM11
RECEIVER
Front panel
Back panel
Kam KWM wireless mic kits are ideal for the
stage bound vocal performer who needs freedom
to roam with a quality of sound you’ll find hard to
beat for the price.
KWM6 WIRELESS RECEIVER
qPOWER INDICATOR
wSIGNAL INDICATORS
eOUTPUT LEVEL CONTROL
rBALANCED XLR OUTPUT SOCKET
tUNBALANCED JACK OUTPUT SOCKET
yDC POWER INPUT SOCKET
uPOWER ON SWITCH
iANTENNA A & B
KWM11 DUAL WIRELESS RECEIVER
qPOWER INDICATOR
wCHANNEL A SIGNAL INDICATOR
eCHANNEL B SIGNAL INDICATOR
rCHANNEL A OUTPUT LEVEL CONTROL
tCHANNEL B OUTPUT LEVEL CONTROL
yCHANNEL B BALANCED XLR OUTPUT SOCKET
uCHANNEL A BALANCED XLR OUTPUT SOCKET
iUNBALANCED MIXED JACK OUTPUT SOCKET
oDC POWER INPUT SOCKET
1) POWER ON SWITCH
1! ANTENNA A & B
MICROPHONE TRANSMITTER
qwe
r
t
y
u
ii
qwr
y
u
1! 1!
et
i
o
1)
e
qwrt
www.kam.co.uk
Kam KWM6-11 manual aw.qxd 31/8/05 3:33 pm Page 1