Sony ECM-Z200 User manual

‘ Canadian Model
AEP Model
SPECIFICATIONS
General
Type Electret condenser microphone
(with back-electret condenser
capsules)
Microphone output plug
L-shaped miniplug
Battery Size AA (IEC designation R6)
Dimensions Microphone head: 23 dia.x 125mm
(4.x 5 inches)
Microphone body:
28 x 56.5x 75mm (wih/d)
(14/, x 244,x 3 inches)
Weight Approx. 111g (3.90z)
Finish Matte black finish
Performance P
Frequency response
150 Hz- 15,000 Hz
Changeable (from uni-directiona!
to super cardioid characteristics)
Output impedance
Low impedance, unbalanced
Output level (deviation *3dB)
Open circuit voltage
-64.0dB (0.63mvV)*?
Directivity
Uni-directional
Super cardioid
characteristics
—§2.0dB (2.82 mV)
Effective output level
—44.9dBm *?
Uni-directional
Super cardioid
characteristics
*10dB =1V/Mybar, 1,000 Hz
. *2QdBm=1mW/0ybar, 1,000 Hz
Recommended load impedance is
more than 3kilonms.
—32.9dBm
MICROFILM
Power requirements
Normal operating voltage: 1.5V
Minimum operating voltage:
Approx. 1V
Current drain: Less than 1.5mA
(at normal operating voltage)
Battery life: Approx. 700 hours
with Sony SUM-3 (NS)
Maximum sound pressure input level *?
Uni-directional: More than 110dB
SPL
Super cardioid characteristics:
More than 100dB SPL (at
1,000 Hz, 1% distortion, 0dB
SPL =2x 10% bar)
*3 The mean value is taken and
converted to the equipment input
sound level.
Environmental temperatures
-20°C to +60°C (—4°F to +140°F)
for storage
0°C to +60°C (+32°F to +140°F)
for operation
UK Model
E Model
C—O
ELECTRET CONDENSER MICROPHONE
SONY.

ECM-Z200
1. DISASSEMBLY
Note: Follow the disassembly procedure in the numerical
order given.
Control board removal: @-@
Volume knob removal: @—-0, 6, @
Amp board removal: 0-9, 8
Remove
micro-|
control
board
phone case by
loosening lock
ring.
<
Se
7 | Remove control
board with
blade screw-
driver.
lock ring
microphone case
7)
control Bn OD LB}
|
Push from
the inside.
© Move control
knob fully in
the direction
of arrow.
back register (A)
microphone case
amp board
@ Remove amp board
by pulling lead
wires. slowly.
2. CAUTION ON REASSEMBLING
PC BOARD COVER
STICKING After roiling, fix with
the tape.
pe board cover
Wrapping finish amp board
point
amp board
Wrapping start point amp board
AMP BOARD POSITION SETTING
Set amp board into the microphone case by pushing
it vertically to the cutting point ( * ).
(See Fig. A.)
microphone case
amp board
— Fig. A—- amp board
BACK REGISTER (A) INSERTION
Be careful of the direction of back register (A).
; microphone case
back register (A}
lead wires from
amp board
back register (A) microphone case

ECM-Z200
CONTROL KNOB SETTING
Q Insert knob into case
as illustrated.
Q@-@
Set
control
knob
(See
Fig.
B).
@
Fix
control
board
tightly.
@
Fix
contro!
board
temporary
with
screw.
@
After
setting,
perform
operating
check
by
moving
control
knob
two
or
three
times.
WIRING
— Chassis —
to
battery
spring
—
Control
Board
—
shield BLK
double-sided
é
adhesive
tape
adhesive
tape
Guide
leads
in
the
groove.
to
chassis
to positive terminal board
3.
DIRECTIVITY
ADJUSTMENT
@
Connect
ECM-Z200
to.
the
microphone
input
Note:
This
adjustment
should
be
made
when
replacing
of
the
tape
recorder.
following
parts.
;
@
Apply
your
voice
to
the
microphone
unit
at
right
Microphone
capsule,
FET
(Q101,
102),
RV101,
angle as shown.
parts
on
amp
board
(except
for
C102,
103,
202,
203).
B)
Adjust
RV101
to
obtain
minimum
output
from
.
headphone
output.
¢ : » non-metallic
screwdriver
Wear closed type headphones.
ey,
tape
recorder
microphone input

AST
Od
(94
NOLYNOISAQ
Jal)
WY,
aZIS
AMALIVE AYO aay
yug; ~ yu) >
INSYYND
WLOL
AG‘L-S'b
Bu0l
spoue
oO-D-8
Ni
9d
Ux
epoureo
yous
10IND
Agu
ogous
epoue
|
apoyleo
|
‘6LLSSL
|
MALU
|
‘
|
|
‘
|
TT
|
|
(i
US)
apis
sane,
||
7
|
:
034
0
,
rams
q
WAS
MLLENSZ
|
=
(Ae'0)
(A220)
(Adz’
RO
Sea
MINEO
ATO
ASCO
A9z°0
[duVvo
dV)
—<
|
/
G3E
ord
12°
ZO6dIN
@0l0
JOG
DIW
apis
JOJONPUOD
ay}
Woy
Pa}9e4}x9
Sed
:——-e
@
eon
18-18S~z0Sz
s}noAe]
pea]
10}9npuosiwses
e
WVYHSVIG
ONILNNOW
‘Y

ECM-Z200
(94
NOLLVNOISAC
23l)
ASI
Od
VV,
AZIS
use
ABC
wus
~yu
|
a>
|
LNBYYND
“TWLOL
9M1d
INIW
Jamod LOLS
uolzsod
YoUMS
“ON
*39Y
YoUIMs
(ZOL
‘LOLO)
L34
$0
yuUes
By}
01
Gulps090e
abueyo
abeijOA
samog
:
*
“AG
Ajddns
semod
jeusa}xa
BulAjddy
:
(
)
*(AG'L)
Salzazeq
Alp
yyim
Buljyesadg
:
sew
Ou
“(A/O4A0G)
WOA
&
U]IM
suO!}ipuod
jeubls-ou
uspun
uayel
ase
shulpeay
“O3Y
AOVLIOA
18S729S2
dWY
TVWNOIS
10
18Sb29S2
Ol~ZLOLO
ANaWisAray
ray
IN3WIS
ALIAILOSUIO
ALIAILOSUIG
*pajou
aSIMJULO
ssajuN
puNoJG
0}
Yadsai
YIM
Op
aie
sabe1yop
e
“jedas
104
uawysnipe
:
(|
e
“‘paijioads
asIMJaYyLO
ssajuN
ssa}
40
pA*A
pue
ZV.
Ul
Ble
sIOJsISAI
[IY
.©
“‘suunjezue}
pue
$912A[04}091a
10}
}d|aoxa
pazedipul
OU
aie
ssaj
JO
AMOS
jr
:4d
“pajou
asimsayio
ssajun
47
ul
ase
suoqoeded
iy
©
:830N
AAV
TWNOIS
18S%29S2
901 ~ £010
201
09
ZO6OIN
(A
2010
YaLYSANOD
e
SONVGIdWI
f—LLENSe
j
2011010
o-1ind
|G

ECM-Z200
6. EXPLODED VIEW AND PARTS LIST
NOTE:
* The mechanical parts with no reference
number in the exploded views are not
supplied.
* Items marked " *" are not stocked since
they are seldom required for routine
service. Some delay should be antici-
pated when ordering these items.
= °
.
iad
FOU O™NAUOPWNHE
(all ed aual mall onload anltand OO™A MNS WH
Part No.
2-537-317-01
2-537-309-01
X-2537-303-1
2-537-308-01
*2-537-312-01
*2-537-314-01
2-523-713-00
2-533-813-00
*X~2537-301-1
*2-537-315-01
*X-2537-302-1
*2-537-313-01
* 2-532-809-00
-- 2«532-816-00
2-537-305-01
2-537-301-01
7-685-133-14
2-533-805-00
2-520-118-00
Description
SCREEN, WIND
RING, LOCK
CASE ASSY, MICROPHONE
RING, STOPPER
SCREEN, INNER
GRILLE, SIDE
TERMINAL
REGISTER, BACK
PLATE ASSY (A), SHIELD
COVER, PC BOARD
PLATE ASSY (B), SHIELD
REGISTER (A), BACK
HOLDER, SHOE
KNOB, FIXED
WASHER, SHOE
DAMPER (INSERT), SHOE
SCREW +P 2.6X6 TYPE2 SLIT
COVER, BATTERY
LABEL
REMARKS |No. Part No.
20 7-621-255-85
21 2-520-113-00
22 2-537-319-01
23 7-621-559-30
24 =*2-533-804-00
25 2-524-105-00
26. ¥*2-537-316-01
27 -9-911-815-03
28 7-621-772-18
29 2-537-304-01
30 2-284-602-11
31 2-537-311-01
32 2-537-318-01
33 2-537-320-01
34 = *2-537-306-01
901 8-814-173-00
902 *1-615-051-11
903 *1-615-052-11
904 1-557-873-11
* The construction parts of an assembled
part are indicated with a collation
number in the remark column.
Description REMARKS
SCREW +P 2X14
BOARD, TERMINAL, POSITIVE
CHASSIS
SCREW +K 2.6X5
PLATE, BLIND
SPRING
CUSHION, PC: BOARD
CUSHION
SCREW +B- 2X4
KNOB, SWITCH
BUSHING
LABEL
CASE
KNOB, CONTROL
TERMINAL , GROUND
MICROPHONE UNIT CU11-01
PC BOARD, AMPLIFIER
PC BOARD, CONTROL
CORD, MICROPHONE (ONE CORE)

NOTE:
Items marked " * " are not stocked since
they are seldom required for routine -
service.
pated when ordering these items.
Some delay should be antici-
- If there are two or more same circuitsin a
set such aS a stereophonic machine, only
typical circuit parts may be indicated and
capacitors and resistors in other same
circuits may be omitted.
Ref.No.
901
902
903
904
C101
C102
C103
C104 .
C201
C202
C203
C204
C301
C302
C303
C304
C305
C306
C307
C308
C309
C310
C312
C401
C402
C403
c404
C405
C406
C407
C408
CN101
Didi
D102
D103
Q101
Q1o2
Q103
Qi04
Q105
Q106
Q107
Q108
Q109
Q110
Qlil
ELECTRICAL PARTS
Part No.
8-814-173-00
*1-615-051-11
*1-615-052-11
1-557-873-11
1-161-022-00
1-102-106-00
1-102-106-00
1-124-222-00
1-161-022-00
1-102-106-00
1-102-106-00
1-124-255-00
1-124-255-00
1-102-106-00
1-124-249-00
1-124-255-00
1-102-106-00
1-102-106-00
1-162-290-31
1-162-290-31
1-102-106-00
1-130-483-00
1-124-255-00
1-130-478-00
1-130-478-00
1-102-106-00
1-124-231-00
1-101-002-00
1-124-432-00
1-124-432-00
1-124-432-00
1-562-767-11
8-719-911-19
8-719-160-52
8-719-911-19
8-729-802-30
8-729-802-30
8-729-205-84
8-729-205-84
8-729-205-84
8-729-205-84
8-729-205-84
8-729-205-84
8-729-205-84
8-729-205-84
8-729-205-84
Description
MICROPHONE UNIT CU11-01
PC BOARD, AMPLIFIER
PC BOARD, CONTROL
CORD, MICROPHONE (ONE CORE)
CERAMIC
CERAMIC
CERAMIC
ELECT
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
CERAMIC
ELECT
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
MYLAR
ELECT
MYLAR
MYLAR
CERAMIC
ELECT
CERAMIC
ELECT
ELECT
ELECT
0.056MF
100PF
100PF
22MF
0.056MF
100PF
100PF
1MF
IMF
100PF
0. 1MF
IMF
100PF
100PF
470PF
47 0PF
100PF
0.01MF
IMF
0.0039MF
0.0039MF
100PF
4. 7MF
0.0022MF
47MF
47MF
47MF
JACK, EXTERNAL POWER
DIODE 1S$119
DIODE SR605C
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DIODE 1S$119
2SK377-d
2SK377-J
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
2SC2458L-BL
CAPACITORS:
MF:uF, PF:uuF.
RESISTORS
- All resistors are in ohms.
* F : nonflammable
COILS
+ MMH : mH, UH : LH
Ref.No.
R101
R102
R103
R104
10% 25V R105
10% 50V R201
10% 50V R202
R203
20% 6.3V
10% 25V R204
10% 50V R205
R206
10% 50V R207
20% 50V
20% 50V R301
R302
10% 50V R303
20% 50V R304
20% 50V
R305
10% 50V R306
10% 50V R307
10% 50V R308
10% 50V R309
10% 50V R401
5% 50V R402
R403
20% 50V
5% 50V R404
5% 50V R405
R406
10% 50V
20% 16V RV101
50V RV102
20% 4yv $101
20% 4v
20% 4yv
ACCESSORY & PACKING MATERIAL
Part No.
1-528-027-11
Description
(Canadian,AEP ,UK,E)...BATTERY, NEW SUPER
ECM-Z200
SEMICONDUCTORS
In each case, U : u, for example:
UA...: YA..., UPA...: WPA..., UPC...: UPC,
UPD...: UPD...
ELECTRICAL PARTS
Part No. Description
1-247-849-00 CARBON 5.6K 5% 1/6W
1-247-893-00 CARBON 390K 5% 1/6W
1-247-849-00 CARBON 5.6K 5% 1/6W
1-247-829-00 CARBON 820 5% 1/6W
1-247-839-00 CARBON 2.2K 5% 1/6W
1-247-849-00 CARBON 5.6K 5% 1/6W
1-247-893-00 CARBON 390K 5% 1/6W
1-247-849-00 CARBON 5.6K 5% 1/6W
1-247-829-00 CARBON 820 5% 1/6W
1-247-829-00 CARBON 820 5% 1/6W
1-247-839-00 CARBON 2.2K 5% 1/6W
1-247-839-00 CARBON 2.2K 5% 1/6W
1-247-899-00 CARBON 680K 5% 1/6W
1-247-847-00 CARBON 4.7K 5% 1/6W
1-247-841-00 CARBON 2.7K 5% 1/6W
1-247-893-00 CARBON 390K 5% 1/6W
1-247-849-00 CARBON 5.6K 5% 1/6W
1-247-829-00 CARBON 820 5% 1/6W
1-247-877-00 CARBON 82K 5% 1/6W
1-247-899-00 CARBON 680K 5% 1/6W
1-247-847-00 CARBON 4.7K 5% 1/6W
1-247-879-00 CARBON 100K 5% 1/6W
1-247-899-00 CARBON 680K 5% 1/6W
1-247-847-00 CARBON 4.7K 5% 1/6W
1-247-899-00 CARBON 680K 5% 1/6W
1-247-827-00 CARBON 680 5% 1/6W
1-247-807-00 .CARBON 100 5% 1/6W
1-230-068-00 RES, ADJ, CARBON 47K
1-230-737-11 RES, VAR, SLIDE 50K
1-554-438-00 SWITCH, SLIDE
(SUM-3) (NS)
1-556-251-00
1-557-872-11
2-534-019-01
2-534-020-01
2-537-317-01
2-537-321-01
2-537-323-11
2-537-324-01
2-537-325-01
2-599-250-11
2-599-250-21
CORD, CONNECTION (RK-510)
CORD, CONNECTION (RK-520)
LID, TRANSPARENT
FRAME, PROTECTION, INDIVIDUAL
SCREEN, WINDOW
CASE, CARRYING
INDIVIDUAL CARTON
LABEL
FRAME, INNER
(Canadian,AEP,UK,E)... MANUAL, INSTRUCTION
(US)..... MANUAL , INSTRUCTION

ECM-Z200
English
. 85A04135-1
Sony
Corporation
Printed
in
Japan
9-951-628-11 aes <a © 1985