KanDao Obsidian GO User manual

GO Remote
Product description
使用说明书

目录
一、遥控器部件识别
二、通 过遥控器控制相机
2.1 安装电池和连接相机
2.2 拍照
2.3 录影
2.4 关机
2.5 遥控器指示灯状态说明
中文产品说明
使用设备前，请仔细阅读本说明书

一、遥控器部件识别
蜂鸣器
电池盖
电源键
拍照键
录影键
拍照指示灯
电源指示灯
录影指示灯

二、通过遥控器控制相机
短按遥控器[拍照键] ，[蜂鸣器]和[电源指示灯]同
时响应1次，相机进入Timelapse 10秒拍照模式后，遥
控器[拍照指示灯]慢闪提示，再次短按[拍照键]，相机
实现停止拍照功能。
遥控器电池盖抠手的位置取下电池盖
可装取2节7号干电池。
2.2 拍照
2.1 安装电池和连接相机
连接相机：
先开启相机, 再任意按摇控
器上的按键, 遥控器启动并
进入连接状态,[电源指示灯]
慢闪直到连接完成后, [电源
指示灯]会灭掉 。
电池
短按遥控器[录像键] ，[蜂鸣器]和[电源指示灯]
同时响应1次，相机进入录像模式后，遥控器录像指
示灯呈慢闪提示，再次短按遥控器录像键，相机实现
停止录像功能。
2.3 录像

温馨提示：
1. 遥控器只要有按键操作，[电源指示灯]和[蜂鸣器]都会
同时响应；
2．相机如在使用过程中出现故障，遥控器上的[指示灯]会
呈快闪的方式提醒。
长按遥控器[电源键] ，相机实现关机功能后遥控
器自动进入休眠状态，所有指示灯灭。
2.4 关机
2.5 遥控器指示灯状态说明
慢闪 快闪
相机与遥控器正常连
接，相机为待机状态
相机开机状态下，但未
能与遥控器配对未连上
相机拍照中
相机录影中
相机拍照中发生异常，此时
会与电源灯一起闪烁
相机录像中发生异常，此
时会与电源灯一起闪烁
相机低电，相机
不正常工作时
遥控器开启状态下，短按遥控器电源键，遥控器进入休眠
模式.再次短按遥控器任意键可实现遥控器唤醒。

Table of Contents
Product Description
1, Remote control
2.1 Install the battery & connect with camera
2.2 Photograph
2.3 Video-record
2.4 Power off
2.5 Indicator lamp description
2, Operate with remote control
Please read the product descripiton
carefully before using the device.

Photograph
indicator lamp
Power
indicator lamp
Camcorder
indicator lamp
Power button
Photograph button
Camcorder button
Buzzer
Battery cover
1, Remote control

2, Operate with remote control
Shortlypress the [photograph button] on remote
control, you will hear a buzz as [power indicator lamp]
flashesonce. After that,the camera comes into 10-second
time-lapse mode,[photograph indicator lamp] on remote
control will flash slowly,shortly press [photograph button]
again to stop taking photograph .
Shortlypressthe[camcorder button]  on the
remote control, the buzzer will respond and [power
indicator lamp] will flash onceasrecording starts. During
the recording process, [camcorder indication lamp]on
the remote control will flash slowly. Shortlypress[camera
button] again to end recording.
Open the battery cover of the
remote control, then two AAA
batteries can be installed into
the remote control.

2.2 Photograph
2.3 Video-record
2.1 Assemble the battery and
connect with camera
Switch on camera first,
then press any button on
the remote control to start
connecting, during this
process [power indicator
lamp] will flash slowly, and
then go off after the
connection is done.
batteries

2.5 Indicator lamp description
Reminder:
1. In a normal working status, once a button is pressed on
remote control, [power indicator lamp] and [buzzer] will
both respond.
2. If the camera is in abnormal status, all indicator lamps
on the remote control will flash quickly.
Camera is in dormancy
Camera is on but
disconnected with
remote control
Taking a photograph
Recording a video
An error has occurred
during taking a
photograph
An error has occurred
during recording a video
Low power/
camera is in
abnormal status
Slow flash Quick flash
2.4 Power off

FCC Special Statement
FCC Regulatory Information
Warning: changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio communica-
tions. However, there is no guarantee that
interference will not occur in a particular
installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the
equipment and receiver.
-- Connect the equipment into an outlet on a
circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV
technician for help.

深圳看到科技有限公司
KanDao Technology’s founders and core team members come from
top universities all around the world such as the University of Hong Kong,
Tsinghua University, Hong Kong University of Science and Technology,
National University of Singapore and University of California, San Diego,
with backgrounds in leading technology institutions such as Huawei,
Tencent, Netease, CLP and other well-known enterprises. With strong
research, development, and operational capabilities, Kandao sets a
high international standard in the industry of panoramic virtual reality
video making.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
FCC ID: 2AMZV-KDOZ

GET MORE HELP ( IF YOU NEED IT)
CALL [phone]
ADD: Unit 5D, Block M7, SinoSteel Building,
Nanshan, Shenzhen, China
深圳市南山区科文路9号中钢大厦
Email: [e-mail]
WEB: www.kandaovr.com
联系我们