Kangaroo Wallaby II User manual

SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Wallaby II
ITEM NO.: K8405 Teak
K8411 White Ash

2
Wallaby II Assembly Instructions
Read the instructions carefully before starting. Please open and inspect the contents of boxes to
see that all parts are included. You will need a Phillips head and a flat head screwdriver. A power
screwdriver or cordless drill is preferable. Ensure that the Phillips head fits neatly and fully engages
the screw to avoid damage to the screws. Make sure that you tighten all screws securely and tap
wooden dowels all the way in.
Use and Care
Your cabinet normally requires a minimum amount of maintenance; however, the following points are
worth noting:
Cleaning – To remove marks and enhance the surface, wipe with general purpose cleaner.
Caution – Do not use ammonia-based cleaning agents. Do not use harsh chemicals or abrasive
cleansers. The surface can be wiped with a damp cloth but should be dried quickly.
Electrical and Hydraulic Lifts – Require annual lubrication.
180°
Screw cam bolts flush as
illustrated.
Press cam Into hole until flush with
surface. The arrow direction must
be in the direction of the hole!
Insert bolt through pre-drilled
hole in edge of panel.
Understanding How the Cam Fastener Works
Turn clockwise to lock cam with bolt.

3
Wallaby II Assembly Instructions
Parts List
ITEM DESCRIPTION QT Y. PACK.
ATop Panel 1 1 of 4
BRight Leaf 1 1 of 4
CLeft Leaf 1 1 of 4
A5 Platform Cover 1 1 of 4
GBottom Panel 1 1 of 4
DBack Panel 1 2 of 4
ZRight Side Panel 1 2 of 4
A1 Quilt Extension Panel 1 2 of 4
V1 Left Door Panel 1 2 of 4
V2a Right Main Door Panel 1 3 of 4
XLeft Side Panel 1 3 of 4
YPartition 1 3 of 4
FFixed Shelf 1 3 of 4
ITEM DESCRIPTION QT Y. PACK.
V2b Right Door Edge Panel 1 3 of 4
LDrawer Front 1 3 of 4
L1 Drawer Side Left 1 3 of 4
L2 Drawer Side Right 1 3 of 4
L3 Drawer Back 1 3 of 4
L4 Drawer Bottom 1 3 of 4
OInsert Holder 1 3 of 4
01 Gate Leg 1 3 of 4
K1 Door Bin Front Panel 1 3 of 4
K2 Door Bin Bottom Panel 1 3 of 4
K3 Door Bin Sides 2 3 of 4
K4 Fixed Shelf On Door 3 3 of 4
A4 Platform 1 3 of 4
Lift & Rails 1 4 of 4
K3
K3
K1
K2
K4
K4
K4
V2a
V2b
Z
A
C
B
A5
A1
O1
D
A4
O
G
X
V1
F
Y
L3
L1
L4
L
L2

4
Wallaby II Assembly Instructions
Parts List
6x35 Cam Bolt x35
3.5x14 Screw x52 3x14 Screw x28 3x20 Screw x4
Wrench x1 Handle x2 Door Plate x2 14mm Spanner x1
Stay Arm x1
Cam
6x25 Cam Bolt x25
5⁄8“ Cam Cover x60 6x50 Dowel Pin x33
Alignment Pin x1
Flap Hinge x3
Caster x3 Locking Plate Caster x5
Butt Hinge x2 Flush Hinge x6
Lock x1 Magnet x1
Lock plate x1 Catch plate x1Key x2
8x16 Fix Bolt x20 4x20 Fix Bolt x4
Pre-installed parts
ITEM DESCRIPTION QT Y.
c1 6x35 Cam Bolt 35
c3 6x25 Cam Bolt 25
d1 8x30 Dowel Pin 36
d2 6x50 Dowel Pin 33
c2 5⁄8“ Cam Cover 60
t2 Locking Plate Caster 5
aWrench 1
s2 3x14 Screw 28
SStay Arm 1
r3 14mm Spanner 1
d3 Door Plate 2
s5 Alignment Pin 1
ITEM DESCRIPTION QT Y.
s3 3.5x35 Screw 4
hHandle 2
h3 Flap Hinge 3
h2 Flush Hinge 6
b2 4x20 Fix Bolt 4
b1 8x16 Fix Bolt 20
s1 3.5x14 Screw 52
mMagnet, Catch Plate 1
LLock, Lock Plate, Keyx2 1
t1 Caster 3
h1 Butt hinge 2
s4 3x20 Screw 4
d2
s5
b2
s2
s4
h
d3
r3
h1
h2
L
m
t1
t2
Drawer RunnersCaster Bracket
8x30 Dowel Pin x12
d1
3.5x35 Screw x4
c1
c3
h3
b1
s1
a
s
c2
c5
s3

Wallaby II 5Assembly Instructions
3.5x14 Screw x23
Stay Arm x1
8x30 Dowel Pin x12
Magnet x1
Lock Plate x1
Catch Plate x1
d1
r3
L
m
t1
Step 1. Preparation Panels A, A1, Z, X, F and O1
1. Insert cams bolts c1 into panels A, Xand Zas illustrated below.
2. Insert dowel pins d1 to panels X, Zand Fas illustrated below..
3. Fix Stay Arm susing Screws s1 to panel Aas illustrated below.
4. Fix Lock Plate using Screws s1 to panel Aas illustrated below. Orient the flat face of lock plate Ltowards front edge of
panel A.
5. Fix Magnet musing Screw s1 to panels A1 as illustrated below.
6. Fix Flap Hinge h3 using Screw s1 to panels A1 as illustrated below.
7. Fix Butt hinges h1 using Screws s1 as shown on Panel O1. Insert the Alignment pin s5.
8. Insert the caster t1 into the pre-installed caster bracket on panel O1 and tighten with spanner r3.
9. Fix Catch plate mto panel O1 using screws s1.
h3
Flap Hinge x3
14mm Spanner x1
Caster x1
6x35 Cam Bolt x15
Butt Hinge x2
Alignment Pin x1
c1
c1
c1
h3
s1
s1
s1
s1
s1
s
s
Z
A
O1
A1
X
F
L
m
t1
r3
s5
s1
s1
h1
c1
m
h1
s5

6x25 Cam Bolt x25
c3
4x20 Fix Bolt x4
b2
Wallaby II 6Assembly Instructions
3.5x14 Screw x4
Step 2. Preparation Panels Y, D, 0, V1, V2a, V2b, K1, K3, K4, L, L3 and L2
1. Insert cam bolts c1 into panels Yand V2a and Las illustrated below.
2. Insert cam bolts c3 into panels V2a, K1 and K3 as illustrated below.
3. Insert dowel pins d1 into edges of panels Y, D, V2b, L1 and L2 using glue as illustrated below.
4. Insert dowel pins d2 into top of panels K4 using glue to secure.
5. Fix Lock mechanism Linto corner of V2a using s4 screws. Add trim ring to exterior end of lock.
6. Fix Door plate d3 to panel V1 using screws s1.
7. Attach Flush Hinges h2 to panel V1 using s2 screws as shown.
8. Attach the screw-in caster to V1 and V2a panel caster bracket and tighten with spanner t1.
9. Attach door handles hto exterior of V1 and V2a using fix bolts b2 as shown.
14mm Spanner x1
Caster x2
x3
6x35 Cam Bolt x6
6x50 Dowel Pin x33
3x20 Screw x4
Lock x1
Key x2
Door Plate x2
Flush Hinge x3
3x14 Screw x6
Handle x2
8x30 Dowel Pin x12
c1
c1
c1
c1
c1
b2
h
h2
s1
s2
D
Y
L
L
s4
t1
r3
d3
c3
c3
c3
K3
K1
K4
V2a
V2b
O
V1
L
d3
h2
d1
r3
t1
c1
s1
d2
s4
L
s2
h
x2
L2
L1

Wallaby II 7Assembly Instructions
3.5x14 Screw x3
Step 3. Fix Lifter Rail (right) to Zpanel with s1 screws following predrilled holes as shown on the illustration below.
Step 4. Fix Lifter Rail (Left) to Ypanel with s1 screws following predrilled holes as shown on the illustration below.
Lifter Rail (Right) x1
Lifter Rail (Left) x1
3.5x14 Screw x3
Rail faces front of panel.
Detail beside shows the holes
on back as it attaches to panel.
s1
s1
s1
s1
Y
Z

Wallaby II 8Assembly Instructions
Step 5. Panels D, X, Z assembly.
Insert cam bolts c1 on panels Xand Zinto cams on panel Dand tighten in a clockwise direction as illustrated below. Apply
cam covers c2 over tightened cams.
Panel D has the cams facing
outside to the back of the
cabinet and will be covered
with stickers provided.
Step 6. Panel F and Y assembly.
Insert cam bolts c1 on panels Xand Yinto cams on panel Fand tighten in a clockwise direction as illustrated below. Apply
cam covers c2 over tightened cams.
Important Note:
We recommend doing this step
with panels upside down so
panels are in correct position for
Step 6 on page 8 and Step 8 on
page 9.
180°
180°
5⁄8“ Cam Cover x4
5⁄8“ Cam Cover x4
Z
Z
Y
F
D
D
X
X
c2
c2
c5
c5

180°
Wallaby II 9Assembly Instructions
Step 7. Panel G assembly.
1. Fix casters t2 to panel Gwith bolts b1 as illustrated below.
2. Flip panel Gover to top side. Install cam bolts c1 as illustrated below.
3. Attach insert holder Oby inserting cam bolts c1 on panel Ginto Oand tightening cams clockwise.
Step 8. Panel G assembly.
1. Remove the drawer runners from panels Xand Y.
2. Insert cam bolts c1 on panel G into cams on panels X, D, Yand Zand tighten in a clockwise direction as illustrated
below. Apply cam covers c2 over tightened cams.
3. Attach the drawer runners on panels Xand Y.
Locking Plate
Caster x5
8x16 Fix Bolt x20
6x35 Cam Bolt x11
Wrench x1
180°
5⁄8“ Cam Cover x9
1. 2.
3.
G
X
X
Y
X
Y
Y
Z
D
G
t2
t2
b1
b1
c1
a
O
G
c5
c2
c5

Wallaby II 10 Assembly Instructions
Step 10. Lifter Panel assembly.
Fix Lifter to A4 panel with s1 screws following predrilled holes as shown on the illustration below.
Note: Remove cable ties (do not remove wooden block).
Step 9. Flip cabinet over (right side up).
3.5x14 Screw x4
s1
Lifter x1
A4
s1

Wallaby II 11 Assembly Instructions
Step 12. Panel A assembly.
1. Insert cam bolts c1 on panel A into cams on panels X, D, Yand Zand tighten in a clockwise direction as illustrated.
Apply cam covers c2 over tightened cams.
Step 11. Mounting the Lifter Assembly.
1. Position lifter onto side rails using plastic guides; make sure the cable is hooked into the rail tabs on both sides then
lower the lift. See illustration below.
2. When lifter is pushed to first lock position remove a small wooden block that will be released from lifter.
180°
5⁄8“ Cam Cover x9
Plastic guides Cable
Lifter rail
Lifter rail
Rail tabs
A4
c2
Y
A
X
Z
D
c5

Wallaby II 12 Assembly Instructions
Step 14. Drawer assembly.
Step 13. Drawer assembly.
1. Insert cam bolts c1 on panel Linto cams on panels L1 and L2 and tighten in a clockwise direction as illustrated below.
Apply cam cover c2 over tightened cams.
2. Slide bottom L4 into L, L1, L2 and L3 grooves as illustrated.
3. Connect drawer panels L1, L2 and L3 with screws s3 as illustrated below.
Apply cam cover c2 over tightened cams.
180°
5⁄8“ Cam Cover x4
3.5x35 Screw x4
s3
L
L3
L4
L2
L
L1
c2
c5
s3

Wallaby II 13 Assembly Instructions
Step 16. Panel V2 assembly.
1. Insert cam bolts c1 on panel V2a into cams on panels V2b and tighten in a clockwise direction as illustrated below.
2. Insert cam bolts c3 on panel V2a into cams on panels K1 and K4 and tighten in a clockwise direction as illustrated below.
3. Fix flush hinges h2 to panel V2b with screws s2 as illustrated below.
Apply cam covers c2 over tightened cams.
Step 15. Door Bin assembly.
1. Insert cam bolts on K3 sides into cams in K2 bottom panel and tighten cams in clockwise direction.
2. Insert cam bolts on K1 front into cams in K2 bottom panel and sides K3 and tighten cams in clockwise direction.
5⁄8“ Cam Cover x13
180° 180°
c5
Flush Hinge x3
3x14 Screw x6
K1
K3
K2
K3
K4
K4
K4
c5
c2
V2a
V2b
K1
h2
h2
s2
s2

Wallaby II 14 Assembly Instructions
Step 18. Panel V1 assembly.
1. Fix flush hinges h2 on panel V1 to Xwith screws s2 as illustrated below.
2. Fix Stay Arm swith Screws s1 to panel V1 as illustrated below.
3x14 Screw x6
s2
s
Step 17. Panel V2 assembly.
Fix Flush hinges h2 on panel V2b to Z with screws s2 as illustrated below. It is helpful to have two people hold the door,
but it is not required.
3x14 Screw x6
V1
X
s2
h2
3.5x14 Screw x2
s1
s1
V2b
Z
s2
s2
h2

Wallaby II 15 Assembly Instructions
Step 20. Panel A1 assembly.
1. Have a second person hold the A1 Quilt panel balanced on the gate leg panel O1.
2. Using screws s1 attach the flap hinges h3 to panels Dand A1 from underneath panel A1.
Step 19. Panel 01 assembly.
1. Fix O1 panel butt hinges h1 on to panel Dwith screws s1 as illustrated below.
s1
D
D
O1
O1
A1
3.5x14 Screw x9
3.5x14 Screw x6
s1
s1
s1
h1
h3

SEW IN COMFORT. SEW LONGER.™
LIMITED LIFETIME WARRANTY
Kangaroo™ Sewing Furniture Limited Lifetime Warranty
WHAT THIS WARRANTY COVERS: Arrow Companies, LLC (Arrow) provides limited warranty coverage
to the original purchaser of this product against defects in materials or workmanship of Arrow furniture
components for a period of ten years from the date of purchase. As used in this Warranty, “defect” means
imperfections in components which substantially impair the utility of the product. This Warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
HOW TO GET SERVICE: Simply contact Arrow at 1-800-533-7347 or [e-mail]. When you
request warranty service, you must also present proof of purchase documentation, which includes the
date of purchase (detailed receipt), and photos of the product. Arrow will replace any defective part (at
its sole option), excluding labor. Replacement parts will be warranted for only the remaining period of
the original Warranty.
Replacement parts will be shipped freight prepaid on any initial warranty claim during first year of Warranty
only. Warranty applies only to defects confirmed by Arrow Companies, LLC and will be replaced or repaired
at Arrow’s option. In the event parts are no longer available for a warranty claim, customer may receive
brand new cabinet at a price equal to 60% off the MSRP of a current comparable model.
WHAT’S NOT COVERED: There is no warranty coverage for defects or conditions that result from the failure
to follow product assembly instructions, information or warnings, misuse or abuse, intentional damage,
fire, flood, alteration or modification of the product, or use of the product in a manner inconsistent with
its intended use, nor any condition resulting from incorrect or inadequate maintenance, cleaning, or care,
or neglect, cuts or scratches. Caster damage as a result of moving furniture fully loaded or with locked
casters. Damage resulting from electrical surge or lightning. Use in commercial or education environments.
Kangaroo Sewing Furniture is designed for residential use only.
ARROW SHALL HAVE NO LIABILITY for ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND and
all such damages are EXCLUDED FROM THIS WARRANTY, such as loss of use, disassembly, transportation,
labor or damage to property on or near the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The
Warranty cannot be transferred to subsequent owners or users of the product, and it shall be immediately
void in the event the product is resold, transferred, leased or rented to any third party or person other than
the original purchaser.
ADDITIONAL LIMITATIONS:
THERE ARE NO OTHER WARRANTIES APPLICABLE TO THIS PRODUCT. Under the laws of certain states,
there may be no implied warranties from Arrow and all implied warranties, INCLUDING ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE are disclaimed where
allowed by law. TO THE EXTENT ANY IMPLIED WARRANTIES ARE APPLICABLE, ANY IMPLIED WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY or the minimum period
allowed by law, whichever is shorter. Some states do not allow limitations on how long an implied Warranty
lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights.
This limited warranty does not, in any way, affect the rights given to you by law.
REGISTER YOUR PRODUCT: Original purchaser should register the purchase online at www.ArrowCabinets.com/warranty.

SEW IN COMFORT. SEW LONGER.™
Enhance your sewing experience with a custom-
made insert for your Arrow or Kangaroo cabinet.
Inserts are designed to reduce the gap between
the machine and cabinet opening. This provides
an ergonomic work surface for the free arm of the
sewing machine, allowing for straighter stitches,
less fatigue and an overall better experience
using your machine and cabinet.
Hydraulic Sewing Chair
Insert
Our adjustable height sewing chair is a perfect
accessory for any craft and sewing room. The
chair’s height is adjustable with easy to use
controls and the cushions provide perfect lumbar
support and comfort for those long sewing hours.
Chair features five casters on a star base for
greater movement at your sewing cabinet or
crafting surface. Lift the seat cushion to reveal
a hidden storage compartment for your small
notions or patterns.
Accessories to Complete Your Sewing Experience
P.O. Box 307 Delavan, WI 53115
1-800-533-7347 Ext. 1
[e-mail]
www.ArrowCabinets.com 07-20
Custom Insert Arrow Sewing Chairs