Karisma DEVIL Parts list manual

DEVIL
WASH UNIT
K7410_K7412_K7413
INSTRUCTIONS FOR INSTALLATION, USE AND
ROUTINE MAINTENANCE

2
CONTENTS
Instructions for Installation, Use and Maintenance
INTRODUCTION .............................................................................................................................................................3
PREREQUISITES ................................................................................................................................................................4
INTENDED USE ................................................................................................................................................................4
INSTRUCTIONS FOR USE ...........................................................................................................................................4
DEFINITION .......................................................................................................................................................................4
SAFETY ...............................................................................................................................................................................4
ELECTRICAL SPECIFICATIONS ....................................................................................................................................5
MIXER SPECIFICATIONS ...............................................................................................................................................5
THERMOSTATIC MIXER SPECIFICATIONS ...........................................................................................................5
TRANSPORT AND STORAGE ..................................................................................................................................... 6
DIMENSIONS ....................................................................................................................................................................6
INSTALLATION SURFACE ..............................................................................................................................................7
PREPARATION ..................................................................................................................................................................9
WASH UNIT ATTACHMENT ........................................................................................................................................9
FLOOR DRAIN ...............................................................................................................................................................10
WALL DRAIN ..................................................................................................................................................................11
ELECTRICAL CONNECTION ........................................................................................................................................12
TESTING ...........................................................................................................................................................................13
USE .....................................................................................................................................................................................13
SWITCHING ON THE EQUIPMENT .........................................................................................................................13
RELAX CONTROLS ........................................................................................................................................................14
JET MASSAGE CONTROLS .........................................................................................................................................15
ROUTINE MAINTENANCE ..........................................................................................................................................16
CHAIR ...............................................................................................................................................................................16
WASHBASIN UNIT .........................................................................................................................................................16
CLEANING THE SURFACES .........................................................................................................................................17
ELECTRICAL FUNCTIONS ........................................................................................................................................18
IDENTIFICATION OF THE EQUIPMENT ................................................................................................................18
INSTRUCTIONS FOR DISPOSAL .............................................................................................................................18

3
Thank you for purchasing a Karisma product. We are certain you will be fully satised with your
choice.
Karisma products are manufactured according to strict quality standards using only the best compo-
nents.
The operation and safety of each wash unit were tested in painstaking detail before shipment.
Check that the wash unit was not damaged during transport in a manner that could impair its operation
and safety.
You are advised to follow the instructions contained in this manual carefully for the best reliability, long
life and top-notch performance of the wash unit.
The manual is designed to allow you to use the wash unit in the best and safest manner.
Therefore, this manual is an integral part of the wash unit. It must be kept carefully throughout the dura-
tion of the wash unit and accompany the wash unit if it is transferred to a new user.
To avoid problems, read this manual carefully before carrying out any operation on the wash unit and
follow the instructions scrupulously.
The manufacturer accepts no liability for damage caused by negligence and/or failure to observe the
instructions in this manual.
Without prejudice to the main technical and safety features of the product, the manufacturer reserves
the right to make changes to the wash unit for reasons of continual technical and technological evolu-
tion without prior notice, without incurring any penalty.
The partial or total reproduction of this manual, including texts and illustrations, is prohibited by law.
The Court of Reggio Emilia (Italy) is competent in case of disputes.
INTRODUCTION
Instructions for Installation, Use and Maintenance

4
PREREQUISITES
The wash unit chair is intended for professional use in hair treatment salons, particularly in the hair
washing area.
INTENDED USE
INSTRUCTIONS FOR USE
DEFINITIONS
The equipment complies with the essential European Union regulations on ergonomics
and safety. The manufacturer guarantees these qualities by axing the CE marking.
SAFETY
The following requirements must be observed for a correct and safe installation of the equipment:
1) The oor must comply with DIN 1055 B 1.3 and DIN 18560 T 1.
2) The electrical system must comply with CEI 64.4 standards, using 250V/16A dierential protection
conductors (<30mA).
3) Do not connect devices that are not specied as part of the system.
4) Earthing, in particular, must comply with Article 3.2.01 of the aforementioned standards.
5) The equipment must be xed to the oor using anchor bolts with a minimum diameter of 8 mm.
The manufacturer is not liable for the safety and reliability of the equipment if:
• installation and repairs are not carried out by authorised technicians
• the general and electrical installation of the room does not comply with the requirements
indicated above
• the device was not installed following this manual
• the device is not used following this manual.
Instructions for Installation, Use and Maintenance
The wash unit chair is intended for professional use in hair treatment salons, particularly in the hair
washing area. It cannot be used by more than one operator at the same time and can accommodate only
one customer at a time. The maximum load capacity is 120 kg. The equipment must be xed to the oor.
The installation is compliant if carried out according to the specications indicated in the Installation,
Use and Maintenance Manual. The equipment must be xed with anchor bolts with a minimum diameter
of 8 mm. Sitting on the worktops and armrests is not permitted. Multiple people are not allowed to sit
together. It is not allowed to get seated and/or get up while the footrest is moving or if the chair being
raised.
Beware of scalding caused by hot water.
Beware of moving parts of the wash unit chair.
Hairdresser, or operator, is the person who performs the treatment of the customer's hair and who man-
ages the operation of the wash unit chair. The workstation is situated at the back of the wash unit chair.
Customer is the person who is receiving the hair treatment. The front part of the wash unit chair is used
to seat the customer.

5
ELECTRICAL SPECIFICATIONS
Wash unit model
DEVIL Jet Massage
Electric DEVIL Relax
Rated
voltage
220V ~ ±10%
220V ~ ±10%
Rated
frequency
50/60 Hz
50/60 Hz
Rated power
220VA
250VA
Intermittent
operating mode
3 min. ON
5 min. OFF
8 min. ON
5 min. OFF
MIXER SPECIFICATIONS
Code K7412
Code K7413
Technical specications
Test pressure 15 bar
Cold water supply blue indicator pointing rightwards. Pipe connection 3/8″
Hot water supply red indicator pointing leftwards. Pipe connection 3/8″
Limits of use according to UNI 10234 EN (817):
MIN. pressure 0.5 bar MAX. 10 bar (100000000 pascals)
MAX. temperature 90°
Limits of use recommended by UNI 10234 (EN 817) for a good tap operation
Pressure: MIN. 0.5 bar MAX. 5 bar (50000000 pascals)
Temperature: MAX. 65°C
Warnings:
- The system pipes must be carefully rinsed to avoid damage to the taps caused by any residues in the
pipes.
- It is recommended to install a pressure reducer in case of operating pressures above 5 bar.
- It is also recommended to install a central lter for water with a high impurity content.
Technical specications
Test pressure 15 bar
Cold water supply blue indicator pointing rightwards. 1/2" pipe connection
Hot water supply red indicator pointing leftwards. 1/2" pipe connection
Limits of use according to UNI 10234 EN (817):
MIN. pressure 1 bar MAX. 10 bar (100000000 pascals)
MAX. temperature 90°
Limits of use recommended by UNI 10234 (EN 817) for a good tap operation
Pressure: MIN. 1 bar MAX. 5 bar (50000000 pascals)
Temperature: MAX. 65°C
Warnings:
- The system pipes must be carefully rinsed to avoid damage to the taps caused by any residues in the
pipes.
- It is recommended to install a pressure reducer in case of operating pressures above 5 bar.
- It is also recommended to install a central lter for water with a high impurity content.
THERMOSTATIC MIXER SPECIFICATIONS
Instructions for Installation, Use and Maintenance

6
560
590
520
660
980
470
( seat height ) 875
( neck height )
1200
1510 ( length with footrest)
DIMENSIONS
The packages must be transported on closed vehicles. Do not drop or tilt packages during loading and
unloading. The products must be stored in a dry, indoor place, stacking up to three packages on top of
each other and without drastic temperature changes.
Environmental conditions for transport and storage
• Ambient temperature from -25°C to +50°C.
• Relative humidity max 75%.
Environmental conditions of use
• Ambient temperature from +10°C to +40°C.
• Relative humidity from 30% to 75%.
TRANSPORT AND STORAGE
Instructions for Installation, Use and Maintenance
Dimensions in mm.

7
10
10
10
10
1 2
3
4
1 2
3
4
550 Min. 900
Min. 600
Distance from the wall:
Min. 1235 mm
(including 600 mm of
work space)
430
N°2 fixing slots
10x40 mm
Distance from the wall:
Min. 390 mm
Distance from wash
unit: Min. 660 mm
455
Cod: K991 - Optional casing
for vertical installation
1 2
3
4
850
100
180
WARNING: Open the side panel before xing the wash unit in a side-by-side arrangement with a side
drain.
INSTALLATION SURFACE
Instructions for Installation, Use and Maintenance
Plant layout
1 = Hot 3/8" (1/2" thermostatic mixer)
2 = Cold 3/8" (1/2" thermostatic mixer)
3 = ø 40 mm drain
4 = Electrical cable outlet (where required)
Cord 3X1 (1500 mm) - 220/240 V - 50 Hz/60 Hz
Important note The grey areas delimit the space available for installation.

8
110 400
180
600 520
Distance from the wall
or back of furniture:
Min. 1120 mm
( including 600 mm of
work space )
Cod: K991 - Optional casing for vertical installation
100
850
INSTALLATION SURFACE
1 = Determine the height of the wall drain from the ground.
2 = Open the rear wash unit casing.
3 = Locate the pre-existing slot on the inside of the shoulder and drill a centring hole at the
detected height.
4 = Fix the supplied ange with the appropriate screws on the outside of the shoulder.
5 = Open the side panel.
INSTRUCTIONS
Dimensions in mm.
Instructions for Installation, Use and Maintenance

9
2 ( X2 )
1 ( X4 )
Preparation
1) Remove the packaging leaving the wash unit mounted on the pallet so that it is easier to transport.
Remove the wash unit protections and any accessories contained in the packaging itself.
2) Position the wash unit and mark the xing points (Fig. 2). Drill holes for the anchor bolts.
Fixing the wash unit
WARNING: Prepare the holes for the drain and electrical power supply, if applicable before xing
the wash units, either in side-by-side arrangement or with side drain.
INSTALLATION
1) Undo the screws (1) fastening
the rear casing.
2) Undo the two screws xing the
wash unit to the pallet (2) and
position the wash unit in the spot
prepared for installation.
Instructions for Installation, Use and Maintenance

10
10
10
10
10
1 2
3
4
Preparation for water
connection
1 ( X2 )
Floor drain
WARNING:
The water connection may only be carried out by qualied technicians
Open the side panel (Point 2) if the installation requires infeed of the power supply from the wall or in a
side-by-side arrangement.
1) Install the water unit using ø 3/8" hydraulic connections (1/2" if thermostatic). It is advisable to provide
a gate valve upstream of each tting.
Connections to the sewage system are established using a ø 40 drain pipe.
INSTALLATION
Plant layout
1 = Hot 3/8”
2 = Cold 3/8”
3 = ø 40 mm drain
4 = Electrical cable outlet (where required)
Cord 3X1 (1500 mm) - 220/240 V - 50 Hz/60 Hz
3) Place the two nylon discs supplied
(1) under the base of the wash unit
and x it to the oor with the anchor
bolts suitable for the type of material
of which the oor is made using the
four holes provided for the purpose.
Instructions for Installation, Use and Maintenance