KEETEC TS MOTO User manual

User Manual
MOTOR CYCLE ALARM SYSTEM
KEETEC TS MOTO

Version1.2 TS MOTO
1
STANDARD CONFIGURATION FOR TRANSMITTER
Buttons
0B
Function
Condition
Press button 1 once
Arm
Stop alarm sounding
Ignition OFF
Alarm sounding
Press button 2 once
Disarm
Exit car finder mode Armed and Alarm sounding
Press button 1 and 2
together Panic Anytime
Press and hold button3
for 2 sec Enter Anti motorcycle-jacking While driving
Press button 1 once then
press button 3 within 5
sec Arm & Bypass Tilt sensor Ignition OFF
Press and hold button 1 &
4 for 2 sec Enter function selection
Ignition ON within 5
seconds
press button 2 & 3
together 1BEnter/exit VALET mode
Ignition ON within 5
seconds
Press button 4
2B
Enter car finder mode
Arming
4-BUTTON TRANSMITTER

Version1.2 TS MOTO
2
FEATURES:
CODE LEARNING
In case the transmitter is lost, or you want to add more transmitters (up to 3 most). Please
refer to following procedures:
a. In disarming mode, turn ignition ON/OFF 5 times within 15 sec, and stay in ON
position, 3 seconds later Siren will chirp 3 times to indicate system entered code
learning mode.
b. Press any button on the transmitter; siren will chirp the times of transmitter’s
sequence. E.g. once for the first transmitter, twice for the second, three times for the
third.
c. After 8 sec or turn ignition OFF, the Siren will long chirp once, system will
automatically exit code learning and store the code.
d. When the first code has been learned, all old codes will be cleared
ARMING
a. In disarmed mode, turn ignition OFF, press button I once, siren will chirp once,
parking light will flash once. After 8sec., system will armed automatically, LED
flash quickly and disable engine.
b. In arming mode, to turn on the key will trigger the siren, parking light will flash 30
seconds. The siren will keep 30 sec-cycle sounding till key turned to OFF. After the
key is turned to OFF, siren will keep sounding till cycle end.
c. Tilt SENSOR defence area
In arming mode, if motorcycle is moving or incline, siren will chirp 30 sec., parking
light will flash 30 seconds.
d. Trigger defence area
In arming mode，if the defence area was triggered, siren will chirp 30 sec., parking
light will flash 30 seconds.
Note: up to 8 times to alarm per arming cycle.

Version1.2 TS MOTO
3
ARMING AND BYPASS TILT SENSOR
When system entered arming mode, press button 1and then press button 3 once within 5
sec, system will long chirp once to indicate that the Tilt sensor is bypassed.
In the mode, LED will flash twice interval 2 seconds.
DISARMING
1. In arming mode, press button 2 once, siren will chirp twice, parking lights will
flash 2 times then system will be disarmed and enable the engine starter.
2. If the alarm is triggered during arming mode, siren will chirp 4 times when
disarming. Parking light will flash 4 times which indicates the alarm has been
activated.
AUTO RE-ARMING
After disarming, 60 sec later if driver hasn’t start engine, system will be rearmed
automatically. LED will flash quickly.
(During rearm count down, LED will flash quickly, sire will chirp once, and parking light
will flash once.)
PANIC
a. If you are threatened near your motorcycle, you can attract attention by triggering the
system with your transmitter. Just press button 1+2 together to enter panic mode. The
siren will sound for 10 sec, Press button1or2 to stop sounding, and parking lights will
flash for 10 seconds.
CAR FINDER
a. The system is armed.
b. Press button 4: siren will chirp once, parking lights will flash 10 times.
c. Press button 2 to stop car finder and disarm.

Version1.2 TS MOTO
4
ANTI MOTORCYCLE-JACKING
1. When key has been turned ON, press and hold button 3 for 2 seconds, LED will
flash quickly，then motorcycle-jacking mode is activated. Siren will chirp once
every 3sec, after chirping 5 times, siren will chirp once every 1.5sec. After
chirping 8 times, siren will continue sounding; parking lights will continuously
flash and disable the engine. (Press and hold button 2 for 2 sec before siren long
chirp to exit motorcycle-jacking mode.) During anti motorcycle-jacking mode,
siren will long chirp, when the key turns to OFF, siren will stop, and parking
lights will stop flashing as long as the ignition turns OFF. If key has been turned
to ON again, siren will sound and engine will not be able to start.
2．To exit anti motorcycle jacking: EMERGENCY OVERRIDE
EMERGENCY OVERRIDE
In arming mode or motorcycle-jacking mode, if transmitter is failed or lost, please refer to
following step for Emergency Override: Turn key to ON/OFF 5 times within 10 sec and
stay in ON position, LED shine for 2 seconds, then turn acc off, after LED start flashing,
after 1st digit of PIN code turn ACC ON, after ACC OFF, LED start flashing for 2nd
number of PIN code. Together with 4 digits which need be correct. Siren will chirp 4
times, parking light will flash 4 times to indicate the system is disarmed.
PIN NUMBER SETTING (FACTORY PRESET PIN NUMBER:4321)
In disarming mode, turn ignition ON/OFF 8 times within 15 sec, and stay in ON position.
LED shine for 2 seconds, turn ignition OFF within 10sec, LED will start blink slowly, and
input old 4 PIN NUMBER, if old 4 PIN NUMBER is correct, siren will chirp once, turn
ignition OFF, LED will start blink slowly, and input NEW 4 PIN NUMBER
When LED blink the 1st digit of PIN NUMBER, turn ignition ON, 1st PIN
NUMBER will be input, and turn ignition OFF, LED start to blink again
When LED blink the 2nd digit of PIN NUMBER, turn ignition ON, 2nd PIN
NUMBER will be input, and turn ignition OFF, LED start to blink again;
When LED blink the same number as the 3rd digit of PIN NUMBER, turn
ignition ON, 3rd PIN NUMBER will be input, and turn ignition OFF, LED
start to blink again,

Version1.2 TS MOTO
5
When LED blinks the fourth digit of PIN NUMBER, turn ignition ON, 4th
PIN NUMBER will be input, and turn ignition OFF.
5 sec. After 4 New PIN NUMBER has been input, LED will automatically
show the new PIN NUMBER to confirm: Blink 1st digit –pause 2 second-blink
2nd digit - pause 2 second…
Turn ignition ON, or 10 sec after new PIN NUMBER confirm, system will exit PIN
NUMBER setting mode.
Attention: when the inputed code is super code(8555),the old key will be
reset automatically.
VALET MODE
You can prevent your security system from automatically arming by using valet mode, this
is very useful when washing the motorcycle for example, in valet mode, the security
system will not arm, even with the transmitter, but any accessory functions will continue
to work normally.
ENTER VALET MODE:
Ignition ON, press and hold button 2+3 within 5 seconds, (the siren will chirp once even
the button was pressed once)，then unit will enter valet mode. In valet mode, press button
1, siren will chirp 3 times. LED quickly flashes 3 times and then cycle.
The same way to exit valet mode.
MEMORY FUNCTION
This security system will store its current state to non-volatile memory. If power is lost
and then reconnected the system will recall the stored state from memory. This means if
the unit is in valet mode and the battery is disconnected for any reason, such as servicing
the motorcycle, when the battery is reconnected the unit will still be in valet mode. This
applies to all states of the system including arm, disarm, and valet mode.
HIGH FREQUENCY
Your system transmits and receives at 433 MHz; this provides a cleaner spectrum with less
interference and a more stable signal.

Version1.2 TS MOTO
6
FUNCTION SELECTION
1. In disarming mode, turn ignition to ON, press and hold button 1+4 for 2 seconds
within 5 seconds，siren will chirp once, LED will flash once per second to
indicate system entered function selection.
2. Press button 3 once, siren will chirp once to indicate unit entered function
selection menu 1. Press button 3 twice, siren will chirp twice to indicate unit
entered function selection menu 2, press button 3 thrice, siren will chirp thrice to
indicate unit entered function selection menu 3.
3. After unit entered function menu, press button 1 once, siren will chirp twice to
indicate current setting is default value, press button 2 once, siren will chirp once
to indicate current setting is variable value. If siren chirps thrice to indicate the
sensitivity of tilt sensor is 30°. (Note: when the sensitivity is 30°, if user wants to
adjust higher sensitivity, to press button 1 once, and then press button 2 to adjust.
4. Ignition OFF to exit function selection menu. Siren will long chirp once
5. During the menu setting, if without any operation within 10 seconds, siren will
long chirp once to exit function selection menu.
NO FUNCTION SELECTION PRESET
(CHIRP TWICE)
VARABLE
(CHIRP ONCE)
1
AUTO REARMING
YES
NO
2
ANTI MOTORCYCLE-
JACKING NO YES
3 Tilt SENSOR sensitivity
adjustment 3(°) 1，2，3，4，5，7，9，
11，15，30(°)
4 Silent/chirp mode Silent Chirp mode
6 Positive/Negative siren
output Positive(constant)
Negative siren
output(pulse)
7
Flash lamp arm/disarm
Enable
Disable
8
Reset back to Factory
setting DEFAULT

Version1.2 TS MOTO
7
POWER SAVING MODE
a. After 6 hours in the armed state, the LED will flash once interval 4 seconds, after
12 hours, it will flash once interval 8 seconds
b. After 24 hours of no activity (arm, disarm, or alarm trigger) The alarms receiver,
and LED turn off
c. After 48 hours the alarm enters sleep mode to save as much battery power as
possible, the system is drawing next to no current in this mode.
d. If any other input is activated when in sleep mode, the system will wake up, the
siren will chirp 10 times.
APPENDIX
1. ELECTRICAL CONFIGURATIONS
DC Supply voltage
12V
DC Tolerance voltage 9V－16V
Current (Static) ≤6mA
Current (Sleep)
≤4mA
Siren volume 105dB

Version1.2 TS MOTO
8
2. INSTALLATION GUIDE
LAMP
FUSE 15A

Version1.2 TS MOTO
9
3. SMART UNITE SIZE