Kelvix DMX-25506 Manual

1Connect power supply, DMX signal, and LED lighting strip(s) to the DMX512 decoder as shown below:
2Once all connections have been made, set
decoder to desired DMX start address:
Power Supply
12-24VDC
LN
AC
RGBWCT, RGBWA or 2 RGB Lighting Strip
Note: Multiple decoders set to the same
DMX address will function in unison.
Note: The DMX-26506 decoder complies
tostandard DMX512 protocol and is
compatible with any third party standard
DMX512 controller.
DMX
CONTROLLER
a) Scan QR code for a time-saving online
conversion tool.
http://www.sabretechnology.co.uk/calc.asp
b) Manual Instructions:
Use DIP Switch to select adress. To set
DMX address, first look at the sideways
numbers printed below switching board
(1, 2, 4,... 256); These are DMX adresses.
To achieve desired address, add up these
values then flip corresponding switches to
“ON” position.
For example, desired DMX address is 40.
The value of switch 6 (DMX address 32) +
the value of switch 4 (DMX address 8) =
DMX value 40. Therefore, move switch 6 and
4 to the “ON” position (see example below).
1 2 3 4 5 6 7 8 9 10
ON
Refer to setup instructions of system’s DMX
controller for completion of setup.
3
Questions/Support | 800-789-3810 | [email protected] 072220DM
B- G- R- R- V-V+ V+ V+B- G-
OUTPUT POWER
DC5V-24V
MAX 16A
POWER/DMX
DMX IN
D+ D- GND
DMX ADDR AND FUN
DMX OUT
D+ D- GND
SETUP INSTRUCTIONS
DMX-26506
+24V +24V
R
RR
G
G
W
WB B
C
R
G
W
B
C
C
+24V
+24V
R
RR
G
G
W
W
B
B
C
R
G
W
B
C
C
All manuals and user guides at all-guides.com

1Ensure decoder is connected to power supply and RGBW or RGB Lighting strip as shown below:
2Using a small screwdriver, flip FUN
switch located on the dip switch board
to the “ON” position.
1 2 3 4 5 6 7 8 9 10
ON
FUN
3Follow instructions below to test various
color modes:
1 2 3 4 5 6 7 8 9 10
ON
FUN
a) To test red, flip switch 1 to the
“ON” position.
1 2 3 4 5 6 7 8 9 10
ON
FUN
b) To test green, flip switch 2 to the
“ON” position.
c) To test blue, flip switch 3 to the
“ON” position.
1 2 3 4 5 6 7 8 9 10
ON
FUN
d) To test white, flip switch 7 to the
“ON” position.
1 2 3 4 5 6 7 8 9 10
ON
FUN
Questions/Support | 800-789-3810 | [email protected] 072220DM
TESTING INSTRUCTIONS
DMX-26506
Power Supply
12-24VDC
LN
AC
RGBWCT, RGBWA or 2 RGB Lighting Strip
B- G- R- R- V-V+ V+ V+B- G-
OUTPUT POWER
DC5V-24V
MAX 16A
POWER/DMX
DMX IN
D+ D- GND
DMX ADDR AND FUN
DMX OUT
D+ D- GND
+24V +24V
R
RR
G
G
W
WB B
C
R
G
W
B
C
C
+24V
+24V
R
RR
G
G
W
W
B
B
C
R
G
W
B
C
C
All manuals and user guides at all-guides.com