Kent Euroclean Rainmaker C User manual

Electronic Service
Manuals
This electronic document is provided as a service to our custom-
ers. We do not create the contents of the information contained in
this document. Should you have detailed questions pertaining to
the information contained in this document, you may contact Michco,
or the manufacturer which provided the original information in this
electronic deliverable. Michco’s only part in this electronic deliver-
able was the electronic assembly process.
You may contact Michco through the following methods:
Phone [phone] or [phone] MI, OH, IN only
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: [phone]
Email: [email protected]
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email: [email protected]
By Fax: [phone]
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective
owners. Manuals are subject to Manufacturer’s reproduction limitations. Originals or reproductions were provided
by manufacturers through a request. We make no warranty as to the correctness of information provided in this
document and you assume all risk.

Instructions for use and parts list
Kent/Euroclean MODEL 56649980
06/03 revised 11/03 Form Number 56041562
Rainmaker™C

2 - FORM NO. 56041562 / Rainmaker™C
INTRODUCTION
This manual will help you get the most from your Kent/Euroclean RainmakerTM C. Read thoroughly
before operating the machine.
NOTE: Bold numbers in parenthesis indicate an item illustrated on page 7.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your authorized Kent/Euroclean Service Center, who
employs factory-trained service personnel, and maintains an inventory of Kent/Euroclean original
replacement parts and accessories.
Call the Kent/Euroclean DEALER named below for parts or service. Please specify the Model and
Serial Number when discussing your machine.
NAME PLATE
The Model and Serial Number of your machine are shown on the nameplate on the machine. This
information is needed when ordering repair parts for the machine. Use the space below to note the
Model and Serial Number of your machine for future reference.
MODEL : ________________________________________
SERIAL NUMBER : _____________________________________
UNCRATING
When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If
damage is evident, save the shipping carton so that it can be inspected. Contact Kent/Euroclean
Customer Service Department immediately to file a freight damage claim.
DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ THIS SECTION.
IMPROPER USE WILL VOID THE WARRANTY.
•Always use a defoamer when foaming occurs to prevent vacuum motor damage.
•Never use water above 140°F (60°C).
•Do not store outdoors. Avoid extremes in temperature.
•Do not let the pump run dry. Turn the pump off and refill that tank when cleaning solution
gets low.
•Use approved chemicals only. All chemicals should be mixed thoroughly. Liquid
chemicals are recommended to prevent powder buildups. A pH between 6 and 9 is
advised. The use of high alkaline detergents or strong acids will accelerate the wear of
the pump and seals, and will void the warranty.
•All extension cords must have a rating of at least 12/3 (#12 cord). Extension cords should
be no longer than 50 feet. Replace the plug immediately if the ground prong becomes
damaged or is broken off.
(Dealer, affix service sticker here)

FORM NO.56041562 / Rainmaker™C - 3
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
This machine is only suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices other than normal residential housekeeping purposes.
When using an electrical appliance, basic precautions should always be followed, including
the following:
Read all instructions before using this appliance.
WARNING!
To reduce the risk of fire, electric shock, or injury:
• Do not leave the appliance when it is plugged in. Unplug the unit from the outlet when not in
use and before servicing.
• To avoid electric shock, do not expose to rain. Store indoors.
• Do not allow to be used as a toy. Close attention is necessary when used near children.
• Use only as described in this manual. Use only the manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If the appliance is not working as it should be, has
been dropped, damaged, left outdoors or dropped into water, return it to a service center.
• Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the
cord around sharp edges or corners. Do not run the appliance over the cord. Keep the cord
away from heated surfaces.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not handle the plug, cord or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
• Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes,
or any health endangering dusts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids such as gasoline or use in areas
where they may be present.
• Connect to a properly grounded outlet only. See Grounding Instructions.
• Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure
or chemical content.

4 - FORM NO. 56041562 / Rainmaker™C
CONSIGNES DE SECURITE IMPORTANTES
Cette machine ne convient qu´à un usage industriel, par exemple dans des hôtels, écoles,
hôpitaux, usines, boutiques et bureaux et autres à l´exclusion de tout usage de maintenance
résidentielle normale.
L’utilisation d’un appareil électrique demande certaines précautions:
LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL)
AVERTISSEMENT!
Pour réduire les risques d’incendie, de choc électrique ou de blessure:
• Ne pas laisser l’appareil sans surveillance lorsqu’il est branché. Débrancher lorsque l’appareil
n’est pas utilisé et avant l’entretien.
• Pour réduire les risques de choc électrique, utiliser à l’intérieur seulement.
• Ne pas permettre aux enfants de jouer avec l’appareil. Une attention particulière est
nécessaire lorsque l’appareil est utilisé par des enfants ou à proximité de ces derniers.
• N’utiliser que conformément à cette notice avec les accessoires recommandés par le fabricant.
• Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner l’appareil à un atelier de
réparation s’il ne fonctionne pas bien, s’il est tombé ou s’il a été endommagé, oublié à l’extérieur
ou immergé.
• Ne pas tirer soulever ou traîner l’appareil par le cordon. Ne pas utiliser le cordon comme une
poignée, le coincer dans l’embrasure d’une porte ou l’appuyer contre des arêtes vives ou des
coins. Ne pas faire rouler l’appareil sur le cordon. Garder le cordon à l’écart des surfaces
chaudes.
• Ne pas débrancher en tirant sur le cordon. Tirer plutôt la fiche.
• Ne pas toucher la fiche ou l’appareil lorsque vos mains sont humides.
• N’insérer aucun objet dans les ouvertures. Ne pas utiliser l’appareil lorsqu’une ouverture est
bloquée. S’assurer que de la poussière, de la peluche, des cheveux ou d’autres matières ne
réduisent pas le débit d’air.
• Maintenir les cheveux, les vêtements amples, les doigts et toutes les parties du corps à l’écart des
ouvertures et des pièces mobiles.
• Ne pas aspirer de matières en combustion ou qui dégagent de la fumée, comme des cigarettes,
des allumettes ou des cendres chaudes.
• Mettre toutes les commandes à la position ARRÊT avant de débrancher l’appareil.
• User de prudence lors du nettoyage des escaliers.
• Ne pas aspirer des liquides inflammables or combustibles, comme de l’essence, et ne pas faire
fonctionner dans des endroits ou peuvent se trouver de tels liquides.
• Ne brancher qu’à une prise de courant avec mise à la terre. Voir les instructions visant la mise à
la terre.
• Le liquide qui sort de l’embout de vaporisation peut s’avérer dangereux en raison de sa
température, de sa pression ou du produit chimique qu’il contient.
CONSERVER CES INSTRUCTIONS

FORM NO.56041562 / Rainmaker™C - 5
120VAC GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should electrically malfunction, grounding provides a path of
least resistance for electric current to reduce the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged
into an appropriate outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
DANGER!
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug provided with the appliance. If it will not fit the outlet, have
a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the
plug illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and 3 may be used to
connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not
available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can
be installed by a qualified electrician. The green-colored rigid ear, tab, or the like extending from the
adapter must be connected to a permanent ground such as a properly grounded outlet box cover.
Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not
approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire
must be attached to the grounding pin only.
Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong
plugs and outlets. DO NOT use extension cords more than 50 feet (15 m) long.
PLEASE NOTE: FOR NORTH AMERICA ONLY

6 - FORM NO. 56041562 / Rainmaker™C
INSTRUCTIONS VISANT LA MISE À LA TERRE (120VAC)
Cet appareil doit être mis à la terre. En cas de défaillance ou de panne éventuelles, la mise a la terre
fournit au courant un chemin de moindre résistance qui réduit le risque de choc électrique. Cet
appareil est pourvu d’un cordon muni d’un conducteur de terre et d’une fiche avec broche de terre.
La fiche doit être branchée dans une prise appropriee correctement installée et mise à la terre
conformément aux règlements et ordonnances municipaux.
AVERTISSEMENT !
Un conducteur de terre mal raccordé peut entraîner un risque de choc électrique. Consulter un
électricien ou un technicien d’entretien qualifié si vous n’êtes pas certain que la prise est correctement
mise à la terre. Ne pas modifier la fiche fournie avec l’appareil - si elle ne peut être insérée dans la
prise, faire installer une prise adéquate par un électricien qualifié.
Cet appareil est destiné à un circuit de 120 V et est muni d’une fiche de terre semblable à celle
illustrée par le croquis 1. Un adaptateur temporaire semblable à celui illustré par le croquis 2 et C
peut être utilisé pour brancher cette fiche à une prise bipolaire comme l’illustre le croquis 2 si une
prise avec mise à la terre n’est pas disponible. L’adaptateur temporaire devrait etre utilisé seulement
jusqu’à ce qu’une prise avec mise à la terre soit installée par un électricien qualifié. L’oreille rigide ou
le crochet ou autre dispositif semblable, de couleur verte, prolongeant l’adaptateur doit Iêtre raccordé
à un élément correctement mis à la terre comme le couvercle d’une boîte de sortie mise à la terre.
L’adaptateur doit être fixé par une vis métallique. Note: Au Canada, I’utilisation d’un adaptateur
temporaire n’est pas autorisée par le Code canadien de l’électricité.
Remplacez la prise si la prise de terre est abîmée ou cassée.
Le fil Vert (ou Vert/Jaune) dans la ganse est le fil de terre. Lors du remplacement d´une prise, ce fil
doit être raccordé à la prise de terre uniquement.
Les ralonges connectées à cette machine doivent avoir 12 mesures, trois ganses de fil ayant trois
fiches masculines féminines tree-prong plugs and outlets. N´UTILISEZ PAS de ralonge de plus de 15
m (50 pieds) de long.
VEUILLEZ NOTER: CES INSTRUCTIONS CONCERNENT UNIQUEMENT L’AMÉRIQUE DU
NORD

FORM NO.56041562 / Rainmaker™C - 7
KNOW YOUR MACHINE
KNOW YOUR MACHINE DESCRIPTIONS
Operator Handle (1) - Operator holds this to move the machine from one location to another.
Lift Handle (2) - Operator grasps this handle when lifting the machine.
Solution Tank Lid (3) - Fill Solution Tank here with warm water and chemicals.
Recovery Tank Lid (4) - The Recovery Tank can be flushed out by running clean water into this
opening with the Recovery Tank Drain Hose open. The vacuum float Shut-OFF can also be
accessed through this opening for maintenance.
Switch Plate (5) - The switches that operate the motors are located here, as well as indicator
lights for the heater.
Vacuum Hose Connector (6) - This is where the vacuum hose attaches to the machine.
Solution Hose Connector (7) - This is where the solution hose attaches to the machine.
Latches (8) - These latches can be opened if the base compartment needs to be accessed. The
latches are normally closed to keep the machine sections held together tightly.
Drain Gate (9) - This gate is opened to allow the dirty recovered water to empty.
1
2
3
4
5
6
8
7
9

8 - FORM NO. 56041562 / Rainmaker™C
I I
O O
I
O
➀➀
➀➀
➀➁➁
➁➁
➁➂➂
➂➂
➂
SWITCH PLATE DESCRIPTIONS
Vacuum Switches (1 and 2) - These switches each turn one vacuum on and off. The
switches will light when ON.
Pump Switch (3) - This switch turns the pump on and off. The switch will light when ON.
Power
Cord
∼
115V
Green
SW VAC 1
VAC 2
Line
FAN
PUMP
Neutral
SW
SW
White
Black
White
WIRING DIAGRAM
White
White
White
White
Black
Black
Black
Black

FORM NO.56041562 / Rainmaker™C - 9
OPERATION
1Inspect the machine, hoses, and cleaning tool(s) for cleanliness and completeness.
2Fill the solution tank with warm water. Using warm water may be a benefit in cleaning
effectiveness, but do not use hot water (above 140°F / 60°C) in the tank. Add liquid
cleaning solution with a pH of between 6 and 9.
3Plug in the power cord.
4Attach the spray hose to the solution quick disconnect and the vacuum hose to the hose barb
on the recovery tank. Attach the other ends of the hoses to the cleaning tool.
5Turn the pump on. Turn the vacuums on.
6Begin cleaning using the correct hoses and tool. NOTE: the pump has a built in pressure
switch; the pump only runs when you are spraying.
7Use defoamer in the recovery tank if foaming occurs.
8Monitor the water level in the solution tank. Do not let the pump run dry.
9When the solution tank gets low on fluid, turn the pump and vacuums off, fill the solution tank,
empty and clean the recovery tank.
10 When finished with the job, remove any unused solution from the solution tank, and run a tank
of clean water through the system.
BALL FLOAT VACUUM SHUT-OFF
Prior to using the machine, always check that the float filter is clean and the ball can travel freely.
When the recovery tank is full, the ball float will rise and will shut off the vacuum flow to prevent any
more water from entering the tank. Turn off the vacuum, and empty the recovery tank. NOTE: if
foam is present, or, if the ball float is prevented from rising, the float will not be able to stop the air
flow, and the tank might over fill.
CAUTION!
To avoid vacuum motor damage, always make sure the float filter is clean and the ball can travel
freely prior to using the machine. And always use a defoamer when foaming occurs.

10 - FORM NO. 56041562 / Rainmaker™C
USE AND MAINTENANCE
1Use only liquid chemicals with a pH between 6 and 9 at the recommended mix ratios. Improper
chemicals, or improperly mixed chemcials, can cause possible damage to the pump, seals, and
other components.
2Turn the pump “off” when the solution tank is low on fluid. Do not let the pump run dry.
3Regularly clean any mineral or chemical deposits in the heat exchanger, lines and pump with a
mild acid descaler.
4Prior to each job, inspect, and clean if needed, the solution filter, the recovery tank float filter,
and the drain gate.
5Make sure the airways are not blocked before each use.
6Inspect the carbon brushes on the vacuum motors once a year. Replace if worn down.
7Clean the recovery tank daily. Clean the body and wheels as needed.
8Keep the machine from extremes in temperatures.
MAINTENANCE SCHEDULE
Daily Monthly Yearly
PMUP&SENILHSULF X
RETLIFTAOLFMUUCAVNAELC X
RETLIFNOITULOSNAELC X
SYAWRIATELNIKCEHC X
ENIHCAMELACSED X
SEHSURBROTOMMUUCAVKCEHC X

FORM NO.56041562 / Rainmaker™C - 11
NOTES:

12 - FORM NO. 56041562 / Rainmaker™C

FORM NO.56041562 / Rainmaker™C - 13
PART LIST RAINMAKERTM C
Item Ref. No. Qty Description
1 56102816 4 Bolts, 1/4-20 X 3/4", Flat Head (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
2 56102843 1 Handle, Chrome
3 56108096 1 Guard, For Fan (Fan Kit)(Fan Kit)
(Fan Kit)(Fan Kit)
(Fan Kit)
4 56108096 1 Fan, 120V (Fan Kit)(Fan Kit)
(Fan Kit)(Fan Kit)
(Fan Kit)
4A 56102816 4 Screw, 6-32 X 2” (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
5 56102816 4 Locknut, 6-32 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
6 56102810 1 Base Compartment, Gray
7 56102845 2 Louver, Includes Screws
8 56649989 1 PVC Reducer (Cord Retainer Kit)(Cord Retainer Kit)
(Cord Retainer Kit)(Cord Retainer Kit)
(Cord Retainer Kit)
9 56102850 2 Hinge Pin
10 56102847 1 Axle Rod, Plated, 1/2 x 18.25”
11 56102811 2 Wheel, 10" (Wheel Kit)(Wheel Kit)
(Wheel Kit)(Wheel Kit)
(Wheel Kit)
12 56102811 2 Axle Cap (Wheel Kit)(Wheel Kit)
(Wheel Kit)(Wheel Kit)
(Wheel Kit)
14 56108074 2 Latch, Rubber, With Strike
14A 56102816 8 Screw, 8-32 X 1/2” (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
15 56102839 1 Hose, 3/8" ID x 76” LG
16 56649985 1 Pump, 100 PSI, 120V
17 56102817 4 Hose Clamp (Hose Clamp Kit)(Hose Clamp Kit)
(Hose Clamp Kit)(Hose Clamp Kit)
(Hose Clamp Kit)
18 56102829 2 Hose Barb/Elbow (Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)
19 56102829 1 Hose Barb, Brass, 1/4 N.P.T. (Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)
20 56102829 1 Elbow, Brass (Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)
21 56102836 1 Quick Disconnect, Male, 1/4 N.P.T.
(Quick Disconnect Kit)(Quick Disconnect Kit)
(Quick Disconnect Kit)(Quick Disconnect Kit)
(Quick Disconnect Kit)
22 56102836 4 Washer, Brass (Quick Disconnect Kit)(Quick Disconnect Kit)
(Quick Disconnect Kit)(Quick Disconnect Kit)
(Quick Disconnect Kit)
23 56102848 2 Castor, 4”, No Brake
24 56102842 2 Manifold
25 56102818 2 Gasket, Vacuum Motor (V(V
(V(V
(Vacuum Motor Kit)acuum Motor Kit)
acuum Motor Kit)acuum Motor Kit)
acuum Motor Kit)
26 56102815 1 Bracket, Vacuum Mounting (Bracket Kit)(Bracket Kit)
(Bracket Kit)(Bracket Kit)
(Bracket Kit)
27 56102816 6 Bolt, 1/4-20 X 5", Fully Threaded (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
28 56102816 6 Washer, 1/4, Split Lock (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
29 56102816 6 Nut, Finish, 1/4 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
30 56102816 18 Washer, Flat, 3/16 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
31 56102816 18 Lock Nut, 1/4 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
31A 56102816 4 Bolt, 1/4-20 X 1-1/4" (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
32 56102818 2 Vacuum Motor, 120V (V(V
(V(V
(Vacuum Motor Kit)acuum Motor Kit)
acuum Motor Kit)acuum Motor Kit)
acuum Motor Kit)
33 56102817 4 Hose Clamp (Hose Clamp Kit)(Hose Clamp Kit)
(Hose Clamp Kit)(Hose Clamp Kit)
(Hose Clamp Kit)
34 56102841 1 Hose, Exhaust, 2", Ribbed x 41” LG
35 56108052 1 Float, Ball & Cage On Manifold
35A 56108053 1 PVC Elbow
36 56108054 2 Chain, 8" (also included in Solution Lid Kit 56102812)(also included in Solution Lid Kit 56102812)
(also included in Solution Lid Kit 56102812)(also included in Solution Lid Kit 56102812)
(also included in Solution Lid Kit 56102812)
37 56108055 1 Lid, 6", Clear Center, W/Ring
38 56102816 1 Gasket (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
39 56102816 8 Bolt, 1/4-20 X 3/4” (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
40 56102816 6 Screw, 8-32 X .88 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
41 56102816 6 Lock Nut, 8-32 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
42 56102812 1 Screw, 10-32 X 3/8", Brass (Solution Lid Kit)(Solution Lid Kit)
(Solution Lid Kit)(Solution Lid Kit)
(Solution Lid Kit)
42A 56102816 1 Bolt, 10-32 X 5/8” (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
43 56649987 1 O-Ring, Large (Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)
43A 56649987 1 O-Ring, Small (Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)
Item Ref. No. Qty Description
43B 56649987 1 Nut, 1-1/2”, Aluminum (Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)
44 56649987 1 Drain Gate (Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)
45 56649987 1 Spout (Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)(Drain Gate Kit)
(Drain Gate Kit)
46 56649989 1 Cord Retainer (Cord Retainer Kit)(Cord Retainer Kit)
(Cord Retainer Kit)(Cord Retainer Kit)
(Cord Retainer Kit)
47 56649988 1 Cord, 12/3, 25 Ft
48 56102815 1 Bracket, Mating (Bracket Kit)(Bracket Kit)
(Bracket Kit)(Bracket Kit)
(Bracket Kit)
49 56108061 1 Vac Inlet Hose Barb
50 56102815 1 Bracket, Mating, With Hole (Bracket Kit)(Bracket Kit)
(Bracket Kit)(Bracket Kit)
(Bracket Kit)
51 56102812 1 Lid, Solution Tank (Solution Lid Kit)(Solution Lid Kit)
(Solution Lid Kit)(Solution Lid Kit)
(Solution Lid Kit)
52 56102853 1 Filter, Pump Inlet
53 56102854 1 Nipple, PVC, 1/2 N.P.T.
54 56649984 1 Solution Tank, Blue
55 56649983 1 Recovery Tank, Blue
56 56102829 1 Hose Barb, Straight, Nylon (Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)(Hose Barb Kit)
(Hose Barb Kit)
57 56102816 4 Bolt, 1/4-20 X 1" Allen Head (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
58 56102816 4 Washer, 1/4, SS Flat (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
59 56102856 2 Cord Wrap, Black
60 56102855 1 Switch Plate
62 56102827 3 Switch, SPST, W/Cover
63 56102816 5 Screw, #4 X 3/8" (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
64 56102844 1 Flange, Exhaust
65 56102860 1 Gasket, 7 Ft
66 56649986 2 Label, Kent Euroclean
67 56102816 3 Screw, 10-32 X 5/8” (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
68 56102816 3 Lock Nut, 10-32 (Hardware Kit)(Hardware Kit)
(Hardware Kit)(Hardware Kit)
(Hardware Kit)
* 56108093 1 Label, Warning
* = Not Shown
KITS
56108096 1 Fan Kit (#3, 4)
56102811 1 Wheel Kit (1 each of #11, 12)
56102812 1 Solution Lid Kit (#42, 51 / also includes #36)
56102816 1 Hardware Kit
(#1, 4a, 5, 14a, 27-31a, 38-41, 42a, 57, 58, 63, 67, 68)
56102817 1 Hose Clamp Kit (#17, 33)
56102818 1 Vacuum Motor kit (1 each of #25, 32)
56649987 1 Drain Gate Kit (#43-45)
56649989 1 Cord Retainer Kit (#8, 46)
56102829 1 Hose Barb Kit (#18-20, 56)
56102836 1 Quick Disconnect Kit (#21, 22)
56102815 1 Bracket Kit (#26, 48, 50)
ACCESSORIES
56102804 1 Single Bend Wand Assembly
56102805 1 Double Bend Wand Assembly
56102807 1 Extractor Hand Tool
56102861 1 Vac Hose / Pressure Line 25ft.
56102871 1 Vac Hose / Pressure Line 15ft.
revised 11/03

14 - FORM NO. 56041562 / Rainmaker™C
TECHNICAL SPECIFICATIONS
Two, 2-Stage
150”
100 cfm
15 amps
Rotationally molded polyethylene
14 Gal. (53 L)
12 Gal.(45.4 L)
100 psi
15 ft. (4.5 m)
15 ft. (4.5 m)
One 25 ft. (7.6 m), High visibility yellow
10 in. (25 cm)
4 in. (10.2 cm)
38 in. (96.5 cm)
36 in (91.4 cm)
17.6 in (44.7 cm)
78 lb (35 kg)
Vacuum Motor:
Water lift:
Air Flow:
Amp Draw:
Tank Construction:
Solution Tank Capacity:
Recovery Tank Capacity:
Application Flow:
Solution Hose Length:
Recovery Hose Length:
Power Cord:
Rear Wheels:
Front Castors:
Height:
Length:
Width:
Machine weight:

FORM NO.56041562 / Rainmaker™C - 15
NOTES

.
NOTE: There should be
no voltage reading when
switch is “OFF” (Step 3).
FIGURE 1
VACUUM BALL-FLOAT SYSTEM
TROUBLESHOOTING
(120V)
NOTE: The motors on these extractor models are controlled by AC voltage passing through the ON/OFF
switch.
VACUUM MOTOR NOT RUNNING:
1. Always unplug the machine before working on the wiring system.
2. Open the machine to look for damaged or disconnected wires leading to the vac motor.
3. Remove the screws from the switch plate. Gently turn the switch plate over and check
the back of the switches to make sure no wires have pulled loose.
MEASURING THE AC VOLTAGE THROUGH THE SWITCH:
1. Connect a voltmeter to the terminals (with wires) on the vacuum switch being tested. Set
the AC voltage in the range of 120 volts, or more. (See Figure 1 to the right).
2. Turn the vacuum switch “OFF”.
3. With the switch in the “OFF”
position, plug the #1 Cord (red
sleeve) into an outlet and
measure for NO AC voltage.
4. Turn the switch “ON” and look
for an AC voltage reading. (See
Figure 1 to the right).
5. If the switch is not
working, replace it.
Refer to the
schematic and parts list for the
particular machine you are
working on.
6. If the switch is working correctly,
test the motor itself by connecting
it directly to AC voltage.
Switch ON
Opposite sides
of the switch

TESTING THE MOTOR DIRECTLY TO AC VOLTAGE:
1. Unplug the power cords.
2. Cut both the power wires leading from the vacuum motor, several inches from the motor
itself. Leave enough length for reconnecting the wires.See Figure 2 below.
3. Connect the motor wires (leading from the motor) to an AC jumper wire. See Figure 2.
4. Plug the jumper into an outlet. Does the vacuum motor run? If the vacuum motor runs,
unplug the jumper, visually inspect and/or use the “continuity tester” or “ohm meter” to
find the opening between the switch and motor wires. Refer to the wiring schematic for
your machine model.Repair.
5. If the motor does not run, replace it.Refer to the parts list and schematic for your machine
for the correct part number. Refer to Vacuum Motor Replacement Instructions for steps
on removal and installation.
FIGURE 2 NOTE: Do not remove the mo-
tor to test.
Step 2 & 3: Cut both power wires sev-
eral inches from the motor and con-
nect to an AC jumper wire.
Step 5: Plug the jumper
into an outlet.
NOTE: Do not remove the
motor to test it.

.
NOTE: There should be
no voltage reading when
switch is “OFF” (Step 3).
FIGURE 1
VACUUM BALL-FLOAT SYSTEM
TROUBLESHOOTING
AquaPro
TM
300
(120V)
NOTE: The motors on these extractor models are controlled by AC voltage passing through the ON/OFF
switch.
VACUUM MOTOR NOT RUNNING:
1. Always unplug the machine before working on the wiring system.
2. Open the machine to look for damaged or disconnected wires leading to the vac motor.
3. Remove the screws from the switch plate. Gently turn the switch plate over and check
the back of the switches to make sure no wires have pulled loose.
MEASURING THE AC VOLTAGE THROUGH THE SWITCH:
1. Connect a voltmeter to the terminals (with wires) on the vacuum switch being tested. Set
the AC voltage in the range of
120 volts, or more. (See Figure
1 to the right).
2. Turn the vacuum switch “OFF”.
3. With the switch in the “OFF”
position, plug the #1 Cord (red
sleeve) into an outlet and
measure for NO AC voltage.
4. Turn the switch “ON” and
look for an AC voltage
reading. (See Figure
1 to the right).
5. If the switch is not working,
replace it. Refer to the
schematic and parts list for the
particular machine you are
working on.
6. If the switch is working correctly,
test the motor itself by connecting
it directly to AC voltage.
Switch ON
Opposite sides
of the switch