Kent Euroclean SelectGloss 21PH Installation and maintenance instructions

Electronic Service
Manuals
This electronic document is provided as a service to our custom-
ers. We do not create the contents of the information contained in
this document. Should you have detailed questions pertaining to
the information contained in this document, you may contact Michco,
or the manufacturer which provided the original information in this
electronic deliverable. Michco’s only part in this electronic deliver-
able was the electronic assembly process.
You may contact Michco through the following methods:
Phone [phone] or [phone] MI, OH, IN only
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: [phone]
Email: [email protected]
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email: [email protected]
By Fax: [phone]
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective
owners. Manuals are subject to Manufacturer’s reproduction limitations. Originals or reproductions were provided
by manufacturers through a request. We make no warranty as to the correctness of information provided in this
document and you assume all risk.

10/02 revised 5/04 Form Number 56041536
SelectGloss
™
21PH, 21PK
OPERATOR MANUAL AND PARTS LIST
Kent/Euroclean MODELS 56649654(21PH), 56649655(21PK)
56649656(27PK), 56649657(27PO / OBS), 56649930(27PR)
SelectGloss
™
27PK, 27PO, 27PR

22
22
2 - FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR
IMPORTIMPORT
IMPORTIMPORT
IMPORTANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONS
This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices
other than normal residential housekeeping purposes.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Please read and adhere to all of the following Instructions before operating propane equipment.
1 The fuel supply system and cylinder connections of the floor maintenance machine shall be checked for leakage
immediately after a cylinder is connected.
2 Connection and disconnection of cylinders shall be done in a well ventilated area with no source of ignition with
10 ft. (3m) from the point of connection.
3 When the engine of a floor maintenance machine is running the operator shall not leave the unit unattended.
4 When a floor maintenance machine is not in use and stored indoors, the cylinder shall be removed and stored
outdoors and protected from damage and tampering.
5 A sign indicating “NO SMOKING” shall be permanently displayed at the storage area. The sign shall be in
accordancewiththe signrequiredIn Clause10.12.3ofCAN/CGA-b149.2-M91, PropaneInstallationCode. (Doesnot
apply in industrial buildings).
6 When the cylinder is attached to the floor maintenance machine for use, the operator shall not leave the unit
unattended except for short periods of time such as rest stops, washroom or meal stops.
7 A floor maintenance machine shall only be used In buildings:
a. providedwithcontinuousmechanicalventilation thatremovestheproductsof combustionto theoutdoorsofnot
less than 300 CFM for each 10,000 Btu input or fraction thereof;
b provided with natural ventilation of not less than 300 CFM for each 10,000Btu input or fraction thereof, based on
a maximum of one quarter air change per hour for the net building volume.
8 The owner of a floor maintenance machine must ensure that the operator has participated in a course authorized
by the manufacturer of the unit on the safe handling of propane and the safe operation of the machine.
9 The owner of a floor maintenance machine shall ensure that the unit is maintained in accordance with the
manufacturer’s recommended maintenance procedures in a safe operating condition and the owner shall
maintain a record of the maintenance for a period of two years.
10 Before transporting a floor machine, the cylinder shall be securely fastened, with the system valve closed and the
cylinder shall be located in a well ventilated space.
SASA
SASA
SAVE THESE INSTRUCTIONSVE THESE INSTRUCTIONS
VE THESE INSTRUCTIONSVE THESE INSTRUCTIONS
VE THESE INSTRUCTIONS

FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR - 33
33
3
SAFETY PRECAUTIONSSAFETY PRECAUTIONS
SAFETY PRECAUTIONSSAFETY PRECAUTIONS
SAFETY PRECAUTIONS
This LPG (Liquefied Petroleum Gas) machine is intended for commercial
use; It is designed to clean floors. Do not use the machine other than
described in this Operator Manual.
All operators must read, understand and practice the following safety
precautions:
The following safety alert symbol is used throughout this manual as
indicated in their descriptions.
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
To warn of hazards or unsafe practices that could result In
severe personal Injury or death.
CAUTION!CAUTION!
CAUTION!CAUTION!
CAUTION!
To Identify actions that must be followed for safety opera-
tion of equipment.
The following information signals potentially dangerous conditions to
the operator of equipment.
1. DO NOT OPERATE:1. DO NOT OPERATE:
1. DO NOT OPERATE:1. DO NOT OPERATE:
1. DO NOT OPERATE:
* Unless trained and authorized.
* Unless operator manual Is read and understood.
* If It Is not In proper operating condition.
2. BEFORE OPERATING MACHINE:2. BEFORE OPERATING MACHINE:
2. BEFORE OPERATING MACHINE:2. BEFORE OPERATING MACHINE:
2. BEFORE OPERATING MACHINE:
* Check for fuel oil and liquid leaks. If leakage Is detected, shut off
fuel supply at tank Immediately.
* Keep sparks and open flame away from refueling area.
* Make sure area Is well ventilated.
* Remove any loose objects on floor .
3. WHEN OPERATING MACHINE:3. WHEN OPERATING MACHINE:
3. WHEN OPERATING MACHINE:3. WHEN OPERATING MACHINE:
3. WHEN OPERATING MACHINE:
* Always wear eye protection.
* Always use extreme caution when maneuvering.
* If you smell gas: shut off LPG valve immediately, open windows,
do not touch any electrical switches, extinguish any open flame
and immediately call your gas supplier .
* Do not smoke or allow smoking in the vicinity.
* Go slow on inclines and slippery surfaces.
* Donotplaceflammableobjectssuchasfuel,matches, etc., close
to the engine.
* Report machine damage or faulty operation immediately.
* Do not run continually over one minute In the park or tilted back
position, longer periods will affect oil flow and cause damage to
the engine.
* Be careful not to touch the muffler.
* Do not leave machine unattended while engine Is running.
* Keep hands, feet, hair, and loose clothing, etc. away from revolv-
ing pad and pulleys.
* Do not attempt to change pad while engine Is running.
4. BEFORE LEAVING MACHINE:4. BEFORE LEAVING MACHINE:
4. BEFORE LEAVING MACHINE:4. BEFORE LEAVING MACHINE:
4. BEFORE LEAVING MACHINE:
* Stop on level surface.
* Remove key (If applicable).
* Turn off LPG valve on tank.
5. WHEN SERVICING MACHINE:5. WHEN SERVICING MACHINE:
5. WHEN SERVICING MACHINE:5. WHEN SERVICING MACHINE:
5. WHEN SERVICING MACHINE:
* Keep hair, hands, feet, clothing, etc., away from moving parts.
* Wear eye and ear protection when using pressurized air or
water .
* Keep flames and sparks away from fuel system service area.
Keep area well ventilated.
* Do not smoke or allow smoking In the vicinity.
* Neveruse non-U.L. listedfueltank or componentasa substitute.
* Use manufacturer supplied or approved replacement parts.
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
Engine emits toxic gases. Severe respiratory damage or
asphyxiation can result. Provide adequate ventilation.
Consult with your regulatory authorities for exposure lim-
its. Keep engine properly tuned.
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
LP gas Is extremely flammable and is explosive under
certain conditions.
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
Machine moves when motor is running. Stop motor before
leaving machine.
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
Do not store machine outdoors and avoid getting wet.
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
The use of supplies other than those recommended by
manufacturer may cause damage.

44
44
4 - FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR
TT
TT
TABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS..............................................................................
..............................................................................
....................................... 22
22
2
SAFETY PRECAUTIONSSAFETY PRECAUTIONS
SAFETY PRECAUTIONSSAFETY PRECAUTIONS
SAFETY PRECAUTIONS ............................................................................................................................
............................................................................................................................
.............................................................. 33
33
3
INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION ......................................................................................................................................................
......................................................................................................................................................
........................................................................... 44
44
4
MACHINE SETUPMACHINE SETUP
MACHINE SETUPMACHINE SETUP
MACHINE SETUP ................................................................................................................................................
................................................................................................................................................
........................................................................ 55
55
5
CHECKING OIL LEVEL AND FILTERS .......................................... 5
ADJUSTING HANDLE HEIGHT .................................................... 5
INSTALLING OR CHANGING LPG FUELTANK .......................... 5
INSTALLING OR REMOVING
PAD DRIVER AND PADS .............................................................. 5
MACHINE OPERATIONMACHINE OPERATION
MACHINE OPERATIONMACHINE OPERATION
MACHINE OPERATION ..............................................................................................................................
..............................................................................................................................
............................................................... 66
66
6
STARTING MACHINE ................................................................... 6
OPERATING ELECTRIC CLUTCH (OPTIONAL)........................... 6
STOPPING MACHINE ................................................................... 6
EMERGENCY STOPPING .............................................................. 6
WHILE OPERATING MACHINEWHILE OPERATING MACHINE
WHILE OPERATING MACHINEWHILE OPERATING MACHINE
WHILE OPERATING MACHINE ......................................................................................................
......................................................................................................
................................................... 66
66
6
MAINTENANCEMAINTENANCE
MAINTENANCEMAINTENANCE
MAINTENANCE ......................................................................................................................................................
......................................................................................................................................................
........................................................................... 77
77
7
DAILY MAINTENANCE ................................................................. 7
WEEKLY MAINTENANCE ............................................................. 7
MONTHLY MAINTENANCE ......................................................... 7
QUARTERLY MAINTENANCE ...................................................... 7
LIFE OF MACHINE ......................................................................... 7
FUEL SYSTEM ................................................................................ 7
CHANGING THE OIL ...................................................................... 7
ADJUSTING BELT TENSION ....................................................... 8
REFUELING AND STORING TANKSREFUELING AND STORING TANKS
REFUELING AND STORING TANKSREFUELING AND STORING TANKS
REFUELING AND STORING TANKS ......................................................................................
......................................................................................
........................................... 88
88
8
REFUELING LP GAS TANKS......................................................... 9
STORING LP GAS TANKS ............................................................ 9
STORING MACHINESTORING MACHINE
STORING MACHINESTORING MACHINE
STORING MACHINE ........................................................................................................................................
........................................................................................................................................
.................................................................... 1010
1010
10
TRANSPORTING MACHINETRANSPORTING MACHINE
TRANSPORTING MACHINETRANSPORTING MACHINE
TRANSPORTING MACHINE ................................................................................................................
................................................................................................................
........................................................ 1010
1010
10
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE ............................................................................................................
............................................................................................................
...................................................... 1111
1111
11
STANDARD PARTSSTANDARD PARTS
STANDARD PARTSSTANDARD PARTS
STANDARD PARTS
21PH HONDA .................................................................................. 12
21PK KAWASAKI ........................................................................... 12
27PO ONAN P248 (20HP) .............................................................. 14
27PK KAWASAKI ........................................................................... 14
27PR ROBIN .................................................................................... 16
ROBIN ZXV 653 ENGINE ............................................................... 18
ROBIN ZXV 653 CARBURETION SYSTEM ................................. 20
KAWASAKI AUTOMATIC SHUT DOWN SYSTEM ................... 22
HONDA FUEL SYSTEM ................................................................. 24
KAWASAKI FUEL SYSTEM .......................................................... 25
ROBIN FUEL SYSTEM ................................................................... 26
ELECTRIC CLUTCH ASSY ............................................................. 27
KILL SWITCH ASSY ....................................................................... 28
KAWASAKI FUEL LOAD BLOCK .................................................. 29
KAWASAKI SCHEMATIC & HARNESS ...................................... 30
INTRODUCTIONINTRODUCTION
INTRODUCTIONINTRODUCTION
INTRODUCTION
This manual will help you get the most from your Kent / Euroclean™Kent / Euroclean™
Kent / Euroclean™Kent / Euroclean™
Kent / Euroclean™
SelectGloss™SelectGloss™
SelectGloss™SelectGloss™
SelectGloss™. Read it thoroughly before operating the machine.
This product is intended for commercial use only.
PP
PP
PARTS AND SERVICEARTS AND SERVICE
ARTS AND SERVICEARTS AND SERVICE
ARTS AND SERVICE
Repairs, when required, should be performed by Kent / Euroclean
service personnel using Kent / Euroclean original replacement parts
and accessories.
Call Kent / Euroclean for repair parts or service. Please specify the
Model and Serial Number when discussing your machine.
NAME PLANAME PLA
NAME PLANAME PLA
NAME PLATETE
TETE
TE
The Model and Serial Number of your machine are shown on the
Nameplate on the machine. This information is needed when ordering
repairparts forthe machine. Usethe spacebelow tonote theModel and
Serial Number of your machine for future reference.
MODEL NUMBER
SERIAL NUMBER
UNCRAUNCRA
UNCRAUNCRA
UNCRATINGTING
TINGTING
TING
When the machine is delivered, carefully inspect the shipping carton
and the machine for damage. If damage is evident, save the shipping
carton so that it can be inspected. Contact the Kent / Euroclean
Customer Service Department immediately to file a freight damage
claim.
revised 03-6

FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR - 55
55
5
MACHINE SET UPMACHINE SET UP
MACHINE SET UPMACHINE SET UP
MACHINE SET UP
CHECKING OIL LEVEL AND FILCHECKING OIL LEVEL AND FIL
CHECKING OIL LEVEL AND FILCHECKING OIL LEVEL AND FIL
CHECKING OIL LEVEL AND FILTERSTERS
TERSTERS
TERS
1 Check oil level prior to starting machine. Use proper amount and
specified oil, in order to prevent engine damage. When filling or
changing oil, add more than one quart (946.3ml) -then check dip
stick In cap. Add additional oil If necessary but do not overfull
The manufacturer recommends the use of 10W30 oil. ALWAYS CHECK
OIL DAILY BEFORE USING MACHINE.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
When checking oil, machine should be turned OFF and on level surface.
Remove dipstick and wipe clean, then replace dipstick. For Honda,
Kawasaki and Robin the cap should not be screwed In. To check Onan
engine,the capmust bescrewed Inall theway.ALWAYSREFERTOYOUR
ENGINE MANUAL.
2 Be sure air filter Is free of dust/debris and other obstructions.
3 Check and clean recoil and carburetor filters If necessary. (See
Engine Owners Manual)
ADJUSTING HANDLE HEIGHTADJUSTING HANDLE HEIGHT
ADJUSTING HANDLE HEIGHTADJUSTING HANDLE HEIGHT
ADJUSTING HANDLE HEIGHT
Machine is equipped with an adjustable handle for comfort and use of
operators of different heights. With a 9/16" wrench, simply adjust handle
at pivot points until desired operating position Is reached and then
retighten bolts.
INSTINST
INSTINST
INSTALLING OR CHANGING LPG FUELALLING OR CHANGING LPG FUEL
ALLING OR CHANGING LPG FUELALLING OR CHANGING LPG FUEL
ALLING OR CHANGING LPG FUEL
TT
TT
TANKANK
ANKANK
ANK
NOTE: For refueling tank, see “REFUELING AND STORING TANKS”.
1 Push machine In a designated safe area.
NOTE: Move to Step 6 for tank installation.
2 Close LPG tank valve on installed tank.
3 Operate engine until it stops from lack of fuel. (See Machine
Owners Operation)
FOR SAFETY: Never release or bleed tank Inside building or en-FOR SAFETY: Never release or bleed tank Inside building or en-
FOR SAFETY: Never release or bleed tank Inside building or en-FOR SAFETY: Never release or bleed tank Inside building or en-
FOR SAFETY: Never release or bleed tank Inside building or en-
closed areas.closed areas.
closed areas.closed areas.
closed areas.
FOR SAFETY: When servicing machine, keep flames and sparksFOR SAFETY: When servicing machine, keep flames and sparks
FOR SAFETY: When servicing machine, keep flames and sparksFOR SAFETY: When servicing machine, keep flames and sparks
FOR SAFETY: When servicing machine, keep flames and sparks
away from fuel system service area. Keep area well ventilated.away from fuel system service area. Keep area well ventilated.
away from fuel system service area. Keep area well ventilated.away from fuel system service area. Keep area well ventilated.
away from fuel system service area. Keep area well ventilated.
4 Put on gloves and remove service coupling by turning counter-
clockwise.
-
5 Unlatch and remove empty LPG fuel tank from machine and
store tank in a designated, safe area.
6 Carefully put full LPG tank on machine and position valve nozzle
towards engine.
NOTE: Make sure LPG fuel tank matches fuel system (Vapor System
Only).
CAUTION!CAUTION!
CAUTION!CAUTION!
CAUTION!
Never use a fuel tank not Intended for machine.
7 Fasten tank hold-down clamp to securely lock tank in position.
Adjustment to hold-down clamp can be made by threading latch
in or out.
8 Connect LPG fuel hose to valve nozzle by turning service cou-
pling clockwise (Tighten according to tank supplier recommen-
dations). Make sure service coupling Is clean and free of
damage. Also, make sure It matches machine service coupling.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
WhenInstallingtank, becarefulnottocross threadservice
coupling.
9 Open tank service valve slowly and check for leaks. Close
service valve immediately if a LPG leak Is detected.
INSTINST
INSTINST
INSTALLING OR REMOVING PALLING OR REMOVING P
ALLING OR REMOVING PALLING OR REMOVING P
ALLING OR REMOVING PAD DRIVERAD DRIVER
AD DRIVERAD DRIVER
AD DRIVER
AND PAND P
AND PAND P
AND PADSADS
ADSADS
ADS
Consult an authorized distributor to assist you in choosing the correct
pad for your specific cleaning need.
Pad Driver Installation:Pad Driver Installation:
Pad Driver Installation:Pad Driver Installation:
Pad Driver Installation:
1 Lean machine on left side (Dip stick tube down).
2 Place pad driver on drive shaft and spin pad driver clockwise to
install.
Pad Installation:Pad Installation:
Pad Installation:Pad Installation:
Pad Installation:
1 Tilt machine back on the rear caster (Park Position).
2 Remove plastic centerlock ring from pad driver. Center pad on
pad driver and secure with centerlock ring.
Pad Driver Removal :Pad Driver Removal :
Pad Driver Removal :Pad Driver Removal :
Pad Driver Removal :
1 With knee, apply downward pressure on bell of machine deck.
2 Place 3/4" (19 mm). Open end wrench onto top of drive shaft.
3 With rubber mallet, strike wrench to break loose shaft from pad
driver (counter-clockwise).
4 Lean machine on left side (Dip stick tube down).
5 Remove pad driver by spinning off counter-clockwise.
revised 03-7

66
66
6 - FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR
MACHINE OPERAMACHINE OPERA
MACHINE OPERAMACHINE OPERA
MACHINE OPERATIONTION
TIONTION
TION
FOR SAFETY: Do Not operate machine unless Operation Manual is read
and understood.
STST
STST
STARTING MACHINEARTING MACHINE
ARTING MACHINEARTING MACHINE
ARTING MACHINE
1 With machine on level surface. check oil level prior to starting
machine.
2 Tilt machine back onto rear caster (Park Position).
3 Remove any packing materials and obstructions from drive
system.
4 Turn LPG fuel knob ON tank. Check LPG gas level meter.
NOTE:NOTE:
NOTE:NOTE:
NOTE:Openingservice valve too quickly may cause service checkvalve
to stop flow of LPG fuel. If check valve stops fuel flow, close service
valve, wait a few seconds and open valve slowly again.
5 Push throttle lever to choke position for Honda engine only. All
other engines start in IDLE position.
6 Press start button OR turn key (if required) to engage starter. Do
not engage starter button for more than 20 seconds at a time. If
starter overheats it trips an internaI overload switch and will not
crank over. Wait at least 20 to 30 seconds between tries. When
engine starts, ease throttle back to running position. Do not hold
starter button in a continuous ON position, starter will burn out.
NOTE:NOTE:
NOTE:NOTE:
NOTE: For Electric Clutch model, see “OPERATING ELECTRIC CLUTCH”.
CAUTION!CAUTION!
CAUTION!CAUTION!
CAUTION!
Be careful not to allow the machine to come in contact with loose tiles
or other loose materials, remember the pad driver Is moving at very high
speed, and Injury can occur to the operator or passers by If pad driver
flings the loose material.
OPERAOPERA
OPERAOPERA
OPERATING ELECTRIC CLUTCH (OP-TING ELECTRIC CLUTCH (OP-
TING ELECTRIC CLUTCH (OP-TING ELECTRIC CLUTCH (OP-
TING ELECTRIC CLUTCH (OP-
TIONAL)TIONAL)
TIONAL)TIONAL)
TIONAL)
1 Once engine starts, move throttle control to SLOW rpm.
2 With throttle in SLOW, engage clutch by squeezing trigger
switch.
3 After clutch is engaged, move throttle to 3/4 throttle position and
then lower pad driver to floor.
CAUTION!CAUTION!
CAUTION!CAUTION!
CAUTION!
Never engage clutch In fast run position or with pad driver
on floor, this will cause damage to clutch.
STOPPING MACHINESTOPPING MACHINE
STOPPING MACHINESTOPPING MACHINE
STOPPING MACHINE
1 Turn LPG valve OFF at tank while running. This serves to purge
or bleed fuel hoses and carburetor system of fuel, so that there
isno dangerof gasescapingfrom lineswhen tank isremoved for
outside storage.
2 Tilt machine back on rear caster .
3 Engine will stop running when fuel lines bleed clear.
4 Pull throttle lever to STOP position after engine has stopped.
5 Turn key off if equipped.
EMERGENCY STOPPINGEMERGENCY STOPPING
EMERGENCY STOPPINGEMERGENCY STOPPING
EMERGENCY STOPPING
1 Pull throttle back to STOP OR turn off key if equipped.
2 Turn LPG valve OFF at tank.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Engine may back fire when stopped in this manner.
If machine is equipped with Kill Switch Option, activate switch.
WHILE OPERAWHILE OPERA
WHILE OPERAWHILE OPERA
WHILE OPERATING MACHINETING MACHINE
TING MACHINETING MACHINE
TING MACHINE
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
Exhaust contains poisonous carbon monoxide gas. Avoid
Inhalation of exhaust gases. Never operate machine in a
confined area without proper ventilation.
1 Refer to (SAFETY PRECAUTION: WHEN OPERATING MACHINE)
on page 4.
2 Do not run machine for more than 15 seconds in one spot or
damage will occur to the floor.
3 Do not leave unattended in idle position or with engine running
period. If machine needs to be idled for short periods, tilt
machine back and move throttle to idle. Machine should now
idle safely.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Do not Idle more than 5 minutes, longer periods will affect
oil flow and will cause damage to the engine.
4 For easier maneuverability, always start on right side of aisle.

FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR - 77
77
7
MAINTENANCEMAINTENANCE
MAINTENANCEMAINTENANCE
MAINTENANCE
WW
WW
WARNING!ARNING!
ARNING!ARNING!
ARNING!
Before attempting any maintenance procedures on ma-
chine, stop on level surface, shut off machine and turn off
LPG valve at tank.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Repairs and adjustments must be performed by authorized
and trained personnel.
To keep machine in good working condition, simply follow the daily,
weekly, and monthly maintenance procedures.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Always record maintenance and service.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Always keep machine free from dust and lint; the engine is
air cooled and for proper air flow to cool the engine, the
recoil filter must remain clean.
DAILY MAINTENANCE (Every 4 Hours of Operation)DAILY MAINTENANCE (Every 4 Hours of Operation)
DAILY MAINTENANCE (Every 4 Hours of Operation)DAILY MAINTENANCE (Every 4 Hours of Operation)
DAILY MAINTENANCE (Every 4 Hours of Operation)
1 Check oil level (Use 10W30 oil only).
2 Clean recoil filter .
3 Check belt tension by pinching belt together. Belt should only
depress 1/2" (13mm).
4 Clean all air filters by blowing out dust and dirt and/or washing
the foam filters (recoil and carburetor pre- filter) with warm,
sudsy water and rinsing clean.
(Be careful not to wet the paper
carburetor filters.) Be sure filters are clean and dry before use.
Do not oil foam or filter .
5 Make sure all components are secure and tight.
6 Check pad daily (clean or replace).
7 Clean machine.
8 For Dust Control models, clean dust collection bag.
WEEKLY MAINTENANCE (Every 20 Hours of Operation)WEEKLY MAINTENANCE (Every 20 Hours of Operation)
WEEKLY MAINTENANCE (Every 20 Hours of Operation)WEEKLY MAINTENANCE (Every 20 Hours of Operation)
WEEKLY MAINTENANCE (Every 20 Hours of Operation)
1 Checkoil level. Changeoiland filters at50 hours ofoperation.Use
10W30 Motor Oil or other no ash motor oils designed for use in
propane engines. Use of non-recommended oil may void the
engine warranty.
See Engine Owners Manual for complete servicing details
2 Inspect carburetor air filter by removing wing nut and over on top
of carburetor. Replace if dry or deposits are present.
3 Check belt for tension. Tighten if loose. If worn, replace with
proper belt.
(See “ADJUSTING BELT TENSION”). Refer to parts
schematic for size of belt required.
4 Inspect and tighten nuts and bolts on engine and frame.
5 Examine all propane hoses and connections for leaks or wear.
Replace if necessary.
6 Grease wheels. Use white lithium grease only and use no more
than 1 pump of grease. More grease than recommended will
push seal and dust cover out, allowing dust and other foreign
materials into the bearings, shortening the life of the wheel
significantly.
MONTHLY MAINTENANCE (Every 80 hours of Operation)MONTHLY MAINTENANCE (Every 80 hours of Operation)
MONTHLY MAINTENANCE (Every 80 hours of Operation)MONTHLY MAINTENANCE (Every 80 hours of Operation)
MONTHLY MAINTENANCE (Every 80 hours of Operation)
1 Perform all daily and weekly services.
2 Torque the head bolts when engine is cold in a crisscross
pattern as per engine manufacturers specifications
(See En-
gine Owners Manual).
3 Checkvalve clearance with cold engineas per engine manufac-
turers specifications (See Engine Owners Manual).
4 Torque valve cover as per engine manufacturers specifications
(See Engine Owners Manual).
5 Inspect spark plug. Replace if necessary.
6 Change oil and oil filter.
7 Inspect fuel hoses for leak (repair as needed).
8 Wash undercarriage of machine to remove all dust and debris.
9 To ensure proper ventilation, remove engine cover and clean
engine.
10 Replace air filter element and foam filter.
QUARTERLY MAINTENANCE (Every 250 Hours of Operation)QUARTERLY MAINTENANCE (Every 250 Hours of Operation)
QUARTERLY MAINTENANCE (Every 250 Hours of Operation)QUARTERLY MAINTENANCE (Every 250 Hours of Operation)
QUARTERLY MAINTENANCE (Every 250 Hours of Operation)
1 Perform all of the above maintenance procedures and have
engine checked by an Authorized Service Center.
2 Check air gap in electronic ignition coil.
3 Check valves with engine cold.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Consult Engine Manual for complete servicing and adjustments
information.
LIFE OF MACHINELIFE OF MACHINE
LIFE OF MACHINELIFE OF MACHINE
LIFE OF MACHINE
1 Change oil regularly.
2 Clean recoil filter regularly.
3 Clean carburetor filter regularly.
4 Keep machine clean from dust and debris.
FUELSYSTEMFUELSYSTEM
FUELSYSTEMFUELSYSTEM
FUELSYSTEM
Adjustmentsfortheair/fuelmixturemustbemadeonlybyanAuthorized
Service Center. Improper adjustments can cause high levels of carbon
monoxide emissions which may cause carbon monoxide poisoning or
it can lead to engine damage.
• Idle speed is adjusting by turning adjustment screw on regula-
tor.
• Fuel flow is adjusted by adjustment screw on carburetor spud-
in.
CHANGING THE OILCHANGING THE OIL
CHANGING THE OILCHANGING THE OIL
CHANGING THE OIL
The manufacturer recommendations 10W30 oil.
1 Run engine for five minutes to warm oil.
2 Make sure machine is on level surface. Locate oil drain plug on
rear of engine beside oil cap and remove by turning counter-
clockwise with wrench.
3 Allow oil to run into pan under machine. Allow to completely
drain.
4 Install drain plug and tighten drain plug by turning clockwise
with wrench.
5 Slowly add one quart (946.3 mi) of 10W30 Motor Oil. Then check
oil level with dip stick in oil fill cap. Add additional oil if neces-
sary.
6 Replace oil-fill cap assembly. Hand tighten only.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Do not overfill and never run engine low on oil.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
When checking oil, be sure cap is fully screwed out and
free.Donotcheckoilbyscrewingcapinandthenoutagain,
this will give you a false reading.

88
88
8 - FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR
ADJUSTING BELT TENSIONADJUSTING BELT TENSION
ADJUSTING BELT TENSIONADJUSTING BELT TENSION
ADJUSTING BELT TENSION
Tools required:
• 3/4" (19mm) open end wrench
• 15/16" (24mm) deep-well socket.
1 Loosen Mounting Bolt on top side of machine while applying
counter-pressure to Adjusting Nut on underside of deck.
NOTE:NOTE:
NOTE:NOTE:
NOTE: The mounting bolt muse be loosened first.
2 Rotate Adjusting Nut counterclockwise with socket to apply
tension to belt.
3 While holding the tension on the Adjusting Nut. Tighten Mount-
ing Bolt.
4 Check belt tension by pinching belt together. Belt should only
depress 1/2" (12mm).
REFUELING AND STORING TREFUELING AND STORING T
REFUELING AND STORING TREFUELING AND STORING T
REFUELING AND STORING TANKSANKS
ANKSANKS
ANKS
The following information refers to United States regulations on pro-
pane. For outside the United States, owner, must assure that required
regulations are met.
The manufacturer would like to acknowledge NFPA 58, Standard for
Storage and Handling of Liquefied Petroleum Gases, 1993 Edition. This
publication is available through the National Fire Protection Associa-
tion (NFPA) in Quincy, Massachusetts (1-800-344-3555). The NFPA was
established to set guidelines for, among other things, the use of pro-
pane.
Propane is a flammable gas whose vapors are heavier than air. It can
explode under certain conditions. It is not different than other items
commonly used today which must be operated in a safe way such as
automobiles, gas stoves, airplanes, etc. Propane is odorized with an
agent with a distinct odor that is recognizable at very low concentra-
tions. This helps in identifying leaks even when they are small.
Awareness and basic safely precautions are required. As long as these
precautions are followed, risk is negligible. Ignorance, however, could
pose needless risk. Therein lies the reason behind NFPA 58 and the
Safety Publication.
NFPA58categorizespropane-poweredbufferswithforklift trucks, (see
section 3-6.4.4). In essence, the only difference between the two lies in
the ability of the buffer with its 20-pound tank to be stored in concealed
areas (like janitor closets, etc.).
If a machine and its tank of propane were stored in a closet and afire
occurred, the propane in the tank could be a threat to fire fighters due
to the potential for a B.L.E.V.E. (Boiling Liquid Expanding Vapor Explo-
sion). Exposure of the tank to heat can also cause the relief valve to
open thereby releasing flammable vapors that can cause the fire to
intensify when ignited.
The NFPA Technical Committee prohibits the storage of such contain-
ers in buildings.

FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR - 99
99
9
REFUELING LP GAS TREFUELING LP GAS T
REFUELING LP GAS TREFUELING LP GAS T
REFUELING LP GAS TANKSANKS
ANKSANKS
ANKS
NOTE:NOTE:
NOTE:NOTE:
NOTE: See ‘INSTALLING OR CHANGING LPG FUEL TANK” for Tank
Removal.
TheLPgas tanksuppliedwithmachinehas a20Ib. (9.3kg),5-gallon(18.9L)
capacity. DO NOT OVERFILL.DO NOT OVERFILL.
DO NOT OVERFILL.DO NOT OVERFILL.
DO NOT OVERFILL. Overfilling will cause the regulator to
freeze up. Use only D.O.T. and U.L. Listed propane tank and only fill tank
at a reputable propane dealer .
DO NOT attempt to repair the propane tank yourself. Return tank to
dealer for repair.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Never use a tank not intended for the propane machine. Do not
substitute tanks from barbecue grills, etc.
The manufacturer exclusively uses aluminum and steel cylinders that
meet the Department of Transportation guidelines contained in the
D.O.T. # 4ET240 and are additionally U.L. listed.
NFPA 58 discusses the major concerns for filling tanks properly in
Chapter 4. In summary, the tank should never be completely filled with
liquid. A tank that is completely full could create a hazard. The hazard is
known as a hydrostatic pressure situation.
To illustrate this situation, suppose the temperature outside is very cold
(perhaps well below freezing). You fill your tank outside and then bring
it inside where the temperature is maybe 60 degrees Fahrenheit or
warmer. An increase in air temperature will drive up the cylinder
pressure placing stress on the tank. Before reaching a critical pressure
point, the relief valve should open, relieving the pressure by venting
vapor at the top of the tank. However, if there is no vapor at the top of the
tank, this safety measure is compromised. Overfilled tanks do not allow
this built-in safety feature to function properly.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Overfilling a tank usually results in liquid flowing through
the hose and down into the regulator. This can result in
damage to the machine.
If you observe frost on the regulator, someone has overfilled the tank.
Take the tank to a safe outside location and vent the excess propane.
Venting is accomplished by:
1 Removing the tank from machine.
2 Taking tank outside of building to safe area.
3 Opening the small relief valve located on top of machine.
4 Keep tank upright.
5 Allow to vent until fuel vapor is not visible.
Whether the tank is filled by weight (most accurate) or by volume, using
a gage, make sure the person doing the filling is qualified.
CAUTION!CAUTION!
CAUTION!CAUTION!
CAUTION!
Avoid overfilling tanks. Only fill to 80% of capacity. The
manufacturerrecommendsthatrefuelingbeaccomplished
by qualified personnel away from public buildings outside.
We further recommend that additional tanks be used so
that rather than refueling at the job site, a simple exchange
of tanks occurs.
STORING LP GAS TSTORING LP GAS T
STORING LP GAS TSTORING LP GAS T
STORING LP GAS TANKSANKS
ANKSANKS
ANKS
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Tanks (20Ib.) should not be stored in buildings used by the
publicorfrequentedbyanyonepassingthroughorworking
in the building. Inside storage in buildings designated as
shop or machinery facilities are acceptable.
Section 5-2.1.1 of the NFPA 58 says: “Containers in storage shall be so
located as to minimize exposure to excessive temperature rise, physi-
cal damage or tampering.”
Provision must be made for venting the actual storage area with both
floorlevelandhighlevelopenings. This venting assures that the heavier
than air propane gas will not settle in pockets, but disperse.
If storage is in a shop or machine storage area that is connected or a
part of an office complex, it should be separated by afire wall along with
proper venting to the outside.
Since these requirements can seldom be found, outside open air
storage is the most practical alternative.
When this option is used, the storage container may be located with
“zero”clearance fromthebuilding and withat least 5'of space between
the cage and the nearest building opening.
The tank must be in a secure, tamper-proof security storage enclosure
that provides safety from accident or vandalism.
CAUTION!CAUTION!
CAUTION!CAUTION!
CAUTION!
Tanks must always be stored in the upright position. The
uprightpositionassuresthat the discharge is largely vapor
rather than liquid. This is important from the standpoint of
both the quantity of the potential flammable vapor/air mix-
ture and the relieving capacity for the pressure relief de-
vice. (The escape of vapor presents much less hazard than
the escape of liquid).
The manufacturer recommends that tanks be removed from the ma-
chine after use and stored accordingly. The machine can then be
placed in a secure area inside, away from the tank.
NOTE:NOTE:
NOTE:NOTE:
NOTE: Local jurisdiction always prevails there may. Be varying require-
ments. Always check with the local authorities.

1010
1010
10 - FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR
STORING MACHINESTORING MACHINE
STORING MACHINESTORING MACHINE
STORING MACHINE
1 Remove LPG tank from machine when not in use.
FOR SAFETY: Never release or bleed tank inside building or inFOR SAFETY: Never release or bleed tank inside building or in
FOR SAFETY: Never release or bleed tank inside building or inFOR SAFETY: Never release or bleed tank inside building or in
FOR SAFETY: Never release or bleed tank inside building or in
enclosed areas.enclosed areas.
enclosed areas.enclosed areas.
enclosed areas.
NOTE:NOTE:
NOTE:NOTE:
NOTE: See “INSTALLING OR CHANGING LPG FUEL TANK” for Tank
Removal.
2 Perform all Daily Maintenance procedures.
3 Change engine oil.
4 Store machine in cool, dry area, away from fuel tanks. Tilt
machine back onto rear caster (Park Position).
5 Store tanks in an approved area.
NOTE:NOTE:
NOTE:NOTE:
NOTE: See “STORING LP GAS TANKS”.
TRANSPORTING MACHINETRANSPORTING MACHINE
TRANSPORTING MACHINETRANSPORTING MACHINE
TRANSPORTING MACHINE
For ease of transportation, the machines handle can be folded over the
engine. The tank can be transported on machine provided that tank hold-
down clamp is securely fastened around tank and tank valve is turned
completely OFF.
AA
AA
ATTENTION!TTENTION!
TTENTION!TTENTION!
TTENTION!
Never transport a machine in an enclosed area that has not
had sufficient time to cool down.

FORM NO. 56041536 - SelectGloss™21PH, 21PK, 27PK, 27PO, 27PR - 1111
1111
11
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE
TROUBLE SHOOTING GUIDE
PROBLEMPROBLEM
PROBLEMPROBLEM
PROBLEM CAUSECAUSE
CAUSECAUSE
CAUSE SOLUTIONSOLUTION
SOLUTIONSOLUTION
SOLUTION
Will not start. No fuel or dirt in fuel line. See Engine Owners Manual for servicing.
Blown head gasket.
Engine overload.
Dirty air cleaner.
Faulty spark plug.
Fuel system out of adjustment.
Defective ignition coil.
Hard to start. Improper fuel, no fuel or dirt in fuel line. See Engine Owners Manual for servicing.
Engine overload.
Dirty air cleaner .
Faulty spark plug.
Spark plug or head bolts loose.
Blown head gasket.
Timing, coil, or valve needs adjusting.
Carburetor needs adjusting.
Regulator needs adjusting.
Insufficient vacuum.
Lacks power . Improper valve clearance. See Engine Owners Manual for servicing.
Improper fuel or dirt in line.
Faulty spark plug.
Improper oil level.
Valve seats need adjusting.
Leaking head gasket.
Governor needs adjusting.
Worn rings.
Smell of burned rubber. Belt out of adjustment. See “ADJUSTING BELT TENSION”.
Engine overheats. Dirt in fuel line.
Incorrect oil level.
Engine overload.
High fuel consumption. Dirty air filters. See Engine Owners Manual for servicing.
Dirty air cleaners.
Machine stops suddenly. Faulty spark plug. See Engine Owners Manual for servicing.
Pad not centered on pad driver .
Incorrect pad size for pad driver.
Oil shut down sensor activated. Add recommended oil.
Excess vibration. Bolts loose on engine or deck of unit. See Engine Owners Manual for servicing.
No fuel or dirt in fuel line.
Incorrect oil level.
Engine overload.
Dirty air filters.
Faulty spark plug.

1212
1212
12
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
SELECTGLOSSSELECTGLOSS
SELECTGLOSSSELECTGLOSS
SELECTGLOSS
™™
™™
™
21PH / 21PK21PH / 21PK
21PH / 21PK21PH / 21PK
21PH / 21PK

1313
1313
13
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
SELECTGLOSSSELECTGLOSS
SELECTGLOSSSELECTGLOSS
SELECTGLOSS
™™
™™
™
21PH / 21PK21PH / 21PK
21PH / 21PK21PH / 21PK
21PH / 21PK
ItemItem
ItemItem
Item Ref. No.Ref. No.
Ref. No.Ref. No.
Ref. No. QtyQty
QtyQty
Qty DescriptionDescription
DescriptionDescription
Description
1 56649812 2 Foam Hand Grip
2 56649816 1 FM Handle
3 56649726 1 Clutch Switch Mounting Plate
4 56102526 1 Key Switch
* 56102583 1 Replacement Key
5 56102527 1 Key Switch Holder
6 56649817 1 Battery Box
* 56649818 1 Key Switch Bracket
* 56649819 1 Choke Bracket (Kawasaki)
7 56102507 1 Kawasaki 17HP
56102532 1 Honda 390 13HP
8 56102508 1 Pulley, 3.5 x 1
9 56102523 1 Battery Connector Complete (Kawasaki)
10 56102522 1 Battery, 12V
11 56102521 1 Hour Meter
12 56649820 1 Deck, 21” Aluminum
13 56649821 1 Bumper Molding
14 56015141 2 Decal, Kent SelectGloss 21PH
56015144 2 Decal, Kent SelectGloss 21PK
15 56102509 1 Front Bearing Assy
16 56102533 1 Pulley, 6.2
17 56649822 1 Belt, B x 40
18 56102513 1 Centerlock
19 56649823 2 Wheel W/Bracket, 6 x 5
56649824 2 Wheel, 6 x 1.5
20 56102535 1 21” Flex Pad Driver
21 56102518 1 Caster, 3”
22 56102517 1 Flange
23 56102519 1 Idler Pulley
24 56102520 1 Tensioner Arm
25 56102524 1 Steel LP Tank
26 56649825 2 Velcro Tape
27 56102529 1 Throttle Cable
28 56102598 1 21” Flex Pad Driver Complete
** 56102618 1 21” Pad Driver Complete
* 56102538 1 Choke Cable (Kawasaki)
* 56102539 1 Honda Starter
** 56388355 1 21” Beige Pads (case of 5)
** 56102615 1 Honda GXV390 Engine Service Kit
** 56102617 1 Kawasaki 17hp Engine Service Kit
** 56102658 A/R Two Tank Cage
* = Not Shown
** = Optional
NOTE:NOTE:
NOTE:NOTE:
NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.
04-5

1414
1414
14
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
SELECTGLOSSSELECTGLOSS
SELECTGLOSSSELECTGLOSS
SELECTGLOSS
™™
™™
™
27PK / 27PO27PK / 27PO
27PK / 27PO27PK / 27PO
27PK / 27PO

1515
1515
15
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
ItemItem
ItemItem
Item Ref. No.Ref. No.
Ref. No.Ref. No.
Ref. No. QtyQty
QtyQty
Qty DescriptionDescription
DescriptionDescription
Description
1 56649812 2 Foam Hand Grip
2 56649816 1 FM Handle
3 56649726 Clutch Switch Mounting Plate
4 56102526 1 Key Switch
* 56102583 1 Replacement Key
5 56102527 1 Key Switch Holder
6 56649817 1 Battery Box
* 56649818 1 Key Switch Bracket
* 56649819 1 Choke Bracket (Kawasaki)
7 56102507 1 Kawasaki 17HP
56102541 1 Onan 20HP
8 56102508 1 Pulley, 3.5 x 1
9 56102523 1 Battery Connector Complete (Kawasaki)
56102542 1 Battery Connector (Onan)
10 56102522 1 Battery, 12V
11 56102521 1 Hour Meter
12 56649826 1 Deck, 27” Aluminum
13 56649821 1 Bumper Molding
14 56015148 2 Decal, Kent SelectGloss 27PK
56015152 2 Decal, Kent SelectGloss 27PO
15 56102509 1 Front Bearing Assy
16 56102510 1 Pulley, 8.5 x 1
17 56102512 1 Belt, B x 50
18 56102513 1 Centerlock
19 56649823 2 Wheel W/Bracket, 6 x 5
56649824 2 Wheel, 6 x 1.5
20 56102514 1 27” Flex Pad Driver
21 56649827 1 Caster
22 56102517 1 Flange
23 56102519 1 Idler Pulley
24 56102520 1 Tensioner Arm
25 56102524 1 Steel LP Tank
26 56649825 2 Velcro Tape
27 56102529 1 Throttle Cable
28 56102516 1 27” Flex Pad Driver Complete
** 56102619 1 27” Pad Driver Complete
* 56102538 1 Choke Cable (Kawasaki)
* 56102543 1 Regulator Bracket (Onan)
** 56420163 1 27” Beige Pads (case of 5)
** 56102616 1 Onan 20 P248 Engine Service Kit
** 56102617 1 Kawasaki 17hp Engine Service Kit
** 56102658 A/R Two Tank Cage
* = Not Shown
** = Optional
NOTE:NOTE:
NOTE:NOTE:
NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.
SELECTGLOSSSELECTGLOSS
SELECTGLOSSSELECTGLOSS
SELECTGLOSS
™™
™™
™
27PK / 27PO27PK / 27PO
27PK / 27PO27PK / 27PO
27PK / 27PO
04-5

1616
1616
16
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
SELECTGLOSSSELECTGLOSS
SELECTGLOSSSELECTGLOSS
SELECTGLOSS
™™
™™
™
27PR27PR
27PR27PR
27PR
1
FRONT
27 22
26
17
31
30
23
29
24
19
28
25
21
20
2
16 18
13
14
15
9
10
11
12
7
8
5
6
4
3
32
03-7

1717
1717
17
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
SELECTGLOSSSELECTGLOSS
SELECTGLOSSSELECTGLOSS
SELECTGLOSS
™™
™™
™
27PR27PR
27PR27PR
27PR
ItemItem
ItemItem
Item Ref. No.Ref. No.
Ref. No.Ref. No.
Ref. No. QtyQty
QtyQty
Qty DescriptionDescription
DescriptionDescription
Description
1 56102645 1 Robin ZXV 653 Engine
2 56649826 1 Deck 27” Aluminum
3 56102509 1 Front Bearing Assy Complete
4 56102648 1 Pulley, 7.0 x 1.0
5 56102508 1 Pulley, 3.5 x 1.0
6 56102649 1 Belt, B x 48
7 56102520 1 Belt Tensioner
8 56102519 1 Idler pulley
9 56102517 1 Flange
10 56102514 1 27” Flex Pad Driver
11 56102513 1 Center lock
12 56420163 A/R 27” Beige Pads (case of 5)
13 56649827 2 2” Caster W/Gray Wheel
14 56102651 2 Bracket Wheel 5”
15 56649824 2 Wheel, 6” x 1.5” W/Axle
* 56649823 2 Wheel W/Bracket (14 & 15)(14 & 15)
(14 & 15)(14 & 15)
(14 & 15)
16 56102521 1 Hour Meter
17 56649816 1 FM Handle
18 56102528 1 Toggle
19 56102524 1 Tank, LP Steel W/OPD
20 56102529 1 Throttle Cable
21 56649812 2 Hand Grip
22 56649817 1 Battery Box
23 56102650 1 Battery Connector Complete
24 56102527 1 Key Switch Housing
25 56102526 1 Key Switch
* 56102583 1 Replacement Key
26 56102522 1 Battery, 12V
27 56102538 1 Choke Cable
28 56649818 1 Key Switch Bracket
29 56649819 1 Choke Bracket
30 56649726 1 Clutch Switch Mounting Plate
31 56102575 1 Clutch Switch Assy Complete
32 56015207 2 Decal, Kent SelectGloss 27
** 56102646 1 Robin 22hp Engine Service Kit
** 56102658 A/R Two Tank Cage
* = Not Shown
** = Optional
NOTE:NOTE:
NOTE:NOTE:
NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.
04-5

1818
1818
18
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE
ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE
ROBIN ZXV 653 ENGINE
4
FRONT
3
5
8
7
2
1
6
10
11
14
12
15
13
9
03-7

1919
1919
19
FORM NO. 56041536
SelectGlossSelectGloss
SelectGlossSelectGloss
SelectGloss
™™
™™
™
02-10
ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE
ROBIN ZXV 653 ENGINEROBIN ZXV 653 ENGINE
ROBIN ZXV 653 ENGINE
ItemItem
ItemItem
Item Ref. No.Ref. No.
Ref. No.Ref. No.
Ref. No. QtyQty
QtyQty
Qty DescriptionDescription
DescriptionDescription
Description
1 56102565 1 Recoil Filter Support gasket
2 56102632 1 Engine Cover
3 56102633 1 Filter Support Screen
4 56102634 1 Recoil Filter
5 56102563 1 Oil Pressure Switch
6 56102635 1 Oil Drain Valve
7 56102506 1 Automatic Shut Down system
8 56102637 2 Scr, Pan Phil 6-32 x .62
9 56102638 2 Nut, Jack 6-32
10 56102639 2 Exhaust Manifold Gasket
11 56102640 1 Exhaust Manifold
12 56102641 1 Muffler Clamp
13 56102642 1 Muffler, Catalytic
14 56102643 1 Oxygen Sensor
15 56102645 1 Robin ZXV 653 Engine
** 56102646 1 Robin 22hp Engine Service Kit
** = Optional
NOTE:NOTE:
NOTE:NOTE:
NOTE: For engine information not listed in the Standard Parts List, refer to the appropriate Engine Parts Manual.
03-7