Kenway 59661 Assembly instructions

Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
RED: 59654
AMBER: 59661
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference. 22i
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright©2022 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may not be included.
Read this material before using this
product. Failure to do so can result in
serious injury. SAVE THIS MANUAL.

Page 2 For technical questions, please call 1-888-866-5797. 59661 59654
Specifications
Mount Dimensions 4″ L x 1-1/2" W x 1-1/4" H
Mounting Holes 3/16" diameter and 3" apart at centers
Light Diameter 3/4"
Light Wattage 0.8W
Light Current Draw 0.07A
Electrical Requirements 12VDC
Important Safety Information
Assembly Precautions
1. Assemble only according to these
instructions. Improper assembly
can create hazards.
2. Wear ANSI-approved safety goggles and
heavy-duty work gloves during assembly.
3. Keep assembly area clean and well lit.
4. Keep bystanders out of the
area during assembly.
5. Do not assemble when tired
or when under the influence of
alcohol, drugs or medication.
6. Replacement parts and accessories.
When servicing, use only identical
replacement parts. Use of any other
parts will void the warranty.
7. Always check hardware and assembled
parts after assembling. All connections
should be tight and hardware tightened.
8. Weight capacity and other product
capabilities apply to properly and
completely assembled product only.
Use Precautions
1. This product is not a toy. Do not allow
children to play with or near this item.
2. Use as intended only.
3. Inspect before every use; do not use
if parts are loose or damaged.
4. Use the right product for the job.
There are certain applications for
which the Lamp was designed.
5. Make certain to follow all local DMV
(Department of Motor Vehicles)
laws regarding vehicles and
vehicle lighting requirements.
6. Do not cut or rewire any
part of the Lamp.
7. Make certain the vehicle is turned
off before doing any maintenance.
8. The warnings, cautions, and instructions
discussed in this instruction manual
cannot cover all possible conditions
and situations that may occur. It must
be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
9. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.

Page 3For technical questions, please call 1-888-866-5797.59661 59654
Installation Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this document including all text under subheadings therein
before set up or use of this product.
If you do not have experience doing this
type of electrical work, the job should be
done by an automotive service technician.
NOTICE: Placement of the lights must
comply with FMVSS/CMVSS 108 Federal
Lighting Regulations for Trailers.
WARNING! TO PREVENT SERIOUS
INJURY: Turn off vehicle engine and
disconnect the power supply (battery) before
doing any maintenance or installation.
1. With the light removed from center
of the mount, place the mount on the
location for the Marker Light. Use it as a
template to mark the two side mounting
holes and center hole for the wires.
2. Insert the light back into the
center of the mount.
3. On the vehicle, feed the Marker Light
wires through the hole drilled
for the center opening.
4. Use a pin connector or in-line splice
connector (both sold separately) to
connect the light to your vehicle.
5. When using an in-line splice connector,
it is not necessary to strip the wires.
a. Insert the wire from your
vehicle into one channel of
the in-line splice connector.
b. Insert the wire extending from
the Light into the second channel
of the in-line splice connector.
c. Fold down the tab on the
in-line splice connector to
make the connection.
6. Connect the white wire
NEGATIVE (-) to ground.
7. When connecting the Marker Light to
a trailer, both the amber and red light’s
black wire are connected to the trailer’s
tail light wire (normally the brown wire
on a trailer wired to standard).
8. Once the wires are properly
connected, reconnect the power supply
(battery) and test the Marker Light
before mounting it in place.
9. Turn off ignition/battery.
10.Use two #8 Self Drilling Screws
(sold separately) to attach the
Marker Light to the vehicle surface.
11. Make certain the Marker Light is well
seated and the ground wire makes
proper contact with a metal surface.

Record Serial Number Here:
Note: If product has no serial number, record
month and year of purchase instead.
Note: Replacement parts are
not available for this item.
Specify UPC number:
Amber: 193175478023
Red: 193175477958
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality
and durability standards, and warrants to the original purchaser that this product is free from
defects in materials and workmanship for the period of 90 days from the date of purchase.
This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence
or accidents, repairs or alterations outside our facilities, criminal activity, improper installation,
normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,
injuries to persons or property, or for incidental, contingent, special or consequential damages
arising from the use of our product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies the
defect, we will either repair or replace the product at our election or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a
replacement. We will return repaired products at our expense, but if we determine
there is no defect, or that the defect resulted from causes not within the scope
of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
26677 Agoura Road • Calabasas, CA 91302 • 1-888-866-5797