Kenwood KMM-100U User manual

KMM-100
KMM-100U
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE
MODE D’EMPLOI
RECEPTOR DE MEDIOS DIGITALES
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from
your new Digital Media Receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for
information or service on the product.
Model
KMM-100/ KMM-100U Serial number
US Residents Only
Register Online
Register your Kenwood product at www.Kenwoodusa.com
GET0867-001A (KN)© 2013 JVC KENWOOD Corporation
EN_KMM-100[KN]3.indd 1EN_KMM-100[KN]3.indd 1 11/21/12 8:50:26 AM11/21/12 8:50:26 AM

2
CONTENTS
BEFORE USE
Warning
Do not operate any function that takes your
attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear
sounds outside the car to prevent accident.
• Lower the volume before playing digital
sources to avoid damaging the speakers by
the sudden increase of the output level.
General:
• Avoid using the USB device or iPod/iPhone if
it might hinder driving safety.
• Make sure all important data has been backed
up. We shall bear no responsibility for any loss
of recorded data.
• Never put or leave any metallic objects (such
as coins or metal tools) inside the unit, to
prevent a short circuit.
Remote control (RC-406):
• Do not leave the remote control in hot places
such as on the dashboard.
• The Lithium battery is in danger of explosion
if replaced incorrectly. Replace it only with the
same or equivalent type.
• The battery pack or batteries shall not be
exposed to excessive heat such as sunshine,
fire or the like.
• Keep battery out of reach of children and in
original package until ready to use. Dispose of
used batteries promptly. If swallowed, contact
a physician immediately.
CALIFORNIA, USA ONLY
This perchlorate WARNING applies only to the
product sold or distributed in California USA
“Perchlorate Material–special handling may
apply, See www.dtsc.ca.gov/hazardouswaste/
perchlorate.”
How to read this manual
• Operations explained mainly using
buttons on the faceplate.
•
[XX] indicates the selected items.
• ( ➜ XX) indicates references are available
on the stated page number.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
RADIO 5
USB / iPod 7
Pandora® (for
KMM-100U
)9
AUX 10
DISPLAY SETTINGS 10
AUDIO SETTINGS 11
MORE INFORMATION 12
TROUBLESHOOTING 13
INSTALLATION / CONNECTION 14
SPECIFICATIONS 17
EN_KMM-100[KN]2.indd 2EN_KMM-100[KN]2.indd 2 11/5/12 5:32:37 PM11/5/12 5:32:37 PM

3
ENGLISH |
KMM-100U
BASICS
To Do this (on the faceplate) Do this (on the remote control)
Turn on the power Press LSRC.
• Press and hold to turn off the
power.
Press and hold SRC to turn off the
power.
( Pressing SRC does not turn on
the power. )
Adjust the volume Turn the volume knob. Press VOL or VOL .
Press ATT during playback to
attenuate the sound.
• Press again to cancel.
Select a source Press LSRC repeatedly. Press SRC repeatedly.
Change the display
information*
Press SCRL DISP repeatedly.
• Press and hold to scroll the
current display information.
( not available )
*
KMM-100
: You can also select to turn off the display information by pressing SCRL DISP
repeatedly.
Pull out the insulation sheet
when using for the first time.
How to replace the battery
* Not used.
Remote sensor (Do not
expose to bright sunlight.)
Volume knob
(turn/press)
Display window
Detach button
How to resetAttach Detach
Your preset adjustments
will also be erased.
EN_KMM-100[KN]2.indd 3EN_KMM-100[KN]2.indd 3 11/5/12 5:32:37 PM11/5/12 5:32:37 PM

4
GETTING STARTED
Cancel the demonstration
When you turn on the power (or after you reset the unit), the display shows:
“CANCEL DEMO” \“PRESS” \“VOLUME KNOB”
1 Press the volume knob.
[YES] is selected for the initial setup.
2 Press the volume knob again.
“DEMO OFF” appears.
Set the clock
1 Press the volume knob to enter [FUNCTION] .
2 Turn the volume knob to select [SETTINGS] , then press the knob.
3 Turn the volume knob to select [CLOCK] , then press the knob.
4 Turn the volume knob to select [CLOCK ADJ] , then press the knob.
5 Turn the volume knob to adjust the hour, then press the knob.
6 Turn the volume knob to adjust the minute, then press the knob.
Press 4 / ¢to move between the hour and minute adjustment.
7 Press and hold to exit.
(or)
Press and hold SCRL DISP to enter clock adjustment mode directly while in clock
display screen.
Then, perform steps 5and 6above to set the clock.
Set the initial settings
1 Press SRC to enter [STANDBY] .
2 Press the volume knob to enter [FUNCTION] .
3 Turn the volume knob to select [INITIAL SET] , then press the knob.
4 Turn the volume knob to make a selection (see the following table), then press the
knob.
5 Press and hold to exit.
• To return to the previous hierarchy, press .
3
1
2
EN_KMM-100[KN]2.indd 4EN_KMM-100[KN]2.indd 4 11/5/12 5:32:38 PM11/5/12 5:32:38 PM

5
ENGLISH |
GETTING STARTED
Default: XX
PRESET TYPE NORM: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ;
MIX: Memorizes one station for each preset button regardless of the selected band.
KEY BEEP ON: Activates the keypress tone. ; OFF: Deactivates.
PANDORA SRC
KMM-100U
:
ON: Enables PANDORA in source selection. ; OFF: Disables. (
➜ 9)
BUILTIN AUX ON: Enables AUX in source selection. ; OFF: Disables. (
➜ 10)
SWITCH PRE REAR/ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out
terminals on the rear (through an external amplifier).
SP SELECT OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches or 4 inches, 6×9 inches
or 6 inches) or OEM speakers for optimum performance.
F/W UPDATE
F/W UP xx.xx YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated).
For details on how to update the firmware, see: www.kenwood.com/cs/ce/
RADIO
Search for a station
1 Press LSRC to select TUNER.
2 Press repeatedly (or press *AM– / #FM+ on RC-406) to select FM1/ FM2/ FM3/ AM.
3 Press 4/¢(or press 4/ ¢(+) on RC-406) to search for a station.
• To store a station: Press and hold one of the number buttons (1to 6).
• To select a stored station: Press one of the number buttons (1to 6) (or press one of the
number buttons (1to 6) on RC-406).
Direct Access Tuning (using RC-406)
1 Press *AM– / #FM+ to select a band.
2 Press DIRECT to enter Direct Access Tuning.
“– – – • –” (for FM) or “– – – –” (for AM) appears on the display.
3 Press the number buttons to enter a frequency.
4 Press ENT 38 to search for a frequency.
• To cancel, press .
• If no operation is done for 10 seconds after step 3, Direct Access Tuning is automatically canceled.
EN_KMM-100[KN]3.indd 5EN_KMM-100[KN]3.indd 5 11/21/12 8:50:29 AM11/21/12 8:50:29 AM