Kenwood SRC-501 User manual

STEREO SYSTEM RACK
SRC-501
ASSEMBLY INSTRUCTIONS
KENWOOD
KENWOOD CORPORATION
©PRINTED IN U.S.A, B61-0416-00(K)(TCA)
RO213
IMPORTANT:
—————-—
=
ore
:
Notes
on
Assembling
*
Before
operating
your
new
KENWOOD
product,
read
through
this
assem-
¢
During
assembling,
be
sure
to
verify
the
numbers
stamped
on
the
boards.
bly
manual
carefully
to
get
the
most
out
of
it.
*
Mount
the
rear
panel
after
assembling
the
side
panel
on
the
bottom
shelf
*
Save
this
assembly
instructions.
7
:
at
aright
angle.
:
;
:
oo
?
ee
‘e
*
When
mounting
the
top
shelf
and
kick
plate
on
the
side
panel,
use
glue
Before
Assembling
for
adhesive.
Be
sure
to
remove
any
excess
glue
before
it
dries.
* If the amplifier wobbles when its key switches are pressed, insert a wooden
*
Be
sure
to
check
that
all
parts
are
accounted
for
before
di
i
f
th
:
:
seca
BEETS
nae
Se
aie
ee
dowel
into
the
hole
on
the
side
panel
and
fix
the
rear
of
the
amplifier.
packing case.
* A Phillips screwdriver and a mallet are required for assembling.
ing Precaution
¢
Be
carefull
not
to
damage
the
floor
and
rack.
Handling
Precautions
* Tempered glass is used for the glass doors for providing sufficient strength.
However, pay attention not to apply excessive force or to scratch the
doors. Cracking or breaking of the glass may occur.
¢ When moving the cabinet, remove all the components from the rack be-
fore carrying the cabinet. Also do not grasp the top shelf when carrying.
* To allow head radiation from the components, leave a space of 4 inches
between the cabinet and wall.
© Do not place the cabinet in a location subject to direct sunlight or near
a heater, an air-conditioner, or a place with high humidity.
IMPORTANT
SAFEGUARDS
..
4
A Caution : Read this page carefully to keep your safety.
Please
read
all
of
the
safety
and
operating
instructions
before
operating
this
unit.
4.
Impact
—
Avoid
placing
the
unit
on
an
unstable
surface.
Install
it
on
a
horizontal
For
bes‘
‘ilts,
follow
all
warnings
placed
on
the
unit
and
adhere
to
the
operating
7*
surface
not
subject
to
excessive
dirt
or
vibrations.
Ra
and
use
uctions.
These
safety
and
operating
instructions
should
be
retained
fol
.
“)
future
reTérence.
Satan
ad
1. Suffocation — After taking the unit out of the polyethylene bag, be sure to di-
spose of the polyethylene bag out of the reach of children. Otherwise, they may
play with the bag, which could cause hazard of suffocation.
5. Modification — Do not attempt to open or modify the unit, for this could cause
tire hazard or malfunction,
2. Water and moisture — Do not place a liquid container, such as a vase and water
basin, on the unit. Also avoid installing the unit in a place subject to dampness.
6. Cleaning — Do not use thinner, benzine or alcohol. When cleaning the unit, wipe
with a soft, dry cloth.
3. Heat — Do not install the unit near a source of heat, such as a heater, or under
direct sunlight.
7. Abnormal smell — In the event the unit generates smoke or abnormal smell, im-
mediately switch the power OFF and unplug the power cord. After this, please
contact your dealer or nearest service station as soon as possible.
POWER OFF!

PARTS LIST MODEL SRC-501 ASSEMBLY INSTRUCTIONS
Part No. ASSEMBLED RACK
©
|
0)
07»
$0033
YD
Description
Net weight: 53 Ibs
(E) (24 kg)
Dimensions
Unit : inch (mm)
BQ \ if
” | 21-9/16”
(547)
Cc
GD
|
)
OPPPPED,
5
(
5
|
Oe?
WOODGRAIN UP
Ss,
Ae
”
anal iT U
NO
WOODGRAIN SURFACES
DOWN AND FORWARD

BLACK SIDE FACING INWARD
STEP 4 WOODGRAIN
SURFACES UP
AND FORWARD
BLACK SIDE
FACING INWAR
or
(J)x14
CONTINUED NEXT PAGE

ASSEMBLY INSTRUCTIONS
that
se
LE
BLACK SURFACES UP AND FORWARD
MODEL: SRC-501 © PARTS LIST
ITEM DESCRIPTION QTY. PART NO.
DESCRIPTION QTY. PART NO.
|
! |
| A LEFT SIDE PANEL 1 XW0404 M MAGNET CATCH 1 POO11 !
| B BOTTOM BOARD 1 XW0311 — N SHELF PIN 4 POO53 j
Cc RIGHT SIDE PANEL 1 XW0405 ce) RUBBER SPACER 4 GO067 1
D KICK PLATE 1 XW0312 P WOOD DOWEL 9 woo0g92 |
| E TOP BOARD 1 XW0403 Qa WOOD DOWEL 2 W0398 ; el
F BACK BOARD 1 XW0406 R GLUE 1 Goo12. If any parts are MISSING or DAMAGED in this |
G SHELF A 1 XW0431 Ss SHELF PIN 4 BOO15 package, circle the item (s) needed on the parts |
|
H
SHELF
B
1
XW0310
T
UPPER
HINGE
1
Moo26
list.
Print
your
name,
address,
and
phone
num-
|
| I CONFIRMAT SCREW 4 $0033 U LOWER HINGE 1 M0027 ber in the area to the left and mail to TOCABI !
| J SCREW 216 16 $0034 VV CATCH PLATE 1 _M0011 AMERICA, 6755 Custom House Plaza Road, |
i K ALLEN WRENCH 1 Mo018 W ~~ CATCH PLATE PAD 1 Go047 Suite | San Ysidro, CA 92173, or call!
| L HINGE INSERT 2 POO54 Xx GLASS DOOR 1 GOO77 (619)-661-6136.
!