Kenwood TK-3180 User manual

© 2004-6 PRINTED IN JAPAN
B51-8690-00 (N)961
UHF FM TRANSCEIVER
TK-3180
SERVICE MANUAL
GENERAL ...................................................2
SYSTEM SET-UP ....................................... 2
REALIGNMENT ..........................................3
DISASSEMBLY FOR REPAIR ....................5
CIRCUIT DESCRIPTION .............................7
SEMICONDUCTOR DATA .......................13
COMPONENTS DESCRIPTION ............... 14
PARTS LIST ..............................................16
EXPLODED VIEW ..................................... 25
PACKING ..................................................26
ADJUSTMENT .........................................27
TERMINAL FUNCTION ............................39
PC BOARD
DISPLAY UNIT (X54-3470-XX) ............ 42
TX-RX UNIT (X57-6940-10) ................. 46
SCHEMATIC DIAGRAM
DISPLAY UNIT (X54-3470-XX) ............ 50
TX-RX UNIT (X57-6940-10) ................. 52
BLOCK DIAGRAM ....................................60
LEVEL DIAGRAM ..................................... 62
OPTIONAL ACCESSORIES
KNB-31A/32N/33L ............................... 63
KSC-32 ..................................................63
SPECIFICATIONS ................. BACK COVER
CONTENTS
Cabinet assy
(A02-3848-03)
Cabinet assy
(A02-3847-03)
Knob (PTT)
(K29-9302-23)
Packing
(G53-1599-01)
Packing
(G53-1598-01)
Button knob (Side)
(K29-9303-03)
Front glass
(B10-2752-22)
Helical antenna
(KRA-23 : Option)
Knob (Volume)
(K29-9304-03)
Knob (CH selector)
(K29-9305-03)
TK-3180 K TK-3180 K3
Does not come with antenna.
Antenna is available as an option.

TK-3180
2
INTRODUCTION
SCOPE OF THIS MANUAL
This manual is intended for use by experienced techni-
cians familiar with similar types of commercial grade commu-
nications equipment. It contains all required service informa-
tion for the equipment and is current as of the publication
date. Changes which may occur after publication are covered
by either Service Bulletins or Manual Revisions. These are
issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment informa-
tion, the full part identification number should be included.
This applies to all parts : components, kits, or chassis. If the
part number is not known, include the chassis or kit number
of which it is a part, and a sufficient description of the re-
quired component for proper identification.
PERSONNEL SAFETY
The following precautions are recommended for person-
nel safety:
•DO NOT transmit until all RF connectors are verified se-
cure and any open connectors are properly terminated.
•SHUT OFF and DO NOT operate this equipment near elec-
trical blasting caps or in an explosive atmosphere.
•This equipment should be serviced by a qualified techni-
cian only.
SERVICE
This transceiver is designed for easy servicing. Refer to
the schematic diagrams, printed circuit board views, and
alignment procedures contained within.
GENERAL / SYSTEM SET-UP
SYSTEM SET-UP
Merchandise received
License and frequency allocated by FCC
Choose the type of transceiver
Transceiver programming
Are you using the optional antenna?
Are you using the speaker microphone?
A personal computer (IBM PC or compatible), programming
interface (KPG-36), and programming software (KPG-89D)
are required for programming.
(The frequency, and signalling data are programmed for the
transceiver.)
Frequency range (MHz) RF power Type 12-key
TX/RX 450~520 5W TK-3180 K No
TX/RX 450~520 5W TK-3180 K3 Yes
YES KRA-23 or KRA-27
Helical antenna
NO
NO
(Option)
(Option)
(Option)
YES KMC-25
Are you using the voice guide & storage unit?
Delivery
NO
YES VGS-1

TK-3180
3
1. Modes 2. How to Enter Each Mode
Mode Operation
User mode Power ON
Panel test mode [A] + Power ON
PC mode Received commands from PC
Panel tuning mode [Panel test mode] + [S]
Firmware programming mode [S] + Power ON
Clone mode [B] + Power ON
Firmware version information [Side1] + Power ON
Clock adjustment mode [C] + Power ON
3. Panel Test Mode
Setting method refer to ADJUSTMENT.
4. Panel Tuning Mode
Setting method refer to ADJUSTMENT.
5. PC Mode
5-1. Preface
The transceiver is programmed by using a personal com-
puter, programming interface (KPG-36) and programming
software (KPG-89D).
The programming software can be used with an IBM PC
or compatible. Figure 1 shows the setup of an IBM PC for
programming.
REALIGNMENT
User mode
Panel test mode
Firmware version information
Panel tuning mode
Data programming mode
PC test mode PC tuning mode
PC mode
Clone mode
Firmware
programming mode
Clock adjustment mode
Mode Function
User mode For normal use.
Panel test mode Used by the dealer to check the funda-
mental characteristics.
Panel tuning mode Used by the dealer to tune the radio.
PC mode Used for communication between the
radio and PC (IBM compatible).
Data programming Used to read and write frequency data
mode and other features to and from the radio.
PC test mode Used to check the radio using the PC.
This feature is included in the FPU.
See panel tuning.
Firmware Used when changing the main program
programming mode of the flash memory.
Clone mode Used to transfer programming data from
one radio to another.
Firmware version Used to confirm the internal firmware
information version.
Clock adjustment mode Used by dealer to adjust data and time.
Fig. 1
MIC
IBM-PC
KPG-36
KPG-89D

TK-3180
4
5-2. Connection procedure
1. Connect the transceiver to the personal computer with
the interface cable.
2. When the POWER switch on, user mode can be entered
immediately. When PC sends command the radio enter
PC mode, and “PROGRAM” is displayed on the LCD.
When data transmitting from transceiver, the red LED is
lights.
When data receiving to transceiver, the green LED is
lights.
Note:
•The data stored in the personal computer must match
model type, when it is written into the flash memory.
5-3. KPG-36 description
(PC programming interface cable: Option)
The KPG-36 is required to interface the transceiver to the
computer. It has a circuit in its D-subconnector (25-pin) case
that converts the RS-232C logic level to the TTL level.
The KPG-36 connects the universal connector of the trans-
ceiver to the computers RS-232C serial port.
5-4. Programming software KPG-89D description
The KPG-89D is the programming software for the trans-
ceiver supplied on a CD-ROM. This software runs under MS-
Windows 98, ME, Windows 2000 or XP on an IBM-PC or
compatible machine.
The data can be input to or read from the transceiver and
edited on the screen. The programmed or edited data can be
printed out. It is also possible to tune the transceiver.
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the transceiver. This allows
the transceiver to be upgraded when new features are re-
leased in the future. (For details on how to obtain the firm-
ware, contact Customer Service.)
6-2. Connection procedure
Connect the transceiver to the personal computer (IBM
PC or compatible) with the interface cable (KPG-36). (Con-
nection is the same as in the PC Mode.)
6-3. Programming
1. Start up the firmware programming software (Fpro.exe).
2. Set the communications speed (normally, 115200 bps)
and communications port in the configuration item.
3. Set the firmware to be updated by File name item.
4. Turn the transceiver power ON with the [S] switch held
down. Then, the orange LED on the transceiver lights and
“PROG 115200” is displayed.
5. Check the connection between the transceiver and the
personal computer, and make sure that the transceiver is
in the Program mode.
6. Press write button in the window. When the transceiver
starts to receive data, the [PG] display is blinking.
7. If writing ends successfully, the checksum is calculated
and a result is displayed.
8. If you want to continue programming other transceivers,
repeat steps 4 to 7.
Notes:
•This mode cannot be entered if the Firmware Program-
ming mode is set to Disable in the Programming software.
•When programming the firmware, it is recommend to
copy the data from the floppy disk to your hard disk before
update the radio firmware.
Directly copying from the floppy disk to the radio may not
work because the access speed is too slow.
6-4. Function
1. If you press the [Side2] switch (under of left side) while
“PROG 115200” is displayed, the display changes to
“PROG 19200” to indicate that the write speed is low
speed (19200 bps). If you press the [Side2] switch again
while “PROG 19200” is displayed, the display changes to
“PROG 38400”. If you press the [Side2] switch again
while “PROG 38400” is displayed, the display changes to
“PROG 57600”. If you press the [Side2] switch again
while “PROG 57600” is displayed, the display returns to
“PROG 115200”.
2. If you press the [Side1] switch (top of left side) while
“PROG 115200” is displayed, the checksum is calculated,
and a result is displayed. If you press the [Side1] switch
again while the checksum is displayed, “PROG 115200”
is redisplayed.
Note:
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one radio to
another by connecting them via their external universal con-
nectors. The operation is as follows (the transmit radio is the
master and the receive radio is a slave).
The “password” of description by explanation of 1. to 7.
are “Read Authorization Password”.
1. Turn the master transceiver power ON with the [B] key
held down. If the Data password is set to the transceiver,
the transceiver displays “CLONE LOCK”. If the password
is not set, the transceiver displays “CLONE MODE”.
2. When you enter the correct password, and “CLONE
MODE” is displayed, the transceiver can be used as the
cloning master. The following describes how to enter the
password.
REALIGNMENT

TK-3180
5
3. How to enter the password with the keypad;
If you press a key while “CLONE LOCK” is displayed, the
number that was pressed is displayed on the transceiver.
Each press of the key shifts the display in order to the left.
When you enter the password and press the [✳] or [S] key,
“CLONE MODE” is displayed if the entered password is
correct. If the password is incorrect, “CLONE LOCK” is
redisplayed.
How to enter the password with the encoder;
If the encoder is rotated while “CLONE LOCK” is dis-
played, numbers (0 to 9) are displayed flashing. When you
press the [C] key, the currently selected number is deter-
mined. If you press the [S] key after entering the pass-
word in this procedure, “CLONE MODE” is displayed if
the entered password is correct. If the password is incor-
rect, “CLONE LOCK” is redisplayed.
4. Power on the slave transceiver.
5. Connect the cloning cable (part No. E30-3325-05) to the
universal connectors on the master and slave.
6. Press the [S] key on the master while the master displays
“CLONE MODE”. The data of the master is sent to the
slave. While the slave is receiving the data, “PROGRAM”
is displayed. When cloning of data is completed, the mas-
ter displays “END”, and the slave automatically operates
in the User mode. The slave can then be operated by the
same program as the master.
7. The other slave can be continuously cloned. When the [S]
key on the master is pressed while the master displays
“END”, the master displays “CLONE MODE”. Carry out
the operation in step 4 to 6.
Notes:
Can not be cloned if the password (over write password)
is programmed to the slave.
Only the same models can be cloned together.
REALIGNMENT / DISASSEMBLY FOR REPAIR
[C] + Power ON
MINUTE
HOUR
DAY
MONTH
YEAR
[S]
[S]
[S]
[S]
[S]
Channel selector
Channel selector
Channel selector
Channel selector
Channel selector
Completion
DISASSEMBLY FOR REPAIR
1. How to Attach the Rubber Spacer
1) Press the rubber spacer with fingers and insert it between
the rubber spacer and the rear panel without crevice.
Rubber spacer
Rear panel
Tighten the circle nut, after
applying “THREE BOND 1401”
to the circle nut.
Cloning cable
(E30-3325-05)
MIC MIC
Fig. 2
8. Firmware Information Mode
Turn the transceiver ON with the [Side1] switch held
down. Then, the version is displayed during holding the
[Side1] switch.
9. Clock Adjustment Mode
9-1. Flow chart of operation

TK-3180
6
4. How to Attach the VGS-1
1) Remove the 2 screws.
2) The tip of tweezers is put into the screw hole of the cover
and is pried, the cover will remove.
3) Use the 2 rubber cushions and attach them to the VGS-1.
4) Plug the VGS-1 into the VGS-1 connector of the PC board,
pressing down on the top of the VGS-1 until secure.
5) The spacer turns the adhesive surface down. Next, push
between the chassis and VGS-1.
6) Replace the cover and tighten the 2 screws.
Rubber cushion
(G13-1995-04)
20 x 30 x 1.0 mm
Rubber cushion
(G13-1974-04)
21 x 21 x 2.5 mm
VGS-1
Spacer
(J30-1292-04)
4.5 x 24 x 3.0 mm
VGS-1
VGS-1 connector
DISASSEMBLY FOR REPAIR
Checks the sheet is
attached to the chassis.
3. How to Attach the TX-RX Unit
1) In order to attach the TX-RX unit in chassis, don’t put in the
TX-RX unit aslant.
Please level the chassis and the TX-RX unit and attach
them.
Sheet (G11-4326-04)
Front-glass
q
w
e
2. How to Stick the Sheet (G11-4326-04)
1) Remove the white separation paper of the sheet first (q)
and stick the sheet on the front-glass (w).
Next, remove the transparent separation paper of the
sheet (e).

TK-3180
7
1. Overview
This transceiver is UHF/FM portable transceiver designed
to operate in the frequency range of 450 to 520MHz.
2. Circuit Configuration by Frequency
The receiver is a double-conversion superheterodyne with
a first intermediate frequency (IF) of 59.85MHz and a second
IF of 455kHz. Incoming signals from the antenna are mixed
with the local signal from the PLL to produce the first IF of
59.85MHz.
This is then mixed with the 59.395MHz second local oscil-
lator output to produce the 455kHz second IF. This is de-
tected to give the demodulated signal.
The transmit signal frequency is generated by the PLL
VCO, and modulated by the signal from the microphone. It is
then amplified and sent to the antenna.
3. Receiver System
3-1. RF unit
An incoming RF signal from the antenna terminal is
passed through the antenna switch (D106, D107 and D213
are off) and then the bandpass filter (L215, L216). The
bandpass filter is adjusted by a variable capacitor. The input
voltage to the variable capacitor is regulated by the voltage
output from the D/A converter (IC605). The signal is ampli-
fied by RF amplifier (Q207), and passed through the band-
pass filter (L210, L211, L212).
The resulting signal is applied to the first mixer (Q206),
where it is mixed with the first local oscillator signal output
from the frequency synthesizer to produce the first IF
(59.85MHz).
3-2. IF unit
The first IF signal is passed through a four-pole monolithic
crystal filter (XF200) to remove a adjacent channel signal. The
filtered first IF signal is amplified by the first IF amplifier
(Q205) and then applied to the lF system IC (IC200). The IF
system IC provides a second mixer, second local oscillator,
limiting amplifier, quadrature detector and RSSI (Received
Signal Strength Indicator). The second mixer mixes the first
IF signal with the 59.395MHz of second local oscillator output
(crystal unit X200) and produces the second IF signal of
455kHz.
The second IF signal is passed through the ceramic filter
(CF201 : Wide, CF200 : Narrow) to more remove the adjacent
channel signal. The filtered second IF signal is amplified by
the limiting amplifier and demodulated by the quadrature de-
tector with ceramic discriminator (CD200). The demodulated
signal is routed to the audio circuit.
ANT
TX/RX : 450~520MHz
ANT
SW
RF
AMP
PA
AMP
TX
AMP
1st MIX MCF
59.85MHz
CF
455kHz
FM IF
SYSTEM
AF
AMP
SP
59.395MHz
390.15~
460.15MHz
PLL
VCO MIC
AMP
MIC
450~520MHz
Fig. 1 Frequency configuration
IC200
MIX, DET, IF SW SW
Q203 IC606
DMUTE
IC600 (1/2)
AF AMP
2nd local
OSC
X200
VOL
IC605
VC1
VC2
Q618
SSW
SW
ANT
SW
L111,112
L113
L215
L216
BPF
D106,107
D213,214
Q207
RF
AMP
Q206
1st MIX
Q205
IF AMP
ANT
L210
L211
L212
BPF
XF200
MCF
1st Local
OSC (PLL)
CF200
CF201
AQUA-L
IC607
HSDO
SW
Q605
(1/2)
AM2
IC609
AF PA
INT. SP
EXT. SP
Fig. 2 Receiver section
CIRCUIT DESCRIPTION

TK-3180
8
3-3. Wide/Narrow switching circuit
Wide and Narrow settings can be made for each channel
by switching the ceramic filters CF201 (Wide), CF200 (Nar-
row). The Wide (low level) and Narrow (high level) is output
from IC502.
When a Wide (low level) is selected, Q200 (N-ch) turn off
and Q200 (P-ch) turn on. When a Narrow (high level) is se-
lected, Q200 (N-ch) turn on and Q200 (P-ch) turn off. D201
and D203 are switched to ceramic filters when a high/low
level is selected.
Q204 turns on/off with the Wide/Narrow and the IC200
detector output level is changed to maintain a constant out-
put level during wide or narrow signals.
When SP-MIC is attached, SSW is connected to GND at
inside of SP-MIC. For this reason, Q618 is turned off, and the
AF signal is input only to amplifier for EXT SP of IC609.
Change of INT/EXT SP refer to Fig. 4.
AM1 AM2 SSW VC1 VC2 SP
HLHHL INT
HLLLHEXT
LHHLLMUTE
LHLLLMUTE
MXO
AFOUT
QUAD
IFOUT
IFI
W/N5R
D314
C201 C200
C215
C217
R208 R211
R215
R212 R209
C209
R205
Q200 D201 D203
CF200
CF201
IC200
R222
R224
Q204
R225 5C
AFOUT
W/N
CD200
“H”: Narrow
“L” : Wide
Fig. 3 Wide/Narrow switching circuit
SW
SW
Q618
VC1
2
VC2
8
B
AF
AM1
SSW
AM2
Q616
(1/2)
Q617
Q605
Q613
Q612
5
VP
IC609
IC605
IC607
INT.SP
EXT.SP
AF
3-4. Audio amplifier circuit
The demodulated signal from IC200 goes through the
mute switch (Q203), IC600 (1/2) and IC606, high-pass fil-
tered, low-pass filtered, high-pass filtered and de-empha-
sized by IC607.
The signal then goes through mute switch (Q605 1/2), and
an electronic volume control (IC605), and an AF switch (Q618
is on), and is routed to audio power amplifier (IC609), where it
is amplified and output to the internal speaker.
The audio mute signal (AM1) from the IC502 becomes
Low in the standby and Q612, Q613 which are power supply
circuit for IC609 turn off. Also, the audio mute signal (AM2)
becomes High to turn Q605 (1/2) off. When the audio is
output, AM1 becomes High to turn Q612, Q613 on, and volt-
age is supplied to power terminal VP of IC609. Also, AM2
becomes Low to turn Q605 (1/2) on.
The speaker is switched by the logic of speaker switching
terminal SSW on the universal connector. When SP-MIC is
not attached, the logic of SSW becomes High and SW (Q618)
is turned on, and the AF signal is input to both amplifiers of
IC609.
3-5. Squelch circuit
The output from IC200 enters FM IC again, then passed
through a bandpass filter. The noise component output from
IC200 is amplified by Q201 and rectified by D202 to produce
a DC voltage corresponding to the noise level. The DC volt-
age is sent to the analog port of the CPU (IC502). And IC200
outputs a DC voltage (RSSI) corresponding to the input of the
IF amplifier. The CPU reads the RSSI signal via pin 125.
IC502 determines whether to output sounds from the
speaker by comparing the input voltage of pin 124 and pin
125 with the preset value.
DET
BPF
AMP DET
NOISE
AMP
IF AMP
RSSI
12
7
Q201 D202
IC200 : FM IF IC
IC502
CPU
125
124
SQ close Preset
value Preset
value
ANT input level ANT input level
SQ voltage
RSSI voltage
SQ open
Fig. 4 Audio amplifier circuit
Fig. 5 Squelch circuit
Fig. 6 Squelch and RSSI voltage vs ANT input level
CIRCUIT DESCRIPTION

TK-3180
9
4. Transmitter System
4-1. Microphone amplifier
The signal from the internal microphone goes through the
mute switch (Q614).
When the SP-MIC is not attached, the microphone switch-
ing terminal (MSW) on the universal connector becomes
High, and mute switch (Q614) is turned on. When the SP-
MIC is attached, MSW is connected to GND at inside of SP-
MIC. For this reason, Q614 is turned off, the internal micro-
phone is muted, and only the input of the external micro-
phone is supplied to the microphone amplifier.
The signal from microphone goes through D/A converter
(IC605), mute switch (Q610), and amplified by IC608 (1/2) and
limited by AGC circuit composed of D601, D602, Q606 and
Q607. IC607 is composed of high-pass filter, low-pass filter
and pre-emphasis/IDC circuit.
The signal passes through the D/A converter (IC605) for
the maximum deviation adjustment, and enters the summing
amplifier consisting of IC600 (2/2), and is mixed with the low
speed data from the CPU (IC502).
The output signal from the summing amplifier goes to the
VCO modulation input. The other output signal from the
summing amplifier passes through the D/A converter (IC605)
again for the BAL adjustment, and the buffer amplifier
(IC602), and goes to the TCXO modulation input.
4-2. VOX
The IC608 (2/2) amplify the audio signal captured in the
microphone, and then the signal is converted into the DC
voltage D603 rectifies.
The DC voltage activates the CPU (IC502), and the VOX
starts.
4-3. Drive and Final amplifier
The signal from the T/R switch (D100 is on) is amplified by
drive amplifier (Q100, Q101 and Q102) to +15~17dBm.
The output of the drive amplifier is amplified by the RF
power amplifier (Q105) to 5.0W (1W when the power is low).
The RF power amplifier is MOS FET. The output of the RF
power amplifier is then passed through the harmonic filter
(LPF) and antenna switch (D106, D107 are on) and applied to
the antenna terminal.
4-4. APC circuit
The APC circuit always monitors the current flowing
through the RF power amplifier (Q105) and keeps a constant
current. The voltage drop at R125, R127 and R130 is caused
by the current flowing through the RF power amplifier and
this voltage is applied to the differential amplifier (IC100 1/2).
IC100 (2/2) compares the output voltage of IC100 (1/2)
with the reference voltage from IC502, and the output of
IC100 (2/2) controls the VGG of Q101, Q102 and Q105 to
make the both voltages to same voltage.
The change of power high/low is carried out by the change
of the reference voltage. Q106, Q107 and Q108 are turned
on and Q104 is turned off in transmit and the APC circuit is
active.
Q614 IC605MIC
SW
Q610
SW
IC608
(1/2)
AMP
IC600
(2/2)
Q616
(2/2)
SUM
AMP
IC602 X1
BUFF
AMP TCXO
VCO
AGC
VOL
MMUTE
AQUA-L
IC607
IC605
D601,602
Q606,607
D/A
O2
I2
IC605
D/A
O1
I1
LSD
OUT
EXT.
MIC
MSW
From
T/R SW
(D100)
RF AMP DRIVE
AMP
Q100
Pre-DRIVE
AMP
Q101 Q102
RF POWER
AMP
Q105
ANT
SW LPF
D106,107
ANT
VDD VGG
IC100
(1/2)
IC100
(2/2)
R130
R127
R125
+B
REF
VOL
(IC502)
Fig. 7 Microphone amplifier
Fig. 8 Drive and final amplifier and APC circuit
CIRCUIT DESCRIPTION

TK-3180
10
5. Frequency Synthesizer Unit
5-1. Frequency synthesizer
The frequency synthesizer consists of the TCXO (X1),
VCO, PLL IC (IC1) and buffer amplifiers.
The TCXO generates 16.8MHz. The frequency stability is
2.5ppm within the temperature range of –30 to +60°C. The
frequency tuning and modulation of the TCXO are done to
apply a voltage to pin 1 of the TCXO. The output of the TCXO
is applied to pin 8 of the PLL IC.
The VCO consists of 2VCO and covers a dual range of the
390.15~460.15MHz and the 450~520MHz. The VCO gener-
ates 390.15~460.15MHz for providing to the first local signal
in receive. The operating frequency is generated by Q7 in
transmit mode and Q6 in receive mode. The oscillator fre-
quency is controlled by applying the VCO control voltage, ob-
tained from the phase comparator (IC1) to the variable capaci-
tor diodes (D9, D12 and D13 in transmit mode and D7, D10
and D11 in receive mode).
The T/R pin of IC502 goes “high” in receive mode causing
Q8 and Q7 to turn off, and Q6 turn on. The T/R pin goes
“low” in transmit mode.
The outputs from Q6 and Q7 are amplified by buffer ampli-
fier (Q10) and doubled by Q14 and Q15, and then sent to PLL
IC.
The PLL IC consists of a prescaler, reference divider,
phase comparator, charge pump (The frequency step of the
PLL circuit is 20 or 25kHz). The input signal from the pins 8
and 5 of the PLL IC is divided down to the 20 or 25kHz and
compared at phase comparator. The pulsed output signal of
the phase comparator is applied to the charge pump and
transformed into DC signal in the loop filter (LPF). The DC
signal is applied to the CV of the VCO and locked to keep the
VCO frequency constant.
PLL data is output from DT (pin 112), PCK (pin 82) and PLE
(pin 81) of the microprocessor (IC502). The data are input to
the PLL IC when the channel is changed or when transmis-
sion is changed to reception and vice versa. A PLL lock con-
dition is always monitored by the pin 80 (UL) of the micropro-
cessor. When the PLL is unlocked, the UL goes low.
LPF
BUFFVCO
PLL
CPU
20
15
5
Doubler
x2
CV
Q13
TCXO
X1
SW
D100
SW D205
To
drive
amp
Q14,15
To mixer
8
FC
BAL
IC602
VC
T/R
T/R
(TX : Low)
IC1
UL
IC502
DT,PCK,PLE
6. Control Circuit
The control circuit consists of microprocessor (IC502) and
its peripheral circuits. It controls the TX-RX unit and transfers
data to the Display unit. IC502 mainly performs the follow-
ing;
1) Switching between transmission and reception by PTT
signal input.
2) Reading system, zone, frequency, and program data from
the memory circuit.
3) Sending frequency program data to the PLL.
4) Controlling squelch on/off by the DC voltage from the
squelch circuit.
5) Controlling the audio mute circuit by decode data input.
6) Transmitting tone and encode data.
6-1. Memory circuit
Memory circuit consists of the CPU (IC502) and a flash
memory (IC500). A flash memory has a capacity of 4M bits
and contains the transceiver control program for the CPU. It
also stores the data for transceiver channels and operating
parameter that are written by the FPU. This program can be
easily written from an external devices.
The EEPROM (IC504) stores the last channel data, the
scan on status, and other parameters.
■Flash memory
Note : The flash memory stores the data that is written by
the FPU (KPG-89D), and firmware program (User mode, Test
mode, Tuning mode, etc.). This data must be rewritten when
replacing the flash memory.
■EEPROM
Note : The EEPROM stores tuning data (Deviation, Squelch,
etc.).
Realign the transceiver after replacing the EEPROM.
■Real-time cock
The clock function is based on real-time clock IC (IC503).
When the power supply is off, it is backed up by an internal
secondary lithium battery
CPU EEPROM
FALSH
IC502
IC500
IC504
Fig. 9 PLL block diagram
Fig. 10 Memory circuit
CIRCUIT DESCRIPTION

TK-3180
11
6-2. Low battery warning
The battery voltage is monitored by the microprocessor
(IC502 pin 126 : BATTLVL). When the battery voltage falls
below the voltage set by the Low Battery Warning adjust-
ment during the transmission, the red LED blinks to notify the
operator that it is time to replace the battery (When the “On
TX” option (default setting) under the Battery Warning / sta-
tus function in the FPU is selected.). If the battery voltage
falls below 5.8V, the transceiver does not transmit and the
warning tone beeps while the PTT switch is pressed.
Low battery warning Battery condition
The red LED blinks during The battery voltage is low but
the transmission. the transceiver is still usable.
The red LED blinks and The battery voltage is low and
the warning tone beeps while the transceiver is not usable
the PTT switch is pressed. to make calls.
6-3. Battery type detection
The transceiver automatically detects the battery type,
measuring the resistance between the S-terminal and GND
terminal on the battery pack and changes the supplied volt-
age to the S-terminal as below. The microprocessor then de-
tects the battery type.
Resistor value Battery type Input voltage of S-terminal
Open Ni-Cd 4.5~5.0V
150kΩNi-MH 2.0~3.34V
47kΩLi-ion 0.8~2.0V
Short Battery case 0~0.8V
6-4. Key input
When any key is pressed, KI1 or KI2 become Low. And
CPU (IC502) set Q1 to Q9 “Low” sequentially. The CPU de-
tects which key is pressed, according to the voltage of KI1
and Kl2 and Q1 to Q9 timing.
7. Signaling Circuit
7-1. Encode
■Low-speed data (QT, DQT, LTR)
Low-speed data is output from pin 33 of the CPU. The
signal passes through a low-pass filter (IC601 1/2), and goes
to the summing amplifier (IC600 2/2). The signal is mixed
with the audio signal and goes to the VCO and TCXO (X1)
modulation input after passing through the D/A converter
(IC605) for BAL adjustment.
SW
SW
SW
SUM
SUM
BUFF
AMP
VCO
TCXO
RXAF
MOD
6
5
7
EXTLIMIN
RX Audio
IC606
LPF
IC601
(1/2)
IC600 (2/2)
IC602 (1/2)
I2 O2
O1 I1
I6 O6 AF AMP
IC605
IC607
AQUA-L
HSDO
IC502
CPU
33
LSDO
■High-speed data (2-tone, 5-tone, DTMF)
High-speed data (HSD) is output from pin 7 of the CPU.
The signal passes through a low-pass CR filter and provides a
TX HSD tone and a RX HSD tone. TX HSD deviation making
an adjustment by microprocessor is passed through the
switch (IC606) and then applied to the audio processor
(IC607).
The signal is mixed with the audio signal and goes to the
VCO and TCXO. The RX HSD tone is passed a summing am-
plifier (IC607). The D/A converter (IC605) for audio control,
audio power amplifier and then to the speaker.
■MSK
MSK signal is output from pin 6 of IC607. The signal
passes through the D/A converter (IC605) for the MSK devia-
tion adjustment, and is routed to the VCO. When encoding
MSK, the microphone input signal is muted.
6 3
S2 B
S1 A
C S
7*
8 0
9 #
5 2
4 1
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Vss
Vdd
LCK
DATA
CLK
Vss
SO
Q10
Q9
Q8
IC500
KI1
KI2
CK
DT
SPSTB
IC502
CPU
Fig. 11 Key input
Fig. 12 Encode
CIRCUIT DESCRIPTION

TK-3180
12
7-2. Decode
■Low-speed data (QT, DQT, LTR)
The demodulated signal from the IF IC (IC200) is amplified
by IC600 (1/2) and passes through a low-pass filter (IC607) to
remove audio components. The signal is input to pin 128 of
the CPU.
The CPU digitizes this signal, performs processing such as
DC restoration, and decodes the signal.
■High-speed data (DTMF)
The DTMF input signal from the IF IC (IC200) is amplified
by IC600 (1/2) and goes to IC607, the DTMF decoder. The
decoded information is then processed by the CPU. During
transmission and standby, the DTMF IC is set to the power
down mode.
LPF
LPF HPF
DTMF
DECODE
AMP COM-
PARATOR
HSDIN
10
128 LSDIN
IC201
AMP
IC600 IC305
DTRLOAD
STD
DTRCLK
DTRDO
XIN XOUT
X600
IC607
IC502
CPU
■High-speed data (2-tone, 5-tone)
The demodulated signal from the IF IC (IC200) is amplified
by IC600 (1/2) and passes through an audio processor (IC607)
and amplifier IC604 (1/2) and comparator IC604 (2/2) to re-
move a low-speed data. The CPU digitizes this signal and
decodes the signal.
■MSK
The MSK input signal from the IF IC is amplified by IC600
(1/ 2) and goes to pin 5 of IC607. The signal is demodulated
by MSK demodulator in IC607. The demodulated data goes
to the CPU for processing.
8. Power Supply Circuit
Battery +B is supplied via a 3A fuse from the battery ter-
minal connected to the TX-RX unit. Power supply (+B) is ap-
plied to the four AVRs. IC402 supplies 5V (5M) to the control
circuit. IC401 and IC403 supplies 5V to common circuits.
IC406 supplies to the TX circuit, the RX circuit and common
circuits. During transmission, 5TC becomes Low and Q406
is turned on to supply 5V (5T) to the TX circuit. During recep-
tion, 5RC becomes Low and Q405 is turned on to supply 5V
(5R) to the RX circuit.
The power supply voltage monitor IC (IC400) monitors
power supply voltage (+B). If the voltage falls (less than
5.6V), the VOUT port goes “LOW” level, the CPU INT port
also goes “HIGH” level, and the CPU stops.
VIN
VOUT
VDD
OUT
IC400
VIN
CE
IC402
VOUT
RESET
INT
PSW
Power SW
VIN
CE
VOUT
VIN
CONT
VOUT
VIN
CONT
VOUT
SAVE
5RC
Q405
Q409
Q406
5TC
5T
5R
5CNS
5C
IC401
IC403
IC406
Q408 5M
D405
IC405
IC502
CPU
Q401
Q407
Q502
D403
RF power amp
+B
F400
3A
Fig. 13 Decode
Fig. 14 Power supply circuit
CIRCUIT DESCRIPTION

TK-3180
13
Pin No. Port Name I/O Function
1VREF - +5V
2AVCC - +5V
3 SBC O Switched B control
45RC O RX control
55TC O TX control
6 APC/TV2 O TX APC adjust / TV adjust 2
7HSDO O High speed data output
8STSW O Side tone switch
9RTCL/EEPCL O RTC/EEPROM clock
10 HSDIN I High speed data input
11 MAN-DN IN I Man down switch input
12 RTDT/EEPDAT I/O RTC/EEPROM data
13 BYTE - +5V
14 CNVSS - DGND (Vss)
15 DMUTE O Det mute
16 AM2 O Audio mute 2
17 RST I Reset
18 Xout O 11.0592MHz clock output
19 DGND - DGND (Vss)
20 Xin I 11.0592MHz clock input
21 VCC1 - +5V
22 NMI - +5V
23 PSW I Power switch input
24 INT I BATT voltage INT
25 INTRA I RTC INT
26 SHIFT/MODEL I/O Beat shift / Model select
27 BEEP O Beep out
28 SPSTB O BU2099 storage enable
29 VCO ADJ O VCO adjust switch
30 LEDR O LED red
31 LEDG O LED green
32 DSTB O STB for DAC
33 LSDO O Low speed data output
34 KEY1 I Key matrix 1 input
35 KEY2 I Key matrix 2 input
36 TXD1 I/O TXD1 and PTT (SC20-460)
37 Vcc1 - +5V
38 RXD1 I RXD1
39 DGND - DGND (Vss)
SEMICONDUCTOR DATA
Pin No. Port Name I/O Function
40 MMUTE O Mic mute
41 AUX I AUX key
42 TXD O TXD (COM0)
43 RXD I RXD (COM0)
44 AFDAT O BB TDATA and DTRCLK
45 AFDIO I/O BB DI/O
46 AFDIR O BB DIR
47 DTRLOAD O BB DTMF enable
48 AFSTD I BB STD
49 LSW O BB LIM switch
50 RDY - +5V
51 NC - Non connection
52 HOLD - +5V
53 NC - Non connection
54~57 EN4~EN1 I Encoder in 4~1
58 NC O Non connection
59 RD O Read (RD)
60 NC O Non connection
61 WR O Write (WR)
62 APCSW O APC switch output
63 DSW O APC voltage discharge switch
64 5UC O 5U control
65 BTSE/VOX O BATT select / VOX input switch
66 LCDRST O LCD reset
67 LCDCS O LCD chip select
68 CS0 O Chip select 0
69 NC - -
70~79 A18~A9 O Address bus 18~9
80 UL I PLL unlock
81 PLE O PLL enable
82 PCK O PLL clock
83 NC - NC
84 OPT6 O Option board I/F 6
85 VCC2 - +5V
86 A8 O Address bus 8
87 DGND - DGND (Vss)
88~95 A7~A0 O Address bus 7~0
96 PTT I PTT input
97 AFRTM I BB RDF/FD
Microprocesser : M30625MGP (TX-RX unit IC502)

TK-3180
14
Pin No. Port Name I/O Function
98 TCLK/DTRDO I BB TCLK and DTRDO
99 SAVE O Save
100 T/R O TX/RX switch
101 AM1 O AF PA switch
102 LCDRS O LCDRS
103 SSW I EXT/INT SP switch input
104~111 D7~D0 I/O Data bus 7~0
112 DT O Serial data
113 CK O Serial clock
114 W/N O Wide/Narrow switch
115~119 OPT 1~OPT 5 I/O Option boad I/F 1~5
120 BATTSEL/VOX I BATT select and VOX input
121 THP/VCO ADJ I Thermal detect and VCO adjust
122 VOL I Volume level input
123 PF I PF key in
124 ASQ I RX Analog SQ. input
125 RSSI I RX RSSI input
126 BATT LVL I BATT level
127 AGND - DGND (Vss)
128 LSDIN I Low speed data input
Key Processor
: BU2099FV (Display unit IC500)
Pin No. Port Name I/O Function
1Vss - GND
2NC -
3DATA I Serial data input
4CLK I Serial clock input
5LCK I Storage enable input
6Q0OLCD back light control
7~15 Q1~Q9 O Key matrix output
16 Q10 O NC
17 Q11 O NC
18 SO O NC
19 OE I /LCDRST
20 VDD I 5V
Display unit (X54-3470-XX)
Ref. No. Part name Description
IC500 IC Key processor
IC501 IC Voltage regulator / LCD
IC502,503 IC LCD control
Q501,502 Transistor Back light control
Q504 FET LCD reset
Q505 FET Contrast control
D500 Diode Contrast control
D501,502 LED Key back light (TK-3180-K3 only)
D511~514 LED Key back light (TK-3180-K3 only)
D515~520 LED Key back light
D522 Diode Key control
TX-RX unit (X57-6940-10)
Ref. No. Part name Description
IC1 IC PLL system
IC100 IC Comparator (APC)
IC200 IC FM IF system
IC400 IC Voltage detector / INT
IC401~403 IC Voltage regulator / 5V
IC404 IC 5T control
IC405 IC Voltage detector / Reset
IC406 IC Voltage regulator / 5V
IC500 IC Flash memory
IC502 IC Microprocessor
IC503 IC RTC processor
IC504 IC EEPROM
IC505 IC Selector
IC600 IC AF buffer
IC601 IC LSD LPF / V REF
IC602 IC LSD buffer to TCXO
IC603 IC Tune
IC604 IC HSD BPF / HSD COMP
IC605 IC D/A converter
IC606 IC AF switch
IC607 IC AQUA-L
IC608 IC MIC AMP / VOX
IC609 IC AF power AMP
Q1,2 Transistor Fin filter shift switch
Q6 FET VCO / RX
Q7 FET VCO / TX
Q8 FET DC switch / TX VCO
Q9 FET DC switch / RX VCO
Q10 Transistor RF buffer AMP
Q11 Transistor DC switch / RX VCO
SEMICONDUCTOR DATA / COMPONENTS DESCRIPTION

TK-3180
15
Ref. No. Part name Description
Q12 FET Ripple filter
Q13 Transistor RF AMP
Q14,15 Transistor PLL IC f_in AMP
Q100 Transistor RF AMP
Q101 FET Pre-drive AMP
Q102 FET TX drive AMP
Q104 Transistor APC switch
Q105 FET TX final AMP
Q106 Transistor APC switch
Q107,108 FET APC switch
Q200 FET W/N filter shift switch
Q201 Transistor SQL noise AMP
Q202 FET W/N noise switch
Q203 FET AF mute
Q204 Transistor W/N switch / RX
Q205 Transistor IF AMP
Q206 FET Mixer
Q207 FET RF AMP
Q400 Transistor LED switch / Green or Red
Q401 FET Power switch
Q402 FET SBC switch
Q403 Transistor SB2 switch
Q404 Transistor 5R switch
Q405 FET 5R switch
Q406 Transistor 5T switch
Q407 FET 5M switch
Q408 Transistor 5M switch
Q409 FET SAVE switch
Q502 FET INT switch
Q602 Transistor LIMIT switch
Q605 Transistor AF switch
Q606,607 Transistor MIC AGC
Q608 FET AF switch
Q609 FET OP switch
Q610 FET MMUTE switch
Q611 FET OP switch
Q612,613 Transistor SP control
Q614 FET MIC shift switch
Q615 Transistor SP control
Q616,617 FET AF mute
Q618 FET SP control
Q619 FET Side tone switch
Q620 Transistor Side tone switch
Q621 Transistor Beet shift switch
Q622 Transistor 5UC switch
Ref. No. Part name Description
Q623,624 FET 5UC switch
D1~4 Diode T / R switch
D7,11 Variable Frequency control / RX VCO
capacitance diode
D9,13 Variable Frequency control / TX VCO
capacitance diode
D17 Variable Modulaor
capacitance diode
D18 Diode Current steering
D100 Diode TX/RX RF switch
D103 Zener diode APC protect
D106,107 Diode ANT switch
D108 Zener diode APC switch
D200 Diode SQL control
D201 Diode Filter switch
D202 Diode SQL rectifier
D203 Diode Filter switch
D204 Diode DMUTE control
D205 Diode TX/RX RF switch
D206~210 Variable RF BPF tuning
D212 capacitance diode
D213,214 Diode ANT switch
D314 Diode 5R protector
D400 LED LED Red & Green
D402 Diode Reverse protection
D403 Diode Power switch control
D404 Diode Batt level control
D405 Diode 5M protector
D406 Diode 5M control
D408 Diode 5T control
D500~502 Diode RTC BATT control
D600 Diode AF BUFFER control
D601~603 Diode Detector
D604 Zener diode MIC shift control
D605 Diode SP control
D606 Zener diode MIC shift control
D607 Zener diode SP control
D608 Zener diode MIC shift control
D609 Diode RXD control
D610 Diode TXD control
D611 Zener diode PTT PF TXD RXD control
D612 Zener diode OPT control
D613 Diode SSW control
D614 Diode SP control
COMPONENTS DESCRIPTION

TK-3180
16
PARTS LIST
✽New Parts. indicates safety critical components.
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Teile ohne Parts No. werden nicht geliefert.
L: Scandinavia K:USA P:Canada
Y: PX (Far East, Hawaii) T:England E:Europe
Y:AAFES (Europe) X:Australia M:Other Areas
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
11B✽A02-3847-03 CABINET ASSY K
21A✽A02-3848-03 CABINET ASSY K3
33A✽A10-4076-11 CHASSIS
43B✽A62-1093-02 PANEL
62DB09-0625-03 CAP ACCESSORY
71A✽B10-2752-22 FRONT GLASS
82A✽B11-1815-04 FILTER (LCD)
92A✽B11-1816-12 ILLUMINATION GUIDE (LCD)
10 3B ✽B11-1820-04 ILLUMINATION GUIDE (BUSY/TX)
11 2A ✽B38-0900-05 LCD ASSY
12 2C ✽B62-1759-00 INSTRUCTION MANUAL
13 3A ✽B72-2260-04 MODEL NAME PLATE K
13 3A ✽B72-2262-04 MODEL NAME PLATE K3
15 2B E04-0416-05 RF COAXIAL RECEPTACLE (SMA)
16 3B E23-1104-04 TERMINAL
17 2A E37-1101-05 SPEAKER WIRE (RED)
18 2A E37-1102-05 SPEAKER WIRE (BLACK)
19 2A ✽E37-1107-05 FLAT CABLE
20 3B ✽E58-0511-05 SQUARE SOCKET
21 3B ✽E72-0419-03 TERMINAL BLOCK
23 3A ✽F07-1880-04 COVER
24 2B ✽F12-0476-04 SHIELDIBG SHEET
25 2B ✽F12-0477-04 SHIELDIBG SHEET
26 2A ✽F15-1012-04 SHADOW PLATE
27 3B ✽F20-3350-04 INSULATING SHEET
29 2A ✽G10-1340-04 FIBROUS SHEET
30 2A ✽G10-1341-04 FIBROUS SHEET
31 2A ✽G11-4272-04 RUBBER CUSHION
32 3A ✽G11-4273-14 SHEET
33 3A ✽G11-4308-14 RUBBER SHEET (FINAL FET)
34 1A ✽G11-4326-04 SHEET
35 3A ✽G11-4332-04 SHEET
36 2B G13-1934-04 CUSHION
37 2A ✽G13-2055-04 CUSHION
38 2A ✽G13-2068-04 CUSHION
39 2B ✽G53-1598-01 PACKING K
40 1A ✽G53-1599-01 PACKING K3
41 3B ✽G53-1600-12 PACKING
42 3B ✽G53-1601-04 PACKING
43 3A ✽G53-1602-14 PACKING
44 2B,3B ✽G53-1603-04 PACKING
46 2C,1D ✽H12-3157-02 PACKING FIXTURE
47 3D ✽H52-2060-02 ITEM CARTON CASE
49 2A ✽J19-5460-02 HOLDER
50 2B ✽J19-5478-03 HOLDER
51 2C ✽J29-0710-05 HOOK ACCESSORY
52 3B ✽J30-1279-04 SPACER
53 2B ✽J82-0089-05 FPC (VOL/ENC)
54 3B ✽J82-0090-15 FPC (UNIVERSAL)
55 3A ✽J82-0091-15 FPC (PTT)
57 1A ✽K29-9302-23 KNOB (SIDE)
58 1A ✽K29-9303-03 BUTTON KNOB (SIDE)
59 1B ✽K29-9304-03 KNOB (VOLUME)
60 1A ✽K29-9305-03 KNOB (CH SELECTOR)
A2DN08-0548-04 DRESSED SCREW ACCESSORY
B3B✽N09-2426-04 HEXAGON HEAD SCREW
C3B✽N14-0806-04 CIRCULAR NUT
D3B✽N14-0810-04 CIRCULAR NUT
E2A,3A N30-2004-45 PAN HEAD MACHINE SCREW
F2BN30-2604-46 PAN HEAD MACHINE SCREW
G3AN30-2608-45 PAN HEAD MACHINE SCREW
H2C✽N30-3008-60 PAN HEAD MACHINE SCREW ACC
J2A,2B N83-2005-46 PAN HEAD TAPTITE SCREW
62 3B ✽R31-0652-05 VARIABLE RESISTOR
64 2B ✽S60-0430-05 ROTARY SWITCH
66 1A ✽T07-0749-15 SPEAKER
68 3A ✽W09-0971-05 LITHIUM CELL
D501,502 B30-2215-05 LED
D511-516 B30-2215-05 LED K3
D517-520 B30-2210-05 LED (TLY)
C500-503 CK73HB1H471K CHIP C 470PF K
C508 CK73HB1H471K CHIP C 470PF K
C513 CK73GB1C104K CHIP C 0.10UF K
C518 CK73HB1H471K CHIP C 470PF K
C522 CK73HB1H102K CHIP C 1000PF K
C523,524 ✽C92-0827-05 CHIP-TAN 4.7UF 10WV
C525 CK73HB1H471K CHIP C 470PF K
C527,528 ✽C92-0826-05 CHIP-TAN 1.0UF 16WV
C537,538 CK73GB0J475K CHIP C 4.7UF K
C539-546 CC73HCH1H470J CHIP C 47PF J
C548-551 CC73HCH1H470J CHIP C 47PF J
C553,554 CK73HB1H102K CHIP C 1000PF K
C555 ✽CK73HB0J105K CHIP C 1.0UF K
C556 CK73HB1H102K CHIP C 1000PF K
C562 ✽CK73HB0J105K CHIP C 1.0UF K
CN507 ✽E40-6410-05 FLAT CABLE CONNECTOR
CN508,509 ✽E40-6413-05 FLAT CABLE CONNECTOR
L550 L92-0163-05 BEADS CORE
L553,554 L92-0419-15 FERRITE CHIP
L555 L92-0163-05 BEADS CORE
CP501 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP503,504 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP506,507 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP509 RK75HA1J102J CHIP-COM 1.0K J 1/16W
R500,501 RK73HB1J102J CHIP R 1.0K J 1/16W
R517 R92-1368-05 CHIP R 0 OHM
R518 RK73HB1J331J CHIP R 330 J 1/16W
R520 RK73HB1J472J CHIP R 4.7K J 1/16W
R522 RK73HB1J391J CHIP R 390 J 1/16W
R524-526 RK73HB1J391J CHIP R 390 J 1/16W K3
DISPLAY UNIT (X54-3470-XX) -10 : K -11 : K3
TK-3180
TK-3180 (Y50-5880-XX)
DISPLAY UNIT (X54-3470-XX)

TK-3180
17
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
R527 R92-1368-05 CHIP R 0 OHM
R531 R92-1368-05 CHIP R 0 OHM
R533 R92-1368-05 CHIP R 0 OHM
R534 RK73HB1J101J CHIP R 100 J 1/16W
R535 R92-1368-05 CHIP R 0 OHM
R537 RK73HB1J101J CHIP R 100 J 1/16W
R540-543 RK73HB1J471J CHIP R 470 J 1/16W
R544 RK73HB1J154J CHIP R 150K J 1/16W
R545 RK73HB1J474J CHIP R 470K J 1/16W
R546 RK73HB1J823J CHIP R 82K J 1/16W
R547 RK73HB1J393J CHIP R 39K J 1/16W
R552 RK73HB1J471J CHIP R 470 J 1/16W
R559 R92-1368-05 CHIP R 0 OHM
R560 RK73HB1J474J CHIP R 470K J 1/16W
R561 RK73HB1J103J CHIP R 10K J 1/16W
R562-568 RK73HB1J102J CHIP R 1.0K J 1/16W
R570 R92-1252-05 CHIP R 0 OHM J 1/16W
R571 R92-1368-05 CHIP R 0 OHM
R573 RK73HB1J474J CHIP R 470K J 1/16W
R574,575 R92-1368-05 CHIP R 0 OHM
MIC500 2A T91-0579-05 MIC ELEMENT
D500 MA2S111 DIODE
D522 DA221 DIODE
IC500 BU2099FV MOS IC
IC501 XC6201P352MR MOS IC
IC502,503 HD74LV2G34AUS MOS IC
Q501 2SC4617(S) TRANSISTOR
Q502 2SB1132(Q,R) TRANSISTOR
Q504 2SK1830 FET
Q505 ✽2SJ144(Y) FET
D400 ✽B30-2278-05 LED (RED/YELLOW)
C1,2 CC73HCH1H101J CHIP C 100PF J
C3 CC73HCH1H100C CHIP C 10PF C
C4 CK73HB1C103K CHIP C 0.010UF K
C5 CC73HCH1H100C CHIP C 10PF C
C6 CK73HB1H102K CHIP C 1000PF K
C7,8 CC73HCH1H470J CHIP C 47PF J
C9-13 CC73HCH1H101J CHIP C 100PF J
C14-16 CC73HCH1H470J CHIP C 47PF J
C17 CC73HCH1H080B CHIP C 8.0PF B
C18 CC73HCH1H101J CHIP C 100PF J
C19 CC73HCH1H090B CHIP C 9.0PF B
C20 CC73HCH1H101J CHIP C 100PF J
C21 CK73HB1C223K CHIP C 0.022UF K
C22 CC73HCH1H1R5B CHIP C 1.5PF B
C23 CC73HCH1H030B CHIP C 3.0PF B
C24 C92-0001-05 CHIP C 0.1UF 35WV
C25 C92-0588-05 CHIP-TAN 1.5UF 16V
C26 CC73HCH1H030B CHIP C 3.0PF B
C27 CC73HCH1H020B CHIP C 2.0PF B
C28 CC73HCH1H050B CHIP C 5.0PF B
C29 CC73HCH1H470J CHIP C 47PF J
C30 C92-0001-05 CHIP C 0.1UF 35WV
C31 CC73HCH1H470J CHIP C 47PF J
C32,33 CC73HCH1H101J CHIP C 100PF J
C35 CC73HCH1H470J CHIP C 47PF J
C37 CC73HCH1H470J CHIP C 47PF J
C38 CC73GCH1H560J CHIP C 56PF J
C41 CC73GCH1H820J CHIP C 82PF J
C43 CK73HB0J105K CHIP C 1.0UF K
C44 CC73HCH1H130J CHIP C 13PF J
C45 CC73HCH1H090B CHIP C 9.0PF B
C46 CC73HCH1H040B CHIP C 4.0PF B
C47 CC73HCH1H020B CHIP C 2.0PF B
C48 CC73HCH1HR75B CHIP C 0.75PF B
C49,50 CC73HCH1H020B CHIP C 2.0PF B
C51 CC73HCH1H050B CHIP C 5.0PF B
C52 CC73HCH1H040B CHIP C 4.0PF B
C53 CC73HCH1H101J CHIP C 100PF J
C54 CC73HCH1H060B CHIP C 6.0PF B
C55 CC73HCH1H040B CHIP C 4.0PF B
C56 CC73HCH1H101J CHIP C 100PF J
C57,58 CC73GCH1H0R5B CHIP C 0.5PF B
C59-62 CC73HCH1H101J CHIP C 100PF J
C63 C92-0713-05 CHIP-TAN 10UF 6.3WV
C64 CC73HCH1H101J CHIP C 100PF J
C65 CC73HCH1H070D CHIP C 7.0PF D
C66 CC73HCH1H100C CHIP C 10PF C
C67 CC73HCH1H330J CHIP C 33PF J
C68-70 CK73HB1H471K CHIP C 470PF K
C71 CC73HCH1H070D CHIP C 7.0PF D
C72-74 CC73HCH1H470J CHIP C 47PF J
C75 CC73HCH1H030B CHIP C 3.0PF B
C78 CC73HCH1H101J CHIP C 100PF J
C79 CK73HB1H222K CHIP C 2200PF K
C100,101 CK73HB1H471K CHIP C 470PF K
C103,104 CK73HB1H471K CHIP C 470PF K
C105 CC73HCH1H070D CHIP C 7.0PF D
C106,107 CK73HB1H471K CHIP C 470PF K
C109 CK73HB1H471K CHIP C 470PF K
C111 CK73HB1A104K CHIP C 0.10UF K
C113 CK73HB1H471K CHIP C 470PF K
C114 CC73HCH1H100C CHIP C 10PF C
C116 CK73HB1H471K CHIP C 470PF K
C117 CK73HB1A104K CHIP C 0.10UF K
C118 CC73HCH1H330J CHIP C 33PF J
C119,120 CC73HCH1H100C CHIP C 10PF C
C121 ✽CK73GB1E105K CHIP C 1.0UF K
C122 CK73HB1H471K CHIP C 470PF K
C123 C92-0565-05 CHIP-TAN 6.8UF 10WV
C125-128 CK73HB1H471K CHIP C 470PF K
C129 CC73HCH1H180J CHIP C 18PF J
C131 CK73HB1H471K CHIP C 470PF K
C132 CC73HCH1H101J CHIP C 100PF J
C133 CK73HB1H471K CHIP C 470PF K
C135 CK73HB1H471K CHIP C 470PF K
C136 CK73HB1C103K CHIP C 0.010UF K
C137 C93-0764-05 CHIP C 47PF 50WV
C138 CK73HB1H471K CHIP C 470PF K
C139 CK73GB1C104K CHIP C 0.10UF K
C140 ✽CK73GB1E105K CHIP C 1.0UF K
C141 C93-0754-05 CHIP C 18PF J
C142 C93-0760-05 CHIP C 33PF 50WV
C143 CK73HB1C103K CHIP C 0.010UF K
C144 CK73HB1H471K CHIP C 470PF K
C149 CC73GCH1H101J CHIP C 100PF J
TX-RX UNIT (X57-6940-10)
DISPLAY UNIT (X54-3470-XX)
TX-RX UNIT (X57-6940-10)

TK-3180
18
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
C150 CK73HB1H471K CHIP C 470PF K
C151 CC73GCH1H030B CHIP C 3.0PF B
C152 CC73GCH1H101J CHIP C 100PF J
C153 CC73HCH1H050B CHIP C 5.0PF B
C154 CC73HCH1H1R5B CHIP C 1.5PF B
C155 CC73HCH1H060B CHIP C 6.0PF B
C156 CC73GCH1H020B CHIP C 2.0PF B
C157 CC73HCH1H070B CHIP C 7.0PF B
C159 CC73HCH1H040B CHIP C 4.0PF B
C161 C93-0745-05 CHIP C 7.0PF 50WV
C200 CK73HB1A104K CHIP C 0.10UF K
C201 CK73HB1C103K CHIP C 0.010UF K
C202 CK73HB1C223K CHIP C 0.022UF K
C203 CK73HB1H102K CHIP C 1000PF K
C204 CK73HB1A104K CHIP C 0.10UF K
C205 CK73HB1C103K CHIP C 0.010UF K
C206 CK73HB1H102K CHIP C 1000PF K
C207 CK73HB1A104K CHIP C 0.10UF K
C208 CK73HB1H182K CHIP C 1800PF K
C209,210 CK73HB1A104K CHIP C 0.10UF K
C211,212 CK73HB1H221K CHIP C 220PF K
C213 CC73HCH1H101J CHIP C 100PF J
C214 C92-0773-05 CHIP-TAN 15UF 6.3WV
C215,216 CK73HB1A104K CHIP C 0.10UF K
C217 CC73HCH1H680J CHIP C 68PF J
C218 CC73HCH1H470J CHIP C 47PF J
C219 CK73HB1A333K CHIP C 0.033UF K
C220 CK73HB1C103K CHIP C 0.010UF K
C221 C92-0713-05 CHIP-TAN 10UF 6.3WV
C222 CK73HB1A104K CHIP C 0.10UF K
C226 CK73HB1H471K CHIP C 470PF K
C227,228 CK73HB1C103K CHIP C 0.010UF K
C229 CC73HCH1H040B CHIP C 4.0PF B
C230 CC73HCH1H270J CHIP C 27PF J
C231 CC73HCH1H040B CHIP C 4.0PF B
C232 CK73HB1C103K CHIP C 0.010UF K
C233 CK73HB1H471K CHIP C 470PF K
C234 CK73HB1A104K CHIP C 0.10UF K
C235,236 CK73HB1C103K CHIP C 0.010UF K
C237 CK73HB1H471K CHIP C 470PF K
C238 CC73HCH1H060D CHIP C 6.0PF D
C239 CC73HCH1H090B CHIP C 9.0PF B
C240 CC73HCH1H020B CHIP C 2.0PF B
C241 CC73HCH1H100C CHIP C 10PF C
C242 CK73HB1H471K CHIP C 470PF K
C243 CK73HB1C103K CHIP C 0.010UF K
C244 CC73HCH1H020B CHIP C 2.0PF B
C245 CK73HB1H471K CHIP C 470PF K
C246 CC73HCH1H100C CHIP C 10PF C
C247 CC73HCH1H040B CHIP C 4.0PF B
C248 CK73HB1H471K CHIP C 470PF K
C250 CK73HB1H471K CHIP C 470PF K
C251 CC73HCH1H3R5B CHIP C 3.5PF B
C252 CC73HCH1H330J CHIP C 33PF J
C253 CK73HB1H471K CHIP C 470PF K
C255 CC73GCH1HR75B CHIP C 0.75PF B
C256 CC73GCH1H3R5B CHIP C 3.5PF B
C257 CC73HCH1H330J CHIP C 33PF J
C258 CK73HB1H471K CHIP C 470PF K
C260 CC73GCH1H010B CHIP C 1.0PF B
C261 CK73HB1H471K CHIP C 470PF K
C262 CC73HCH1H330J CHIP C 33PF J
C263 CC73HCH1H040B CHIP C 4.0PF B
C264 C92-0714-05 CHIP-TAN 4.7UF 6.3WV
C265,266 CK73HB1H471K CHIP C 470PF K
C269,270 CK73HB1H471K CHIP C 470PF K
C271 ✽CK73HB0J105K CHIP C 1.0UF K
C273-275 CK73HB1H471K CHIP C 470PF K
C276 CC73GCH1H2R5B CHIP C 2.5PF B
C277 CC73HCH1H330J CHIP C 33PF J
C279 CC73GCH1H1R5B CHIP C 1.5PF B
C280 CK73HB1H471K CHIP C 470PF K
C281 CC73HCH1H330J CHIP C 33PF J
C282 CC73HCH1H010B CHIP C 1.0PF B
C283 CC73HCH1H050B CHIP C 5.0PF B
C284 CC73GCH1H030B CHIP C 3.0PF B
C285 CK73HB1H471K CHIP C 470PF K
C286 CC73GCH1H101J CHIP C 100PF J
C287 CC73GCH1H090B CHIP C 9.0PF B
C289 CC73HCH1H040B CHIP C 4.0PF B
C290 ✽CK73HB0J224K CHIP C 0.22UF K
C292 CK73HB1C103K CHIP C 0.010UF K
C294 CC73GCH1H200J CHIP C 20PF J
C401,402 CK73HB1H471K CHIP C 470PF K
C404-414 CK73HB1H471K CHIP C 470PF K
C415 CK73FB1A475K CHIP C 4.7UF K
C416 CK73HB1H102K CHIP C 1000PF K
C418 CK73HB1H102K CHIP C 1000PF K
C419 ✽CK73GB1E105K CHIP C 1.0UF K
C420 CK73GB1C104K CHIP C 0.10UF K
C421 CK73GB1A224K CHIP C 0.22UF K
C422 ✽CK73GB1E105K CHIP C 1.0UF K
C423 ✽C92-0825-05 CHIP-TAN 10UF 10WV
C425 ✽CK73GB1E105K CHIP C 1.0UF K
C426 CC73HCH1H101J CHIP C 100PF J
C427 ✽CK73GB1E105K CHIP C 1.0UF K
C428 CK73HB1H471K CHIP C 470PF K
C429 ✽CK73GB1E105K CHIP C 1.0UF K
C431 CK73HB1H471K CHIP C 470PF K
C432 ✽C92-0825-05 CHIP-TAN 10UF 10WV
C433 CK73HB1H471K CHIP C 470PF K
C434 CC73HCH1H101J CHIP C 100PF J
C435 CK73GB1A224K CHIP C 0.22UF K
C436 CK73GB1H103K CHIP C 0.010UF K
C437 CC73HCH1H101J CHIP C 100PF J
C441 ✽CK73GB1E105K CHIP C 1.0UF K
C442 CK73GB1A224K CHIP C 0.22UF K
C443 ✽CK73GB1E105K CHIP C 1.0UF K
C445 CC73HCH1H470J CHIP C 47PF J
C446 CK73HB1H471K CHIP C 470PF K
C447 CK73HB1E472K CHIP C 4700PF K
C450,451 CK73GB0J475K CHIP C 4.7UF K
C500 C92-0712-05 CHIP-TAN 22UF 6.3WV
C502 C92-0712-05 CHIP-TAN 22UF 6.3WV
C503 CK73GB1E105K CHIP C 1.0UF K
C505-508 CK73GB1E105K CHIP C 1.0UF K
C509 CC73HCH1H270J CHIP C 27PF J
C510 CC73HCH1H040C CHIP C 4.0PF C
C511 CC73HCH1H270J CHIP C 27PF J
C512 CK73HB1C103K CHIP C 0.010UF K
TX-RX UNIT (X57-6940-10)

TK-3180
19
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
C514 CK73HB1C103K CHIP C 0.010UF K
C515 CC73HCH1H150G CHIP C 15PF G
C516 CK73HB1C103K CHIP C 0.010UF K
C517 CK73HB1A104K CHIP C 0.10UF K
C518 ✽CK73HB0J105K CHIP C 1.0UF K
C600 CK73HB1A104K CHIP C 0.10UF K
C601 CC73HCH1H220J CHIP C 22PF J
C602 CK73HB1A104K CHIP C 0.10UF K
C603 CK73HB1E472K CHIP C 4700PF K
C604,605 CC73HCH1H680J CHIP C 68PF J
C608 CK73HB1A104K CHIP C 0.10UF K
C609,610 CK73HB1C103K CHIP C 0.010UF K
C611 CC73HCH1H101J CHIP C 100PF J
C612,613 CK73HB1A104K CHIP C 0.10UF K
C614 CK73HB1H471K CHIP C 470PF K
C615 CC73HCH1H101J CHIP C 100PF J
C616 CK73HB1H471K CHIP C 470PF K
C617 C92-0656-05 CHIP-TAN 2.2UF 6.3WV
C618 C92-0713-05 CHIP-TAN 10UF 6.3WV
C619 CK73HB1H561K CHIP C 560PF K
C620 CK73HB1A104K CHIP C 0.10UF K
C621 CK73HB1C103K CHIP C 0.010UF K
C622 CK73HB1E562K CHIP C 5600PF K
C625 CK73HB1A104K CHIP C 0.10UF K
C627 CK73HB1C103K CHIP C 0.010UF K
C628 CK73HB1A104K CHIP C 0.10UF K
C630 CK73HB1H271K CHIP C 270PF K
C631 CK73HB1A104K CHIP C 0.10UF K
C632 CK73GB1E105K CHIP C 1.0UF K
C633 CK73HB1C103K CHIP C 0.010UF K
C635 CC73HCH1H101J CHIP C 100PF J
C636 CK73HB1A104K CHIP C 0.10UF K
C638 CK73HB1H102K CHIP C 1000PF K
C640,641 CK73GB0J475K CHIP C 4.7UF K
C642 CK73HB1A473K CHIP C 0.047UF K
C644 CK73HB1C123K CHIP C 0.012UF K
C645 CK73HB1A104K CHIP C 0.10UF K
C646 CK73GB0J475K CHIP C 4.7UF K
C647 CK73HB1C123K CHIP C 0.012UF K
C648 CK73HB1H102K CHIP C 1000PF K
C650,651 CK73HB1A104K CHIP C 0.10UF K
C652 CC73HCH1H680J CHIP C 68PF J
C653-655 CK73HB1A104K CHIP C 0.10UF K
C656 ✽CK73HB0J224K CHIP C 0.22UF K
C657 CC73HCH1H330J CHIP C 33PF J
C658 CK73HB1A104K CHIP C 0.10UF K
C659,660 CK73GB1C104K CHIP C 0.10UF K
C661 CK73HB1A104K CHIP C 0.10UF K
C662 CK73HB1H102K CHIP C 1000PF K
C663 ✽CK73HB0J105K CHIP C 1.0UF K
C665 CK73GB1E223K CHIP C 0.022UF K
C666 CK73HB1A104K CHIP C 0.10UF K
C667 CC73HCH1H470J CHIP C 47PF J
C668 CC73HCH1H120J CHIP C 12PF J
C669 CK73HB1H102K CHIP C 1000PF K
C670 CK73HB1A104K CHIP C 0.10UF K
C672 CK73HB1H102K CHIP C 1000PF K
C673-675 CK73HB1A104K CHIP C 0.10UF K
C676 CC73HCH1H470J CHIP C 47PF J
C677 CK73HB1H222K CHIP C 2200PF K
C678 CK73GB1C104K CHIP C 0.10UF K
C679,680 CK73HB1A104K CHIP C 0.10UF K
C681 CK73HB1H102K CHIP C 1000PF K
C682 CK73HB1C153K CHIP C 0.015UF K
C683 CK73HB1C123K CHIP C 0.012UF K
C684 CK73HB1H102K CHIP C 1000PF K
C685 CK73HB1A104K CHIP C 0.10UF K
C686 CK73HB1A683K CHIP C 0.068UF K
C687 C92-0713-05 CHIP-TAN 10UF 6.3WV
C688 CK73GB1A474K CHIP C 0.47UF K
C689 CK73HB1C103K CHIP C 0.010UF K
C690 CC73HCH1H470J CHIP C 47PF J
C691 CK73GB1A474K CHIP C 0.47UF K
C692 CC73HCH1H470J CHIP C 47PF J
C693 CK73GB1A474K CHIP C 0.47UF K
C694 CK73HB1H152K CHIP C 1500PF K
C695 CK73HB1A104K CHIP C 0.10UF K
C696 CK73HB1C103K CHIP C 0.010UF K
C697,698 CK73HB1A104K CHIP C 0.10UF K
C699 ✽C92-0816-05 CHIP-TAN 10UF 16WV
C700 CC73HCH1H470J CHIP C 47PF J
C702-710 CC73HCH1H470J CHIP C 47PF J
C711-714 CK73HB1H102K CHIP C 1000PF K
C715-717 CK73HB1A104K CHIP C 0.10UF K
C718 CC73HCH1H180J CHIP C 18PF J
C719 CC73HCH1H220J CHIP C 22PF J
C720 CK73HB1H471K CHIP C 470PF K
C721 CK73HB1H102K CHIP C 1000PF K
C725 CK73HB1H392K CHIP C 3900PF K
C727 CK73HB1A104K CHIP C 0.10UF K
C728 ✽CK73HB0J105K CHIP C 1.0UF K
C729 CK73HB1H271K CHIP C 270PF K
C730 CK73HB1H332K CHIP C 3300PF K
C732 CK73HB1H471K CHIP C 470PF K
C734 CC73HCH1H220J CHIP C 22PF J
C736 CC73HCH1H470J CHIP C 47PF J
C737 CK73GB0J475K CHIP C 4.7UF K
C738 CK73HB1H331K CHIP C 330PF K
C739-751 CC73HCH1H470J CHIP C 47PF J
C752,753 CC73HCH1H050B CHIP C 5.0PF B
C754 CK73HB1A104K CHIP C 0.10UF K
C755 CK73HB1E472K CHIP C 4700PF K
C756 CK73HB1A104K CHIP C 0.10UF K
C757 CK73HB1E472K CHIP C 4700PF K
C759 CK73HB1C123K CHIP C 0.012UF K
C763 CK73HB1H471K CHIP C 470PF K
TC1,2 C05-0384-05 CERAMIC TRIMMER CAP (10PF)
CN400 E40-5823-05 FLAT CABLE CONNECTOR
CN500 E40-6413-05 FLAT CABLE CONNECTOR
CN502,503 ✽E23-0342-05 TEST TERMINAL
CN600 E40-6389-05 PIN ASSY
CN602 E40-5856-05 FLAT CABLE CONNECTOR
CN603 ✽E23-1263-05 TERMINAL
F400 F53-0190-05 FUSE
F601,602 ✽F53-0315-05 FUSE
CN501 J19-5386-05 HOLDER
CD200 L79-1072-05 TUNING COIL
TX-RX UNIT (X57-6940-10)

TK-3180
20
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
CF200 ✽L72-1013-05 CERAMIC FILTER
CF201 ✽L72-1014-05 CERAMIC FILTER
L1 L40-4795-85 SMALL FIXED INDUCTOR (4.7UH)
L2 L41-2767-31 SMALL FIXED INDUCTOR
L3 L41-3367-31 SMALL FIXED INDUCTOR
L4 L41-1878-31 SMALL FIXED INDUCTOR
L6 L41-1878-31 SMALL FIXED INDUCTOR
L8 L40-1075-92 SMALL FIXED INDUCTOR (10NH)
L9 L92-0138-05 FERRITE CHIP
L10 L40-1891-86 SMALL FIXED INDUCTOR (1.8UH)
L11 L40-3391-86 SMALL FIXED INDUCTOR (3.3UH)
L12 L92-0163-05 BEADS CORE
L13 L40-1891-86 SMALL FIXED INDUCTOR (1.8UH)
L14 L40-3391-86 SMALL FIXED INDUCTOR (3.3UH)
L17 L40-1578-67 SMALL FIXED INDUCTOR (15NH)
L18 L40-2278-67 SMALL FIXED INDUCTOR (22NH)
L19,20 L40-2785-92 SMALL FIXED INDUCTOR (270NH)
L21,22 L40-3391-86 SMALL FIXED INDUCTOR (3.3UH)
L23 L92-0163-05 BEADS CORE
L24,25 L40-2275-92 SMALL FIXED INDUCTOR (22NH)
L27 L40-1075-92 SMALL FIXED INDUCTOR (10NH)
L100,101 L40-1875-92 SMALL FIXED INDUCTOR (18NH)
L102 L92-0138-05 FERRITE CHIP
L103 L40-1275-92 SMALL FIXED INDUCTOR (12NH)
L104 L40-1575-54 SMALL FIXED INDUCTOR (15NH)
L105 L92-0149-05 FERRITE CHIP
L106 L40-2275-92 SMALL FIXED INDUCTOR (22NH)
L107 L34-4566-05 AIR-CORE COIL
L108 L92-0149-05 FERRITE CHIP
L109 L40-2285-54 SMALL FIXED INDUCTOR (220NH)
L110 L34-4572-05 AIR-CORE COIL
L111-113 L34-4564-05 AIR-CORE COIL
L200 L92-0141-05 FERRITE CHIP
L201 L40-1091-86 SMALL FIXED INDUCTOR (1.0UH)
L202 L40-1591-86 SMALL FIXED INDUCTOR (1.5UH)
L203 L92-0138-05 FERRITE CHIP
L204 L40-2785-85 SMALL FIXED INDUCTOR (0.27UH)
L206,207 L40-1875-92 SMALL FIXED INDUCTOR (18NH)
L208 L40-2275-92 SMALL FIXED INDUCTOR (22NH)
L210-212 L41-8268-14 SMALL FIXED INDUCTOR
L213 L92-0138-05 FERRITE CHIP
L214 L41-2285-03 SMALL FIXED INDUCTOR
L215,216 L41-8268-14 SMALL FIXED INDUCTOR
L217 L41-3378-03 SMALL FIXED INDUCTOR
L218 L40-8625-92 SMALL FIXED INDUCTOR (8.2NH)
L220 L40-5685-85 SMALL FIXED INDUCTOR (0.56UH)
L400 L92-0149-05 FERRITE CHIP
L500-503 L92-0163-05 BEADS CORE
L600 L92-0163-05 BEADS CORE
L601 ✽L92-0419-15 FERRITE CHIP
L602-607 L92-0163-05 BEADS CORE
L608,609 L92-0467-05 FERRITE CHIP
L610,611 L92-0408-05 FERRITE CHIP
L612 L92-0163-05 BEADS CORE
L615 L92-0163-05 BEADS CORE
X1 ✽L77-1952-05 TCXO (16.8MHZ)
X200 ✽L77-1957-05 CRYSTAL RESONATOR (59.395MHZ)
X500 ✽L77-1958-05 CRYSTAL RESONATOR (11.0592MHZ)
X501 ✽L77-1802-05 CRYSTAL RESONATOR (32768HZ)
X600 ✽L77-1965-05 CRYSTAL RESONATOR (3.6864MHZ)
XF200 ✽L71-0622-05 MCF (59.85MHZ)
CP400,401 RK75HA1J473J CHIP-COM 47K J 1/16W
CP500-510 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP511 ✽RK75HA1J331J CHIP-COM 330 J 1/16W
CP512-515 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP516 RK75HA1J103J CHIP-COM 10K J 1/16W
CP517 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP518 RK75HA1J473J CHIP-COM 47K J 1/16W
CP519 RK75HA1J103J CHIP-COM 10K J 1/16W
CP521 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP522 RK75HA1J101J CHIP-COM 100 J 1/16W
CP600 RK75HA1J473J CHIP-COM 47K J 1/16W
CP601-603 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP604,605 ✽RK75HA1J331J CHIP-COM 330 J 1/16W
CP606 RK75HA1J102J CHIP-COM 1.0K J 1/16W
CP607,608 ✽RK75HA1J101J CHIP-COM 100 J 1/16W
R2 RK73HB1J101J CHIP R 100 J 1/16W
R3 R92-1368-05 CHIP R 0 OHM
R4 RK73HB1J100J CHIP R 10 J 1/16W
R5 RK73HB1J103J CHIP R 10K J 1/16W
R6,7 RK73HB1J223J CHIP R 22K J 1/16W
R8-10 RK73HB1J100J CHIP R 10 J 1/16W
R11 RK73HB1J102J CHIP R 1.0K J 1/16W
R12 RK73HB1J272J CHIP R 2.7K J 1/16W
R13 RK73HB1J154J CHIP R 150K J 1/16W
R14,15 RK73HB1J100J CHIP R 10 J 1/16W
R16 RK73HB1J821J CHIP R 820 J 1/16W
R17,18 RK73HB1J271J CHIP R 270 J 1/16W
R19,20 RK73HB1J223J CHIP R 22K J 1/16W
R21 RK73HB1J681J CHIP R 680 J 1/16W
R22 RK73HB1J103J CHIP R 10K J 1/16W
R23,24 RK73HB1J472J CHIP R 4.7K J 1/16W
R29 RK73HB1J184J CHIP R 180K J 1/16W
R30,31 RK73HB1J473J CHIP R 47K J 1/16W
R32 RK73HB1J100J CHIP R 10 J 1/16W
R33 RK73HB1J181J CHIP R 180 J 1/16W
R34 RK73HB1J151J CHIP R 150 J 1/16W
R35 RK73HB1J100J CHIP R 10 J 1/16W
R36 RK73HB1J154J CHIP R 150K J 1/16W
R37 RK73HB1J472J CHIP R 4.7K J 1/16W
R38 RK73HB1J101J CHIP R 100 J 1/16W
R39 RK73HB1J472J CHIP R 4.7K J 1/16W
R40 RK73HB1J682J CHIP R 6.8K J 1/16W
R41 RK73HB1J103J CHIP R 10K J 1/16W
R42 RK73HB1J331J CHIP R 330 J 1/16W
R43 RK73HB1J222J CHIP R 2.2K J 1/16W
R44 RK73HB1J470J CHIP R 47 J 1/16W
R45 R92-1368-05 CHIP R 0 OHM
R46 RK73HB1J472J CHIP R 4.7K J 1/16W
R47 RK73HB1J474J CHIP R 470K J 1/16W
R51 R92-1368-05 CHIP R 0 OHM
R53 R92-1368-05 CHIP R 0 OHM
R100 RK73HH1J333D CHIP R 33K D 1/16W
R101 RK73HB1J472J CHIP R 4.7K J 1/16W
R102 RK73HB1J223J CHIP R 22K J 1/16W
R103 RK73HB1J822J CHIP R 8.2K J 1/16W
R104 RK73HB1J473J CHIP R 47K J 1/16W
R105 RK73HB1J100J CHIP R 10 J 1/16W
R106 RK73HB1J331J CHIP R 330 J 1/16W
TX-RX UNIT (X57-6940-10)