KERN YKS-01 User manual

KERN & Sohn GmbH
Ziegelei 1
D-72336 Balingen
email: [email protected]om
Phone: +49-[0]7433- 9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
Operating instructions Statistics printer
KERN YKS-01
Version 1.0
05/2010
GB
YKS-01-BA-e-1010

2 YKS-01-BA-e-1010
GB KERN YKS-01
Version 1.0 05/2010
Operating Manual
Statistics printer
Table of Contents
1Technical Data.........................................................................................................3
2Unpacking................................................................................................................4
3Installation and commissioning.............................................................................4
4Printer parts.............................................................................................................4
5Preparing your printer for operation.....................................................................5
6Operating elements.................................................................................................7
7Start-up ....................................................................................................................7
8Statistics function...................................................................................................8
8.1 Arithmetic mean value of the basic totality:.................................................................................... 9
8.2 Standard deviation of the basic totality ........................................................................................... 9
8.3 Standard deviation of a random sample.......................................................................................... 9
9GLP log ..................................................................................................................10
10 Storage conditions and use of thermal paper....................................................11
11 Printer cable ..........................................................................................................11
12 Instant help............................................................................................................12

YKS-01-BA-e-1010 3
Printer YKS-01 is a standard thermal printer
1 Technical Data
Printout Bi-directional thermal print with moveable 8 dot matrix head
Character
composition 8x8 dot matrix
Print speed 0.75 lines
Number of
characters per
line 40, 80
Character set IBM set 2
Thermal paper One roll, width 112mm, length 20m
Max. winding
diameter 42 m
Electric Supply 8.5 V – 14 V DC
External power
supply unit 230 V 50 Hz 0.12 A / 9V DC 1.3 A
Energy
consumption 3 W 15W
Supply interface Type Jack 2.1
Baud rate 1200, 2400, 4800, 9600 Baud
Parameter/data
format 8 or 7 bits, with or without parity control
Parity Even or odd
Transfer
protocol Hardware-related DTR
Working life 5000 hours or 500 000 lines
Operating
temperature 5°C – 35°C
Humidity of air max. 80 % relative (not condensing)
Dimensions 165 x 140 x 50 mm
Weight 0.45 kg (excl. paper roll)

4 YKS-01-BA-e-1010
2 Unpacking
Delivery includes:
1 - Printer
2 – Power supply unit
3 – Printer cable
4 - 1 x Roll of thermal paper
5 – Operating instructions
If one the articles listed above is missing please contact your supplier immediately.
3 Installation and commissioning
Environmental conditions at the workplace chosen for the printer must meet the conditions
stated below:
Temperature: 5°C – 35°C
Humidity: 10 – 80 % (excl. condensation)
Take notice of the following as regards to the site of operation:
Dust and humidity free
Do not place printer next to powerful sources of heat
Do not place the device within range of strong electric, magnetic, electromagnetic
impulse fields or planes that collect electrostatic charge.
Do not expose printer to direct sunlight or impacts.
Power is supplied via the external mains adapter.
The stated voltage value must be the same as the local voltage.
Only use original KERN mains adapters.
Using other makes requires consent by KERN.
4 Printer parts
1 – ON/OFF switch
2 – Cover of paper compartment
3 – LED display ON/OFF
4 – Interface for connection to weighing balance
5 – Interface for printer supply
6 – Feed button
7 – Functional button

YKS-01-BA-e-1010 5
5 Preparing your printer for operation
Remove the cover from the paper
compartment
Set the micro switches
The micro switches are used to set the operating mode for the printer.
1200 2400 4800 9600
SW1 ON OFF ON OFF
SW2 ON ON OFF OFF
SW3
OFF
ON
OFF
ON
SW4
OFF
OFF
ON
ON
FORMAT
8 bits – no parity
7 bits – odd parity
7 bits – even parity
7 bits – ignore parity
SW5 ON Summer time
OFF Winter time
SW6 ON Statistics ON
OFF Statistics OFF
Language
SW7
SW8
POL.
ON
ON
GER.
OFF
ON
ENG.
ON
OFF
FRA.
OFF
OFF
Changes to the settings for the micro switches must be made with the power
supply turned off.
The changes are taken over when started-up again.
Connecting the cables:
There are two interfaces at the back wall of the housing:
Terminal printer cable
Terminal power supply unit
Always use KERN accessories and weighing balances when working with your
printer. Disconnect the printer from the mains voltage before connecting the
cable to the printer.

6 YKS-01-BA-e-1010
Preparing the paper:
⇒Fold over one end of the paper before
inserting it into the printer
Inserting the paper
⇒Insert the folded-over end of the paper into
the mechanism
⇒Turning on the printer supply
⇒Press and hold the FEED key until the
paper emerges from the outlet slot of the
mechanism
Tearing off paper
⇒Pull the printout across the direction of
printout that it rests on the cutter bar of
the printer housing
Do not pull printout upwards.

YKS-01-BA-e-1010 7
6 Operating elements
After the power supply unit has been connected to the printer and the mains, and after
the
ON/OFF switch of the printer has been switched to “ON” position, the
red indicator for the power supply will light up.
This indicator also signals that the printer is ready for operation.
7 Start-up
⇒On start-up press the FEED key; printer carries out self-test
and parameters will be printed.
Red LED is lit up, printer is ready for operation.
⇒Press “FEED” key: Switch numerator on or off, when statistics function is „ON“
⇒Press and hold “FEED” button: Paper transport.
⇒Press “FEED” button: Switch date and time on or off, when statistics function is
„ON“

8 YKS-01-BA-e-1010
8 Statistics function
To create statistics, the numerator must be switched on.
After having processed several weighings, statistics will be printed by pressing the
functional button:
Example Numerator ON:
Numerator ON
001: 0.366 g
002: 0.363 g
003: 0.357 g
004: 0.354 g
18/05/10 15:01
n 004
∑00001.44 g
x 00000.31 g
σn-1 00000.14
σn00000.44
Min 00000.00 g
Max 00000.36 g
R 00000.36 g
Explication:
n Number of test results
∑Sum of all test results
x Mean value of all test results
σn-1 Standard deviation of the
basic totality
σnStandard deviation of a
random sample
Min Minimum value of the basic
totality
Max Maximum value of the basic
totality
R Span of the basic totality
(maximum value – minimum
value)

YKS-01-BA-e-1010 9
8.1 Arithmetic mean value of the basic totality:
8.2 Standard deviation of the basic totality
8.3 Standard deviation of a random sample

10 YKS-01-BA-e-1010
9 GLP log
To create a GLP log, press the functional button when switching on.
The following log is created and can be completed hand-written:
Documentation of
Adjustment (GLP)
Date: 18/05/10 Hour: 14:26
Balance
Manufacturer: ___________________
_________________________________________
Model: ___________________
_________________________________________
Serial no.: ___________________
_________________________________________
ID: ___________________
_________________________________________
Adjustment weight
external internal
Serial no..: ___________________
Rated value: ___________________
Class: ___________________
_________________________________________
Adjustment successful:
yes no
_________________________________________
Auditor: ___________________
Signature: ___________________