Kessil H350 User manual

H350
OWNER’S MANUAL
LED ILLUMINATOR
1.DO NOT use a power supply that is outside the
specifications. This is a fire hazard and may lead
to unit failure.
2.DO NOT use outdoors. This unit is intended for
indoor use only.
3.DO NOT expose unit to an extremely humid
environment or submerse unit in water. This may
lead to unit failure.
4.DO NOT place working illuminator in close contact
with any objects. This may cause objects to heat
up and the unit to overheat.
5.KEEP diffuser (G) away from sharp objects. This
may break the diffuser and lead to unit failure.
6.DO NOT cover or place objects on the power
supply. Power supply should not be contained in
an airtight space.
SAFETY INSTRUCTIONS
1. Remove contents from package.
2. Screw the hanging bolt (C) into the center hole.*
3. Hang H350 1 to 2 ft. above the object to be
illuminated.**
4. Connect H350 to the specified DC power supply (H).
5. Plug the power supply into an outlet with the
correct specifications (see product specifications
for more information).
* H350 may also be hung by mounting 2 metal hooks (diameters of
at least 2.5 mm and thread numbers of at least 6) through its
brackets (E).
** H350 should only be installed on wood, acoustical tile or other
similar ceilings.
** For sufficient airflow, the intake and venting holes (D, F) should be
at least 12 in. from surrounding obstructions.
INSTALLATION GUIDE
PRODUCT SPECIFICATIONS
Power consumption
Input Voltage
Illuminator
92 W MAX
54 VDC
Listed Power Supply
Input
Output
100-240 VAC 47-63 Hz 1.3A MAX
54 VDC, 1.7A
Kessil Lighting
A DiCon Business Division
1689 Regatta Blvd, Richmond, CA 94804
[phone]
WWW.KESSIL.COM
Power Cord
A
Hanging Bolt
C
Air Intake Hole
D
Bracket
E
Vent Hole
F
Diffuser
G
DC Power Supply
H
Gold Metal Hook
B

Follow Us
www.facebook.com/Kessil.LED
Yo u
Watch Us
www.youtube.com/user/KessilTube
Join Us
www.monorad.com/forums/
Kessil Lighting
A DiCon Business Division
1689 Regatta Blvd, Richmond, CA 94804
[phone]
WWW.KESSIL.COM
KESSIL warrants, to the original buyer, all of its products to be free from defects in both workmanship and
material for a period of one year from the date of purchase. This warranty extends to all products which have
proved defective through normal use but excludes products that have been damaged, disassembled,
modified, or misused by the buyer or any other person. This warranty is in lieu of all other warranties, and
KESSIL disclaims all warranties expressed or implied, including any warranty of merchantability, fitness for
a particular purpose, or arising from the course of dealing between the parties or usage of trade.
KESSIL will replace or repair to proper working condition any products that are returned under warranty.
Products repaired or replaced under warranty are only warranted for the remaining unexpired period of time
of the original warranty.
WARRANTY
Problem Cause / Solution
Light doesn’t turn ON
Unit is flickering
Make sure the unit is connected to the power supply and the power supply is plugged into an
outlet with the correct specifications.
Make sure the power supply has the right specifications.
Make sure the unit has not overheated by operating at a room temperature exceeding 40°C.
Make sure electrical power is available to the AC outlet being used.
Make sure the power supply has the right specifications.
Make sure the device is operating within the specified operating temperature range. If unit
overheats, it will automatically shut down.
Make sure the fan is operating properly.
TROUBLESHOOTING GUIDE
MAINTENANCE
1.Keep air vent (D, F) and fan clear of dust. To clean the fan, turn unit off, insert the tip of a CO2 dust blower
(or similar dust blower) in one of the slots (F) on the unit’s outer shell. Hold and spray.
2.Keep the diffuser (G) clean. If the diffuser becomes contaminated with water, dust or other particles, turn off
the unit and clean it with isopropyl alcohol. Wet a cotton swab or a napkin in isopropyl alcohol and gently
wipe the surface of the diffuser and let it dry.
P/N : 5870008A1